scholarly journals Investigating of Turbine Blades Geometrical Change Effects on Dynamic Performance of IGT-25 Gas Turbine

2019 ◽  
Author(s):  
Nima Zamani Meymian ◽  
Hossein Rabiei
Keyword(s):  
Gas Turbine ◽  
Mass Flow ◽  
Gas Flow ◽  
Fluid Dynamic ◽  
Dynamic Performance ◽  
Turbine Blades ◽  
Gas Generator ◽  
Air Compressor ◽  
Power Turbine ◽  
Geometrical Change

In the paper, the effect of gas generator turbine blades’ geometrical change has been studied on the overall performance of a twin-shaft 25MW gas turbine with industrial application, under dynamic conditions. Geometrical changes include change of thickness and height of gas generator turbine blades which in turn would result in the change in the mass flow rate of passing hot gas, as well as isentropic efficiency in each stage of the turbine. Gas turbine modeling in the paper is zero-dimensional and takes place with consideration of dynamic effects of volume on air compressor components, combustion chamber, gas generator turbine, power turbine, fuel system, as well as effects of heat transfer dynamics between blades, gas path, and effects of operators on inlet guide vanes, fuel valves, and air compressor discharge valve. In the mathematical model of each of the components, steady-state characteristics curves have been used, extracted from 3-Dimensional computational fluid dynamics (CFD). To do so, characteristic curves of the first and second stages of the four-stage turbine have been updated through 3-D fluid dynamic analysis so that the effect of geometrical changes in turbine blades would be applied. Results from effects of these changes on characteristics of transient gas flow including output power of gas generator turbine and power turbine, inlet and outlet temperatures of turbine stages, as well as air and fuel mass flow rates have been provided from the start-ups until reaching the nominal load would be achieved.

scholarly journals Theory of gas turbine engine optimal gas generator

2019 ◽  
Vol 18 (2) ◽  
pp. 52-61
Author(s):  
A. V. Grigoriev ◽  
A. A. Kosmatov ◽  
О. A. Rudakov ◽  
A. V. Solovieva
Keyword(s):  
Combustion Chamber ◽  
Gas Turbine ◽  
Gas Flow ◽  
Turbine Blades ◽  
Target Function ◽  
Gas Turbine Engine ◽  
Gas Generator ◽  
Joint Operation ◽  
Turbine Engine ◽  
Wide Range

The article substantiates the necessity of designing an optimal gas generator of a gas turbine engine. The generator is to provide coordinated joint operation of its units: compressor, combustion chamber and compressor turbine with the purpose of reducing the period of development of new products, improving their fuel efficiency, providing operability of the blades of a high-temperature cooled compressor turbine and meeting all operational requirements related to the operation of the optimal combustion chamber including a wide range of stable combustion modes, high-altitude start at subzero air and fuel temperature conditions and prevention of the atmosphere pollution by toxic emissions. Methods of optimizing the parameters of coordinated joint operation of gas generator units are developed. These parameters include superficial flow velocities in the boundary interface cross sections between the compressor and the combustion chamber, as well as between the combustion chamber and the compressor turbine. The effective efficiency of the engine thermodynamic cycle is the optimization target function. The required depth of the turbine blades cooling is a functional constraint evaluated with account for calculations of irregularity and instability of the gas temperature field and the actual flow turbulence intensity at the blades’ inlet. We carried out theoretical analysis of the influence of various factors on the gas flow that causes changes in the flow total pressure in the channels of the gas generator gas dynamic model, i.e. changes in the efficiencies of its units. It is shown that the long period (about five years) of the engine final development time, is due to the necessity to perform expensive full-scale tests of prototypes, in particular, it is connected with an incoordinate assignment in designing the values of the flow superficial velocities in the boundary sections between the gas generator units. Designing of an optimal gas generator is only possible on the basis of an integral mathematical model of an optimal combustion chamber.

