scholarly journals STUDY ON MECHANICAL PROPERTIES AND MICROSTRUCTURE OF 42CrMo4/NANOS-BA® HIGH-STRENGTH CLAD PLATES AFTER THE PROCESS OF HOT ROLLING AND TWO-STAGE HEAT TREATMENT WITH ISOTHERMAL TRANSFORMATION

2021 ◽  
Vol 73 (1) ◽  
pp. 22-31
Author(s):  
Bartłomiej WALNIK ◽  
Dariusz Woźniak ◽  
Aleksandra NIESZPOREK ◽  
Mariusz ADAMCZYK
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Hot Rolling ◽  
High Strength ◽  
Isothermal Transformation ◽  
Two Stage ◽  
Physical Experiments ◽  
Microstructure Examination ◽  
Steel Grades ◽  
Stage Heat Treatment

The aim of the study was to develop a technology for welding non-weldable 42CrMo4 and NANOS-BA® steel grades in the process of hot rolling and two-stage heat treatment. As a result of physical experiments carried out in a line for semi-industrial simulation of the production of metals and their alloys (LPS) and additional heat treatment, a durable combination of 42CrMo4 and NANOS-BA® steels with high mechanical properties was obtained, including: Rp0.2 = 1036 MPa, Rm = 1504 MPa and A = 10.9%, without microscopically visible cracks and other discontinuities in the joined surface. The quality of the 42CrMo4/NANOS-BA® clad plates produced in this way was assessed on the basis of microstructure examination as well as bending, shear and tensile strength tests.

Microstructure and Tensile Properties of TRIP-Aided Steel Sheet Subjected to Hot-Rolling and Austempering

2021 ◽  
Vol 1016 ◽  
pp. 732-737
Author(s):  
Junya Kobayashi ◽  
Hiroto Sawayama ◽  
Naoya Kakefuda ◽  
Goroh Itoh ◽  
Shigeru Kuraoto ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Hot Rolling ◽  
Manufacturing Process ◽  
Retained Austenite ◽  
Volume Fraction ◽  
Isothermal Holding ◽  
High Strength ◽  
Isothermal Transformation ◽  
Transformation Process ◽  
Steel Sheets

Various high strength steel sheets for weight reduction and safety improvement of vehicles have been developed. TRIP-aided steel with transformation induced plasticity of the retained austenite has high strength and ductility. Conventional TRIP-aided steels are subjected to austempering process after austenitizing. Generally, elongation and formability of TRIP-aided steel are improved by finely dispersed retained austenite in BCC phase matrix. The finely dispersed retained austenite and grain refinement of TRIP-aided steel can be achieved by hot rolling with heat treatment. Therefore, the improvement of mechanical properties of TRIP-aided steel is expected from the manufacturing process with hot rolling and then isothermal transformation process. In this study, thermomechanical heat treatment is performed by combining hot rolling and isothermal holding as the manufacturing process of TRIP-aided steel sheets. The complex phase matrix is obtained by hot rolling and then isothermal holding. Although the hardness of the hot rolled and isothermal held TRIP-aided steel is decreased, the volume fraction of retained austenite is increased.

scholarly journals The Effect Of Carbon Concentration On The Retained Austenite Content And The Mechanical Properties Of TRIP Steel Wire Rod Obtained From The Stelmor Controlled Cooling Line

2015 ◽  
Vol 60 (3) ◽  
pp. 1949-1952
Author(s):  
Z. Muskalski ◽  
S. Wiewiórowska
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Carbon Concentration ◽  
Retained Austenite ◽  
Steel Wire ◽  
Controlled Cooling ◽  
Two Stage ◽  
Wire Rod ◽  
Austenite Content ◽  
Stage Heat Treatment

Abstract The austenite content of the multiphase TRIP-structure steels depends, inter alia, on the carbon concentration and the properly selected parameters of the two-stage heat treatment. Under the existing industrial conditions, it is possible to (approximately) reproduce approximately the optimal parameters of the two-stage wire rod heat treatment via the controlled wire rod cooling from the end temperature of rolling on the Stelmor line. The investigation of the retained austenite content of TRIP wire rods with a varying carbon concentration, produced under industrial conditions, has been discussed and the effect of the multiphase structure of these wire rods on their mechanical properties has been determined in the paper.

scholarly journals The Effect of a Two-Stage Heat-Treatment on the Microstructural and Mechanical Properties of a Maraging Steel

Materials ◽  
2017 ◽  
Vol 10 (12) ◽  
pp. 1346 ◽  
Author(s):  
Thomas Simm ◽  
Lin Sun ◽  
Deri Galvin ◽  
Paul Hill ◽  
Martin Rawson ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Maraging Steel ◽  
Two Stage ◽  
Stage Heat Treatment

UNS A97075

Alloy Digest ◽  
1986 ◽  
Vol 35 (7) ◽  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Aluminum Alloy ◽  
High Strength ◽  
Heat Treating ◽  
Good Resistance ◽  
Temperature Performance ◽  
Structural Applications ◽  
Structural Parts ◽  
Very High

Abstract UNS No. A97075 is a wrought precipitation-hardenable aluminum alloy. It has excellent mechanical properties, workability and response to heat treatment and refrigeration. Its typical uses comprise aircraft structural parts and other highly stressed structural applications where very high strength and good resistance to corrosion are required. This datasheet provides information on composition, physical properties, hardness, elasticity, tensile properties, and shear strength as well as fatigue. It also includes information on low temperature performance as well as forming, heat treating, and machining. Filing Code: Al-269. Producer or source: Various aluminum companies.

scholarly journals Grain Size Evolution and Mechanical Properties of Nb, V–Nb, and Ti–Nb Boron Type S1100QL Steels

