scholarly journals Synthesis of Ambient Cured GGBFS Based Alkali Activated Binder Using a Sole Alkaline Activator: A Feasibility Study

2021 ◽  
Vol 11 (13) ◽  
pp. 5887
Author(s):  
Thandiwe Sithole ◽  
Nelson Tsotetsi ◽  
Tebogo Mashifana
Keyword(s):  
Silicate Solution ◽  
Environmental Footprint ◽  
Ambient Temperatures ◽  
Granulated Blast Furnace Slag ◽  
Naoh Solution ◽  
Alkaline Activator ◽  
Porous Morphology ◽  
Furnace Slag ◽  
Alkali Activated

Utilisation of industrial waste-based material to develop a novel binding material as an alternative to Ordinary Portland Cement (OPC) has attracted growing attention recently to reduce or eliminate the environmental footprint associated with OPC. This paper presents an experimental study on the synthesis and evaluation of alkali activated Ground granulated blast furnace slag (GGBFS) composite using a NaOH solution as an alkaline activator without addition of silicate solution. Different NaOH concentrations were used to produce varied GGBFS based alkali activated composites that were evaluated for Uncofined Compressive Strength (UCS), durability, leachability, and microstructural performance. Alkali activated GGBFS composite prepared with 15 M NaOH solution at 15% L/S ratio achieved a UCS of 61.43 MPa cured for 90 days at ambient temperatures. The microstructural results revealed the formation of zeolites, with dense and non-porous morphology. Alkali activated GGBFS based composites can be synthesized using a sole alkaline activator with potential to reduce CO2 emission. The metal leaching tests revealed that there are no potential environmental pollution threats posed by the synthesized alkali activated GGBFS composites for long-term use.

scholarly journals Microstructure Features of Ternary Alkali-activated Binder Based on Tungsten Mining Waste, Slag and Metakaolin

2020 ◽  
Author(s):  
Naim Sedira ◽  
João Castro-Gomes
Keyword(s):  
Sodium Silicate ◽  
Room Temperature ◽  
Mining Waste ◽  
Dense Matrix ◽  
Microstructural Properties ◽  
Reaction Products ◽  
Granulated Blast Furnace Slag ◽  
Alkaline Activator ◽  
Furnace Slag ◽  
Alkali Activated

This study determines the effect of ground granulated blast furnace slag (GGBFS) and metakaolin (MK) on the microstructural properties of the tungsten mining waste-based alkali-activated binder (TMWM). During this investigation, TMWM was partially replaced with 10 wt.% GGBFS and 10 wt.% MK to improve the microstructure of the binder. In order to understand the effect of the substitutions on the microstructure, two pastes were produced to make a comparative study between the sample contain 100% TMWM and the ternary precursors. Both precursors were activated using a combination of alkaline activator solutions (sodium silicate and sodium hydroxide) with the ratio of 1:3 (66.6 wt.% sodium silicate combined with 33.33 wt.% of NaOH 8M). The alkali-activated mixes were cured in oven at temperature of 60 °C in the first day and at room temperature for the next 27 days. The reaction products N-A-S-H gel and (N,M)-A-S-H gel resulted from the alkaline activation reaction process. In addition, a formation of natrite (Na2CO3) with needles shape occurred as a reaction product of the fluorescence phenomena. However, a dense matrix resulted from the alkline activation of the ternary precursors containg different gels such as N-A-S-H, C-A-S-H and (N,M)-C-A-S-H gel, these results were obtained through SEM-EDS analyses, as well FTIR tests. Keywords: Mining Waste, Alkali-activated, Microstructure, Slag, Metakaolin

scholarly journals Effects of Composition Type and Activator on Fly Ash-Based Alkali Activated Materials

Polymers ◽  
2021 ◽  
Vol 14 (1) ◽  
pp. 63
Author(s):  
Chan-Yi Lin ◽  
Tai-An Chen
Keyword(s):  
Fly Ash ◽  
Sodium Hydroxide ◽  
Blast Furnace Slag ◽  
Raw Material ◽  
Granulated Blast Furnace Slag ◽  
Different Types ◽  
Short And Long Term ◽  
Furnace Slag ◽  
Alkali Activated

The compressive strengths of fly ash-based alkali-activated materials (AAM), produced using various activators of only sodium hydroxide, were measured. Fly ash-based AAM specimens, produced by mixing different kinds of fly ash and ground granulated blast-furnace slag (GGBFs) with an activator containing only sodium hydroxide, were cured at ambient temperature, and then placed in air for different numbers of days. The short- and long-term compressive strengths and shrinkage of fly ash-based AAM were measured and compared to one another. The effects of type of fly ash, alkali-equivalent content, GGBFs replace percentage, and ages on the compressive strengths and shrinkage of fly ash-based AAM were investigated. Even when different fly ash was used as the raw material for AAM, a similar compressive strength can be achieved by alkali-equivalent content, GGBFs replaces percentage. However, the performance of shrinkage due to different types of fly ash differed significantly.

