scholarly journals Environmental Remediation of Metribuzin Herbicide by Mesoporous Carbon—Rich from Wheat Straw

2021 ◽  
Vol 11 (11) ◽  
pp. 4935
Author(s):  
Irina Gabriela Cara ◽  
Manuela Filip ◽  
Laura Bulgariu ◽  
Lucian Raus ◽  
Denis Topa ◽  
...  
Keyword(s):  
Wheat Straw ◽  
Environmental Remediation ◽  
Biomass Conversion ◽  
Order Kinetic ◽  
Low Oxygen ◽  
Oxygen Conditions ◽  
Pseudo Second Order ◽  
Physical And Chemical ◽  
Reactive Surfaces ◽  
Best Fit

Contemporary farming practices and rapid industrialization over the last few decades, have raised significant soil and water pollution with extreme toxic effects to humans and ecosystems. The widespread and inefficient use of pesticides, which surpass the soil’s self purification capability, has accelerated soil pollution. In this study, wheat straw biochar was obtained using the traditional pyrolysis technique and its characterization; in addition, the adsorption efficiency of metribuzin was investigated. Biochars’ physical and chemical characteristics were qualified using scanning electron microscopy and Fourier transform infrared spectroscopy. A batch sorption test and liquid chromatography coupled with mass spectrometry were also used to assess the biochar efficiency. SEM and FTIR confirmed the highly reactive surfaces of biochar, establishing efficient biomass conversion in low-oxygen conditions. The adsorption process showed best fit with pseudo second-order kinetic and Langmuir models, suggesting a chemisorption procedure and monolayer-type removal. Regarding its environmental and agricultural application, wheat straw biochar can be advanced as a recommendation solution for further research, which is fundamental for soil rehabilitation and the immobilization of contaminations.

scholarly journals Removal of Lead(II) from Synthetic Wastewater by Lavandula pubescens Decne Biosorbent: Insight into Composition–Adsorption Relationship

2020 ◽  
Vol 10 (21) ◽  
pp. 7450
Author(s):  
Ali Q. Alorabi ◽  
Fahad A. Alharthi ◽  
Mohamed Azizi ◽  
Nabil Al-Zaqri ◽  
Adel El-Marghany ◽  
...  
Keyword(s):  
Ion Concentration ◽  
Wild Plant ◽  
Synthetic Wastewater ◽  
Gas Chromatography Mass Spectrometry ◽  
Gas Liquid Chromatography ◽  
Order Kinetic ◽  
Freundlich Model ◽  
Order Kinetic Model ◽  
Pseudo Second Order ◽  
Best Fit

In this work, the widely-abundant, cheap, wild plant Lavandula pubescens Decne was evaluated as an adsorbent for removing Pb(II) ions from wastewater. The chemical composition of the plant was partially isolated and characterized by the corresponding techniques, including gas chromatography–mass spectrometry, gas liquid chromatography, and FTIR spectroscopy. The adsorption capacity of the dried plant material for Pb(II) ions increased with increasing contact time, initial ion concentration, and temperature, while it decreased with increasing adsorbent dosage. The optimum condition for Pb(II) adsorption was determined as 550 mg/L initial metal concentration, pH ≤ 7, and 90 min of contact. The best fit for Pb(II) adsorption isotherms was the linear form of the Freundlich model; however, the maximum capacity indicated by Langmuir was 91.32 mg/g. The experimental data fit better the pseudo-second-order kinetic model (R2 = 0.969), suggesting chemisorption process. Thermodynamic data revealed an endothermic, nonspontaneous, and adsorption process favored at higher concentrations.

Biodecolorization of Basic Violet 03 Using Biochar Derived from Agricultural Wastes: Isotherm and Kinetics

2020 ◽  
Vol 14 (3) ◽  
pp. 316-326 ◽  
Author(s):  
Josephraj Jegan ◽  
Saravanan Praveen ◽  
Thillainayagam Bhagavathi Pushpa ◽  
Ravindran Gokulan
Keyword(s):  
Binding Capacity ◽  
Maximum Yield ◽  
Agricultural Wastes ◽  
Order Kinetic ◽  
Optimum Conditions ◽  
Batch Mode ◽  
Before And After ◽  
Order Kinetic Model ◽  
Pseudo Second Order ◽  
Best Fit

