scholarly journals Variation of Mechanical Properties of Polypropylene Composites with the Additives Content: An Empirical Mathematical Modeling Study

2021 ◽  
Vol 13 (2) ◽  
pp. 611-621
Author(s):  
M. Mostafizur Rahman ◽  
Iftekhar Chowdhury ◽  
M. Mastabur Rahman
Keyword(s):  
Mathematical Modeling ◽  
Mechanical Properties ◽  
Tensile Properties ◽  
Rice Husk Ash ◽  
Jute Fiber ◽  
Low Density Polyethylene ◽  
Low Density ◽  
Polypropylene Composites ◽  
Pp Composites ◽  
Potential Use

Polypropylene (PP) composites were prepared by using additives CaCO3/rice husk ash (RHA) as filler, low density polyethylene (LDPE) as modifier, and jute fiber as reinforcement. The effects of filler, modifier, and chemically treated and untreated jute fiber reinforcement on the mechanical properties of the PP composites were studied. The result shows that incorporation of RHA in the PP matrix improves the tensile properties up to 16% which is almost similar to that of CaCO3 incorporated PP composite. This result clearly indicates the potential use of RHA as filler in % LDPE, and 30 wt% jute fiber.

Effects of microcrystalline cellulose on the mechanical properties of low-density polyethylene composites

2018 ◽  
Vol 32 (3) ◽  
pp. 297-311 ◽  
Author(s):  
Yousef Ahmad Mubarak ◽  
Raghda Talal Abdulsamad
Keyword(s):  
Mechanical Properties ◽  
Elastic Modulus ◽  
Impact Strength ◽  
Tensile Properties ◽  
Microcrystalline Cellulose ◽  
Weight Fraction ◽  
Low Density Polyethylene ◽  
Low Density ◽  
Ldpe Composites ◽  
The Impact

This work was intended to provide an understanding of the effect of microcrystalline cellulose (MCC) on the mechanical properties of low-density polyethylene (LDPE). The impact resistance and the tensile properties of low-density LDPE/MCC composites were investigated. The weight fraction of MCC was varied at (0, 0.5, 1, 2.5, 5, 10, 20, and 30 wt%). The obtained blends were then used to prepare the required tensile and impact testing samples by hot compression molding technique. It has been found that MCC has a strong influence on the mechanical properties of LDPE. At a low MCC weight fraction, there was a little improvement in the ultimate strength, fracture stress, and elongation at break, but at a high MCC weight fraction, the tensile properties were deteriorated and reduced significantly. The addition of 1 wt% MCC to LDPE enhanced the mentioned properties by 10, 25, and 6%, respectively. While at 30 wt% MCC, these properties were lowered by 36, 25, and 96%. The elastic modulus of LDPE composites was improved on all MCC weight fractions used in the study, at 20 wt% MCC, an increase in the elastic modulus by 12 folds was achieved. On the other hand and compared with the impact strength of pure LDPE, the addition of MCC particles enhanced the impact strength, the highest value obtained was for LDPE composites filled with 10 wt% MCC where the impact strength enhanced by two folds.

scholarly journals Flame Retardant Polypropylene Composites with Low Densities

Materials ◽  
2019 ◽  
Vol 12 (1) ◽  
pp. 152 ◽  
Author(s):  
Nerea Pérez ◽  
Xiao-Lin Qi ◽  
Shibin Nie ◽  
Pablo Acuña ◽  
Ming-Jun Chen ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Flame Retardant ◽  
Flame Retardancy ◽  
Zirconium Phosphate ◽  
Synergetic Effect ◽  
Low Density ◽  
Material Density ◽  
Polypropylene Composites ◽  
Peak Heat Release Rate ◽  
Pp Composites

Polypropylene (PP) is currently widely used in areas requiring lightweight materials because of its low density. Due to the intrinsic flammability, the application of PP is restricted in many conditions. Aluminum trihydroxide (ATH) is reported as a practical flame retardant for PP, but the addition of ATH often diminishes the lightweight advantage of PP. Therefore, in this work, glass bubbles (GB) and octacedylamine-modified zirconium phosphate (mZrP) are introduced into the PP/ATH composite in order to lower the material density and simultaneously maintain/enhance the flame retardancy. A series of PP composites have been prepared to explore the formulation which can endow the composite with balanced flame retardancy, good mechanical properties, and low density. The morphology, thermal stability, flame retardancy, and mechanical properties of the composites were characterized. The results indicated the addition of GB could reduce the density, but decreased the flame retardancy of PP composites at the same time. To overcome this defect, ATH and mZrP with synergetic effect of flame retardancy were added into the composite. The dosage of each additive was optimized for achieving a balance of flame retardancy, good mechanical properties, and density. With 47 wt % ATH, 10 wt % GB, and 3 wt % mZrP, the peak heat release rate (pHRR) and total smoke production (TSP) of the composite PP-4 were reduced by 91% and 78%, respectively. At the same time, increased impact strength was achieved compared with neat PP and the composite with ATH only. Maintaining the flame retardancy and mechanical properties, the density of composite PP-4 (1.27 g·cm−3) is lower than that with ATH only (PP-1, 1.46 g·cm−3). Through this research, we hope to provide an efficient approach to designing flame retardant polypropylene (PP) composites with low density.

