scholarly journals Effect of Structure and Chemical Activation on the Adsorption Properties of Green Clay Minerals for the Removal of Cationic Dye

2018 ◽  
Vol 8 (11) ◽  
pp. 2302 ◽  
Author(s):  
Abdelfattah Amari ◽  
Hatem Gannouni ◽  
Mohammad Khan ◽  
Mohammed Almesfer ◽  
Abubakr Elkhaleefa ◽  
...  
Keyword(s):  
Clay Minerals ◽  
Pore Volume ◽  
Acid Treatment ◽  
Structural Changes ◽  
Chemical Activation ◽  
Total Pore Volume ◽  
Batch Adsorption ◽  
Acid Activation ◽  
Cationic Dye ◽  
Average Pore

In this study, natural clay minerals with green appearance were treated with sulfuric acid. Mass percentage of acid (wt%), temperature (T), contact time (t) and liquid-to-solid mass ratio (R) are used as the prevailing factors that determine the extent of acid-activation. The values of these factors range from 15–50%, 60–90 °C, 1.5–6 h and 4–7, respectively. The study has focused on the structural changes as well as textural characteristics of the clay. Three activated clay samples were prepared under different treatment conditions. The samples were characterized using X-ray powder diffraction (XRD), fourier transform infrared (FTIR), scanning electron microscope (SEM), chemical analysis and N2 adsorption techniques. Characterization of the treated clay minerals exhibited significant structural changes to a greater extent of acid-activation, from being partially crystalline to being amorphous silica. The surface area and total pore volume of clay increased proportionally with the level of acid treatment. The average pore diameter behaved differently. During the strong acid treatment, a large increase in pore volume and the enlargement of the pore size distribution were observed. This suggests that considerable structural changes and partial destruction may have occurred in this condition. The removal of methylene blue, used as cationic dye, from aqueous solution by the batch adsorption technique on three prepared acid-activated clay samples was studied. The Langmuir model was found to agree well with the experimental data.

scholarly journals Single and competitive adsorption of Cd(II) and Pb(II) from aqueous solution by activated carbon prepared with Salix matsudana Kiodz

2016 ◽  
Vol 74 (12) ◽  
pp. 2751-2761 ◽  
Author(s):  
Yan Shu ◽  
Kelin Li ◽  
Jinfeng Song ◽  
Bing Li ◽  
Chunfang Tang
Keyword(s):  
Activated Carbon ◽  
Ph Value ◽  
Total Pore Volume ◽  
Maximum Adsorption Capacity ◽  
Single Element ◽  
Acid Activation ◽  
Adsorption Model ◽  
Adsorption Selectivity ◽  
Average Pore ◽  
Salix Matsudana

In this study, Salix matsudana activated carbon (SAC) was prepared by phosphoric acid activation, and the adsorption characteristics of Cd(II) and Pb(II) on SAC in single- and double-component solutions were investigated. In both systems, the adsorption capacities of both ions on SAC increased with the increasing initial pH value and temperature in the solutions, and the adsorption equilibrium was approached at 10 min. The adsorption process was spontaneous, endothermic, and depicted well by the pseudo-second-order adsorption model, and the equilibrium adsorption fitted reasonably well with the Langmuir isotherm. The maximum adsorption capacity (Qm) of Cd(II) and Pb(II) was 58.48 and 59.01 mg/g, respectively, in the single-element systems. However, it reduced to 25.32 and 31.09 mg/g, respectively, in the double-element system. The physicochemical property analysis showed that the specific surface area, total pore volume, and average pore diameter of SAC was 435.65 m2/g, 35.68 mL/g, and 3.86 nm, respectively. The SAC contained groups of -OH, C = O, and P = O. Results suggest that SAC had a good performance for the adsorption of Cd(II) and Pb(II) from solution, and the adsorption selectivity sequence was Pb(II) > Cd(II).

scholarly journals The Production and Characterization of Activated Carbon Electrodes from Pineapple Leaf Fibers for Supercapacitor Application