In the present study, bioremediation of Basic Violet 03 is examined using biochar derived from agricultural wastes. The pyrolytic studies revealed that ideal temperature for maximum yield of biochar derived from Coconut Shell (CSB), Ground nut Shell (GnSB) and Rice Husk (RHB) was obtained as 400 °C, 350 °C and 300 °C respectively. Further from the batch mode of operations, it was concluded that the optimum conditions of biochar dose, pH, temperature and initial concentration are 4 g/L, 8, 40 °C and 75 mg/L with a maximum uptake of 15.79 mg/g, 17.28 mg/g, and 12.64 mg/g for CSB, GnSB and RHB. The adsorption isotherm studies concluded that the three-parameter Sips model was obtained to be the best fit with a maximum correlation coefficient (R2) of 0.9937, 0.9935 and 0.9965. The pseudo second order kinetic model was found to well represent the experimental kinetic data. The characterization results of biochar through SEM, EDX and FTIR revealed that there was a strong binding capacity of adsorbent was observed before and after adsorption process. The promising results concluded that biochar derived from agricultural wastes can potentially be utilized for the removal of cationic dyes.

scholarly journals Mangosteen Peel-Alginate Biocomposite Beads An Efficient and Sustainable Adsorbent For Decontamination of Methylene Blue

2021 ◽  
Author(s):  
Asma Nasrullah ◽  
Amir Sada Khan ◽  
A. H. Bhat ◽  
Taghreed M. Fagieh ◽  
Ersaa M. Bakhsh ◽  
...  
Keyword(s):  
Methylene Blue ◽  
Low Cost ◽  
Cost Effective ◽  
Alginate Beads ◽  
Basic Medium ◽  
Batch Adsorption ◽  
Order Kinetic ◽  
Removal Capacity ◽  
Pseudo Second Order ◽  
Best Fit

Abstract This study examines mangosteen peels waste and alginate beads (MPAB) as an efficient, sustainable and low-cost adsorbent for removal of methylene blue (MB) cationic dye from aqueous solution in a batch adsorption system. Surface functional groups, surface morphology, surface properties, and thermal stability of MBAB were analyzed using various instrumental techniques such as FTIR, FESEM, BET and TGA techniques. MPAB adsorption efficiency for MB was investigated through variation of dosage (0.01- 0.08g), pH (2- 10), contact time (60- 1320 min), MB concentration (20- 100 mg/L) and temperature (298- 333K). MPAB showed maximum removal capacity of 373 mg/g at 25 oC in basic medium. Kinetic and isotherm studies showed that pseudo second order kinetic models and both Freundlich and Langmuir isotherms best fit the experimental data. The findings revealed that novel MPAB has the potential to be a cost-effective adsorbent for removal of textile dyes.

Adsorption of Cr6+ and Pb2+ on soy sauce residue biochar from aqueous solution

BioResources ◽  
2019 ◽  
Vol 14 (2) ◽  
pp. 4653-4669 ◽  
Author(s):  
Xiaoxun Xu ◽  
Chenying Zhou ◽  
Shirong Zhang ◽  
Zhang Cheng ◽  
Zhanbiao Yang ◽  
...  
Keyword(s):  
Heavy Metals ◽  
Pyrolysis Temperature ◽  
Chemical Properties ◽  
Soy Sauce ◽  
Order Kinetic ◽  
Metals Removal ◽  
Initial Ph ◽  
Pseudo Second Order ◽  
Pyrolysis Of Biomass ◽  
Physical And Chemical

Biochar produced by the pyrolysis of biomass can be used to counter water pollution from heavy metals. The purpose of this work was to develop a biosorbent based on soy sauce residue (SSR) for the removal of Cr6+ and Pb2+. The SSR biochar (SBC) from oxygen-limited pyrolysis under the temperatures of 300 to 700 °C were obtained, and their adsorption capability was evaluated. After determining the optimum pyrolysis temperature, the effects of initial pH values, contact times, and initial metal concentrations on the Cr6+ and Pb2+ adsorption by SBC prepared at 600 °C (SBC600) were investigated. With the increase of pyrolysis temperature, the physical and chemical properties of SBC developed in a direction favorable to heavy metal adsorption. The SBC600 reached the adsorption equilibrium at the time of 2 (Cr6+) and 24 h (Pb2+), and the maximum adsorption amounts of Cr6+ and Pb2+ were 25.80 and 135.3 mg/g, respectively. The adsorption kinetics followed the pseudo-second-order kinetic equation, and the adsorption isotherms was best described by the Langmuir isotherms. The SBC was an adsorbent with certain potential for heavy metals removal in wastewater.

scholarly journals Dye removal from aqueous solution by raw maize corncob and H3PO4 activated maize corncob

2017 ◽  
Vol 8 (2) ◽  
pp. 214-224 ◽  
Author(s):  
M. Farnane ◽  
H. Tounsadi ◽  
A. Machrouhi ◽  
A. Elhalil ◽  
F. Z. Mahjoubi ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Order Kinetic ◽  
Solution Ph ◽  
Adsorption Performance ◽  
Adsorption Capacities ◽  
Monolayer Adsorption ◽  
Equilibrium Data ◽  
Order Kinetic Model ◽  
Pseudo Second Order ◽  
Best Fit