scholarly journals Fabrication and Characterization of Jute Fiber Reinforced Low Density Polyethylene Based Composites: Effects of Chemical Treatment

2011 ◽  
Vol 3 (2) ◽  
pp. 249-259 ◽  
Author(s):  
M. J. Miah ◽  
M. A. Khan ◽  
R. A. Khan
Keyword(s):  
Mechanical Properties ◽  
Dielectric Constant ◽  
Tensile Strength ◽  
Loss Tangent ◽  
Chemical Treatment ◽  
Bending Strength ◽  
Jute Fiber ◽  
Low Density Polyethylene ◽  
Low Density ◽  
Jute Fibers

Jute fiber reinforced low density polyethylene (LDPE) composites (10-30% fiber, by weight) are prepared by compression molding. Tensile strength (TS), bending strength (BS) and bending elongation (BE) of the composites are increased over LDPE.  Jute fiber is treated with monomer (2-hydroxyethyl methacrylate, HEMA) along with two different initiators in methanol solvent. Jute fibers are soaked with 10% HEMA+2% Irgacure-184 (F1-Formulation) and 3% HEMA+2% benzol peroxide (F2-Formulation) and dried at 80ºC for 2 hours then composites are fabricated by compression molding. It is found that due to chemical treatment of the jute fibers, a significant improvement of the mechanical properties of the composites are happened (56% TS, 30% BS and 35% BE) compared to the LDPE. 3%HEMA+2% benzol peroxide treated jute composites found better mechanical properties compared to 10%HEMA+2% Irgacure-184 treated jute composites. Dielectric constant and loss tangent of the composites are increased with increasing temperature up to a transition temperature and then decreased, finally reached to plateau. Scanning Electron Microscopic (SEM) analysis of the fracture side of the composites are carried out and supported better fiber-matrix adhesion due to the chemical treatment.Keywords: Jute fiber; Polyethylene; Composite; Tensile strength; Bending strength; Dielectric constant; Loss tangent.© 2011 JSR Publications. ISSN: 2070-0237 (Print); 2070-0245 (Online). All rights reserved.doi:10.3329/jsr.v3i2.6763               J. Sci. Res. 3 (2), 249-259 (2011)

Effects of Filler Incorporation Routes on Mechanical Properties of Low Density Polyethylene/Natural Rubber/Silica (LDPE/NR/Si) Composites

2014 ◽  
Vol 679 ◽  
pp. 154-157 ◽  
Author(s):  
Pei Ying Teoh ◽  
Abdulbaset Mohamed Erfeida ◽  
Xuan Viet Cao ◽  
Du Ngoc Uy Lan
Keyword(s):  
Mechanical Properties ◽  
Natural Rubber ◽  
Tensile Properties ◽  
Low Density Polyethylene ◽  
Tensile Fracture ◽  
Low Density ◽  
Tensile Fracture Surface ◽  
Roll Mill ◽  
Typical Morphology ◽  
Internal Mixer

Low density polyethylene (LDPE) and natural rubber (NR) filled silica composites were prepared by using internal mixer (Brabender) at 150°C and 50 rpm for 10 minutes. Silica was incorporated into polymer matrix by three mixing routes by using Brabender. In mixing I, filler was added into LDPE/NR blend. In mixing II, filler was added prior to LDPE, which was further compounded with NR. In mixing III, filled was pre-dispersed into NR using two-roll mill, after that the compound is blended with LDPE. The effects of filler incorporation routes on the morphological and tensile properties of prepared composites were studied. Observation from SEM result showed that silica tended to localize in NR phase than LDPE phase in the composite. In addition, silica filled LDPE/NR composite exhibited the highest tensile strength in mixing II and lowest in mixing III. Tensile fracture surface of the composites showed typical morphology of LDPE and NR phase depending on mixing methods. KEYWORDS: LDPE/NR, silica, mixing order, tensile properties, morphology

Effect of water environment on jute/polypropylene composites

2011 ◽  
Vol 18 (1-2) ◽  
pp. 87-92 ◽  
Author(s):  
Tohru Morii ◽  
Seiji Tomioka ◽  
Hiroyuki Hamada
Keyword(s):  
Tensile Properties ◽  
Fiber Type ◽  
Water Immersion ◽  
Water Environment ◽  
Fiber Content ◽  
Jute Fiber ◽  
Weight Changes ◽  
Material Loss ◽  
Polypropylene Composites ◽  
Pp Composites