2020 ◽  
Vol 9 (1) ◽  
pp. 1-8
Author(s):  
Agustino Agustino ◽  
Rakhmawati Farma ◽  
Erman Taer
Keyword(s):  
Activated Carbon ◽  
Chemical Activation ◽  
Total Pore Volume ◽  
Amorphous Structure ◽  
Physical Activation ◽  
Carbon Electrode ◽  
Average Pore ◽  
Average Pore Radius ◽  
Supercapacitor Application

Elektroda karbon aktif berbasis serat daun nanas (SDN) telah berhasil diproduksi dengan proses tiga langkah berikut ini, yaitu: (i) aktivasi kimia, (ii) karbonisasi, dan (iii) aktivasi fisika. Aktivasi kimia dilakukan dengan menggunakan agen pengaktif KOH dengan konsetrasi 0,3 M. Karbonisasi dilakukan dalam lingkungan gas N2 pada temperatur 600oC dan diikuti oleh aktivasi fisika pada temperatur 850oC menggunakan gas CO2 selama 2,5 jam. Luas permukaan spesifik elektroda 512,211 m2×g-1 dengan volume total pori sebesar 0,093 cm3×g–1, dan jari-jari pori rata-rata 1,199 nm. Morfologi permukaan elektroda karbon aktif menunjukkan adanya serat karbon dengan diameter serat dalam kisaran 101 - 185 nm dan memliki kandungan karbon dengan massa atomik sebesar 84,33%. Elektroda karbon aktif memiliki struktur amorf, yang ditunjukkan oleh dua puncak difraksi yang lebar pada sudut hamburan 24,64 dan 43,77o yang bersesuaian dengan bidang (002) dan (100). Kapasitansi spesifik, energi spesifik dan daya spesifik sel superkapasitor yang dihasilkan masing-masing sebesar 110 F×g-1, 15,28 Wh×kg-1 dan 36,69 W×kg-1. Pineapple leaf fiber (PALF) based activated carbon electrode has been successfully produced using three-step process, i.e. (i) chemical activation, (ii) carbonization, and (iii) physical activation. The chemical activation was carried out using KOH activating agent with a concentration of 0.3 M. The carbonization process is conducted out in N2 gas environment at 600oC and followed by physical activation at a temperature of 850oC by using CO2 gas for 2.5 h. The specific surface area of the electrode is 512.211 m2×g-1 with a total pore volume of 0.093 cm3×g-1, and average pore radius of 1.199 nm. The surface morphology of the electrode shown the carbon fibers with diameter in the range of 101 - 185 nm and carbon content with 84.33% of atomic mass. The activated carbon electrode has an amorphous structure, which is shown by two wide diffraction peaks at scattering angles of 24.64 and 43.77o which correspond to the plane (002) and (100), respectively. The specific capacitance, energy and power of the electrode are 110 F×g-1, 15.28 Wh×kg-1 and 36.69 W×kg-1, respectively.Keywords: Serat daun nanas, Kalium hidroksida, Elektroda karbon aktif, Kapasitansi spesifik, Superkapasitor 

scholarly journals On the Gas Storage Properties of 3D Porous Carbons Derived from Hyper-Crosslinked Polymers

Polymers ◽  
2019 ◽  
Vol 11 (4) ◽  
pp. 588 ◽  
Author(s):  
Giorgio Gatti ◽  
Mina Errahali ◽  
Lorenzo Tei ◽  
Maurizio Cossi ◽  
Leonardo Marchese
Keyword(s):  
Thermal Treatment ◽  
Surface Area ◽  
Pore Volume ◽  
Chemical Activation ◽  
Chemical Characterization ◽  
Total Pore Volume ◽  
Textural Properties ◽  
Gas Storage ◽  
Bet Surface Area ◽  
Porous Carbons

The preparation of porous carbons by post-synthesis treatment of hypercrosslinked polymers is described, with a careful physico-chemical characterization, to obtain new materials for gas storage and separation. Different procedures, based on chemical and thermal activations, are considered; they include thermal treatment at 380 °C, and chemical activation with KOH followed by thermal treatment at 750 or 800 °C; the resulting materials are carefully characterized in their structural and textural properties. The thermal treatment at temperature below decomposition (380 °C) maintains the polymer structure, removing the side-products of the polymerization entrapped in the pores and improving the textural properties. On the other hand, the carbonization leads to a different material, enhancing both surface area and total pore volume—the textural properties of the final porous carbons are affected by the activation procedure and by the starting polymer. Different chemical activation methods and temperatures lead to different carbons with BET surface area ranging between 2318 and 2975 m2/g and pore volume up to 1.30 cc/g. The wise choice of the carbonization treatment allows the final textural properties to be finely tuned by increasing either the narrow pore fraction or the micro- and mesoporous volume. High pressure gas adsorption measurements of methane, hydrogen, and carbon dioxide of the most promising material are investigated, and the storage capacity for methane is measured and discussed.

