Laser Voltage Probing in Failure Analysis of Advanced Integrated Circuits on SOI

2012 ◽  
Author(s):  
V.K. Ravikumar ◽  
R. Wampler ◽  
M.Y. Ho ◽  
J. Christensen ◽  
S.L. Phoa
Keyword(s):  
Integrated Circuits ◽  
Failure Analysis ◽  
Case Studies ◽  
Timing Analysis ◽  
Fault Isolation ◽  
Root Cause ◽  
Root Cause Identification

Abstract Laser voltage probing is the newest generation of tools that perform timing analysis for electrical fault isolation in advanced failure analysis facilities. This paper uses failure analysis case studies on SOI to showcase the implementation of laser voltage probing in the failure analysis flow and highlight its significance in root-cause identification.

Challenges of System Level Failure Analysis of Electronics in the Automotive Industry

2017 ◽  
Author(s):  
Bence Hevesi
Keyword(s):  
Failure Analysis ◽  
Case Studies ◽  
Automotive Industry ◽  
Root Cause Analysis ◽  
Fault Isolation ◽  
System Level ◽  
Cause Analysis ◽  
Root Cause ◽  
Analysis Workflow

Abstract In this paper, different failure analysis (FA) workflows are showed which combines different FA approaches for fast and efficient fault isolation and root cause analysis in system level products. Two case studies will be presented to show the importance of a well-adjusted failure analysis workflow.

MEMS Failure Analysis In Wafer Fabrication

2016 ◽  
Author(s):  
Hui Peng Ng ◽  
Angela Teo ◽  
Ghim Boon Ang ◽  
Alfred Quah ◽  
N. Dayanand ◽  
...  
Keyword(s):  
Failure Analysis ◽  
Case Studies ◽  
Data Interpretation ◽  
Fault Isolation ◽  
Wafer Fabrication ◽  
Auger Analysis ◽  
Root Cause ◽  
Defect Site ◽  
Defect Localization ◽  
Cmos Chip

Abstract This paper discussed on how the importance of failure analysis to identify the root cause and mechanism that resulted in the MEMS failure. The defect seen was either directly on the MEMS caps or the CMOS integrated chip in wafer fabrication. Two case studies were highlighted in the discussion to demonstrate how the FA procedures that the analysts had adopted in order to narrow down to the defect site successfully on MEMS cap as well as on CMOS chip on MEMS package units. Besides the use of electrical fault isolation tool/technique such as TIVA for defect localization, a new physical deprocessing approach based on the cutting method was performed on the MEMS package unit in order to separate the MEMS from the Si Cap. This approach would definitely help to prevent the introduction of particles and artifacts during the PFA that could mislead the FA analyst into wrong data interpretation. Other FA tool such as SEM inspection to observe the physical defect and Auger analysis to identify the elements in the defect during the course of analysis were also documented in this paper.

Copper Bond Over Active Circuit (BOAC) and Copper Over Anything (COA) Failure Analysis

2003 ◽  
Author(s):  
Dat Nguyen ◽  
Bob Davis ◽  
Corey Lewis
Keyword(s):  
Integrated Circuits ◽  
Failure Analysis ◽  
Fault Isolation ◽  
Circuit Boards ◽  
Electronic Industry ◽  
Cause Analysis ◽  
Defect Identification ◽  
Root Cause ◽  
Active Circuit ◽  
Selective Analysis

Abstract In today's electronic industry of shrinking circuit boards and shrinking semiconductor integrated circuits (IC), semiconductor companies have to be creative in providing devices with more circuitry on less silicon. Copper Bond over Active Circuit (BOAC)/Copper over Anything (COA) processes allow routing and bonding to thick top level metallization on the LinBiCMOS technology node. This paper discusses failure analysis (FA) techniques and approaches on un-passivated BOAC, and explains a generic BOAC/COA process. The approach to FA of BOAC involves package inspection-non intrusive analysis, decapsulation, die inspection, and defect identification/root cause analysis. Case studies are presented to explain the specific FA steps. Fault isolation involving BOAC requires the strategic removal of copper traces and selective analysis of the failed circuitry. Liquid crystal and micro-probing have been used effectively in failure isolation.

