scholarly journals Wear Resistance of Aluminum Matrix Composites’ Coatings Added on AA6082 Aluminum Alloy by Laser Cladding

Coatings ◽  
2021 ◽  
Vol 12 (1) ◽  
pp. 41
Author(s):  
Ainhoa Riquelme ◽  
Pilar Rodrigo ◽  
María Dolores Escalera-Rodriguez ◽  
Joaquin Rams
Keyword(s):  
Wear Resistance ◽  
Aluminum Alloy ◽  
Wear Rate ◽  
Oxide Layer ◽  
Laser Cladding ◽  
Wear Behavior ◽  
Aluminum Matrix ◽  
Aluminum Matrix Composites ◽  
Matrix Composites ◽  
Sic Particles

Ceramic-reinforced metal matrix composites are known for their high wear resistance. A coating based on these materials would be helpful to improve the wear behavior of aluminum alloys. Laser cladding has been used to deposit a coating consisting of an aluminum alloy reinforced with SiC particles on an AA6082 aluminum alloy. Laser cladding is a very energetic technique that causes the SiC particles to react with the molten aluminum to form Al4C3, which degrades the particles and reduces the properties of the coating. The formation of this detrimental compound was successfully achieved with the addition of Silicon and Titanium to the composite matrix. The microstructures of the newly developed material were characterized and the wear behavior was studied under dry sliding conditions on a pin-on-disc tribometer. The relationship between the microstructure and wear behavior was identified. The absence of Al4C3 in the Al40Si/SiC and Al12Si20Ti/SiC coatings’ microstructures resulted in an abrasion mechanism instead of a delamination mechanism. The wear behavior changed along the sliding distances. During the first 200 m of sliding distances, the wear rate of all coatings was lower than the uncoated one due to their higher microhardness. For longer sliding distances, the wear resistance of the uncoated AA6082 was higher than the coated ones due to the formation of a lubricant oxide layer on the AA6082 worn surface. For 1000 m of wear distances, the wear behavior was different for each coating. The wear rate of the Al12Si/SiC coating continued growing due to the delamination mechanism and the presence of Al4C3 that acted as starting crack points. The wear rate of the Al40Si/SiC coating decreased due to the formation of a thin, superficial oxide layer. The wear rate of the Al12SiTi/SiC progressively decreased along the sliding distance to below the substrate wear rate.

Volume Fraction Dependent Wear Behavior of Titanium-Reinforced Aluminum Matrix Composites Manufactured by Melt Infiltration Casting

2018 ◽  
Vol 141 (2) ◽  
Author(s):  
Ridvan Gecu ◽  
Ahmet Karaaslan
Keyword(s):  
Wear Resistance ◽  
Volume Fraction ◽  
Wear Behavior ◽  
Pure Titanium ◽  
Aluminum Matrix ◽  
Aluminum Matrix Composites ◽  
Matrix Composites ◽  
Melt Infiltration ◽  
Cp Ti ◽  
Melt Infiltration Casting

This study aims to investigate the effect of volume fraction of commercially pure titanium (CP-Ti) on microstructural, mechanical, and tribological features of A356 aluminum matrix composites. Vacuum-assisted melt infiltration casting was performed to produce composites with 50%, 65%, 75%, and 80% CP-Ti contents. CP-Ti sawdusts were assembled under mechanical pressure in order to attain porous one-piece CP-Ti preforms which were infiltrated by A356 melt at 730 °C under 10−5 Pa vacuum atmosphere. TiAl3 layer was formed at the interface between A356 and CP-Ti phases. Owing to increased diffusion time through decreased diffusion path length, both thickness and hardness of TiAl3 phase were increased with increasing CP-Ti ratio, whereas the best wear resistance was obtained at 65% CP-Ti ratio. The main reason for decrease in wear resistance of 75% and 80% CP-Ti reinforced composites was fragmentation of TiAl3 layer during wear process due to its excessively increased brittleness. Strongly bonded TiAl3 phase at the interface provided better wear resistance, while weakly bonded ones caused to multiply wear rate.

scholarly journals Evaluation of the Wear Resistance and Corrosion Behavior of Laser Cladding Al/SiC Metal Matrix Composite Coatings on ZE41 Magnesium Alloy

