scholarly journals Tantalum Nanoparticles Reinforced PCL Scaffolds Using Direct 3D Printing for Bone Tissue Engineering

2021 ◽  
Vol 8 ◽  
Author(s):  
Zixuan Xiong ◽  
Wenbin Liu ◽  
Hu Qian ◽  
Ting Lei ◽  
Xi He ◽  
...  
Keyword(s):  
Gene Expression ◽  
Tissue Engineering ◽  
Biological Activity ◽  
Cell Adhesion ◽  
3D Printing ◽  
Orthopedic Implants ◽  
Biological Properties ◽  
Related Gene ◽  
Clinical Potential

Polycarbonate (PCL) has been widely used in tissue engineering, but its hydrophobicity and low biological activity limit its further promotion and application. By adding nanoparticles, the hydrophilicity and biological activity of PCL can be improved. In this study, different amounts of Ta (1–10%wt) were added to PCL, and then their mechanical and biological properties were studied in vitro. XRD found that 5%Ta-PCL has the highest crystallinity. At the same time, cell experiments CCK8, cell adhesion, osteogenic differentiation, and osteogenesis related gene expression showed that Ta can enhance the mechanical and biological properties of PCL, while 5% Ta-PCL showed the best mechanical and biological properties. This composite of tantalum and PCL could have a clinical potential for orthopedic implants.

Fabrication and characterization of customized tubular scaffolds for tracheal tissue engineering by using solvent based 3D printing on predefined template

2021 ◽  
Vol 27 (2) ◽  
pp. 421-428
Author(s):  
Rudranarayan Kandi ◽  
Pulak Mohan Pandey ◽  
Misba Majood ◽  
Sujata Mohanty
Keyword(s):  
Tissue Engineering ◽  
Cell Adhesion ◽  
3D Printing ◽  
Chemical Properties ◽  
Contact Angle Measurement ◽  
Angle Measurement ◽  
In Vitro Cytotoxicity ◽  
Content Type ◽  
Tracheal Tissue

Purpose This paper aims to discuss the successful fabrication of customized tubular scaffolds for tracheal tissue engineering with a novel route using solvent-based extrusion 3D printing. Design/methodology/approach The manufacturing approach involved extrusion of polymeric ink over a rotating predefined pattern to construct customized tubular structure of polycaprolactone (PCL) and polyurethane (PU). Dimensional deviation in thickness of scaffolds were calculated for various layer thicknesses of 3D printing. Physical and chemical properties of scaffolds were investigated by scanning electron microscope (SEM), contact angle measurement, Fourier Transform Infrared Spectroscopy (FTIR) and X-ray diffraction (XRD). Mechanical characterizations were performed, and the results were compared to the reported properties of human native trachea from previous reports. Additionally, in vitro cytotoxicity of the fabricated scaffolds was studied in terms of cell proliferation, cell adhesion and hemagglutination assay. Findings The developed fabrication route was flexible and accurate by printing customized tubular scaffolds of various scales. Physiochemical results showed good miscibility of PCL/PU blend, and decrease in crystalline nature of blend with the addition of PU. Preliminary mechanical assessments illustrated comparable mechanical properties with the native human trachea. Longitudinal compression test reported outstanding strength and flexibility to maintain an unobstructed lumen, necessary for the patency. Furthermore, the scaffolds were found to be biocompatible to promote cell adhesion and proliferation from the in vitro cytotoxicity results. Practical implications The attempt can potentially meet the demand for flexible tubular scaffolds that ease the concerns such as availability of suitable organ donors. Originality/value 3D printing over accurate predefined templates to fabricate customized grafts gives novelty to the present method. Various customized scaffolds were compared with conventional cylindrical scaffold in terms of flexibility.

