Copper Bond Over Active Circuit (BOAC) and Copper Over Anything (COA) Failure Analysis

2003 ◽  
Author(s):  
Dat Nguyen ◽  
Bob Davis ◽  
Corey Lewis
Keyword(s):  
Integrated Circuits ◽  
Failure Analysis ◽  
Fault Isolation ◽  
Circuit Boards ◽  
Electronic Industry ◽  
Cause Analysis ◽  
Defect Identification ◽  
Root Cause ◽  
Active Circuit ◽  
Selective Analysis

Abstract In today's electronic industry of shrinking circuit boards and shrinking semiconductor integrated circuits (IC), semiconductor companies have to be creative in providing devices with more circuitry on less silicon. Copper Bond over Active Circuit (BOAC)/Copper over Anything (COA) processes allow routing and bonding to thick top level metallization on the LinBiCMOS technology node. This paper discusses failure analysis (FA) techniques and approaches on un-passivated BOAC, and explains a generic BOAC/COA process. The approach to FA of BOAC involves package inspection-non intrusive analysis, decapsulation, die inspection, and defect identification/root cause analysis. Case studies are presented to explain the specific FA steps. Fault isolation involving BOAC requires the strategic removal of copper traces and selective analysis of the failed circuitry. Liquid crystal and micro-probing have been used effectively in failure isolation.

Root Cause Analysis Techniques Using Picosecond Time Resolved LADA

2014 ◽  
Author(s):  
Dan Bodoh ◽  
Kent Erington ◽  
Kris Dickson ◽  
George Lange ◽  
Carey Wu ◽  
...  
Keyword(s):  
Integrated Circuits ◽  
Picosecond Laser ◽  
Root Cause Analysis ◽  
Fault Isolation ◽  
Time Resolved ◽  
Cause Analysis ◽  
Root Cause ◽  
Design And Manufacturing ◽  
Multiple Interactions ◽  
Established Technique

Abstract Laser-assisted device alteration (LADA) is an established technique used to identify critical speed paths in integrated circuits. LADA can reveal the physical location of a speed path, but not the timing of the speed path. This paper describes the root cause analysis benefits of 1064nm time resolved LADA (TR-LADA) with a picosecond laser. It shows several examples of how picosecond TR-LADA has complemented the existing fault isolation toolset and has allowed for quicker resolution of design and manufacturing issues. The paper explains how TR-LADA increases the LADA localization resolution by eliminating the well interaction, provides the timing of the event detected by LADA, indicates the propagation direction of the critical signals detected by LADA, allows the analyst to infer the logic values of the critical signals, and separates multiple interactions occurring at the same site for better understanding of the critical signals.

Challenges of System Level Failure Analysis of Electronics in the Automotive Industry

2017 ◽  
Author(s):  
Bence Hevesi
Keyword(s):  
Failure Analysis ◽  
Case Studies ◽  
Automotive Industry ◽  
Root Cause Analysis ◽  
Fault Isolation ◽  
System Level ◽  
Cause Analysis ◽  
Root Cause ◽  
Analysis Workflow

Abstract In this paper, different failure analysis (FA) workflows are showed which combines different FA approaches for fast and efficient fault isolation and root cause analysis in system level products. Two case studies will be presented to show the importance of a well-adjusted failure analysis workflow.

Failure Analysis and Process Verification of High-Density Copper ICs Used in Multichip Modules

2017 ◽  
Author(s):  
Jeremy A. Walraven ◽  
Mark W. Jenkins ◽  
Tuyet N. Simmons ◽  
James E. Levy ◽  
Sara E. Jensen ◽  
...  
Keyword(s):  
Integrated Circuits ◽  
Failure Analysis ◽  
Root Cause Analysis ◽  
Multichip Modules ◽  
Cause Analysis ◽  
Process Verification ◽  
Root Cause ◽  
Corrective Actions ◽  
Silicon Vias ◽  
Metal Layers

Abstract Manufacturing of integrated circuits (ICs) using a split foundry process expands design space in IC fabrication by employing unique capabilities of multiple foundries and provides added security for IC designers [1]. Defect localization and root cause analysis is critical to failure identification and implementation of corrective actions. In addition to split-foundry fabrication, the device addressed in this publication is comprised of 8 metal layers, aluminum test pads, and tungsten thru-silicon vias (TSVs) making the circuit area > 68% metal. This manuscript addresses the failure analysis efforts involved in root cause analysis, failure analysis findings, and the corrective actions implemented to eliminate these failure mechanisms from occurring in future product.