Coatings ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 639
Author(s):  
Ainhoa Riquelme ◽  
Pilar Rodrigo ◽  
María Dolores Escalera-Rodriguez ◽  
Joaquín Rams
Keyword(s):  
Wear Resistance ◽  
Magnesium Alloy ◽  
Corrosion Behavior ◽  
Laser Cladding ◽  
Wear Behavior ◽  
Composite Coatings ◽  
Aluminum Matrix ◽  
Aluminum Matrix Composites ◽  
Wear Rates ◽  
Pin On Disc

Aluminum matrix composites reinforced with SiC particles (SiCp) were deposited on ZE41 magnesium substrates by laser cladding in order to improve their tribological performance. Silicon and titanium were added to the matrix in order to avoid Al-SiC reactivity. The addition of these elements to avoid Al4C3 formation during the laser cladding fabrication was successfully explored in previous research, but the effect of these elements on the wear behavior and the corrosion resistance of these coatings has not been studied. During the fabrication process, there is dilution with the substrate that forms an Al-Mg matrix, which has an influence on the wear and corrosion behavior. Electrochemical polarization and impedance measurements in a 3.5% NaCl solution and the dry sliding conditions on a pin-on-disc tribometer were used to evaluate the different compositions of Al/SiCp coatings on the ZE41 magnesium alloy and uncoated ZE41. All of the composite coatings had lower wear rates than the substrate. However, the coatings showed worse corrosion behavior than the ZE41 substrate, although the addition of Si or Ti improves the corrosion behavior and the wear resistance.

Squeeze casting of SiCp/Al-alloy composites with various contents of reinforcements

2002 ◽  
Vol 17 (2) ◽  
pp. 376-385 ◽  
Author(s):  
Liang-Guang Chen ◽  
Kung-Hsien Shue ◽  
Shou-Yi Chang ◽  
Su-Jien Lin
Keyword(s):  
Aluminum Alloy ◽  
Melting Point ◽  
Squeeze Casting ◽  
Pure Aluminum ◽  
Aluminum Matrix ◽  
Aluminum Matrix Composites ◽  
Al Alloy ◽  
Matrix Composites ◽  
Sic Particles ◽  
Silicon Carbide Particles

Aluminum matrix composites reinforced with various contents and sizes of silicon carbide particles (SiCp) were fabricated by squeeze casting. A lower melting point AA A383 aluminum alloy (A383 Al) was squeezed into the higher melting point SiCp/pure aluminum (SiCp/pure Al) and SiCp/AA 6061 aluminum alloy (SiCp/6061 Al) preforms. The volume percents of the ceramic reinforcements were effectively lowered from traditional 50 to 8–25 vol% by the addition of pure Al and 6061 Al powders in the preforms. The SiC particles uniformly distributed within the matrices, and no pore was found in these composites. The growth of silicon precipitates in A383 Al alloys was limited by the addition of the aluminum alloy powders and SiC particles, and the tensile properties of the alloys were effectively enhanced by the refinement of the silicon precipitates. The tensile strengths and elongations of the SiCp/pure Al/A383 Al and SiCp/6061 Al/A383 Al composites were both better than those of the A383 Al alloy. The T6-treated 12-μm SiCp/6061 Al/A383 Al composite exhibited the highest tensile strength of 301 MPa.

Dry Sliding Wear Behavior of Silicon Carbide Particulate Reinforced AA6061 Aluminum Alloy Composites Produced via Stir Casting

2014 ◽  
Vol 984-985 ◽  
pp. 221-226
Author(s):  
J. Jebeen Moses ◽  
S. Joseph Sekhar
Keyword(s):  
Aluminum Alloy ◽  
Sliding Wear ◽  
Wear Behavior ◽  
Aluminum Matrix ◽  
Stir Casting ◽  
Dry Sliding Wear ◽  
Aluminum Matrix Composites ◽  
Dry Sliding ◽  
Sic Particles ◽  
Silicon Carbide Particulate

Stir casting is an economical method to produce aluminum matrix composites (AMCs). In the present work, Aluminum alloy AA6061 reinforced with various amounts (0, 5, 10 and 15wt. %) of SiC particles were prepared. The matrix alloy was melted in a furnace and stirred to form a vortex. SiC particles were added to the periphery of the vortex and the composite melt was solidified in a permanent mold. The microstructures of the AMCs were studied using optical and scanning electron microscopy. SiC particles were observed to refine the grains and were distributed homogeneously in the aluminum matrix. SiC particle clusters were also seen in a few places. SiC particles were properly bonded to the aluminum matrix. Dry sliding wear behavior was analyzed by Pin on Disc apparatus. The reinforcement of SiC particles improved the wear resistance of the AMCs.The details of worn surface and wear debris are also presented in this paper.