The influence of titanium surfaces treated by alkalis on macrophage and osteoblast-like cell adhesion and gene expression in vitro

RSC Advances ◽  
2015 ◽  
Vol 5 (99) ◽  
pp. 81378-81387 ◽  
Author(s):  
Ting Ma ◽  
Xi-Yuan Ge ◽  
Sheng-Nan Jia ◽  
Xi Jiang ◽  
Yu Zhang ◽  
...  
Keyword(s):  
Gene Expression ◽  
Alkaline Phosphatase ◽  
Cell Adhesion ◽  
Phosphatase Activity ◽  
Alkaline Phosphatase Activity ◽  
Related Gene ◽  
Titanium Surfaces

The effect of alkali-treated titanium surfaces on inflammation-related gene expression of macrophages and alkaline phosphatase activity of osteoblast-like cells.

scholarly journals Fabrication and In Vitro Evaluation of 3D Printed Porous Polyetherimide Scaffolds for Bone Tissue Engineering

2019 ◽  
Vol 2019 ◽  
pp. 1-8 ◽  
Author(s):  
Xiongfeng Tang ◽  
Yanguo Qin ◽  
Xinyu Xu ◽  
Deming Guo ◽  
Wenli Ye ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tissue Engineering ◽  
Cell Proliferation ◽  
Cell Adhesion ◽  
3D Printing ◽  
Bone Tissue Engineering ◽  
Bone Tissue ◽  
Porous Scaffold ◽  
3D Printed

For bone tissue engineering, the porous scaffold should provide a biocompatible environment for cell adhesion, proliferation, and differentiation and match the mechanical properties of native bone tissue. In this work, we fabricated porous polyetherimide (PEI) scaffolds using a three-dimensional (3D) printing system, and the pore size was set as 800 μm. The morphology of 3D PEI scaffolds was characterized by the scanning electron microscope. To investigate the mechanical properties of the 3D PEI scaffold, the compressive mechanical test was performed via an electronic universal testing system. For the in vitro cell experiment, bone marrow stromal cells (BMSCs) were cultured on the surface of the 3D PEI scaffold and PEI slice, and cytotoxicity, cell adhesion, and cell proliferation were detected to verify their biocompatibility. Besides, the alkaline phosphatase staining and Alizarin Red staining were performed on the BMSCs of different samples to evaluate the osteogenic differentiation. Through these studies, we found that the 3D PEI scaffold showed an interconnected porous structure, which was consistent with the design. The elastic modulus of the 3D PEI scaffold (941.33 ± 65.26 MPa) falls in the range of modulus for the native cancellous bone. Moreover, the cell proliferation and morphology on the 3D PEI scaffold were better than those on the PEI slice, which revealed that the porous scaffold has good biocompatibility and that no toxic substances were produced during the progress of high-temperature 3D printing. The osteogenic differentiation level of the 3D PEI scaffold and PEI slice was equal and ordinary. All of these results suggest the 3D printed PEI scaffold would be a potential strategy for bone tissue engineering.

Biological properties of novel chitosan-based composites for medical application as bone substitute

2014 ◽  
Vol 9 (6) ◽  
pp. 634-641 ◽  
Author(s):  
Agata Przekora ◽  
Grażyna Ginalska
Keyword(s):  
Mechanical Properties ◽  
Cell Adhesion ◽  
Bone Substitute ◽  
Medical Application ◽  
Bone Substitutes ◽  
Biological Properties ◽  
Alp Activity ◽  
Osteoblast Cell Line ◽  
Clinical Potential

AbstractHydroxyapatite is the main inorganic component of bones and teeth. In order to improve mechanical properties and surgical handiness of bioceramics, a plasticizing agent e.g. polysaccharide can be added. Chitosan is a polysaccharide with biological properties that make it an ideal component of bioceramics-based composites for medical application as bone substitute. In this study, biocompatibility of two types of novel krill chitosan-based composites was evaluated. In vitro experiments were carried out using human foetal osteoblast cell line. Cytotoxicity, cell adhesion, and bone ALP activity tests were performed to assess biocompatibility of the composites. Osteoblast growth on composites was observed using confocal microscope. Our results demonstrated that fabricated novel composites are non-toxic, are favorable to cell adhesion and growth, and provoke increase in b-ALP activity with time, thus inducing osteoblast differentiation. Based on this data composites have promising clinical potential as a bone defect filler in regenerative medicine. It is worth emphasizing that our work resulted in fabrication of flexible and surgical handy, bone substitutes that possess absolute biocompatibility with structural and mechanical properties similar to trabecular bone.

scholarly journals 3D Printing of Polycaprolactone–Polyaniline Electroactive Scaffolds for Bone Tissue Engineering