Laser Voltage Probing in Failure Analysis of Advanced Integrated Circuits on SOI

2012 ◽  
Author(s):  
V.K. Ravikumar ◽  
R. Wampler ◽  
M.Y. Ho ◽  
J. Christensen ◽  
S.L. Phoa
Keyword(s):  
Integrated Circuits ◽  
Failure Analysis ◽  
Case Studies ◽  
Timing Analysis ◽  
Fault Isolation ◽  
Root Cause ◽  
Root Cause Identification

Abstract Laser voltage probing is the newest generation of tools that perform timing analysis for electrical fault isolation in advanced failure analysis facilities. This paper uses failure analysis case studies on SOI to showcase the implementation of laser voltage probing in the failure analysis flow and highlight its significance in root-cause identification.

Defect Localization and Root Cause Analysis on e-Fuse Read Reliability Failure

2014 ◽  
Author(s):  
Hung Chin Chen ◽  
Chih Yang Tsai ◽  
Shih Yuan Liu ◽  
Yu Pang Chang ◽  
Jian Chang Lin
Keyword(s):  
Failure Analysis ◽  
Focused Ion Beam ◽  
Metal Layer ◽  
Ion Beam ◽  
Fault Isolation ◽  
Resistance Change ◽  
Cause Analysis ◽  
Root Cause ◽  
Failure Location ◽  
Rate Of Failure

Abstract Fault isolation is the most important step for Failure Analysis (FA), and it is closely linked with the success rate of failure mechanism finding. In this paper, we will introduce a case that hard to debug with traditional FA skills. In order to find out its root cause, several advanced techniques such as layout tracing, circuit edit and Infrared Ray–Optical Beam Induced Resistance Change (IR-OBIRCH) analysis had been applied. The circuit edit was performed following layout tracing for depositing probing pads by Focused Ion Beam (FIB). Then, IR-OBIRCH analysis with biasing on the two FIB deposited probing pads and a failure location was detected. Finally, the root cause of inter- metal layer bridge was found in subsequent physical failure analysis.

A New Failure Analysis Flow of Gate Oxide Integrity Failure in Wafer Fabrication

2009 ◽  
Author(s):  
Hua Younan ◽  
Chu Susan ◽  
Gui Dong ◽  
Mo Zhiqiang ◽  
Xing Zhenxiang ◽  
...  
Keyword(s):  
Failure Analysis ◽  
Gate Dielectric ◽  
Dielectric Breakdown ◽  
Defect Density ◽  
Gate Oxide ◽  
Oxide Thickness ◽  
Fault Isolation ◽  
Wafer Fabrication ◽  
Root Cause ◽  
Gate Oxide Integrity

Abstract As device feature size continues to shrink, the reducing gate oxide thickness puts more stringent requirements on gate dielectric quality in terms of defect density and contamination concentration. As a result, analyzing gate oxide integrity and dielectric breakdown failures during wafer fabrication becomes more difficult. Using a traditional FA flow and methods some defects were observed after electrical fault isolation using emission microscopic tools such as EMMI and TIVA. Even with some success with conventional FA the root cause was unclear. In this paper, we will propose an analysis flow for GOI failures to improve FA’s success rate. In this new proposed flow both a chemical method, Wright Etch, and SIMS analysis techniques are employed to identify root cause of the GOI failures after EFA fault isolation. In general, the shape of the defect might provide information as to the root cause of the GOI failure, whether related to PID or contamination. However, Wright Etch results are inadequate to answer the questions of whether the failure is caused by contamination or not. If there is a contaminate another technique is required to determine what the contaminant is and where it comes from. If the failure is confirmed to be due to contamination, SIMS is used to further determine the contamination source at the ppm-ppb level. In this paper, a real case of GOI failure will be discussed and presented. Using the new failure analysis flow, the root cause was identified to be iron contamination introduced from a worn out part made of stainless steel.

Novel FIB Use for Failure Analysis of MEMS Gyroscopes

2016 ◽  
Author(s):  
Nathan Wang ◽  
Saunil Shah ◽  
Camille Garcia ◽  
Vicente Pasating ◽  
George Perreault
Keyword(s):  
Thin Films ◽  
Integrated Circuits ◽  
Failure Analysis ◽  
New Techniques ◽  
Unique Challenge ◽  
Root Cause ◽  
Large Size ◽  
Mems Gyroscopes

Abstract MEMS samples, with their relatively large size and weight, present a unique challenge to the failure analyst as they also included thin films and microstructures used in conventional integrated circuits. This paper describes how to accommodate the large MEMS structures without skimping on the microanalyses needed to get to the root cause. Investigations of tuning folk gyroscopes were used to demonstrate these new techniques.

