scholarly journals Head injury of Vietnamese pedestrian in crash accident with SUV using numerical simulation

2021 ◽  
Vol 3 (SI2) ◽  
pp. first
Author(s):  
Lý Hùng Anh ◽  
Dinh Bao Nguyen ◽  
Anh Huy Nguyen
Keyword(s):  
Experimental Data ◽  
Finite Element ◽  
Automobile Industry ◽  
Head Injuries ◽  
Crash Test ◽  
Crash Simulation ◽  
Standard Criterion ◽  
Hybrid Iii ◽  
The Usa ◽  
Simulation Results

Crash test simulation using finite-element method is more and more popular in the automobile industry because of its feasibility and cost saving. The majority of finite element dummy models used in crash simulation are built based on anthropometrical and biomechanical data of the USA and European bodies. Thus, it is necessary to develop a scaling algorithm to scale a reference dummy size into a desired one without rebuilding the entire model. In this paper, the Hybrid III dummy model provided by LS-DYNA software is scaled to suit Vietnamese biomechanical characteristics. Then a standard criterion for head injuries called HIC is introduced. In addition, the Hybrid III dummy model is validated by comparing experimental data with simulation results obtained from computer model.

scholarly journals Methodology for scaling finite element dummy and validation of a Hybrid III dummy model in crashworthiness simulation

2019 ◽  
Vol 2 (SI2) ◽  
pp. SI105-SI113
Author(s):  
Lý Hùng Anh ◽  
Dinh Bao Nguyen ◽  
Anh Huy Nguyen
Keyword(s):  
Numerical Simulation ◽  
Finite Element ◽  
Head Injury ◽  
Automobile Industry ◽  
Real Life ◽  
Crash Test ◽  
Brain Concussion ◽  
Head Injury Criterion ◽  
Hybrid Iii ◽  
Pedestrian Crashes

For study of car-pedestrian crashes, it is two common methods that can be employed: conducting crash tests with mechanical dummies and simulating car crashes on computer. The former is a traditional way and gives good results compared with real life car impact; however, its disadvantage is very expensive test equipment and generally more time-consuming than the latter because after every crash test, experimental vehicles as well as dummies need repairing to be ready for the next experiments. Therefore, crash test simulation using finite-element method is more and more popular in the automobile industry because of its feasibility and cost saving. The majority of finite element dummy models used in crash simulation. Particularly, it is popular to use Hybrid III 50th dummy model which is built based on fiftieth percentile male (equal in height and weight of the average North American). Thus, it is necessary to develop a scaling algorithm to scale a reference dummy size into a desired one without rebuilding the entire model. In this paper, the Hybrid III dummy model provided by LS-DYNA software is scaled to suit Vietnamese biomechanical characteristics. Scaling algorithm comprises dummy geometry, inertial properties and joint properties is utilized. In order to estimate level of head injury – brain concussion by using numerical simulation, the correlation between Head Injury Criterion (HIC) and Abbreviated Injury Scale (AIS) is introduced. In addition, the Hybrid III dummy model in crashworthiness simulation is presented in key frame picture. Numerical simulation approach is validated by comparing results of head acceleration and HIC obtain from this study with experimental data and numerical simulation results in other publication

scholarly journals Investigation of the Thickness Differential on the Formability of Aluminum Tailor Welded Blanks

Metals ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 875
Author(s):  
Jie Wu ◽  
Yuri Hovanski ◽  
Michael Miles
Keyword(s):  
Experimental Data ◽  
Finite Element ◽  
Numerical Model ◽  
Plastic Strain ◽  
Finite Element Model ◽  
Equivalent Plastic Strain ◽  
Element Model ◽  
Dome Height ◽  
Tailor Welded Blanks ◽  
Simulation Results

A finite element model is proposed to investigate the effect of thickness differential on Limiting Dome Height (LDH) testing of aluminum tailor-welded blanks. The numerical model is validated via comparison of the equivalent plastic strain and displacement distribution between the simulation results and the experimental data. The normalized equivalent plastic strain and normalized LDH values are proposed as a means of quantifying the influence of thickness differential for a variety of different ratios. Increasing thickness differential was found to decrease the normalized equivalent plastic strain and normalized LDH values, this providing an evaluation of blank formability.

scholarly journals Repeatability of Full-Scale Crash Tests and Criteria for Validating Simulation Results

1996 ◽  
Vol 1528 (1) ◽  
pp. 155-160 ◽  
Author(s):  
Malcolm H. Ray
Keyword(s):  
Finite Element ◽  
Full Scale ◽  
Crash Test ◽  
Test Results ◽  
Finite Element Analyses ◽  
Element Analysis ◽  
Acceleration Time Histories ◽  
Time Histories ◽  
Simulation Results ◽  
Crash Tests

A method of comparing two acceleration time histories to determine whether they describe similar physical events is described. The method can be used to assess the repeatability of full-scale crash tests and it can also be used as a criterion for assessing how well a finite-element analysis of a collision event simulates a corresponding full-scale crash test. The method is used to compare a series of six identical crash tests and then is used to compare several finite-element analyses with full-scale crash test results.

