scholarly journals Length Effect on Load Bearing Capacities of Friction Rock Bolts

2019 ◽  
Author(s):  
Eren Komurlu ◽  
Serhat Demir
Keyword(s):  
Numerical Modelling ◽  
Bearing Capacity ◽  
Experimental Studies ◽  
Rock Bolt ◽  
Rock Bolts ◽  
Length Effect ◽  
Load Bearing Capacity ◽  
Load Bearing ◽  
Pull Out ◽  
Modelling Study

Change in the load bearing capacity of the split set type friction rock bolts with variations of bolt lengths was investigated within this study. To determine a relation between the load bearing capacity and bolt length parameters, different friction bolt models with various lengths were analyzed with a numerical modelling study. In addition, a series of pull-out tests was carried out to evaluate the load bearing capacities of the split set type friction rock bolts with different lengths. The load bearing capacity of the bolts was found to decreasingly increase with the increase in the bolt length. As an outcome of this study, a relation between the load bearing capacity and rock bolt length parameters is suggested in accordance with the results obtained from both numerical and experimental studies.

scholarly journals Investigation of Load Bearing Capacities of Grouted Rock Bolts with New Auxetic Head Designs

2020 ◽  
Author(s):  
Eren Komurlu ◽  
Aysegul Durmus Demir ◽  
Atila Gurhan Celik
Keyword(s):  
Numerical Modelling ◽  
Energy Absorption ◽  
Experimental Studies ◽  
Head Part ◽  
Rock Bolts ◽  
Load Bearing ◽  
Ratio Effect ◽  
Pull Out ◽  
Drill Holes ◽  
Grouted Rock Bolts

Within this study, new bolt heads were designed to be able to expand in drill holes as the load applied on the bolt shank increases. The heads of newly designed rock bolts include a conic part and split rings encircling them. To determine load bearing capacities of new rock bolts with varying angles of the conic parts and expansion properties, a series of deformation controlled pull-out tests were carried out by using bolt samples grouted in rock blocks. In addition to the experimental studies, numerical modelling analyses were performed to better understand the support properties of newly designed rock bolts. Because of a negative Poisson’s ratio effect supplied by the head part expansion with the tension of the shank, new bolt heads are suggested to be defined as auxetic. According to the results of this study, the new head designs significantly improve the load bearing and energy absorption capacities of grouted rock bolts.

Research of the Load Bearing Capacity of Shape-Optimized Metal Inserts Embedded in CFRP under Different Types of Stresses

2017 ◽  
Vol 742 ◽  
pp. 636-643 ◽  
Author(s):  
Florentin Pottmeyer ◽  
Markus Muth ◽  
Kay André Weidenmann
Keyword(s):  
Bearing Capacity ◽  
Residual Strength ◽  
High Speed ◽  
Systematic Research ◽  
Load Bearing Capacity ◽  
Load Bearing ◽  
Temperature Cycles ◽  
Pull Out ◽  
Different Types ◽  
Impact Energies

An efficient implementation of lightweight design is the use of continuous carbon fiber reinforced plastics (CFRP) due to their outstanding specific mechanical properties. Embedded metal elements, so-called inserts, can be used to join metal-based attachments to structural CFRP parts in the context of multi-material design. They differ from other mechanical fasteners and have distinctive benefits. In particular, drilling of the components to be joined can be avoided and, depending on the preforming, fiber continuity can be maintained using such elements. Thus, no local bearing stress is anticipated. Previous work published by the authors [1] dealt with a systematic research of the influence of different types of stresses on the load bearing capacity of welded inserts. This contribution aims at the investigation of the performance of shape-optimized inserts under the same types of loading to compare with the results of the welded inserts serving as a reference. For that purpose, the respective load bearing capacities were evaluated after preinduced damages from impact tests and thermal cycling. In addition, dynamic high-speed tensile tests (pull-out) were conducted under different loading velocities. It is shown that the load bearing capacities increased up to 19% for high velocities (250 mm/s) in comparison to quasi-static loading conditions (1.5 mm/min) showing an obvious strain rate dependency of the CFRP. Quasi-static residual strength measurements under tensile loading identified the influence of the respective preinduced damages of the insert. Influence of the thermal loading condition was evaluated by placing the specimens in a climate chamber and exposing it to various numbers of temperature cycles from-40 °C to +80 °C with a duration time of 1.5 hours each. Here, it turned out that already 10 temperature cycles decreased the quasi-static load bearing capacity up to 31%. According to DIN EN 6038 the specimens were loaded with different impact energies and the residual strength were measured carrying out pull-out tests. It could be shown that the damage tolerance is significantly lower for the shape-optimized insert due to failure-critical delamination. The optimized insert also endured lower impact energies and the influence on the performance was higher.