Metals ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 492
Author(s):  
Jan Foder ◽  
Jaka Burja ◽  
Grega Klančnik
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Grain Size ◽  
Hot Forging ◽  
Size Control ◽  
High Strength ◽  
Fatigue Properties ◽  
Titanium Addition ◽  
Austenite Grain Size ◽  
Size Evolution

Titanium additions are often used for boron factor and primary austenite grain size control in boron high- and ultra-high-strength alloys. Due to the risk of formation of coarse TiN during solidification the addition of titanium is limited in respect to nitrogen. The risk of coarse nitrides working as non-metallic inclusions formed in the last solidification front can degrade fatigue properties and weldability of the final product. In the presented study three microalloying systems with minor additions were tested, two without any titanium addition, to evaluate grain size evolution and mechanical properties with pre-defined as-cast, hot forging, hot rolling, and off-line heat-treatment strategy to meet demands for S1100QL steel. Microstructure evolution from hot-forged to final martensitic microstructure was observed, continuous cooling transformation diagrams of non-deformed austenite were constructed for off-line heat treatment, and the mechanical properties of Nb and V–Nb were compared to Ti–Nb microalloying system with a limited titanium addition. Using the parameters in the laboratory environment all three micro-alloying systems can provide needed mechanical properties, especially the Ti–Nb system can be successfully replaced with V–Nb having the highest response in tensile properties and still obtaining satisfying toughness of 27 J at –40 °C using Charpy V-notch samples.

scholarly journals Overview of HSS Steel Grades Development and Study of Reheating Condition Effects on Austenite Grain Size Changes

Materials ◽  
2021 ◽  
Vol 14 (8) ◽  
pp. 1988
Author(s):  
Tibor Kvackaj ◽  
Jana Bidulská ◽  
Róbert Bidulský
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
High Strength Steel ◽  
Single Phase ◽  
Hsla Steel ◽  
High Strength ◽  
Strength Properties ◽  
Austenite Grain Size ◽  
Austenite Grain ◽  
Steel Grades

This review paper concerns the development of the chemical compositions and controlled processes of rolling and cooling steels to increase their mechanical properties and reduce weight and production costs. The paper analyzes the basic differences among high-strength steel (HSS), advanced high-strength steel (AHSS) and ultra-high-strength steel (UHSS) depending on differences in their final microstructural components, chemical composition, alloying elements and strengthening contributions to determine strength and mechanical properties. HSS is characterized by a final single-phase structure with reduced perlite content, while AHSS has a final structure of two-phase to multiphase. UHSS is characterized by a single-phase or multiphase structure. The yield strength of the steels have the following value intervals: HSS, 180–550 MPa; AHSS, 260–900 MPa; UHSS, 600–960 MPa. In addition to strength properties, the ductility of these steel grades is also an important parameter. AHSS steel has the best ductility, followed by HSS and UHSS. Within the HSS steel group, high-strength low-alloy (HSLA) steel represents a special subgroup characterized by the use of microalloying elements for special strength and plastic properties. An important parameter determining the strength properties of these steels is the grain-size diameter of the final structure, which depends on the processing conditions of the previous austenitic structure. The influence of reheating temperatures (TReh) and the holding time at the reheating temperature (tReh) of C–Mn–Nb–V HSLA steel was investigated in detail. Mathematical equations describing changes in the diameter of austenite grain size (dγ), depending on reheating temperature and holding time, were derived by the authors. The coordinates of the point where normal grain growth turned abnormal was determined. These coordinates for testing steel are the reheating conditions TReh = 1060 °C, tReh = 1800 s at the diameter of austenite grain size dγ = 100 μm.

scholarly journals Achievement of High Strength and Ductility in Al–Si–Cu–Mg Alloys by Intermediate Phase Optimization in As-Cast and Heat Treatment Conditions

Materials ◽  
2020 ◽  
Vol 13 (3) ◽  
pp. 647 ◽  
Author(s):  
Bingrong Zhang ◽  
Lingkun Zhang ◽  
Zhiming Wang ◽  
Anjiang Gao
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Intermediate Phase ◽  
High Strength ◽  
Mg Alloys ◽  
Artificial Ageing ◽  
Treatment Conditions ◽  
Eutectic Si

In order to obtain high-strength and high-ductility Al–Si–Cu–Mg alloys, the present research is focused on optimizing the composition of soluble phases, the structure and morphology of insoluble phases, and artificial ageing processes. The results show that the best matches, 0.4 wt% Mg and 1.2 wt% Cu in the Al–9Si alloy, avoided the toxic effect of the blocky Al2Cu on the mechanical properties of the alloy. The addition of 0.6 wt% Zn modified the morphology of eutectic Si from coarse particles to fine fibrous particles and the texture of Fe-rich phases from acicular β-Fe to blocky π-Fe in the Al–9Si–1.2Cu–0.4Mg-based alloy. With the optimization of the heat treatment parameters, the spherical eutectic Si and the fully fused β-Fe dramatically improved the ultimate tensile strength and elongation to fracture. Compared with the Al–9Si–1.2Cu–0.4Mg-based alloy, the 0.6 wt% Zn modified alloy not only increased the ultimate tensile strength and elongation to fracture of peak ageing but also reduced the time of peak ageing. The following improved combination of higher tensile strength and higher elongation was achieved for 0.6 wt% Zn modified alloy by double-stage ageing: 100 °C × 3 h + 180 °C × 7 h, with mechanical properties of ultimate tensile strength (UTS) of ~371 MPa, yield strength (YS) of ~291 MPa, and elongation to fracture (E%) of ~5.6%.

Sign in / Sign up

Export Citation Format

Share Document