Development and Fabrication of Silicon Nitride Components for Ceramic Gas Turbine

1997 ◽  
Author(s):  
Keisuke Makino ◽  
Ken-Ichi Mizuno ◽  
Toru Shimamori
Keyword(s):  
High Temperature ◽  
Silicon Nitride ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Turbine Blades ◽  
High Strength ◽  
Inlet Temperature ◽  
Turbine Inlet Temperature ◽  
Spark Plug ◽  
Power Turbine

NGK Spark Plug Co., Ltd. has been developing various silicon nitride materials, and the technology for fabricating components for ceramic gas turbines (CGT) using theses materials. We are supplying silicon nitride material components for the project to develop 300 kW class CGT for co-generation in Japan. EC-152 was developed for components that require high strength at high temperature, such as turbine blades and turbine nozzles. In order to adapt the increasing of the turbine inlet temperature (TIT) up to 1,350 °C in accordance with the project goals, we developed two silicon nitride materials with further unproved properties: ST-1 and ST-2. ST-1 has a higher strength than EC-152 and is suitable for first stage turbine blades and power turbine blades. ST-2 has higher oxidation resistance than EC-152 and is suitable for power turbine nozzles. In this paper, we report on the properties of these materials, and present the results of evaluations of these materials when they are actually used for CGT components such as first stage turbine blades and power turbine nozzles.

Development and Evaluation of Silicon Nitride Components for Ceramic Gas Turbine

1998 ◽  
Author(s):  
Yasushi Hara ◽  
Katsura Matsubara ◽  
Ken-ichi Mizuno ◽  
Toru Shimamori ◽  
Hiro Yoshida
Keyword(s):  
Silicon Nitride ◽  
Gas Turbines ◽  
High Speed ◽  
Gas Flow ◽  
Impact Damage ◽  
Turbine Blades ◽  
Impact Testing ◽  
Particle Impact ◽  
Inlet Temperature ◽  
Power Turbine

NGK Spark Plug Co., Ltd. has been developing various silicon nitride materials, and the technology for fabricating components for ceramic gas turbines (CGT) using theses materials. We are supplying silicon nitride material components for the project to develop 300 kW class CGT for co-generation in Japan. EC-152 was developed for components that require high strength at high temperature, such as turbine blades and turbine nozzles. In order to adapt the increasing of the turbine inlet temperature (TIT) up to 1350 °C in accordance with the project goals, we developed two silicon nitride materials with further improved properties: ST-1 and ST-2. ST-1 has a higher strength than EC-152 and is suitable for first stage turbine blades and power turbine blades. ST-2 has higher oxidation resistance than EC-152 and is suitable for power turbine nozzles. On applying these silicon nitride ceramics to CGT engine, we evaluated various properties of silicon nitride materials considering the environment in CGT engine. Particle impact testing is one of those evaluations. Materials used in CGT engine are exposed in high speed gas flow, and impact damage of these materials is considered to be a concern. We tested ST-1 in the particle impact test. In this test, we observed fracture modes, and estimated the critical impact velocity. This paper summarizes the development of silicon nitride components, and the result of evaluations of these silicon nitride materials.

Capacity Matching of Aeroderivative Gas Generator With Free Power Turbine: Challenges, Uncertainties, and Opportunities

2019 ◽  
Author(s):  
Deepak Thirumurthy ◽  
Jose Carlos Casado Coca ◽  
Kanishka Suraweera
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Systems Approach ◽  
Gas Generator ◽  
Performance Guarantees ◽  
Design Variables ◽  
Performance Trends ◽  
Power Turbine ◽  
Parameter Matching ◽  
Turbine Capacity

Abstract For gas turbines with free power turbines, the capacity or flow parameter matching is of prime importance. Accurately matched capacity enables the gas turbine to run at its optimum conditions. This ensures maximum component efficiencies, and optimum shaft speeds within mechanical limits. This paper presents the challenges, uncertainties, and opportunities associated with an accurate matching of a generic two-shaft aeroderivative HP-LP gas generator with the free power turbine. Additionally, generic performance trends, uncertainty quantification, and results from the verification program are also discussed. These results are necessary to ensure that the final free power turbine capacity is within the allowable range and hence the product meets the performance guarantees. The sensitivity of free power turbine capacity to various design variables such as the vane throat area, vane trailing edge size, and manufacturing tolerance is presented. In addition, issues that may arise due to not meeting the target capacity are also discussed. To conclude, in addition to design, analysis, and statistical studies, a system-of-systems approach is mandatory to meet the allowed variation in the free power turbine capacity and hence the desired gas turbine performance.