Root Cause Analysis for Pin Leakage

2016 ◽  
Author(s):  
Zhigang Song ◽  
Jochonia Nxumalo ◽  
Manuel Villalobos ◽  
Sweta Pendyala
Keyword(s):  
Failure Analysis ◽  
Root Cause Analysis ◽  
Advanced Technology ◽  
Process Step ◽  
Cause Analysis ◽  
Hard Mask ◽  
Technology Node ◽  
Root Cause ◽  
Tools And Techniques

Abstract Pin leakage continues to be on the list of top yield detractors for microelectronics devices. It is simply manifested as elevated current with one pin or several pins during pin continuity test. Although many techniques are capable to globally localize the fault of pin leakage, root cause analysis and identification for it are still very challenging with today’s advanced failure analysis tools and techniques. It is because pin leakage can be caused by any type of defect, at any layer in the device and at any process step. This paper presents a case study to demonstrate how to combine multiple techniques to accurately identify the root cause of a pin leakage issue for a device manufactured using advanced technology node. The root cause was identified as under-etch issue during P+ implantation hard mask opening for ESD protection diode, causing P+ implantation missing, which was responsible for the nearly ohmic type pin leakage.

Pseudo-Dynamic Fault Isolation Technique Using Backside Emission Microscopy – Case Study, Where All Other Methods Fail

2002 ◽  
Author(s):  
Yoav Weizman ◽  
Ezra Baruch ◽  
Michael Zimin
Keyword(s):  
Failure Analysis ◽  
Process Variations ◽  
Fault Isolation ◽  
Operating Conditions ◽  
Detection Sensitivity ◽  
Isolation Technique ◽  
Root Cause ◽  
Emission Microscopy ◽  
Failure Location ◽  
Noisy Background

Abstract Emission microscopy is usually implemented for static operating conditions of the DUT. Under dynamic operation it is nearly impossible to identify a failure out of the noisy background. In this paper we describe a simple technique that could be used in cases where the temporal location of the failure was identified however the physical location is not known or partially known. The technique was originally introduced to investigate IDDq failures (1) in order to investigate timing related issues with automated tester equipment. Ishii et al (2) improved the technique and coupled an emission microscope to the tester for functional failure analysis of DRAMs and logic LSIs. Using consecutive step-by-step tester halting coupled to a sensitive emission microscope, one is able detect the failure while it occurs. We will describe a failure analysis case in which marginal design and process variations combined to create contention at certain logic states. Since the failure occurred arbitrarily, the use of the traditional LVP, that requires a stable failure, misled the analysts. Furthermore, even if we used advanced tools as PICA, which was actually designed to locate such failures, we believe that there would have been little chance of observing the failure since the failure appeared only below 1.3V where the PICA tool has diminished photon detection sensitivity. For this case the step-by-step halting technique helped to isolate the failure location after a short round of measurements. With the use of logic simulations, the root cause of the failure was clear once the failing gate was known.

Application of Advanced Back-Side Optical Techniques in ASICs

2013 ◽  
Vol 21 (3) ◽  
pp. 30-35
Author(s):  
Douglas Martin ◽  
Samuel Beilin ◽  
Brett Hamilton ◽  
Darin York ◽  
Philip Baker ◽  
...  
Keyword(s):  
Integrated Circuits ◽  
Failure Analysis ◽  
Photon Emission ◽  
Back Side ◽  
Voltage Imaging ◽  
Root Cause ◽  
Silicon Transistors ◽  
Cause Of Failure ◽  
Metal Interconnects ◽  
Application Specific

Failure analysis is important in determining root cause for appropriate corrective action. In order to perform failure analysis of microelectronic application-specific integrated circuits (ASICs) delidding the device is often required. However, determining root cause from the front side is not always possible due to shadowing effects caused by the ASIC metal interconnects. Therefore, back-side polishing is used to reveal an unobstructed view of the ASIC silicon transistors. This paper details how back-side polishing in conjunction with laser-scanned imaging (LSI), laser voltage imaging (LVI), laser voltage probing (LVP), photon emission microscopy (PEM), and laser-assisted device alterations (LADA) were used to uncover the root cause of failure of two ASICs.

Sign in / Sign up

Export Citation Format

Share Document