AbstractThe focus of this study is the investigation of removal ability of methylene blue (MB) and malachite green (MG) dyes from aqueous solution by raw maize corncob (RMC) and H3PO4 activated maize corncob (AMC). Maize corncobs were carbonized at 500 °C for 2 h, and then impregnated at a phosphoric acid to maize corncob ratio of 2.5 g/g. The impregnated maize corncob was activated in a tubular vertical furnace at 450 °C for 2 h. Samples were characterized by different methods. Adsorption experiments were carried out as a function of solution pH, adsorbent dosage, contact time, initial concentration of dyes and the temperature. Experimental results show that the activation of maize corncob boosts four times the adsorption performance for the selected dyes. The adsorption process is very rapid and was pH dependent with high adsorption capacities in the basic range. The kinetic data were fitted with the pseudo-second-order kinetic model. The best fit of equilibrium data was obtained by the Langmuir model with maximum monolayer adsorption capacities of 75.27 and 271.19 mg/g for MB, 76.42 and 313.63 mg/g for MG, respectively, in the case of RMC and AMC. The temperature did not have much influence on the adsorption performance.

scholarly journals Aqueous Phase Adsorption of Pb (II) Ions onto Hymenoptera sphecidae (Mud-wasp) Nest

2020 ◽  
pp. 21-31
Author(s):  
Donald T. Kukwa ◽  
Peter A. Adie ◽  
Rose E. Kukwa ◽  
Paula D. Kungur
Keyword(s):  
Contact Time ◽  
Low Cost ◽  
Freundlich Isotherm ◽  
Batch Process ◽  
Second Order ◽  
Order Kinetic ◽  
Order Kinetic Model ◽  
Pseudo Second Order ◽  
Best Fit ◽  
Adsorbent Dose

Removal of Pb (II) ion from aqueous solution using Hymenoptera sphecidae (mud-wasp) nest was investigated using a batch process. The effect of pH, contact time and adsorbent dose were also investigated. The result showed that the adsorption of Pb (II) ion onto mud-wasp nest was dependent on pH, contact time and adsorbent dose. Adsorption patterns were analysed in terms of three bi-parameter isotherms of Langmuir, Freundlich and Temkin. Freundlich isotherm gave the best fit to the adsorption data with a correlation coefficient of 0.992, while monolayer sorption capacity yielded 41.667 mg/g. Lagergren’s pseudo first-order and pseudo second-order kinetic models were used to test the adsorption kinetics. The kinetic data were well described by the pseudo second-order kinetic model, suggesting that the process was chemisorption type.  The results showed that mud-wasp nest can be used as a low-cost adsorbent for the removal of Pb (II) ion from aqueous solutions.

scholarly journals Application of Synthetic Layered Sodium Silicate Magadiite Nanosheets for Environmental Remediation of Methylene Blue Dye in Water

2017 ◽  
Author(s):  
Mohamed Mokhtar
Keyword(s):  
Methylene Blue ◽  
Environmental Remediation ◽  
Average Crystallite Size ◽  
Bet Surface Area ◽  
Blue Dye ◽  
Order Kinetic ◽  
Nano Clay ◽  
Order Kinetic Model ◽  
Pseudo Second Order ◽  
Autogenous Pressure

The removal of methylene blue (MB) dye from water was investigated using synthetic nano-clay magadiite (SNCM). SNCM was synthesized by hydrothermal treatment under autogenous pressure. A rosette-shaped single mesoporous magadiite phase with 16.63 nm average crystallite size and 33 m2.g-1 BET-surface area was recorded. The adsorption results indicated the pronounced affinity of the SNCM to the MB dye molecules which reached adsorption uptake of 20.0 mg MB dye/g of SNCM. The elimination of MB dye by the SNCM was kinetically and thermodynamically considered; a pseudo second order kinetic model was attained, and a spontaneous, chemical, and exothermic in nature was verified.

Effect of Zr(IV) to phosphorus ratio on U(VI) adsorption by diethylenetriamine-pentamethylene phosphate Zr(IV) hybrids

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
You-qun Wang ◽  
Huan Wang ◽  
Yue Feng ◽  
Zhi-bin Zhang ◽  
Xiao-hong Cao ◽  
...  
Keyword(s):  
Chemical Properties ◽  
Molar Ratio ◽  
Order Kinetic ◽  
Isothermal Model ◽  
Synthetic Process ◽  
Order Kinetic Model ◽  
Pseudo Second Order ◽  
Ft Ir ◽  
Physical And Chemical ◽  
Contact Angle Analysis