The influence of nozzle deflection on fluid dynamic and infrared characteristics of a two-dimensional convergent–divergent vectoring exhaust system

2019 ◽  
Vol 233 (12) ◽  
pp. 4646-4662
Author(s):  
Hao Wang ◽  
Honghu Ji ◽  
Haohao Lu
Keyword(s):  
Mass Flow ◽  
Infrared Radiation ◽  
Deflection Angle ◽  
Thrust Force ◽  
Fluid Dynamic ◽  
Dynamic Performance ◽  
Exhaust System ◽  
Two Dimensional ◽  
Radiation Characteristics ◽  
Significant Information

Superior maneuverability and good infrared stealthy properties are two key points of the future aircraft. A two-dimensional convergent–divergent (2D-CD) vectoring exhaust system can improve the maneuverability of aircrafts and has been widely applied to the latest generation aircrafts. Understanding fluid dynamic and infrared radiation characteristics of the 2D-CD vectoring exhaust systems under different conditions of the nozzle deflection is very crucial, which can provide significant information for the suppression of the infrared radiation property of the 2D-CD vectoring exhaust system. In this paper, by means of computational fluid dynamics, the fluid dynamic and infrared radiation characteristics of the 2D-CD vectoring exhaust system are studied at subsonic cruise status with nozzle deflection angles from 0 to 20°, and the results are compared with those of the baseline axisymmetric exhaust system. The results indicate that the fluid dynamic performance of a properly designed 2D-CD vectoring exhaust system is equivalent to the fluid dynamic performance of the baseline axisymmetric exhaust system. When the nozzle deflection angle is less than 5°, the mass flow and thrust force of the 2D-CD vectoring exhaust system are almost unchanged, and with the increase of the nozzle deflection angles, the mass flow and thrust force decrease rapidly. The thrust force deflection angles lag behind the nozzle deflection angles all the time, and as the nozzle deflection angle increases, the difference between them decreases. The direction of the maximum infrared radiation of the 2D-CD vectoring exhaust system deflects with the deflection of the nozzle, and the mean integrated infrared radiation intensity of the exhaust system decreases with the increase of nozzle deflection angles.

scholarly journals Conceptual Mean-Line Design of Single and Twin-Shaft Oxy-Fuel Gas Turbine in a Semiclosed Oxy-Fuel Combustion Combined Cycle

2013 ◽  
Vol 135 (8) ◽  
Author(s):  
Majed Sammak ◽  
Egill Thorbergsson ◽  
Tomas Grönstedt ◽  
Magnus Genrup
Keyword(s):  
Mach Number ◽  
Gas Turbine ◽  
Mass Flow ◽  
Rotational Speed ◽  
Gas Turbines ◽  
Combined Cycle ◽  
Fuel Gas ◽  
Power Turbine ◽  
Exit Mach Number ◽  
Line Design