scholarly journals Analytical modelling of a three-layer wall system of strengthening for large-panel slab buildings by means of bonded anchors

2018 ◽  
Vol 174 ◽  
pp. 04012
Author(s):  
Jerzy K. Szlendak ◽  
Agnieszka Jablonska-Krysiewicz ◽  
Dariusz Tomaszewicz
Keyword(s):  
Bearing Capacity ◽  
Analytical Models ◽  
Simultaneous Action ◽  
Strength Parameters ◽  
Load Bearing Capacity ◽  
Load Bearing ◽  
Pull Out ◽  
Large Panel ◽  
Wall System ◽  
New System

The goal of the article is to elaboration analytical models describing a new system of reinforcing three-layer walls of large-panel buildings with bonded anchors. The use of this type of fasteners that bond the façade texture layer to the structural slab is necessary due to the low durability of previously used suspension elements. Various bonded anchorage systems were considered. The new anchorage systems were designed as two-anchors systems (horizontal anchor and diagonal anchors) and three-anchors systems (horizontal anchor and two diagonal anchors). The inclinations of these anchors are in the range of 30°-60° in relation to the surface of the element. For the above types of reinforcements, analytical models have been developed that take into account the change of strength parameters of the resin and steel from which the anchors were made, the interaction of materials resin-steel and resin-concrete and the effect of the simultaneous action of pull-out and shearing forces. Moreover, was assumed the simultaneous destruction of fasteners two- and three-anchors. The elaborated analytical models will be used to determine the load-bearing capacity of the new connector system, which will allow the elaboration of guidelines for strengthening three-layer walls of largepanel slab buildings.

scholarly journals Numerical Modelling Of The Strengthening Process Of Steel-Concrete Composite Beams

2015 ◽  
Vol 19 (4) ◽  
pp. 99-110 ◽  
Author(s):  
Piotr Szewczyk ◽  
Maciej Szumigała
Keyword(s):  
Numerical Modelling ◽  
Bearing Capacity ◽  
Composite Beam ◽  
Steel Plate ◽  
Composite Beams ◽  
Steel Beam ◽  
Load Bearing Capacity ◽  
Load Bearing ◽  
Main Assumption ◽  
The Cost

Abstract This paper presents the numerical modelling of strengthening a steel-concrete composite beam. The main assumption is that the strengthening is not the effect of the state of a failure of a structure, but it resulted from the need to increase the load-bearing capacity and stiffness of the structure (for example: due to a change in the use of the object). The expected solution is strengthening without the necessity to completely unload the structures (to reduce the scope of works, the cost of modernization and to shorten the time). The problem is presented on the example of a composite beam which was strengthened through welding a steel plate to the lower flange of the steel beam. The paper describes how energy parameters are used to evaluate the efficiency of structures’ strengthening and proposes an appropriate solution.

scholarly journals DETERMINATION OF THE AMOUNT OF ADHESION OF BASALT-PLASTIC REINFORCEMENT TO CONCRETE

2020 ◽  
Vol 8 (3) ◽  
pp. 36-39
Author(s):  
Yulia Kustikova
Keyword(s):  
Bearing Capacity ◽  
Experimental Studies ◽  
Concrete Structures ◽  
Load Bearing Capacity ◽  
Load Bearing

The results of experimental studies and tests of concrete structures with basalt-plastic reinforcement to determine the load-bearing capacity, as well as the mechanism of adhesion of basalt-plastic rods to concrete are considered.

Role of Collagen Content and Architecture in the Load Bearing Capabilities of Tissue-Engineered Cartilage

2011 ◽  
Author(s):  
M. Khoshgoftar ◽  
C. C. van Donkelaar ◽  
K. Ito
Keyword(s):  
Bearing Capacity ◽  
Network Architecture ◽  
Mechanical Performance ◽  
Experimental Studies ◽  
Limiting Factor ◽  
Collagen Network ◽  
Load Bearing Capacity ◽  
Load Bearing ◽  
Native Cartilage ◽  
Engineer Cartilage

