scholarly journals Effect of a Circular Slot on Hybrid Airship Aerodynamic Characteristics

Aerospace ◽  
2021 ◽  
Vol 8 (6) ◽  
pp. 166
Author(s):  
Sekar Mano ◽  
RadhaKrishnan Ajay Sriram ◽  
Ganesan Vinayagamurthy ◽  
Subramania Nadaraja Pillai ◽  
Amjad Ali Pasha ◽  
...  
Keyword(s):  
Numerical Study ◽  
Flow Behavior ◽  
Lift Coefficient ◽  
Pressure Coefficient ◽  
Suction Side ◽  
Aerodynamic Characteristics ◽  
Aerodynamic Properties ◽  
Slot Opening ◽  
Stall Angle ◽  
High Pressure Region

This numerical study reports the aerodynamic properties of a hybrid airship. The hybrid airships were designed by combining two semi-ellipsoids with a semi-discoid as the base model. From the base model, three different geometrics were identified to study their aerodynamic characteristics. A circular slot was provided between the pressure side and the suction side of the airship. The objective of this study was to realize the flow behavior, aerodynamic characteristics, and stability properties of such slotted hybrid flying vehicles. Interestingly, the results imply that the lift coefficient increases with an increase in the angle of attack for the slotted configurations; this is because the flow separation is delayed due to the slot opening, which in turn is due to the flow of energies from the high-pressure region to the bottom through the slots. The delayed stall angle was 50 degrees, which was 10% more than that of the base model. Aerodynamic characteristics are discussed based on surface pressure, coefficient of lift, and coefficient of drag for various slotted hybrid airships.

scholarly journals Effect of the Backward-Facing Step Location on the Aerodynamics of a Morphing Wing

2021 ◽  
Author(s):  
Fadi Magdy R Mishriky ◽  
Paul Walsh
Keyword(s):  
Drag Coefficient ◽  
Transition Point ◽  
Numerical Study ◽  
Lift Coefficient ◽  
Suction Side ◽  
Backward Facing Step ◽  
Viscous Boundary Layer ◽  
Airfoil Surface ◽  
Aerodynamic Properties ◽  
Lift And Drag

Over the last decade, aircraft morphing technology has drawn a lot of attention in the aerospace community, because it is likely to improve the aerodynamic performance and the versatility of aircraft at different flight regimes. With the fast paced advancements in this field, a parallel stream of research is studying different materials and designs to develop reliable morphing skins. A promising candidate for a viable morphing skin is the sliding skin, where two or more rigid surfaces remain in contact and slide against each other during morphing. The overlapping between each two panels create a backward-facing step on the airfoil surface which has a critical effect on the aerodynamics of the wing. This paper presents a numerical study of the effect of employing a backward-facing step on the suction side of a National Advisory Committee for Aeronautics (NACA) 2412 airfoil at a high Reynolds number of 5.9 × 106. The effects of the step location on the lift coefficient, drag coefficient and critical angle of attack are studied to find a favorable location for the step along the chord-wise direction. Results showed that employing a step on the suction side of the NACA 2412 airfoil can adversely affect the aforementioned aerodynamic properties. A drop of 21.1% in value of the lift coefficient and an increase of 120.8% in the drag coefficient were observed in case of a step located at 25% of the chord length. However, these effects are mitigated by shifting the step location towards the trailing edge. Introducing a step on the airfoil caused the airfoil’s thickness to change, which in turn has affected the transition point of the viscous boundary layer from laminar to turbulent. The location of the step, prior or post the transition point, has a noteworthy effect on the pressure and shear stress distribution, and consequently on the values of the lift and drag coefficients.

scholarly journals Effect of the Backward-Facing Step Location on the Aerodynamics of a Morphing Wing

2021 ◽  
Author(s):  
Rshare Library ◽  
Fadi Magdy R Mishriky ◽  
Paul Walsh
Keyword(s):  
Drag Coefficient ◽  
Transition Point ◽  
Numerical Study ◽  
Lift Coefficient ◽  
Suction Side ◽  
Backward Facing Step ◽  
Viscous Boundary Layer ◽  
Airfoil Surface ◽  
Aerodynamic Properties ◽  
Lift And Drag