Materials ◽  
2020 ◽  
Vol 13 (3) ◽  
pp. 512 ◽  
Author(s):  
Arie Wibowo ◽  
Cian Vyas ◽  
Glen Cooper ◽  
Fitriyatul Qulub ◽  
Rochim Suratman ◽  
...  
Keyword(s):  
Tissue Engineering ◽  
3D Printing ◽  
Cell Viability ◽  
Bone Tissue Engineering ◽  
Bone Tissue ◽  
Polymeric Composite ◽  
Biological Properties ◽  
Initial Development ◽  
Cellular Behaviour

Electrostimulation and electroactive scaffolds can positively influence and guide cellular behaviour and thus has been garnering interest as a key tissue engineering strategy. The development of conducting polymers such as polyaniline enables the fabrication of conductive polymeric composite scaffolds. In this study, we report on the initial development of a polycaprolactone scaffold incorporating different weight loadings of a polyaniline microparticle filler. The scaffolds are fabricated using screw-assisted extrusion-based 3D printing and are characterised for their morphological, mechanical, conductivity, and preliminary biological properties. The conductivity of the polycaprolactone scaffolds increases with the inclusion of polyaniline. The in vitro cytocompatibility of the scaffolds was assessed using human adipose-derived stem cells to determine cell viability and proliferation up to 21 days. A cytotoxicity threshold was reached at 1% wt. polyaniline loading. Scaffolds with 0.1% wt. polyaniline showed suitable compressive strength (6.45 ± 0.16 MPa) and conductivity (2.46 ± 0.65 × 10−4 S/cm) for bone tissue engineering applications and demonstrated the highest cell viability at day 1 (88%) with cytocompatibility for up to 21 days in cell culture.

scholarly journals Three-dimensionally printed polycaprolactone/multicomponent bioactive glass scaffolds for potential application in bone tissue engineering

2020 ◽  
Vol 6 (1) ◽  
pp. 57-69
Author(s):  
Amirhosein Fathi ◽  
Farzad Kermani ◽  
Aliasghar Behnamghader ◽  
Sara Banijamali ◽  
Masoud Mozafari ◽  
...  
Keyword(s):  
Tissue Engineering ◽  
3D Printing ◽  
Bone Tissue Engineering ◽  
Bone Tissue ◽  
Three Dimensional ◽  
Layer By Layer ◽  
Composite Scaffolds ◽  
3D Printed ◽  
Co Doped

AbstractOver the last years, three-dimensional (3D) printing has been successfully applied to produce suitable substitutes for treating bone defects. In this work, 3D printed composite scaffolds of polycaprolactone (PCL) and strontium (Sr)- and cobalt (Co)-doped multi-component melt-derived bioactive glasses (BGs) were prepared for bone tissue engineering strategies. For this purpose, 30% of as-prepared BG particles (size <38 μm) were incorporated into PCL, and then the obtained composite mix was introduced into a 3D printing machine to fabricate layer-by-layer porous structures with the size of 12 × 12 × 2 mm3.The scaffolds were fully characterized through a series of physico-chemical and biological assays. Adding the BGs to PCL led to an improvement in the compressive strength of the fabricated scaffolds and increased their hydrophilicity. Furthermore, the PCL/BG scaffolds showed apatite-forming ability (i.e., bioactivity behavior) after being immersed in simulated body fluid (SBF). The in vitro cellular examinations revealed the cytocompatibility of the scaffolds and confirmed them as suitable substrates for the adhesion and proliferation of MG-63 osteosarcoma cells. In conclusion, 3D printed composite scaffolds made of PCL and Sr- and Co-doped BGs might be potentially-beneficial bone replacements, and the achieved results motivate further research on these materials.