The Finite Element Analysis of New Forged Coupler Knuckle

2013 ◽  
Vol 367 ◽  
pp. 122-125
Author(s):  
Guang Xin Wang ◽  
Xiang Shun Bu ◽  
Lin Jie Li ◽  
Li Li Zhu
Keyword(s):  
Experimental Data ◽  
Finite Element ◽  
Direct Relationship ◽  
Element Analysis ◽  
Compression Load ◽  
The Finite Element Analysis ◽  
Simulation Results ◽  
Element Technique ◽  
Working Situation ◽  
Made In

As one of the most important load-bearing parts, coupler knuckle has a direct relationship with the safety in operation and reliability of the freight trains. A new forged coupler knuckle is made in order to meet the challenge to export ore train to Australia. Using the finite element technique, the stress characteristics of forged coupler knuckle under 1225kN load in tension and 1500kN compression load are evaluated. Simplify the load and boundary condition depend on the real working situation, the numerical simulation results coincide with experimental data.

Distortion Simulation of Unsymmetrical Composite Laminates Using the Finite Element Analysis Method

2007 ◽  
Vol 546-549 ◽  
pp. 1563-1566
Author(s):  
Min Li ◽  
Bao Yan Zhang ◽  
Xiang Bao Chen
Keyword(s):  
Experimental Data ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Composite Laminates ◽  
Shell Element ◽  
Element Analysis ◽  
Unsymmetric Laminates ◽  
The Finite Element Analysis ◽  
Simulation Results ◽  
The Difference

Unsymmetric composite laminates were benefit to reducing the structure weight of some aircrafts. However, the cured unsymmetric laminates showed distortion at room temperature. Therefore, predicting the deformation before using the unsymmetrical composite is very important. In this study an attempt was made to predict the shapes of some unsymmetric cross-ply laminates using the finite element analysis (FEA). The bilinear shell-element was adopted in the process. Then the simulation results were compared with the experimental data. The studies we had performed showed that the theoretical calculation agreed well with the experimental results, the predicted shapes were similar to the real laminates, and the difference between the calculated maximum deflections and the experimental data were less than 5%. Hence the FEA method was suitable for predicting the warpage of unsymmetric laminates. The error analysis showed that the simulation results were very sensitive to the lamina thickness, 2 α and (T.

Variable Thickness Rolling - A New Process for Rolled Profile Strips

2018 ◽  
Vol 792 ◽  
pp. 47-52
Author(s):  
Xiao Gong Wang ◽  
Xiang Hua Liu
Keyword(s):  
Experimental Data ◽  
Finite Element ◽  
Cross Sections ◽  
Variable Thickness ◽  
Industrial Development ◽  
Element Model ◽  
Light Weight ◽  
New Process ◽  
Roll System ◽  
Simulation Results

As a result of more requirements for improving natural environment and economic environment, the manufacturing of light weight components is becoming increasingly vital in industrial development. Variable thickness rolling (VTR)-a new process for rolled profile strips (RPS) is proposed in this paper. This so-called “variable thickness rolling” is based on the utilization of a special roll system that causes the material to flow in latitudinal direction. The rolled profile strips with defined cross-sections are obtained by this process. The elastic-plastic finite element model is established to analyze the forming principle. The simulation results agree with experimental data on the whole.

scholarly journals Finite Element Model Validation of the Hybrid-III Rail Safety (H3-RS) Anthropomorphic Test Device (ATD)

2018 ◽  
Author(s):  
Shaun Eshraghi ◽  
Kristine Severson ◽  
David Hynd ◽  
A. Benjamin Perlman
Keyword(s):  
Finite Element ◽  
Public Transportation ◽  
Crash Test ◽  
Fe Model ◽  
Test Device ◽  
Sled Test ◽  
Impact Tests ◽  
Hybrid Iii ◽  
Pendulum Impact ◽  
Vertical Impact

