scholarly journals Investigation of the properties of composite materials based on epoxy resins with microsilica additives

2021 ◽  
Vol 318 (3) ◽  
pp. 63-70
Author(s):  
M.A. Serekpayeva ◽  
◽  
G.А. Kokayeva ◽  
R.K. Niyazbekova ◽  
S. Kardybai ◽  
...  
Keyword(s):  
Composite Materials ◽  
Epoxy Resin ◽  
Corrosion Protection ◽  
Epoxy Resins ◽  
Machine Maintenance ◽  
Resistance Increase ◽  
Dispersed Filler ◽  
Filler Particles

The outcomes of studying epoxy-based composite materials supplemented with microsilica are provided in the article. Microsilica was used as a filler. The samples were produced on the epoxy ED-20 basis supplemented with 2, 5 and 10 mas. % of microsilica. The structure and size of finely dispersed filler particles were defined. The obtained composites were tested for resistance to the effect of variable temperatures, corrosive, and abrasion. The study outcomes proved that samples supplemented with 2% of microsilica are more resistant to acid and alkali as well as to petrol than those ones supplemented with 25% of microsilica. Besides the amount of the filler from 2 to 10% doesn’t sufficiently affect the resistance to variable temperatures. When microsilica is added to epoxy resin, it causes scuff resistance increase. The conducted testing proved that the developed composite materials are resistant to the effect of variable temperatures, corrosive, and abrasion. This enables to use these materials as coatings and anti-corrosion protection during machine maintenance.

The Mechanical Properties of Organic Modified Epoxy Resin

2020 ◽  
Vol 43 (3) ◽  
pp. 10-14
Author(s):  
Georgel MIHU ◽  
Claudia Veronica UNGUREANU ◽  
Vasile BRIA ◽  
Marina BUNEA ◽  
Rodica CHIHAI PEȚU ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Composite Materials ◽  
Epoxy Resin ◽  
Epoxy Matrix ◽  
Epoxy Resins ◽  
Mechanical Tests ◽  
Organic Modification ◽  
Three Point Bending ◽  
Modified Epoxy

Epoxy resins have been presenting a lot of scientific and technical interests and organic modified epoxy resins have recently receiving a great deal of attention. For obtaining the composite materials with good mechanical proprieties, a large variety of organic modification agents were used. For this study gluten and gelatin had been used as modifying agents thinking that their dispersion inside the polymer could increase the polymer biocompatibility. Equal amounts of the proteins were milled together and the obtained compound was used to form 1 to 5% weight ratios organic agents modified epoxy materials. To highlight the effect of these proteins in epoxy matrix mechanical tests as three-point bending and compression were performed.

scholarly journals Mechanical properties (Tensile, Hardness and Shock resistance) for the phenol formaldehyde resin with Epoxy resin

2019 ◽  
Vol 12 (2) ◽  
pp. 35-43
Author(s):  
Mustafa A. Rajab
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Composite Materials ◽  
Epoxy Resin ◽  
Epoxy Resins ◽  
Phenol Formaldehyde ◽  
Phenol Formaldehyde Resin ◽  
Formaldehyde Resin ◽  
Shock Resistance

Phenolic formaldehyde (resole) resin was used at a different weight (10%, 20%, 30%, 40%), with epoxy resins at varying percentages (90%, 80%, 70%, 60%) at 20 C °. In order to study the mechanical properties (which including: Tensile strength, hardness and shock resistance), for the purpose of analysis and comparison with the mechanical properties of alloys, and the selected part for the purpose of replacing the alloy with the composite materials to reduce weight and improve mechanical properties. The results indicate improved properties with increased epoxy resins due to increased bonding between components.

Epoxy Resin Embedment

1968 ◽  
Vol 26 ◽  
pp. 100-101
Author(s):  
J. G. Adams ◽  
M. M. Campbell ◽  
H. Thomas ◽  
J. J. Ghldonl
Keyword(s):  
Electron Microscopy ◽  
Electron Beam ◽  
Epoxy Resin ◽  
Light Microscope ◽  
Epoxy Resins ◽  
Image Contrast ◽  
Tissue Preservation ◽  
Resin System ◽  
Excellent Quality