Cell shape and gene expression in human intervertebral disc cells: in vitro tissue engineering studies

2003 ◽  
Vol 78 (2) ◽  
pp. 109-117 ◽  
Author(s):  
He Gruber ◽  
Ja Ingram ◽  
K Leslie ◽  
Hj Norton ◽  
En Hanley Jr
Keyword(s):  
Gene Expression ◽  
Tissue Engineering ◽  
Intervertebral Disc ◽  
Cell Shape ◽  
Engineering Studies ◽  
Disc Cells

scholarly journals Influences of Molecular Weights on Physicochemical and Biological Properties of Collagen-Alginate Scaffolds

Marine Drugs ◽  
2021 ◽  
Vol 19 (2) ◽  
pp. 85 ◽  
Author(s):  
Truc Cong Ho ◽  
Jin-Seok Park ◽  
Sung-Yeoul Kim ◽  
Hoyeol Lee ◽  
Ju-Sop Lim ◽  
...  
Keyword(s):  
Tissue Engineering ◽  
Subcritical Water ◽  
Biological Properties ◽  
Ethanol Solution ◽  
Water Soluble ◽  
Potential Candidate ◽  
High Porosity ◽  
Engineering Applications ◽  
Molecular Weights

For tissue engineering applications, biodegradable scaffolds containing high molecular weights (MW) of collagen and sodium alginate have been developed and characterized. However, the properties of low MW collagen-based scaffolds have not been studied in previous research. This work examined the distinctive properties of low MW collagen-based scaffolds with alginate unmodified and modified by subcritical water. Besides, we developed a facile method to cross-link water-soluble scaffolds using glutaraldehyde in an aqueous ethanol solution. The prepared cross-linked scaffolds showed good structural properties with high porosity (~93%) and high cross-linking degree (50–60%). Compared with collagen (6000 Da)-based scaffolds, collagen (25,000 Da)-based scaffolds exhibited higher stability against collagenase degradation and lower weight loss in phosphate buffer pH 7.4. Collagen (25,000 Da)-based scaffolds with modified alginate tended to improve antioxidant capacity compared with scaffolds containing unmodified alginate. Interestingly, in vitro coagulant activity assay demonstrated that collagen (25,000 Da)-based scaffolds with modified alginate (C25-A63 and C25-A21) significantly reduced the clotting time of human plasma compared with scaffolds consisting of unmodified alginate. Although some further investigations need to be done, collagen (25,000 Da)-based scaffolds with modified alginate should be considered as a potential candidate for tissue engineering applications.

scholarly journals Porous Cellulose-Collagen Scaffolds For Soft Tissue Regeneration: Influence of Cellulose Derivatives On Mechanical Properties And Compatibility With Adipose-Derived Stem Cells.

2022 ◽  
Author(s):  
Katarína Kacvinská ◽  
Martina Trávničková ◽  
Lucy Vojtová ◽  
Petr Poláček ◽  
Jana Dorazilová ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tissue Engineering ◽  
Stem Cells ◽  
Cell Adhesion ◽  
Soft Tissue ◽  
Vascular Tissue ◽  
Biological Properties ◽  
Cellulose Derivatives ◽  
Adipose Derived Stem Cells ◽  
Soft Tissue Regeneration

Abstract This study deals with cellulose derivatives in relation to the collagen fibrils in composite collagen-cellulose scaffolds for soft tissue engineering. Two types of cellulose, i.e., oxidized cellulose (OC) and carboxymethyl cellulose (CMC), were blended with collagen (Col) to enhance its elasticity, stability and sorptive biological properties, e.g. hemostatic and antibacterial features. The addition of OC supported the resistivity of the Col fibrils in a dry environment, while in a moist environment OC caused a radical drop. The addition of CMC reduced the mechanical strength of the Col fibrils in both environments. The elongation of the Col fibrils was increased by both types of cellulose derivatives in both environments, which is closely related to tissue like behaviour. In these various mechanical environments, the ability of human adipose-derived stem cells (hADSCs) to adhere and proliferate was significantly greater in the Col and Col/OC scaffolds than in the Col/CMC scaffold. This is explained by deficient mechanical support and loss of stiffness due to the high swelling capacity of CMC. Although Col/OC and Col/CMC acted differently in terms of mechanical properties, both materials were observed to be cytocompatible, with varying degrees of further support for cell adhesion and proliferation. While Col/OC can serve as a scaffolding material for vascular tissue engineering and for skin tissue engineering, Col/CMC seems to be more suitable for moist wound healing, e.g. as a mucoadhesive gel for exudate removal, since there was almost no cell adhesion.

Sign in / Sign up

Export Citation Format

Share Document