The aim of this study was to compare single- and twin-shaft oxy-fuel gas turbines in a semiclosed oxy-fuel combustion combined cycle (SCOC–CC). This paper discussed the turbomachinery preliminary mean-line design of oxy-fuel compressor and turbine. The conceptual turbine design was performed using the axial through-flow code luax-t, developed at Lund University. A tool for conceptual design of axial compressors developed at Chalmers University was used for the design of the compressor. The modeled SCOC–CC gave a net electrical efficiency of 46% and a net power of 106 MW. The production of 95% pure oxygen and the compression of CO2 reduced the gross efficiency of the SCOC–CC by 10 and 2 percentage points, respectively. The designed oxy-fuel gas turbine had a power of 86 MW. The rotational speed of the single-shaft gas turbine was set to 5200 rpm. The designed turbine had four stages, while the compressor had 18 stages. The turbine exit Mach number was calculated to be 0.6 and the calculated value of AN2 was 40 · 106 rpm2m2. The total calculated cooling mass flow was 25% of the compressor mass flow, or 47 kg/s. The relative tip Mach number of the compressor at the first rotor stage was 1.15. The rotational speed of the twin-shaft gas generator was set to 7200 rpm, while that of the power turbine was set to 4800 rpm. A twin-shaft turbine was designed with five turbine stages to maintain the exit Mach number around 0.5. The twin-shaft turbine required a lower exit Mach number to maintain reasonable diffuser performance. The compressor turbine was designed with two stages while the power turbine had three stages. The study showed that a four-stage twin-shaft turbine produced a high exit Mach number. The calculated value of AN2 was 38 · 106 rpm2m2. The total calculated cooling mass flow was 23% of the compressor mass flow, or 44 kg/s. The compressor was designed with 14 stages. The preliminary design parameters of the turbine and compressor were within established industrial ranges. From the results of this study, it was concluded that both single- and twin-shaft oxy-fuel gas turbines have advantages. The choice of a twin-shaft gas turbine can be motivated by the smaller compressor size and the advantage of greater flexibility in operation, mainly in the off-design mode. However, the advantages of a twin-shaft design must be weighed against the inherent simplicity and low cost of the simple single-shaft design.

Flow Assessment on the Effects of Water Droplets on Rotor Region of Wet Compression

2017 ◽  
Vol 374 ◽  
pp. 131-147
Author(s):  
Gambo Kofar Bai Dayyabu ◽  
Hai Zhang ◽  
Qun Zheng ◽  
Salman Abdu
Keyword(s):  
Gas Turbine ◽  
Gas Flow ◽  
Fluid Dynamic ◽  
Inlet Temperature ◽  
Outlet Temperature ◽  
Water Droplets ◽  
Compression Process ◽  
Transonic Compressor ◽  
Depth Analysis ◽  
Wet Compression

Wet compression process has been widely accepted as a measure of increasing the performance of industrial gas turbine, in the present work, in-depth analysis on the principle aspects of wet compression, more specifically, the influence of injected water droplets diameter, surface temperature, and their effects on the behavior of axial flow transonic compressor and gas turbine performance were analyzed using computational fluid dynamic. Injected water droplets and gas flow phase change was most intense in the area adjacent to shockwaves and were the slip velocity of the droplet is highest. Water injection in to the compressor rotor is a little perturbation to the flow field due to the formation of flow separation, evaporation rate, increasing weber number, reduction in the inlet temperature, and velocity vortex pattern relatively different from that of the dry case. The effects of water droplets on the rotor region at injection rate of 1%, shows decrease in the inlet temperature of 11%, outlet temperature 5% and uplift the efficiency to 1.5%.

Development US Navy Gas Turbine Vibration Analysis Expertise: LM2500 Vibration and Trim Balance

2012 ◽  
Author(s):  
Bruce D. Thompson ◽  
Jurie Grobler
Keyword(s):  
Gas Turbine ◽  
Turbine Rotor ◽  
Gas Generator ◽  
Engine Operation ◽  
Engine Design ◽  
Power Turbine ◽  
Us Navy ◽  
Continued Use ◽  
Integrated Performance ◽  
Mean Time