A promising treatment for damaged cartilage is to replace it with tissue-engineered (TE) cartilage. However, the insufficient load-bearing capacity of today’s TE cartilage is an important limiting factor in its clinical application. In native cartilage, collagen fibers resist tension and proteoglycans (PG’s) attract water through osmotic pressure and resist its flow, which allows cartilage to withstand high compressive forces. One of the main challenges for tissue engineering of mechanically stable cartilage is therefore to find the cues to create an engineered tissue with an ultrastructure similar to that of native tissue. Currently, it is possible to tissue engineer cartilage with almost native PG content but collagen reaches only 1/4 of the native content [1]. Furthermore, the specific depth dependent arcade-like organization of collagen in native cartilage (i.e. vertical fibers in the deep zone and horizontal fibers in the superficial zone), which is optimized for distributing loads, has not been addressed in TE’d cartilage. However, the relative importance of matrix component content and collagen network architecture to the mechanical performance of TE cartilage is poorly understood, perhaps because this would require substantial effort on time consuming and labor-intensive experimental studies. The aim of this study is to explore if it is sufficient to produce a tissue with abundant proteoglycans and/or collagen, or whether reproducing the specific arcade-like collagen network in the implant is essential to develop sufficient load-bearing capacity, using a numerical approach.

scholarly journals Experimental Investigation and Modelling of the Layered Concrete with Different Concentration of Short Fibers in the Layers

Fibers ◽  
2021 ◽  
Vol 9 (12) ◽  
pp. 76
Author(s):  
Vitalijs Lusis ◽  
Olga Kononova ◽  
Arturs Macanovskis ◽  
Rimvydas Stonys ◽  
Inga Lasenko ◽  
...  
Keyword(s):  
Experimental Data ◽  
Bearing Capacity ◽  
Fracture Process ◽  
Fiber Reinforced Concrete ◽  
Short Fibers ◽  
Steel Fiber Reinforced Concrete ◽  
Load Bearing Capacity ◽  
Fiber Concentration ◽  
Load Bearing ◽  
Pull Out

The use of steel fiber reinforced concrete (SFRC) in structures with high physical-mechanical characteristics allows engineers to reduce the weight and costs of the structures, to simplify the technology of their production, to reduce or completely eliminate the manual labor needed for reinforcement, at the same time increasing reliability and durability. Commonly accepted technology is exploiting randomly distributed in the concrete volume fibers with random each fiber orientation. In structural members subjected to bending, major loads are bearing fibers located close to outer member surfaces. The majority of fibers are slightly loaded. The aim of the present research is to create an SFRC construction with non-homogeneously distributed fibers. We prepared layered SFRC prismatic specimens. Each layer had different amount of short fibers. Specimens were tested by four point bending till the rupture. Material fracture process was modelled based on the single fiber pull-out test results. Modelling results were compared with the experimental curves for beams. Predictions generated by the model were validated by 4PBT of 100 × 100 × 400 mm prisms. Investigation had shown higher load-bearing capacity of layered concrete plates comparing with plate having homogeneously distributed the same amount of fibers. This mechanism is strongly dependent on fiber concentration. A high amount of fibers is leading to new failure mechanisms—pull-out of FRC blocks and decrease of load-bearing capacity. Fracture surface analysis was realized for broken prisms with the goal to analyze fracture process and to improve accuracy of the elaborated model. The general conclusion with regard to modelling results is that the agreement with experimental data is good, numeric modelling results successfully align with the experimental data. Modelling has indicated the existence of additional failure processes besides simple fiber pull-out, which could be expected when fiber concentration exceeds the critical value.

scholarly journals Determination of the load-bearing capacity of «steel-wood» connections of LVL structures under tension

2021 ◽  
Vol 18 (1) ◽  
pp. 60-69
Author(s):  
Quoc Phong Tran ◽  
Keyword(s):  
Bearing Capacity ◽  
Cross Section ◽  
Steel Plate ◽  
Experimental Studies ◽  
Steel Plates ◽  
Load Bearing Capacity ◽  
Load Bearing ◽  
Dowel Connections ◽  
Wooden Structures

The article presents the results of calculation of the load-bearing capacity of connections of LVL structures under tension using cylindrical dowels in trusses and frames. The description of calculation schemes for determining the load-bearing capacity of connections with different location and sizes of steel plates in the connection is given. The influence of steel plate placement on the distribution of forces in the cross-section of samples is investigated. Based on the results of analytical and experimental studies, the load-bearing capacity of dowels during bending is considered, as well as the mechanism of wooden structures` fracture during chipping. A comparative analysis of the effectiveness of different schemes of dowel connections with three steel plates under tension is carried out.

scholarly journals Methods of Calculation the Increased Reinforced Concrete Elements by Carrying Capacity of Slope Sections