Over the last decade, aircraft morphing technology has drawn a lot of attention in the aerospace community, because it is likely to improve the aerodynamic performance and the versatility of aircraft at different flight regimes. With the fast paced advancements in this field, a parallel stream of research is studying different materials and designs to develop reliable morphing skins. A promising candidate for a viable morphing skin is the sliding skin, where two or more rigid surfaces remain in contact and slide against each other during morphing. The overlapping between each two panels create a backward-facing step on the airfoil surface which has a critical effect on the aerodynamics of the wing. This paper presents a numerical study of the effect of employing a backward-facing step on the suction side of a National Advisory Committee for Aeronautics (NACA) 2412 airfoil at a high Reynolds number of 5.9 × 106. The effects of the step location on the lift coefficient, drag coefficient and critical angle of attack are studied to find a favorable location for the step along the chord-wise direction. Results showed that employing a step on the suction side of the NACA 2412 airfoil can adversely affect the aforementioned aerodynamic properties. A drop of 21.1% in value of the lift coefficient and an increase of 120.8% in the drag coefficient were observed in case of a step located at 25% of the chord length. However, these effects are mitigated by shifting the step location towards the trailing edge. Introducing a step on the airfoil caused the airfoil’s thickness to change, which in turn has affected the transition point of the viscous boundary layer from laminar to turbulent. The location of the step, prior or post the transition point, has a noteworthy effect on the pressure and shear stress distribution, and consequently on the values of the lift and drag coefficients.

Numerical Study on Aerodynamic Characteristics of NACA0015

2013 ◽  
Vol 302 ◽  
pp. 640-645
Author(s):  
Su Jeong Lee ◽  
Eui Chul Jeong ◽  
Hee Chang Lim
Keyword(s):  
Pressure Distribution ◽  
Numerical Study ◽  
Lift Coefficient ◽  
Angle Of Attack ◽  
Vertical Axis ◽  
Aerodynamic Characteristics ◽  
Surface Pressure Distribution ◽  
Maximum Value ◽  
Stall Angle ◽  
Near Wall

In this study, a numerical simulation is made to understand the effect of the angle of attack on a NACA airfoil, which will be used for a basic shape to apply for making the vertical axis Darius wind turbine. The near-wall y+ value which is less than 1 is known to be most desirable for a near-wall modeling. Therefore, this study is aiming to observe the variation and find the optimized value of y+. The Reynolds number used in this study was 360,000, where the chord length and the velocity were 0.12m and 43.8m/s, respectively. Generally, the lift coefficient of the airfoil tends to increase as the angle of attack increases and it decreases substantially at the stall angle and then it decreases. As expected, the lift coefficient increases rapidly from 0 to 10° and then after the sudden drop of the lift (i.e., the stall) at around 10 to 16° depending on the y+ value. In this paper, it seems to be reliable and appropriate to use y+ value close to 1. From the surface pressure distribution, from the result obtained the ratio of pressure distribution of maximum value to the minimum value was 1.89and these peaks move forward to backward as the angle of attack increases.

Effect of Shapes and Turbulent Inlet Flow to Vortices on Delta Wings

2019 ◽  
Vol 889 ◽  
pp. 434-439
Author(s):  
Ngoc Khanh Tran ◽  
Van Khang Nguyen ◽  
Phu Khanh Nguyen ◽  
Thi Kim Dung Hoang ◽  
Van Quang Dao
Keyword(s):  
Turbulence Intensity ◽  
Delta Wing ◽  
Lift Coefficient ◽  
Pressure Coefficient ◽  
Leading Edge ◽  
Aerodynamic Characteristics ◽  
Delta Wings ◽  
Ansys Fluent ◽  
Inlet Flow ◽  
Stall Angle