The Hybrid-III Rail Safety (H3-RS) anthropomorphic test device (ATD), also known as a crash test dummy, was developed by the Rail Safety and Standards Board (RSSB), DeltaRail (now Resonate Group Ltd.), and the Transport Research Laboratory (TRL) in the United Kingdom between 2002 and 2005 for passenger rail safety applications [1]. The H3-RS is a modification of the standard Hybrid-III 50th percentile male (H3-50M) ATD with additional features in the chest and abdomen to increase its biofidelity and eight sensors to measure deflection. The H3-RS features bilateral (left and right) deflection sensors in the upper and lower chest and in the upper and lower abdomen; whereas, the standard H3-50M only features a single unilateral (center) deflection sensor in the chest with no deflection sensors located in the abdomen. Additional H3-RS research was performed by the Volpe National Transportation Systems Center (Volpe Center) under the direction of the U.S. Department of Transportation, Federal Railroad Administration (FRA) Office of Research, Development, and Technology. The Volpe Center contracted with TRL to conduct a series of dynamic pendulum impact tests [2]. The goal of testing the abdomen response of the H3-RS ATD was to develop data to refine an abdomen design that produces biofidelic and repeatable results under various impact conditions with respect to impactor geometry, vertical impact height, and velocity. In this study, the abdominal response of the H3-RS finite element (FE) model that TRL developed is validated using the results from pendulum impact tests [2]. Results from the pendulum impact tests and corresponding H3-RS FE simulations are compared using the longitudinal relative deflection measurements from the internal sensors in the chest and abdomen as well as the longitudinal accelerometer readings from the impactor. The abdominal response of the H3-RS FE model correlated well with the physical ATD as the impactor geometry, vertical impact height, and velocity were changed. There were limitations with lumbar positioning of the H3-RS FE model as well as the material definition for the relaxation rate of the foam in the abdomen that can be improved in future work. The main goal of validating the abdominal response of the dummy model is to enable its use in assessing injury potential in dynamic sled testing of crashworthy workstation tables, the results of which are presented in a companion paper [3]. The authors used the model of the H3-RS ATD to study the 8G sled test specified in the American Public Transportation Association (APTA) workstation table safety standard [4]. The 8G sled test is intended to simulate the longitudinal crash accleration in a severe train-to-train collision involving U.S. passenger equipment. Analyses of the dynamic sled test are useful for studying the sensitivity of the sled test to factors such as table height, table force-crush behavior, seat pitch, etc., which help to inform discussions on revisions to the test requirements eventually leading to safer seating environments for passengers.

Crashworthiness of a Truck Cabin using Finite Element Simulation

2017 ◽  
Vol 8 (4) ◽  
Author(s):  
N.K. Mishra ◽  
S.K. Pradhan.
Keyword(s):  
Finite Element ◽  
Rigid Wall ◽  
Vehicle Body ◽  
Design Parameters ◽  
Crash Test ◽  
Small Scale ◽  
Scale Production ◽  
Crash Analysis ◽  
Structural Behaviour ◽  
Crash Simulation

A crash test is a form of destructive testing in order to ensure safe design in case of an impact or collision. These impact tests are carried out to understand a components structural behaviour and its response under different collision conditions. But it is not always economical to destroy a specimen to ensure its safety, especially in case of small scale production. Moreover actual crash testing in different conditions requires high resources and time. Crash simulation is very popular now a days because it is a virtual representation of a destructive crash test of a vehicle using a computer simulation in order to examine the level of safety of the vehicle and its occupants in different conditions like collision velocity, collision direction, colliding object, material and number of component of colliding object etc and hence saves the time and cost. Data obtained from a crash simulation indicate the capability of the vehicle body to protect the vehicle occupants during a collision against injury. In this study a FE crash analysis of commercial truck cabin in two different cases (Bare cabin and loaded cabin) using Finite Element Approach (FEA) is focused. Crash analysis of truck cab is performed using FEA in order to predict the design parameters for minimization harm to the occupants of the vehicle. A bare truck cabin and a rigid wall were used to simulate crash conditions with different crashing velocity and impact angles. CATIA V5R20 CAD software is used for the modeling of the selected cabin components followed by FE meshing through Hypermesh and then analysis is done using LS-DYNA by setting the boundary conditions, material properties etc. appropriately.

scholarly journals Numerical Simulation and Experimental Study on the Drilling Process of 7075-t6 Aerospace Aluminum Alloy

Materials ◽  
2021 ◽  
Vol 14 (3) ◽  
pp. 553
Author(s):  
Haitao Luo ◽  
Jia Fu ◽  
Tingke Wu ◽  
Ning Chen ◽  
Huadong Li
Keyword(s):  
Experimental Data ◽  
Numerical Simulation ◽  
Finite Element ◽  
Finite Element Model ◽  
Axial Force ◽  
Element Model ◽  
Drilling Process ◽  
Feed Speed ◽  
Rotating Speed ◽  
Simulation Results

A finite element model for setting drilling conditions is established. The effect of feed speed and spindle speed on the drilling process was studied. In the test phase, drilling tests were conducted using three different feed speeds (60, 100, and 140 mm/min) and three different spindle speeds (800, 1000, and 1200 rpm). The correctness of the finite element model was verified by comparing the experimental and numerical simulation data. The results show that the axial force and torque increase significantly with the increase of feed speed, while the axial force and torque increase less as the spindle speed increases. The numerical simulation results show that the temperature of the cutting edge increases as the feed speed increases. Increasing the rotating speed increases the formation of chip curl. When the working conditions are high rotating speed and low feed, the tool wear is reduced, and the machining quality is better. The numerical simulation results obtained for the chip forming effect are similar to the experimental data. In addition, the simulation results show the generation of burrs. A comparison of the finite element simulation and experimental data leads to an in-depth understanding of the drilling process and ability to optimize subsequent drilling parameters, which provide reliable process parameters and technical guarantees for the successful implementation of drilling technology for space suspended ball structures.

Sign in / Sign up

Export Citation Format

Share Document