2021 ◽  
Vol 1203 (2) ◽  
pp. 022051
Author(s):  
Andrii Mazurak ◽  
Roman Kinasz ◽  
Ivan Kovalyk ◽  
Rostyslav Mazurak ◽  
Vitaliy Kalchenko
Keyword(s):  
Reinforced Concrete ◽  
Bearing Capacity ◽  
Experimental Studies ◽  
Longitudinal Axis ◽  
Load Bearing Capacity ◽  
Load Bearing ◽  
Theoretical Approaches ◽  
Reinforced Beams ◽  
Eurocode 2 ◽  
Concrete Elements

Abstract Reinforcement bending reinforced concrete structures by increasing the cross section and assessing the load-bearing capacity of the inclined section such elements is an urgent problem, as not yet accumulated adequate research data on the stress-strain state such structures in the span, which works on shear and shear bending moment and transverse force. Analyzing the development theories calculation reinforced concrete elements inclined to the longitudinal axis, we can identify many areas, the main approach of which was based on the calculation using the bases of material resistance, and the use of empirical dependencies. Theoretical approaches calculation the European construction magazine RILEM TC, SNiP 2.03.01.-84* are considered, DBN B.2.6-98 2009 (Eurocode 2), US ACI 318-19. Experimental studies reinforced concrete elements to determine the load-bearing capacity inclined sections were performed on the basis of 5 samples reinforced concrete beams, 14 reinforced samples of reinforced concrete and shotcrete a total of 19 pieces in four series. Beams were made of concrete in each series fck = 19.08 MPa; fck = 27.74 MPa; fck = 20.48 MPa; fck = 20.48 MPa, respectively, reinforced samples with concrete fck = 17.95 MPa; fck = 19.5 MPa (shotcrete fck = 31.00 MPa); shotcrete fck = 19.9 MPa; fck = 19.9 MPa. Also for the manufacture and reinforcement beams used flat and U-shaped frames with working longitudinal reinforcement Ø22, Ø16, Ø12, Ø10, Ø6 A400C, and transverse reinforcement Ø6 A240C (step 120 mm). Reinforcement inclined sections of the experimental beams was performed on one, two or three sides, depending on the variant of the sample and the type of frame flat or U-shaped. Investigations of beams were performed according to the static scheme - a beam on two supports, span L=2100 mm. Deformations of concrete and reinforcement in the samples when determining the bearing capacity of inclined sections were measured using microindicators of the clock type, strain gauges. According to the results theoretical and experimental studies the bearing capacity inclined sections to the longitudinal axis, we can see a significant reassessment between the theoretical values inclined sections according to the new DBN B.2.6.-98: 2009 (Eurocode 2) over the actual results obtained during testing samples 53-67% for conventional beams, and 27-50% for reinforced beams. The results US regulations ACI 318-19 showed convergence of results in the range of 2-9% for samples without reinforcement and 1-7% for samples with reinforcement, but the values show the excess of experimental data over theoretical, indicating the impossibility of accurately determining the actual final bearing capacity. The results the calculation obtained by the method of SNiP 2.03.01-84*, both unreinforced and reinforced beams has a satisfactory agreement with the experimental values in the range of 6-10%.

scholarly journals Study on an Innovative Flange Bolted-Welded Connection

2015 ◽  
Vol 9 (1) ◽  
pp. 870-875
Author(s):  
Yufeng Jiao ◽  
Guo Zhao
Keyword(s):  
Bearing Capacity ◽  
Failure Modes ◽  
Experimental Studies ◽  
High Strength ◽  
Bottom Flange ◽  
Load Bearing Capacity ◽  
Load Bearing ◽  
Hybrid Joint ◽  
Welded Connection ◽  
Cyclic Loading Tests

This paper proposes a new type of spliced joint, named flange bolted-welded hybrid joint, which is designed to splice I-shape beam to facilitate the construction of industrialized buildings. The flange, welded with the bottom beam flange as well as the web close to bottom flange, are jointed by high strength bolts. Stiffening plate is welded at top of the flange while downhand welding and high strength friction grip bolts are used for the top beam flange and the beam web, respectively. The connection reduces the construction period and costs. In this paper, monotonic and reversed cyclic loading tests were conducted on three full-scale specimens of this innovative joint to investigate its load-bearing capacity, energy-dissipating capacity and failure modes. The results indicate that the joint has high load-bearing capacity and great ductility. The failure mode is due to the slippage of flange bolts as well as the gap development between the two flange plates. The experimental studies enabled improvement of the design of the connection to be used in moment-resisting steel frame structures.

Sign in / Sign up

Export Citation Format

Share Document