AbstractThis study investigates the effects of water immersion on tensile properties of jute fiber reinforced polypropylene (PP) composites. The long fiber type jute/PP pellet and neat PP pellet were used as materials and the jute/PP specimens with different fiber content were prepared by injection molding with dry-blending of jute/PP and neat PP pellets. All the specimens were aged in hot distilled water at 80°C, and after the fixed periods of immersion, the weight changes and the tensile properties were measured. The weight gain by water absorption was significantly affected by the fiber content. The specimens with the jute fiber content of 30 wt% more easily absorbed water and it reached more than 10%. In these specimens, significant material loss by immersion also occurred. The tensile strength after immersion decreased remarkably in the specimens with the jute fiber content of 30 wt% and more, and all the jute/PP composites showed lower strength than neat PP after immersion of 1000 h.

scholarly journals Low-Temperature Mechanical Properties of High-Density and Low-Density Polyethylene and Their Blends

Polymers ◽  
2021 ◽  
Vol 13 (11) ◽  
pp. 1821
Author(s):  
Ildar I. Salakhov ◽  
Nadim M. Shaidullin ◽  
Anatoly E. Chalykh ◽  
Mikhail A. Matsko ◽  
Alexey V. Shapagin ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Low Temperature ◽  
Impact Strength ◽  
Relative Elongation ◽  
High Density ◽  
Low Density Polyethylene ◽  
Low Density ◽  
Elongation At Break ◽  
Subzero Temperatures ◽  
Izod Impact

Low-temperature properties of high-density polyethylene (HDPE), low-density polyethylene (LDPE), linear low-density polyethylene (LLDPE), and their blends were studied. The analyzed low-temperature mechanical properties involve the deformation resistance and impact strength characteristics. HDPE is a bimodal ethylene/1-hexene copolymer; LDPE is a branched ethylene homopolymer containing short-chain branches of different length; LLDPE is a binary ethylene/1-butene copolymer and an ethylene/1-butene/1-hexene terpolymer. The samples of copolymers and their blends were studied by gel permeation chromatography (GPC), differential scanning calorimetry (DSC), 13С NMR spectroscopy, and dynamic mechanical analysis (DMA) using testing machines equipped with a cryochamber. It is proposed that such parameters as “relative elongation at break at −45 °C” and “Izod impact strength at −40 °C” are used instead of the ductile-to-brittle transition temperature to assess frost resistance properties because these parameters are more sensitive to deformation and impact at subzero temperatures for HDPE. LLDPE is shown to exhibit higher relative elongation at break at −45 °C and Izod impact strength at −20 ÷ 60 °C compared to those of LDPE. LLDPE terpolymer added to HDPE (at a content ≥ 25 wt.%) simultaneously increases flow properties and improves tensile properties of the blend at −45 °C. Changes in low-temperature properties as a function of molecular weight, MWD, crystallinity, and branch content were determined for HDPE, LLDPE, and their blends. The DMA data prove the resulting dependences. The reported findings allow one to understand and predict mechanical properties in the HDPE–LLDPE systems at subzero temperatures.

scholarly journals Improving the mechanical properties of polypropylene composites with coconut shell particles

2021 ◽  
Vol 30 ◽  
pp. 263498332110074
Author(s):  
Henry C Obasi ◽  
Uchechi C Mark ◽  
Udochukwu Mark
Keyword(s):  
Mechanical Properties ◽  
Particle Size ◽  
Flexural Modulus ◽  
Filler Particle ◽  
Tensile Modulus ◽  
Coconut Shell ◽  
Polypropylene Composites ◽  
Increase With Increase ◽  
Pp Composites ◽  
Shell Particles

Conventional inorganic fillers are widely used as fillers for polymer-based composites. Though, their processing difficulties and cost have demanded the quest for credible alternatives of organic origin like coconut shell fillers. Dried shells of coconut were burnt, ground, and sifted to sizes of 63, 150, 300, and 425 µm. The ground coconut shell particles (CSP) were used as a filler to prepare polypropylene (PP) composites at filler contents of 0% to 40% via injection melt blending process to produce PP composite sheets. The effect of the filler particle size on the mechanical properties was investigated. The decrease in the size of filler (CSP) was found to improve the yield strength, tensile strength, tensile modulus, flexural strength, flexural modulus, and hardness of PP by 8.5 MPa, 15.75 MPa, 1.72 GPa, 7.5 MPa, 100 MPa, and 10.5 HR for 63 µm at 40%, respectively. However, the elongation at break and modulus of resilience of the PP composites were seen to increase with increase in the filler size. Scanning electron microscope analysis showed that fillers with 63 µm particle size had the best distribution and interaction with the PP matrix resulting in enhanced properties.

Sign in / Sign up

Export Citation Format

Share Document