Abstract In this work, diethylenetriamine pentamethylenephosphonic acid (DTPMP) was ultilized into preparing of Zr(IV) organophosphates hybrids (Zr-DTPMP-x, x was the molar ratio of Zr(IV)/DTPMP in the synthetic process, x = 0.5, 1, 2, and 3) using a hydrothermal method. The physical and chemical properties of Zr-DTPMP-x were characterized by SEM&EDS, FT-IR, XRD, Zeta potential, XPS, TGA and contact angle analysis. Moreover, the adsorptive performances of Zr-DTPMP-x for U(VI) were investigated. The adsorption results showed that the optimum molar ratio of Zr(IV) to phosphine, pH, equilibrium time, and dosage was 0.5, 4.0, 180 min, and 10 mg, respectively. Besides, the adsorption of U(VI) was in accordance with the pseudo-second-order kinetic model and Sips isothermal model. Moreover, the adsorption capacity determined by Sips isothermal model was 181.34 mg g−1 for Zr-DTPMP-0.5. Furthermore, the adsorptive selectivity of Zr-DTPMP-0.5 for U(VI) was superior than the others. Zr-DTPMP-0.5 may be a powerful candidate for diminishing the contamination of U(VI).

scholarly journals Optimization of the sorption of selected polycyclic aromatic hydrocarbons by regenerable graphene wool

2019 ◽  
Vol 80 (10) ◽  
pp. 1931-1943 ◽  
Author(s):  
Adedapo O. Adeola ◽  
Patricia B. C. Forbes
Keyword(s):  
Polycyclic Aromatic Hydrocarbons ◽  
Adsorption Capacity ◽  
Aromatic Hydrocarbons ◽  
Kinetic Data ◽  
Second Order ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Polycyclic Aromatic ◽  
Pseudo Second Order ◽  
Best Fit

Abstract A novel graphene wool (GW) material was used as adsorbent for the removal of phenanthrene (PHEN) and pyrene (PYR) from aqueous solution. Adsorption kinetics, adsorption isotherms, thermodynamics of adsorption and effect of pH, ionic strength, and temperature on the adsorption of PHEN and PYR onto GW were comprehensively investigated. Isothermal and kinetic experimental data were fitted to Langmuir, Freundlich, Temkin, Sips and Dubinin–Radushkevich models, as well as pseudo-first-order and pseudo-second-order kinetic models. The adsorption kinetic data best fit the pseudo-second-order kinetic model for PHEN and PYR sorption with R2 value >0.999, whilst the Sips model best fit isotherm data. Kinetic data revealed that 24 hr of contact between adsorbent and polycyclic aromatic hydrocarbons (PAHs) was sufficient for maximum adsorption, where the Langmuir maximum adsorption capacity of GW for PHEN and PYR was 5 and 20 mg g−1 and the optimum removal efficiency was 99.9% and 99.1%, respectively. Thermodynamic experiments revealed that adsorption processes were endothermic and spontaneous. Desorption experiments indicated that irreversible sorption occurred with a hysteresis index greater that zero for both PAHs. The high adsorption capacity and potential reusability of GW makes it a very attractive material for removal of hydrophobic organic micro-pollutants from water.

scholarly journals Synthesis of cross-linking chitosan-PVA composite hydrogel and adsorption of Cu(II) ions

2020 ◽  
Vol 81 (5) ◽  
pp. 1063-1070 ◽  
Author(s):  
Qingping Song ◽  
Jiangang Gao ◽  
Ying Lin ◽  
Ze Zhang ◽  
Yixin Xiang
Keyword(s):  
Chemical Properties ◽  
Acid Resistance ◽  
Strong Acid ◽  
Order Kinetic ◽  
X Ray Diffraction ◽  
Ion Removal ◽  
Order Kinetic Model ◽  
Pseudo Second Order ◽  
Ph Range ◽  
Physical And Chemical

Abstract A cross-linked chitosan-PVA spherical hydrogel (CSH) was synthesized and its structure was characterized by Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM) and X-ray diffraction (XRD). The physical and chemical properties of CSH, such as acid resistance and swelling, were determined. Finally, Cu(II) ion removal by the CSH was investigated, and the effects of experimental parameters, including pH, adsorption time, and regeneration performance were examined. Results revealed that CSH has outstanding stability in strong acid solution, thus extending the useful pH range as an adsorbent material. The maximum capacity of CSH for Cu(II) was obtained to be 62.1 mg/g at 25 °C for 24 h. The adsorption process was best described by a pseudo-second-order kinetic model, while isotherm modeling revealed that the Langmuir equation better described the adsorption of Cu(II) on CSH. Moreover, the loaded CSH can be easily regenerated by the HCl-washing method and reused repeatedly for Cu(II) adsorption for up to five cycles.

Sign in / Sign up

Export Citation Format

Share Document