A New Failure Analysis Flow of Gate Oxide Integrity Failure in Wafer Fabrication

2009 ◽  
Author(s):  
Hua Younan ◽  
Chu Susan ◽  
Gui Dong ◽  
Mo Zhiqiang ◽  
Xing Zhenxiang ◽  
...  
Keyword(s):  
Failure Analysis ◽  
Gate Dielectric ◽  
Dielectric Breakdown ◽  
Defect Density ◽  
Gate Oxide ◽  
Oxide Thickness ◽  
Fault Isolation ◽  
Wafer Fabrication ◽  
Root Cause ◽  
Gate Oxide Integrity

Abstract As device feature size continues to shrink, the reducing gate oxide thickness puts more stringent requirements on gate dielectric quality in terms of defect density and contamination concentration. As a result, analyzing gate oxide integrity and dielectric breakdown failures during wafer fabrication becomes more difficult. Using a traditional FA flow and methods some defects were observed after electrical fault isolation using emission microscopic tools such as EMMI and TIVA. Even with some success with conventional FA the root cause was unclear. In this paper, we will propose an analysis flow for GOI failures to improve FA’s success rate. In this new proposed flow both a chemical method, Wright Etch, and SIMS analysis techniques are employed to identify root cause of the GOI failures after EFA fault isolation. In general, the shape of the defect might provide information as to the root cause of the GOI failure, whether related to PID or contamination. However, Wright Etch results are inadequate to answer the questions of whether the failure is caused by contamination or not. If there is a contaminate another technique is required to determine what the contaminant is and where it comes from. If the failure is confirmed to be due to contamination, SIMS is used to further determine the contamination source at the ppm-ppb level. In this paper, a real case of GOI failure will be discussed and presented. Using the new failure analysis flow, the root cause was identified to be iron contamination introduced from a worn out part made of stainless steel.

SEM-Based Nanoprobing on 40, 32 and 28 nm CMOS Devices Challenges for Semiconductor Failure Analysis

2013 ◽  
Author(s):  
Erik Paul ◽  
Holger Herzog ◽  
Sören Jansen ◽  
Christian Hobert ◽  
Eckhard Langer
Keyword(s):  
Electron Microscope ◽  
High Resolution ◽  
Scanning Electron Microscope ◽  
Failure Analysis ◽  
Case Studies ◽  
State Of The Art ◽  
Root Cause ◽  
Highly Efficient ◽  
Technology Nodes ◽  
Scanning Electron

Abstract This paper presents an effective device-level failure analysis (FA) method which uses a high-resolution low-kV Scanning Electron Microscope (SEM) in combination with an integrated state-of-the-art nanomanipulator to locate and characterize single defects in failing CMOS devices. The presented case studies utilize several FA-techniques in combination with SEM-based nanoprobing for nanometer node technologies and demonstrate how these methods are used to investigate the root cause of IC device failures. The methodology represents a highly-efficient physical failure analysis flow for 28nm and larger technology nodes.

Combine Micro-Probing and OBIRCH to Catch Non-Recognizable Fault in RF and Mixed-Mode Integrated Circuits

2007 ◽  
Author(s):  
Cha-Ming Shen ◽  
Yen-Long Chang ◽  
Lian-Fon Wen ◽  
Tan-Chen Chuang ◽  
Shi-Chen Lin ◽  
...  
Keyword(s):  
Integrated Circuits ◽  
Radio Frequency ◽  
Failure Analysis ◽  
Case Studies ◽  
Mixed Mode ◽  
Failure Mechanisms ◽  
Deep Submicron ◽  
Digital Logic ◽  
Successful Approach ◽  
Cmos Processes

Abstract Highly-integrated radio frequency and mixed-mode devices that are manufactured in deep-submicron or more advanced CMOS processes are becoming more complex to analyze. The increased complexity presents us with many eccentric failure mechanisms that are uniquely different from traditional failure mechanisms found during failure analysis on digital logic applications. This paper presents a novel methodology to overcome the difficulties and discusses two case studies which demonstrate the application of the methodology. Through the case studies, the methodology was proven to be a successful approach. It is also proved how this methodology would work for such non-recognizable failures.