Effect of the Combined Using of Fly Ash and Granulated Blast Furnace Slag on Properties of Cementless Alkali-Activated Mortar

2011 ◽  
Vol 287-290 ◽  
pp. 916-921
Author(s):  
Kyung Taek Koh ◽  
Gum Sung Ryu ◽  
Si Hwan Kim ◽  
Jang Hwa Lee
Keyword(s):  
Compressive Strength ◽  
Blast Furnace ◽  
Fly Ash ◽  
Blast Furnace Slag ◽  
Curing Temperature ◽  
Mixture Ratio ◽  
Granulated Blast Furnace Slag ◽  
Alkaline Activator ◽  
Furnace Slag ◽  
Alkali Activated

This paper examines the effects of the mixture ratio of fly ash/slag, the type of alkaline activators and curing conditions on the workability, compressive strength and microstructure of cementless alkali-activated mortar. The investigation showed that the mixture ratio of fly ash/slag and the type of alkaline activator have significant influence on the workability and strength, whereas the curing temperature has relatively poor effect. An alkali-activated mortar using a binder composed of 50% of fly ash and 50% of granulated blast furnace slag and alkaline activator made of 9M NaOH and sodium silicate in proportion of 1:1 is seen to be able to develop a compressive strength of 65 MPa at age of 28 days even when cured at ambient temperature of 20°C.

scholarly journals Effect of alkali cation type on the plasticizing effect of ligno-sulfonate in alkali-activated systems

2021 ◽  
Vol 1205 (1) ◽  
pp. 012016
Author(s):  
V Iliushchenko ◽  
V Bilek Jr. ◽  
L Kalina ◽  
P Hruby ◽  
T Opravil ◽  
...  
Keyword(s):  
Rheological Properties ◽  
Blast Furnace Slag ◽  
Dry Matter ◽  
Oscillation Amplitude ◽  
Granulated Blast Furnace Slag ◽  
Cation Type ◽  
Alkaline Activator ◽  
Furnace Slag ◽  
Alkali Activated ◽  
Slag Weight

Abstract The rheological properties of alkali-activated systems are significantly affected by the nature of the alkaline activator. Hydroxide-activated systems’ workability is typically lower than that of alkali-activated systems but can be improved by lignosulfonate plasticizer. However, the lignosulfonate plasticizer’s effectivity depends on the dosage of lignosulfonate, the nature of hydroxide and pH of their solutions. Therefore, in this study, the effectiveness of lignosulfonate plasticizer with respect to alkali ion type (Na+, K+, Li+) in alkali hydroxide-activated systems based on ground granulated blast furnace slag was evaluated. The concentration of the alkaline activator (NaOH, KOH and LiOH) was the same in all cases of 4M. The superplasticizer dosage was 0%, 0.5% and 1.0% of dry matter of lignosulfonate plasticizer to the slag weight. Rheological properties were determined using a rotational rheometer equipped with vane in-cup geometry working in oscillation amplitude sweep mode, from which critical strain and corresponding viscoelastic variables were obtained.

scholarly journals Statistical Evaluation of Mechanical Properties of Slag Based Alkali-Activated Material

2019 ◽  
Vol 11 (21) ◽  
pp. 5935 ◽  
Author(s):  
Martin Sisol ◽  
Dušan Kudelas ◽  
Michal Marcin ◽  
Tomáš Holub ◽  
Peter Varga
Keyword(s):  
Industrial Wastes ◽  
Sustainable Construction ◽  
Industrial Processing ◽  
Granulated Blast Furnace Slag ◽  
Strength Tests ◽  
Alkaline Activator ◽  
Solution Parameters ◽  
Furnace Slag ◽  
By Products ◽  
Alkali Activated

Slag is one of the by-products of the energy industry, which is suitable for secondary industrial processing. Although slag has been successfully used in industrial production for several decades, its use does not achieve the level of its potential. Today, to achieve a sustainable construction industry, alternative types of cement have been extensively investigated. Geopolymer is a kind of material which is obtained from the alkaline activator and it can be produced from the industrial wastes or by-products. In this study, SiO2/Na2O ratio and the amount of Na2O in activation solution parameters of alkali-activated materials were tested how they affect the strengths of hardened geopolymers from ground granulated blast furnace slag (GGBFS). Compressive and flexural strength tests were conducted, and the results were analyzed by analysis of variance (ANOVA). Strengths were tested after 7, 28, and 90 days.

scholarly journals Red Mud-Blast Furnace Slag-Based Alkali-Activated Materials

2021 ◽  
Vol 13 (20) ◽  
pp. 11298
Author(s):  
Alessio Occhicone ◽  
Mira Vukčević ◽  
Ivana Bosković ◽  
Claudio Ferone
Keyword(s):  
Compressive Strength ◽  
Blast Furnace ◽  
Red Mud ◽  
Blast Furnace Slag ◽  
Bauxite Residue ◽  
Sodium Silicate Solution ◽  
Silicate Solution ◽  
Waste Products ◽  
Furnace Slag ◽  
Alkali Activated

The aluminum Bayer production process is widespread all over the world. One of the waste products of the Bayer process is a basic aluminosilicate bauxite residue called red mud. The aluminosilicate nature of red mud makes it suitable as a precursor for alkali-activated materials. In this work, red mud was mixed with different percentages of blast furnace slag and then activated by sodium silicate solution at different SiO2/Na2O ratios. Obtained samples were characterized by chemical–physical analyses and compressive strength determination. Very high values of compressive strength, up to 50 MPa, even for high percentage of red mud in the raw mixture (70 wt.% of RM in powder mixture), were obtained. In particular, the higher compressive strength was measured for cubic samples containing 50 wt.% of RM, which showed a value above 70 MPa. The obtained mixtures were characterized by no or scarce environmental impact and could be used in the construction industry as an alternative to cementitious and ceramic materials.