Since the introduction of epoxy resins as embedding material for electron microscopy, the list of new formulations and variations of widely accepted mixtures has grown rapidly. Described here is a resin system utilizing Maraglas 655, Dow D.E.R. 732, DDSA, and BDMA, which is a variation of the mixtures of Lockwood and Erlandson. In the development of the mixture, the Maraglas and the Dow resins were tested in 3 different volumetric proportions, 6:4, 7:3, and 8:2. Cutting qualities and characteristics of stability in the electron beam and image contrast were evaluated for these epoxy mixtures with anhydride (DDSA) to epoxy ratios of 0.4, 0.55, and 0.7. Each mixture was polymerized overnight at 60°C with 2% and 3% BDMA.Although the differences among the test resins were slight in terms of cutting ease, general tissue preservation, and stability in the beam, the 7:3 Maraglas to D.E.R. 732 ratio at an anhydride to epoxy ratio of 0.55 polymerized with 3% BDMA proved to be most consistent. The resulting plastic is relatively hard and somewhat brittle which necessitates trimming and facing the block slowly and cautiously to avoid chipping. Sections up to about 2 microns in thickness can be cut and stained with any of several light microscope stains and excellent quality light photomicrographs can be taken of such sections (Fig. 1).

scholarly journals An Effective Method for Preparation of Liquid Phosphoric Anhydride and Its Application in Flame Retardant Epoxy Resin

Materials ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2205
Author(s):  
Qian Li ◽  
Yujie Li ◽  
Yifan Chen ◽  
Qiang Wu ◽  
Siqun Wang
Keyword(s):  
Flame Retardant ◽  
Epoxy Resin ◽  
Epoxy Resins ◽  
Oxygen Index ◽  
Decomposition Temperature ◽  
Ease Of Use ◽  
Limiting Oxygen Index ◽  
Good Thermal Stability ◽  
Low Viscosity ◽  
The Impact

A novel liquid phosphorous-containing flame retardant anhydride (LPFA) with low viscosity was synthesized from 9,10-dihydro-9-oxa-10-phosphaphenanthrene-10-oxide (DOPO) and methyl tetrahydrophthalic anhydride (MeTHPA) and further cured with bisphenol-A epoxy resin E-51 for the preparation of the flame retardant epoxy resins. Both Fourier transform infrared spectroscopy (FT-IR), mass spectrometry (MS) and nuclear magnetic resonance (NMR) measurements revealed the successful incorporation of DOPO on the molecular chains of MeTHPA through chemical reaction. The oxygen index analysis showed that the LPFA-cured epoxy resin exhibited excellent flame retardant performance, and the corresponding limiting oxygen index (LOI) value could reach 31.2%. The UL-94V-0 rating was achieved for the flame retardant epoxy resin with the phosphorus content of 2.7%. With the addition of LPFA, the impact strength of the cured epoxy resins remained almost unchanged, but the flexural strength gradually increased. Meanwhile, all the epoxy resins showed good thermal stability. The glass transition temperature (Tg) and thermal decomposition temperature (Td) of epoxy resin cured by LPFA decreased slightly compared with that of MeTHPA-cured epoxy resin. Based on such excellent flame retardancy, low viscosity at room temperature and ease of use, LPFA showed potential as an appropriate curing agent in the field of electrical insulation materials.

Thermal Stabilities and the Thermal Degradation Kinetics Study of the Flame Retardant Epoxy Resins

2014 ◽  
Vol 1053 ◽  
pp. 263-267 ◽  
Author(s):  
Xiu Juan Tian
Keyword(s):  
Thermal Stability ◽  
Thermal Degradation ◽  
Flame Retardant ◽  
Epoxy Resin ◽  
Epoxy Resins ◽  
Degradation Kinetics ◽  
Thermal Degradation Kinetics ◽  
Thermal Stabilities ◽  
Degradation Kinetic ◽  
Modified Epoxy

Thermal stability and thermal degradation kinetics of epoxy resins with 2-(Diphenylphosphinyl)-1, 4-benzenediol were investegated by thermogravimetric analysis (TGA) at different heating rates of 5 K/min, 10 K/min, 20 K/min and 40 K/min. The thermal degradation kinetic mechanism and models of the modified epoxy resins were determined by Coast Redfern method.The results showed that epoxy resins modified with the flame retardant had more thermal stability than pure epoxy resin. The solid-state decomposition mechanism of epoxy resin and the modified epoxy resin corresponded to the controlled decelerating ځ˽̈́˰̵̳͂͆ͅ˼˰̴̱̾˰̸̵̈́˰̵̸̳̱̹̽̾̓̽˰̶̳̹̾̈́̿̾̓ͅ˰̶˸ځ˹˰̵̵͇͂˰̃˸́˽ځ˹2/3. The introduction of phosphorus-containing flame retardant reduced thermal degradation rate of epoxy resins in the primary stage, and promote the formation of carbon layer.

scholarly journals A novel h-BN–RGO hybrids for epoxy resin composites achieving enhanced high thermal conductivity and energy density

RSC Advances ◽  
2017 ◽  
Vol 7 (38) ◽  
pp. 23355-23362 ◽  
Author(s):  
Tao Huang ◽  
Xiaoliang Zeng ◽  
Yimin Yao ◽  
Rong Sun ◽  
Fanling Meng ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
Composite Materials ◽  
Energy Density ◽  
Epoxy Resin ◽  
High Thermal Conductivity ◽  
Resin Composites ◽  
Epoxy Resin Composites ◽  
Significant Attention

In recent decades, significant attention has been focused on developing composite materials with high thermal conductivity utilizing h-BN, which has outstanding thermal conductivity.