This paper aims to estimate the effect of turbulent inlet flow to vortices on Delta wing with four different turbulence intensity from 0.5% to 15% and the effect of taper ratios to aerodynamic characteristics of Delta wings with four taper ratios: 0, 0.1, 0.2, 0.3, 0.4, 0.5, 0.6, 0.7. The main purpose of this paper is to find out the formation, development, and breakdown of vortices on Delta wings when changing taper ratios and turbulence intensity thence determining the center of vortices with the range of attack angles from 5o to 40o in low velocities about 2.5 m/s. This research uses Delta wing models with a 40o swept-back leading edge, the root chord length 150 mm, and a thickness 5 mm. The problem is simulated by using ANSYS fluent and experiment in the subsonic wind tunnel to compare and validate results. The Delta wing models are meshed by using ICEM to improve the mesh quality and using the turbulence model for low Reynolds number flows Transition SST (4 equations) to calculate aerodynamic characteristics such as lift coefficient, drag coefficient, pressure coefficient... find the paths which connect centers of the vortices, and show the contours of pressures and velocities to evaluate the change of centers of the vortices. The results showed that the two vortices grow up and tend to move inward when the attack angle increase, the vortices are broken strongly in high attack angles, the aerodynamic quality of Delta wings change insignificantly when changing turbulent intensity at inlet. This research also carried out that the stall angle increase when increasing the taper ratio.

A comprehensive numerical study of battle damage and repairs upon the aerodynamic characteristics of an aerofoil

2010 ◽  
Vol 114 (1158) ◽  
pp. 469-484 ◽  
Author(s):  
M. Saeedi ◽  
F. Ajalli ◽  
M. Mani
Keyword(s):  
Flow Field ◽  
Numerical Solution ◽  
Mesh Generation ◽  
Unstructured Mesh ◽  
Numerical Study ◽  
Lift Coefficient ◽  
Aerodynamic Characteristics ◽  
Experimental Results ◽  
The Other ◽  
Stall Angle

Abstract A NACA 641-412 aerofoil with circle and star damage and also three repair configurations has been numerically investigated. Two different methods of mesh generation were employed: multi structured mesh for the star damaged aerofoil and unstructured mesh for the other aerofoils. The results show that the damage will cause a reduction in lift coefficient of the aerofoil and also a different stall angle relative to that of the undamaged aerofoil. Each kind of repair improves the aerodynamic characteristics of the aerofoil considerably. The flow Field inside the damage hole and the cavity caused by the repair sheets was also investigated. Finally, the numerical solution was qualitatively and quantitatively validated using the available experimental results.

scholarly journals Effect of the Backward-Facing Step Location on the Aerodynamics of a Morphing Wing

2021 ◽  
Author(s):  
Rshare Library ◽  
Fadi Magdy R Mishriky ◽  
Paul Walsh
Keyword(s):  
Drag Coefficient ◽  
Transition Point ◽  
Numerical Study ◽  
Lift Coefficient ◽  
Suction Side ◽  
Backward Facing Step ◽  
Viscous Boundary Layer ◽  
Airfoil Surface ◽  
Aerodynamic Properties ◽  
Lift And Drag

Over the last decade, aircraft morphing technology has drawn a lot of attention in the aerospace community, because it is likely to improve the aerodynamic performance and the versatility of aircraft at different flight regimes. With the fast paced advancements in this field, a parallel stream of research is studying different materials and designs to develop reliable morphing skins. A promising candidate for a viable morphing skin is the sliding skin, where two or more rigid surfaces remain in contact and slide against each other during morphing. The overlapping between each two panels create a backward-facing step on the airfoil surface which has a critical effect on the aerodynamics of the wing. This paper presents a numerical study of the effect of employing a backward-facing step on the suction side of a National Advisory Committee for Aeronautics (NACA) 2412 airfoil at a high Reynolds number of 5.9 × 106. The effects of the step location on the lift coefficient, drag coefficient and critical angle of attack are studied to find a favorable location for the step along the chord-wise direction. Results showed that employing a step on the suction side of the NACA 2412 airfoil can adversely affect the aforementioned aerodynamic properties. A drop of 21.1% in value of the lift coefficient and an increase of 120.8% in the drag coefficient were observed in case of a step located at 25% of the chord length. However, these effects are mitigated by shifting the step location towards the trailing edge. Introducing a step on the airfoil caused the airfoil’s thickness to change, which in turn has affected the transition point of the viscous boundary layer from laminar to turbulent. The location of the step, prior or post the transition point, has a noteworthy effect on the pressure and shear stress distribution, and consequently on the values of the lift and drag coefficients.