Effect of Heat-Treatment in Ar Atmosphere on Pore Structure of Carbonaceous Materials from Polysiloxane

2014 ◽  
Vol 602-603 ◽  
pp. 279-284
Author(s):  
Li Qun Duan ◽  
Chen Chen Zhang ◽  
Qing Song Ma ◽  
Zhao Hui Chen
Keyword(s):  
Heat Treatment ◽  
Pore Structure ◽  
Pore Size ◽  
Pore Volume ◽  
Average Pore Size ◽  
Total Pore Volume ◽  
Treatment Temperature ◽  
Carbonaceous Materials ◽  
Average Pore ◽  
Pore Size Distributions

Nanoporous carbonaceous materials derived from polysiloxane were first prepared by pyrolysis at 1300°C followed with hydrofluoric acid (HF) etching treatment. Their thermal stability of pore structure in inert condition was investigated in this paper by nitrogen adsorption technique in detail. The specific surface area (SSA) and pore volume (total pore volume, micropore volume, mesopore volume) decreased continually in the heat-treatment temperature range of 1000~1400°C. The average pore size almost kept the same with the raw sample. However, when the temperature exceeded 1400°C, the micropore interconnection began transforming to mesopore structure, which led to the decline of SSA and the increase of average pore size. Furthermore, the pore size distributions (PSDs) curves showed that heat-treatment had an advantage on the transition process of pore structure from disorder to regularity to some extent when heat-treated in the range 1000~1400°C for the most possible reason of relief of residue strain in the carbonaceous materials.

Optimization of Experimental Conditions for the Preparation of High Specific Surface Area Bamboo-Based Activated Carbon

2015 ◽  
Vol 1090 ◽  
pp. 154-159
Author(s):  
Sheng Zhou Zhang ◽  
Hong Ying Xia ◽  
Li Bo Zhang ◽  
Jin Hui Peng ◽  
Jian Wu ◽  
...  
Keyword(s):  
Activated Carbon ◽  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Pore Volume ◽  
Total Pore Volume ◽  
High Specific Surface Area ◽  
Raw Material ◽  
Experimental Conditions ◽  
Average Pore

Bamboo as the raw material is carbonized to prepare high specific surface area activated carbon by microwave heating under nitrogen atmosphere in our present work. Influences of activation agents on the preparation of activated carbon are studied. The results show that activation agents have a significant influence on the preparation of activated carbon. Under the heating time of 15 min, the adsorption capacity of the activated carbon prepared utilizing KOH as activation agent is the best. When the KOH/C ratio is 4, the iodine number and yield of activated carbon are 2298 mg/g and 39.82%, respectively. The BET specific surface area, total pore volume and average pore diameter of activated carbon are 3441 m2/g, 2.093 ml/g and 2.434 nm, respectively. The micropore volume of 1.304 ml/g is 62.30% of total pore volume, indicating that the activated carbon is microporous activated carbon.

Experimental Research on the Preparation of Porous Activated Carbon from Orange Wastes

2009 ◽  
Vol 79-82 ◽  
pp. 1907-1910
Author(s):  
Zhi Gang Xie
Keyword(s):  
Activated Carbon ◽  
Surface Area ◽  
Pore Volume ◽  
Pore Diameter ◽  
Total Pore Volume ◽  
Carbonization Temperature ◽  
Bet Surface Area ◽  
Average Pore ◽  
Impregnation Ratio ◽  
Heat Preservation