Although generally reliable in-service and with an ever increasing mean time between removal, it was identified in the mid to late 1980’s that the LM2500 gas turbine in US Navy service had a problem with self generated vibration; this was principally due to imbalance in the gas generator or power turbine rotor, however, other non-synchronous sources for vibration were discovered to be important as well. The initial method for resolving this problem was to remove and repair, at a depot, the engines that exceeded the in-service alarm level. This turned out to be a very expensive approach and it was found that most engines that had excessive vibration levels in other respects (performance, etc.) were perfectly acceptable for continued use without repair. Raising the vibration alarm level was tried for a time. However, it became clear that prolonged engine operation with higher levels of vibration were detrimental to the mechanical integrity of the engine. This paper discusses the systematic approach developed to reduce LM2500 self generated vibration levels. This included monitoring system improvements, engine design & hardware improvements and the development and implementation of in-place trim balance. This paper also discusses some of the analysis and practical difficulties encountered reducing and maintaining low LM2500 vibration levels through trim balance and by other means. Also discussed is the present implementation of remotely monitoring LM2500 operating parameters, in particular vibration, through the Integrated Performance Analysis Reports (IPAR) and the Maintenance Engineering Library Server (MELS).

Unbalance Response of a Two Spool Gas Turbine Engine With Squeeze Film Bearings

1981 ◽  
Author(s):  
E. J. Gunter ◽  
D. F. Li ◽  
L. E. Barrett
Keyword(s):  
Gas Turbine ◽  
Nonlinear Effects ◽  
Forced Response ◽  
Squeeze Film ◽  
Gas Generator ◽  
Main Bearing ◽  
Resonant Condition ◽  
Turbine Engine ◽  
Generator Rotor ◽  
Power Turbine

This paper presents a dynamic analysis of a two-spool gas turbine helicopter engine incorporating intershaft rolling element bearings between the gas generator and power turbine rotors. The analysis includes the nonlinear effects of a squeeze film bearing incorporated on the gas generator rotor. The analysis includes critical speeds and forced response of the system and indicates that substantial dynamic loads may be imposed on the intershaft bearings and main bearing supports with an improperly designed squeeze film bearing. A comparison of theoretical and experimental gas generator rotor response is presented illustrating the nonlinear characteristics of the squeeze film bearing. It was found that large intershaft bearing forces may occur even though the engine is not operating at a resonant condition.

Numerical Analysis of the Effects of Non-Uniform Surface Roughness on Compressor Stage Performance

2010 ◽  
Author(s):  
Mirko Morini ◽  
Michele Pinelli ◽  
Pier Ruggero Spina ◽  
Mauro Venturini
Keyword(s):  
Surface Roughness ◽  
Gas Turbine ◽  
Traditional Approach ◽  
Fluid Dynamic ◽  
Turbine Blades ◽  
Compressor Stage ◽  
Turbine Performance ◽  
Performance Map ◽  
Overall Performance ◽  
Stage Performance

Gas turbine performance degradation over time is mainly due to the deterioration of compressor and turbine blades, which, in turn, causes a modification of the compressor and turbine performance maps. Since detailed information about the actual modification of the compressor and turbine performance maps is usually unavailable, component performance can be modeled and investigated (i) by scaling the overall performance map, or (ii) by using stage-by-stage models of the compressor and turbine and by scaling each single stage performance map to account for each stage deterioration, or (iii) by performing 3D numerical simulations, which allow to both highlight the fluid-dynamic phenomena occurring in the faulty component and grasp the effect on the overall performance of the component. In this paper, the authors address the most common and experienced source of loss for a gas turbine, i.e. compressor fouling. With respect to the traditional approach, which mainly aims at the identification of the overall effects of fouling, authors investigate a micro-scale representation of compressor fouling (e.g. blade surface deterioration and flow deviation). This allows (i) a more detailed investigation of the fouling effects (e.g. mechanism, location along blade height, etc.), (ii) a more extensive analysis of the causes of performance deterioration and (iii) the assessment of the effect of fouling on stage performance coefficients and on stage performance maps. The effects of a non-uniform surface roughness on both rotor and stator blades of an axial compressor stage are investigated by using a commercial CFD code. The NASA Stage 37 test case was used as the baseline geometry. The numerical model already validated against experimental data available in literature was used for the simulations. Different non-uniform combinations of surface roughness levels on rotor and stator blades were imposed. This makes it possible to highlight how the localization of fouling on compressor blades affects compressor performance, both at an overall and at a fluid-dynamic level.

Sign in / Sign up

Export Citation Format

Share Document