Numerical study of the aerodynamic and power characteristics of the cycloidal rotor, under incoming flow

2019 ◽  
pp. 25-34
Author(s):  
Александр Анатольевич Дектерев ◽  
Артем Александрович Дектерев ◽  
Юрий Николаевич Горюнов
Keyword(s):  
Flow Velocity ◽  
Numerical Study ◽  
Lift Coefficient ◽  
Simulation Method ◽  
Aerodynamic Characteristics ◽  
Incoming Flow ◽  
Ansys Fluent ◽  
Energy Characteristics ◽  
Power Characteristics ◽  
Calculation Results

Исследование направлено на разработку и апробацию методики численного моделирования аэродинамических и энергетических характеристик циклоидального ротора. За основу взята конфигурация ротора IAT21 L3. Для нее с использованием CFD-пакета ANSYS Fluent построена математическая модель и выполнен расчет. Проанализировано влияние скорости набегающего потока воздуха на движущийся ротор. Математическая модель и полученные результаты исследования могут быть использованы при создании летательных аппаратов с движителями роторного типа. This article addresses the study of the aerodynamic and energy characteristics of a cycloidal rotor subject to the influence of the incoming flow. Cycloidal rotor is one of the perspective devices that provide movement of aircrafts. Despite the fact that the concept of a cycloidal rotor arose in the early twentieth century, the model of a full-scale aircraft has not been yet realized. Foreign scientists have developed models of aircraft ranging in weight from 0.06 to 100 kg. The method of numerical calculation of the cycloidal rotor from the article [1] is considered and realized in this study. The purpose of study was the development and testing of a numerical simulation method for the cycloidal rotor and study aerodynamic and energy characteristics of the rotor in the hovering mode and under the influence of the oncoming flow. The aerodynamic and energy characteristics of the cycloidal rotor, rotating at a speed of 1000 rpm with incoming flow on it with velocities of 20-80 km/h, were calculated. The calculation results showed a directly proportional increase of thrust with an increase of the incoming on the rotor flow velocity, but the power consumed by the rotor was also increased. Increase of the incoming flow velocity leads to the proportional increasing of the lift coefficient and the coefficient of drag. Up to a speed of 80 km/h, an increase in thrust and power is observed; at higher speeds, there is a predominance of nonstationary effects and difficulties in estimating the aerodynamic characteristics of the rotor. In the future, it is planned to consider the 3D formulation of the problem combined with possibility of the flow coming from other sides.

A Numerical Study Into the Influence of Leading Edge Tubercles on the Aerodynamic Performance of a Highly Cambered High Lift Airfoil Wing at Different Reynolds Numbers

2020 ◽  
Author(s):  
Amr Abdelrahman ◽  
Amr Emam ◽  
Ihab Adam ◽  
Hamdy Hassan ◽  
Shinichi Ookawara ◽  
...  
Keyword(s):  
Control Method ◽  
Numerical Study ◽  
Leading Edge ◽  
Suction Side ◽  
Reynolds Numbers ◽  
Passive Flow Control ◽  
Passive Flow ◽  
Stall Angle ◽  
Lifting Surfaces ◽  
Lift And Drag

Abstract Through the last two decades, many studies have demonstrated the ability of leading-edge protrusions (tubercles), inspired from the pectoral flippers of the humpback whale, to be an effective passive flow control method for the stall phase of an airfoil in some cases depending on the geometrical features and the flow regime. Nevertheless, there is a little work associated with revealing tubercles performance for the lifting surfaces with a highly cambered cross-section, used in numerous applications. The present work aims to investigate the effect of implementing leading edge tubercles on the performance of an infinite span rectangular wing with the highly cambered S1223 foil at different flow regimes. Two sets; baseline one and a modified with tubercles have been studied at Re = 0.1 × 106, 0.3 × 106 and 1.5 × 106 using computational fluid dynamics with a validated model. The numerical results demonstrated that Tubercles have the ability to entirely alter the flow structure over the airfoil, confining the separation to troughs, hence, softening the stall characteristics. However, the tubercle modification expedites the presence of the stalled flow over the suction side, lowering the stall angle for the three mentioned Reynolds numbers. While, no considerable difference occurs in lift and drag before the stall.