Porous activated carbon was prepared from orange wastes using zinc chloride as an activating agent by one-step carbonization method. Effects of impregnation ratio, carbonization temperature and heat preservation time on pore characteristics of activated carbon were studied. The porous structures of the orange wastes activated carbon were investigated by BET, D-R equations, BJH equations and Kelvin theory. The morphology was observed using transmission electron microscopy (TEM). The mesoporous activated carbon is gained when the impregnation ratio is 3:1; the carbonization temperature is 550°Cand heat preservation time is 1.0 h. The activated carbon has total pore volume 2.098 cm3/g, mesoporous pore volume 1.438 cm3/g, with a high BET surface area 1476m2/g. The pore distribution of the mesoporous activated carbon is very concentrative, with average pore diameter of 3.88nm. While, the high specific surface area activated carbon is gained when the impregnation ratio is 2:1; the carbonization temperature is 550°Cand heat preservation time is 1.0 h. The activated carbon has high BET surface area 1909 m2/g, while the total pore volume is only 1.448cm3/g and microporous pore volume is 0.889cm3/g, with average pore diameter of 2.29 nm.

scholarly journals Possibilities of Graphitization of Unburned Carbon from Coal Fly Ash

Minerals ◽  
2021 ◽  
Vol 11 (9) ◽  
pp. 1027
Author(s):  
Zdzisław Adamczyk ◽  
Joanna Komorek ◽  
Barbara Białecka ◽  
Joanna Całus-Moszko ◽  
Agnieszka Klupa
Keyword(s):  
Fly Ash ◽  
Pore Volume ◽  
Pore Diameter ◽  
Coal Fly Ash ◽  
Total Pore Volume ◽  
Starting Material ◽  
Unburned Carbon ◽  
Active Carbons ◽  
Average Pore ◽  
Graphite Phase

The paper presents the characteristics of products annealing at the temperatures of 2400 and 3000 °C of unburned carbon from coal fly ash in terms of its possible use as a starting material in the graphitization process. An amorphous substance (organic substance) with an admixture of some minerals has been found in samples subjected to graphitization. However, the graphite phase is dominant in products subjected to graphitization. Studies have also shown a diverse grain morphology in individual samples. The presence of plate-shaped and tube-shaped grains was found. As the graphitization temperature of the starting material increases (2400 and 3000 °C), the specific surface area in the graphitization products decreases. The total pore volume in the samples after the graphitization process was significantly lower than the pore volume of active carbons produced from other unburned carbon. Average pore diameter is similar to the pore diameter in active carbons. The reflectance value of the matrix for the sample graphitized at 3000 °C is characteristic for graphite. Unburned carbon from Polish fly ash can be used as the starting material for graphitization.

Experimental Study of the Pore Structure Characterization in Shale With Different Particle Size

2018 ◽  
Vol 140 (5) ◽  
Author(s):  
Shuwen Zhang ◽  
Xuefu Xian ◽  
Junping Zhou ◽  
Guojun Liu ◽  
Yaowen Guo ◽  
...  
Keyword(s):  
Particle Size ◽  
Specific Surface ◽  
Pore Structure ◽  
Pore Volume ◽  
Gas Adsorption ◽  
Total Pore Volume ◽  
Structure Characterization ◽  
Particle Sizes ◽  
Average Pore ◽  
Longmaxi Shale

In order to study the effects of particle size on the determination of pore structure in shale, the outcrop of Ordovician Wufeng (WF) and Silurian Longmaxi shale (LMX) samples from Sichuan basin were chosen and crushed into various particle sizes. Then, pore structure was analyzed by using low-pressure gas adsorption (LPGA) tests. The results show that the pore of shales is mainly composed of slit-type pores and open pores. The specific surface areas of shale are mainly contributed by micropores, while the largest proportion of the total pore volume in shale is contributed by mesopores. With the decreasing of particle size, the specific surface area of both samples is decreased, while average pore diameter and the total pore volume are increased gradually. The influences of particle size on the pore structure parameters are more significant for micropore and macropore, as the particle sizes decrease from 2.36 mm to 0.075 mm, the volume of micropores in Longmaxi shale increases from 0.283 cm3/100 g to 0.501 cm3/100 g with an increment almost 40%, while the volume of macropores decreases from 0.732 cm3/100 g to 0.260 cm3/100 g with a decrement about 50%. This study identified the fractal dimensions at relative pressures of 0–0.50 and 0.50–0.995 as D1 and D2, respectively. D1 increases with the decrease of particle size of shale, while D2 shows an opposite tendency in both shale samples.