Root Cause Analysis Techniques Using Picosecond Time Resolved LADA

2014 ◽  
Author(s):  
Dan Bodoh ◽  
Kent Erington ◽  
Kris Dickson ◽  
George Lange ◽  
Carey Wu ◽  
...  
Keyword(s):  
Integrated Circuits ◽  
Picosecond Laser ◽  
Root Cause Analysis ◽  
Fault Isolation ◽  
Time Resolved ◽  
Cause Analysis ◽  
Root Cause ◽  
Design And Manufacturing ◽  
Multiple Interactions ◽  
Established Technique

Abstract Laser-assisted device alteration (LADA) is an established technique used to identify critical speed paths in integrated circuits. LADA can reveal the physical location of a speed path, but not the timing of the speed path. This paper describes the root cause analysis benefits of 1064nm time resolved LADA (TR-LADA) with a picosecond laser. It shows several examples of how picosecond TR-LADA has complemented the existing fault isolation toolset and has allowed for quicker resolution of design and manufacturing issues. The paper explains how TR-LADA increases the LADA localization resolution by eliminating the well interaction, provides the timing of the event detected by LADA, indicates the propagation direction of the critical signals detected by LADA, allows the analyst to infer the logic values of the critical signals, and separates multiple interactions occurring at the same site for better understanding of the critical signals.

Novel FIB Use for Failure Analysis of MEMS Gyroscopes

2016 ◽  
Author(s):  
Nathan Wang ◽  
Saunil Shah ◽  
Camille Garcia ◽  
Vicente Pasating ◽  
George Perreault
Keyword(s):  
Thin Films ◽  
Integrated Circuits ◽  
Failure Analysis ◽  
New Techniques ◽  
Unique Challenge ◽  
Root Cause ◽  
Large Size ◽  
Mems Gyroscopes

Abstract MEMS samples, with their relatively large size and weight, present a unique challenge to the failure analyst as they also included thin films and microstructures used in conventional integrated circuits. This paper describes how to accommodate the large MEMS structures without skimping on the microanalyses needed to get to the root cause. Investigations of tuning folk gyroscopes were used to demonstrate these new techniques.

Pseudo-Dynamic Fault Isolation Technique Using Backside Emission Microscopy – Case Study, Where All Other Methods Fail

2002 ◽  
Author(s):  
Yoav Weizman ◽  
Ezra Baruch ◽  
Michael Zimin
Keyword(s):  
Failure Analysis ◽  
Process Variations ◽  
Fault Isolation ◽  
Operating Conditions ◽  
Detection Sensitivity ◽  
Isolation Technique ◽  
Root Cause ◽  
Emission Microscopy ◽  
Failure Location ◽  
Noisy Background

Abstract Emission microscopy is usually implemented for static operating conditions of the DUT. Under dynamic operation it is nearly impossible to identify a failure out of the noisy background. In this paper we describe a simple technique that could be used in cases where the temporal location of the failure was identified however the physical location is not known or partially known. The technique was originally introduced to investigate IDDq failures (1) in order to investigate timing related issues with automated tester equipment. Ishii et al (2) improved the technique and coupled an emission microscope to the tester for functional failure analysis of DRAMs and logic LSIs. Using consecutive step-by-step tester halting coupled to a sensitive emission microscope, one is able detect the failure while it occurs. We will describe a failure analysis case in which marginal design and process variations combined to create contention at certain logic states. Since the failure occurred arbitrarily, the use of the traditional LVP, that requires a stable failure, misled the analysts. Furthermore, even if we used advanced tools as PICA, which was actually designed to locate such failures, we believe that there would have been little chance of observing the failure since the failure appeared only below 1.3V where the PICA tool has diminished photon detection sensitivity. For this case the step-by-step halting technique helped to isolate the failure location after a short round of measurements. With the use of logic simulations, the root cause of the failure was clear once the failing gate was known.

A New Approach for SRAM Soft Defect Root Cause Identification

2007 ◽  
Author(s):  
Peter Egger ◽  
Stefan Müller ◽  
Martin Stiftinger
Keyword(s):  
Integrated Circuits ◽  
Top Down ◽  
Feature Size ◽  
Design Rules ◽  
New Approach ◽  
Root Cause ◽  
Wafer Fab ◽  
Sram Cell ◽  
Tcad Simulation ◽  
Root Cause Identification

Abstract With shrinking feature size of integrated circuits traditional FA techniques like SEM inspection of top down delayered devices or cross sectioning often cannot determine the physical root cause. Inside SRAM blocks the aggressive design rules of transistor parameters can cause a local mismatch and therefore a soft fail of a single SRAM cell. This paper will present a new approach to identify a physical root cause with the help of nano probing and TCAD simulation to allow the wafer fab to implement countermeasures.

Sign in / Sign up

Export Citation Format

Share Document