Numerical Study on Heat Transfer and Flow Characteristics in Double Turning Areas Ribbed Serpentine Channel With Lateral Outflow

2019 ◽  
Author(s):  
Bo-lun Zhang ◽  
Hui-ren Zhu ◽  
Tao Guo ◽  
Chun-yi Yao ◽  
Zhong-yi Fu
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Numerical Study ◽  
Pressure Coefficient ◽  
Flow Characteristics ◽  
Suction Side ◽  
Pressure Side ◽  
Maximum Increase ◽  
Serpentine Channel ◽  
Ratio Condition

Abstract The double turning areas ribbed serpentine channel with lateral outflow is an important structure for designing the internal systems of turbine blade. The current work similarly simplifies the internal channel of the real blade. The Nusselt number and pressure coefficient distribution of the double turning areas ribbed serpentine channel with different outflow ratios are numerically researched under static and rotating conditions. The Realizable k-ε turbulence model with enhanced wall treatment is used in the numerical simulation. The inlet Reynolds number is 11000. The rotation numbers vary from 0 to 0.09. Three outflow ratios are 27%/0%/73%, 27%/49%/24% and 27%/73%/0%, respectively. The rotation radius (R) is 46.4d. The result shows that the Nusselt number distribution of the passage 3 under 27%/49%/24% outflow ratio condition is similar to that under 27%/73%/0% outflow ratio condition. There is a large low Nusselt number area in the passage 3 under Dr = 27%/0%/73% condition. The averaged area Nusselt number ratios on the suction side of the passage 1, passage 2 and passage 3 are higher than that on the pressure side under nonrotating condition. Rotation enhances heat transfer on the suction side of the passage 2, and has a positive effect on pressure side heat transfer of passage 1 and passage 3. The averaged area Nusselt number ratio of passage 3 under 27%/73%/0% outflow ratio condition is higher than that under other outflow ratio conditions. With the rotation number increasing, the pressure coefficient of the complete ribbed serpentine channel gradually increases, and the maximum increase is in the first turning area.

Wind Tunnel Experimental Study of Wind Turbine Airfoil Aerodynamic Characteristics

2012 ◽  
Vol 260-261 ◽  
pp. 125-129
Author(s):  
Xin Zi Tang ◽  
Xu Zhang ◽  
Rui Tao Peng ◽  
Xiong Wei Liu
Keyword(s):  
Wind Tunnel ◽  
Wind Turbine ◽  
Lift Coefficient ◽  
Turbine Blades ◽  
Aerodynamic Characteristics ◽  
Wind Turbine Blades ◽  
High Lift ◽  
Minimum Drag ◽  
Stall Angle ◽  
High Reynolds

High lift and low drag are desirable for wind turbine blade airfoils. The performance of a high lift airfoil at high Reynolds number (Re) for large wind turbine blades is different from that at low Re number for small wind turbine blades. This paper investigates the performance of a high lift airfoil DU93-W-210 at high Re number in low Re number flows through wind tunnel testing. A series of low speed wind tunnel tests were conducted in a subsonic low turbulence closed return wind tunnel at the Re number from 2×105to 5×105. The results show that the maximum lift, minimum drag and stall angle differ at different Re numbers. Prior to the onset of stall, the lift coefficient increases linearly and the slope of the lift coefficient curve is larger at a higher Re number, the drag coefficient goes up gradually as angle of attack increases for these low Re numbers, meanwhile the stall angle moves from 14° to 12° while the Re number changes from 2×105to 5×105.

Sign in / Sign up

Export Citation Format

Share Document