Alkali-Activated EAF Reducing Slag as Binder for Concrete

2013 ◽  
Vol 723 ◽  
pp. 580-587
Author(s):  
Wen Huan Zhong ◽  
Tung Hsuan Lu ◽  
Wei Hsing Huang
Keyword(s):  
Portland Cement ◽  
Drying Shrinkage ◽  
Portland Cement Concrete ◽  
Steel Making ◽  
Chemical Content ◽  
Alkaline Activator ◽  
Furnace Slag ◽  
Alkali Activated ◽  
Better Than

Electric arc furnace (EAF) reducing slag is the by-product of EAF steel-making. Currently, reducing slag is considered a waste material by the industry in Taiwan. Since the chemical content of reducing slag is similar to blast furnace slag (BFS), it is expected that reducing slag exhibits a similar pozzolanic effect as the BFS. This study used alkaline activator consisting of sodium silicate and sodium hydroxide to improve the activity of reductive slag so as to replace Portland cement as binder in concrete. Some BFS was used to blend with the reducing slag to enhance the binding quality of alkali-activated mixes. The results show that a blend of 50% BFS and 50% reducing slag can be activated successively with alkali. Also, the sulfate resistance of concrete made with alkali-activated EAF reducing slag is found to be better than that of concrete made with portland cement, while the drying shrinkage of alkali-activated EAF reducing slag concrete is greater than that of portland cement concrete.

scholarly journals The efficiency of plasticizing surfactants in alkali-activated cement mortars and concretes

2018 ◽  
Vol 230 ◽  
pp. 03016 ◽  
Author(s):  
Raisa Runova ◽  
Volodymyr Gots ◽  
Igor Rudenko ◽  
Oleksandr Konstantynovskyi ◽  
Oles’ Lastivka
Keyword(s):  
Compressive Strength ◽  
Blast Furnace Slag ◽  
Chemical Nature ◽  
Granulated Blast Furnace Slag ◽  
Cement Mortars ◽  
Alkaline Component ◽  
Property Modification ◽  
Furnace Slag ◽  
Alkali Activated ◽  
Strength In Bending

Functionality of mortar and concrete mixes is regulated by surfactants, which act as plasticizers. The molecular structure of these admixtures can be changed during hydration of alkali-activated cements (AAC). The objective was to determine the chemical nature of plasticizers effective for property modification of mortars and concretes based on AACs with changing content of granulated blast furnace slag from 0 to 100 %. The admixtures without ester links become more effective than polyesters when content of alkaline component increase. The admixtures effective in high alkaline medium were used in dry mixes for anchoring (consistency of mortar 150 mm by Vicat cone; 1 d tensile strength in bending / compressive strength of mortar 6.6 /30.6 MPa) and in ready-mixed concretes (consistency class changed from S1 to S3, S4 with consistency safety during 60 min; 3 d compressive strength of modified concrete was not less than the reference one without admixtures).

scholarly journals Pressure-Induced Geopolymerization in Alkali-Activated Fly Ash

2018 ◽  
Vol 10 (10) ◽  
pp. 3538 ◽  
Author(s):  
Sol Park ◽  
Hammad Khalid ◽  
Joon Seo ◽  
Hyun Yoon ◽  
Hyeong Son ◽  
...  
Keyword(s):  
Fly Ash ◽  
Sodium Hydroxide ◽  
Sodium Silicate ◽  
Sodium Silicate Solution ◽  
Silicate Solution ◽  
Elevated Pressure ◽  
X Ray Diffraction ◽  
27Al Mas Nmr ◽  
Alkali Activated

The present study investigated geopolymerization in alkali-activated fly ash under elevated pressure conditions. The fly ash was activated using either sodium hydroxide or a combination of sodium silicate solution and sodium hydroxide, and was cured at 120 °C at a pressure of 0.22 MPa for the first 24 h. The pressure-induced evolution of the binder gel in the alkali-activated fly ash was investigated by employing synchrotron X-ray diffraction and solid-state 29Si and 27Al MAS NMR spectroscopy. The results showed that the reactivity of the raw fly ash and the growth of the zeolite crystals were significantly enhanced in the samples activated with sodium hydroxide. In contrast, the effects of the elevated pressure conditions were found to be less apparent in the samples activated with the sodium silicate solution. These results may have important implications for the binder design of geopolymers, since the crystallization of geopolymers relates highly to its long-term properties and functionality.

Sign in / Sign up

Export Citation Format

Share Document