scholarly journals THE STABILIZING OF ANATASE AEROGEL AT HIGH TEMPERATURE

2010 ◽  
Vol 4 (2) ◽  
pp. 110-116 ◽  
Author(s):  
Silvester Tursiloadi ◽  
Hiroshi Hirashima
Keyword(s):  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Pore Volume ◽  
Anatase Phase ◽  
Total Pore Volume ◽  
Average Pore ◽  
Amorphous Sio2 ◽  
Bet Specific Surface Area ◽  
Sio2 Aerogel

Stable anatase is attractive to its notable functions for photo catalysis and photon-electron transfer.   Stable anatase TiO­2 containing amorphous SiO2 aerogel was prepared by hydrolysis of Ti (OC3H7)4 and Si (OC3H7)4 in a 2-propanol solution with acid catalyst. The solvent in wet gels was supercritically extracted in CO2 at 60 oC and 22 Mpa. Thermal evolutions of the microstructure of the gels were evaluated by TGA-DTA, N2 adsorption and XRD. A stable anatase TiO2 containing amorphous SiO2 aerogel with a BET specific surface area of 365 m2/g and a total pore volume of 0.20 cm3/g was obtained as prepared condition. The anatase phase was stable after calcination up to 1000 oC, and BET specific surface area, total pore volume and average pore diameter did not change significantly after calcination up to 900 oC.   Keywords: Supercritical extraction, sol-gel, aerogel, stable anatase structure

scholarly journals Fractal Characteristics and Heterogeneity of the Nanopore Structure of Marine Shale in Southern North China

Minerals ◽  
2019 ◽  
Vol 9 (4) ◽  
pp. 242 ◽  
Author(s):  
Yu ◽  
Ju ◽  
Qi ◽  
Qiao ◽  
Huang ◽  
...  
Keyword(s):  
Pore Volume ◽  
North China ◽  
Average Pore Size ◽  
Fractal Dimensions ◽  
Total Pore Volume ◽  
Integrated Approach ◽  
Bet Surface Area ◽  
Average Pore ◽  
Marine Shale ◽  
Nanopore Structure

The characteristics of the nanopore structure in shale play a crucial role in methane adsorption and in determining the occurrence and migration of shale gas. In this study, using an integrated approach of X-ray diffraction (XRD), N2 adsorption, and field emission scanning electron microscopy (FE-SEM), we systematically focused on eight drilling samples of marine Taiyuan shale from well ZK1 in southern North China to study the characteristics and heterogeneity of their nanopore structure. The results indicated that different sedimentary environments may control the precipitation of clay and quartz between transitional shale and marine shale, leading to different organic matter (OM)–clay relationships and different correlations between total organic carbon (TOC) and mineral content. The shale with high TOC content tended to have more heterogeneous micropores, leading to a higher fractal dimension and a more complex nanopore structure. With the increase of TOC content and thermal evolution of OM, the heterogeneity of the pore structure became more significant. Quartz from marine shale possessed abundant macropores, resulting in a decrease of the Brunauere–Emmette–Teller (BET (BET) surface area (SA) and an increase of the average pore size (APS), while clay minerals developed a large number of micropores which worked together with OM to influence the nanopore structure of shale, leading to the increase of the SA and the decrease of the APS. The spatial order of interlayer pores increased with the increase of mixed-layer illite–smectite (MLIS) content, which naturally reduced the fractal dimensions. In contrast, kaolinite, chlorite, and illite have a small number of nanopores, which might enhance the complexity and reduce the connectivity of the nanopore system by mean of pore-blocking. Taiyuan shale with higher heterogeneity is highly fractal, and its fractal dimensions are principally related to the micropores. The fractal dimensions correlate positively with the SA and total pore volume, suggesting that marine shale with higher heterogeneity may possess a larger SA and a higher total pore volume.

Sign in / Sign up

Export Citation Format

Share Document