Ozone Resistance of Vulcanizates Based on XNB Rubber

2021 ◽  
Vol 410 ◽  
pp. 686-691
Author(s):  
Evgeniy S. Bochkarev ◽  
Dmitriy S. Vostrikov ◽  
Oleg O. Tuzhikov
Keyword(s):  
Epoxy Resin ◽  
Magnesium Oxide ◽  
Polyvinyl Chloride ◽  
Flow Rate ◽  
Epoxy Resins ◽  
Butadiene Rubber ◽  
Express Method ◽  
Elastomeric Materials ◽  
Main Period ◽  
Ozone Resistance

The paper represents ozone resistance of rubbers based on carboxylated nitrile butadiene rubber cured with epoxy resins and magnesium oxide. Ozone resistance was investigated using the express-method at a flow rate of the ozone-air mixture of 9 l/h and ozone content of 9 mg/l. In the method used, the “time to cracking start” indicator was taken as the basic indicator of ozone resistance. The second indicator characterizing the ozone resistance of elastomeric materials was the "rate of destruction" in the main period of destruction. There has been evaluated the effect of dissolved polyvinyl chloride in epoxy resin ED-20 on the properties of vulcanizates. There has been investigated the Increase in destruction time under the action of ozone.

scholarly journals THE EFFECT OF COCONUT COIR FIBER POWDER CONTENT AND HARDENER WEIGHT FRACTIONS ON MECHANICAL PROPERTIES OF AN EPR-174 EPOXY RESIN COMPOSITE

SINERGI ◽  
2021 ◽  
Vol 25 (3) ◽  
pp. 361
Author(s):  
Muhamad Fitri ◽  
Shahruddin Mahzan ◽  
Imam Hidayat ◽  
Nurato Nurato
Keyword(s):  
Mechanical Properties ◽  
Shear Strength ◽  
Composite Materials ◽  
Impact Strength ◽  
Epoxy Resin ◽  
Resin Composite ◽  
Weight Fraction ◽  
Resin Matrix ◽  
Powder Content ◽  
Made In

The development of composite materials is increasingly widespread, which require superior mechanical properties. From many studies, it is found that the mechanical properties of composite materials are influenced by various factors, including the reinforcement content, both in the form of fibers and particle powder. However, those studies have not investigated the effect of the hardener weight fraction on the mechanical properties of resin composite materials. Even though its function as a hardener is likely to affect its mechanical properties, it might obtain the optimum composition of the reinforcing content and hardener fraction to get the specific mechanical properties. This study examines the effect of hardener weight fraction combined with fiber powder content on mechanical properties of EPR-174 epoxy resin matrix composite and determines the optimum of Them. The research was conducted by testing a sample of composite matrix resin material reinforced with coconut fiber powder. The Powder content was made in 3 levels, i.e.: 6%, 8%, and 10%. While the hardener fraction of resin was made in 3 levels, i.e.: 0.4, 0.5, and 0.6. The test results showed that pure resin had the lowest impact strength of 1.37 kJ/m2. The specimen with a fiber powder content of 6% has the highest impact strength i.e.: 4.92 kJ/m2. The hardener fraction of 0.5 has the highest impact strength i.e.: 4.55 kJ/m2. The fiber powder content of 8% produced the highest shear strength i.e.: 1.00 MPa. Meanwhile, the hardener fraction of 0.6 has the highest shear strength i.e.: 2.03 MPa.

scholarly journals Gas Turbine Installation and Foundation Repair With Epoxy Resins

1983 ◽  
Author(s):  
J. Murray Wilson
Keyword(s):  
Epoxy Resin ◽  
Gas Turbine ◽  
Thermal Insulation ◽  
Epoxy Resins ◽  
Cement Grouts ◽  
Turbine Installation ◽  
Interface Designs

Epoxy resins are not just replacements for concrete and cement grouts, they offer the opportunity for completely new foundation/gas turbine interface designs. As a substitute for steel chocks, epoxy resin ones give perfect fit, high holding force and good thermal insulation, while eliminating the need for soleplates or rails.

Sign in / Sign up

Export Citation Format

Share Document