Investigation of the Wear Behavior of AA6082 Against Different Counterparts

2021 ◽  
Author(s):  
Safiye İpek Ayvaz ◽  
Mehmet Ayvaz
Keyword(s):  
Wear Resistance ◽  
Aluminum Alloy ◽  
Wear Rate ◽  
Abrasive Wear ◽  
Wear Behavior ◽  
Specific Wear Rate ◽  
Pin On Disk ◽  
Disk Method ◽  
Sliding Distance ◽  
Oxidation Wear

In this study, the effect of different counterparts on the wear resistance of AA6082 aluminum alloy was investigated. In tests using pin-on-disk method, 6 mm diameter Al2O3, 100Cr6 and WC-6Co balls were used as counterparts. The tests were carried out using 500 m sliding distance and 5N load. The lowest specific wear rate was measured as 7.58x10-4 mm3/Nm in WC-6Co / AA6082 couple, and the highest value was measured as 9.71x10-4 mm3/Nm in 100Cr6/AA6082 couple. In the Al2O3/AA6082 couple, the specific wear rate of the AA6082-T6 sample was determined as 8.23x10-4 mm3/Nm.While it was observed that the dominant wear type in the 100Cr6/AA6082 pair was abrasive wear, oxidation wear and oxide tribofilm were detected in the WC-6Co/AA6082 and Al2O3/AA6082 couple besides the abrasive wear.

Research on Fabrication and Semisolid Processing of Semisolid Slurries of 7075 Aluminum Matrix Composites Reinforced with Nano-Sized SiC Particles

2016 ◽  
Vol 256 ◽  
pp. 81-87 ◽  
Author(s):  
Ju Fu Jiang ◽  
Ying Wang ◽  
Shou Jing Luo
Keyword(s):  
Acoustic Streaming ◽  
Aluminum Matrix ◽  
Aluminum Matrix Composite ◽  
Aluminum Matrix Composites ◽  
Semisolid Slurry ◽  
Matrix Composites ◽  
Good Surface ◽  
Sic Particles ◽  
The Matrix ◽  
Cylindrical Parts

Semisolid slurries of 7075 aluminum matrix composite reinforced with nano-sized SiC particles were fabricated by ultrasonic assisted semisolid stirring (UASS) method. Rheoforming and thixoforming of typical cylindrical parts were investigated. The results show that high-quality semisolid slurries with spheroidal solid grain of 38 µm were fabricated by UASS. The nano-sized SiC particles were dispersed uniformly due to transient cavitation and acoustic streaming of ultrasonic wave and high and controllable viscosity of semisolid slurry. Typical cylindrical composite parts with good surface quality and complete filling were rheoformed and thixoformed successfully. Ultimate tensile strength (UTS) of the rheoformed and thixoformed composite parts are enhanced due to addition of nano-sized SiC particles. However, elongation decreased as compared to those of the matrix parts. Maximum UTS of 550 MPa was achieved in the thixoformed composite part with T6 treatment. Increase of dislocation density around the reinforcement particles leads to improvement of the strength and wear resistance of the composite.

Microstructure and Properties of SiC Particle Reinforced Aluminum Matrix Composites by Powder Metallurgy Method

2013 ◽  
Vol 457-458 ◽  
pp. 131-134 ◽  
Author(s):  
Tao Fan ◽  
Cong Li Xiao ◽  
Yan Rong Sun ◽  
Hong Bo Li
Keyword(s):  
Particle Size ◽  
Wear Resistance ◽  
Powder Metallurgy ◽  
Sintering Temperature ◽  
Aluminum Matrix ◽  
Aluminum Matrix Composites ◽  
Average Particle ◽  
Particle Sizes ◽  
Matrix Composites ◽  
Sic Particle

The aim of this study is to investigate the effect of SiC particle pretreatment, aluminum matrix particle size and sintering temperature on relative density, hardness, microstructure and wear resistance to SiC particle einforced aluminum matrix composites. To this end, the amount of 16.7 wt.% SiC with average particle sizes 20μm was used along with pure aluminum of average particle size of 75 μm and 25μm. Powder metallurgy is a method used in the fabrication of this composite in which the powders were mixed using a planetary ball mill. By analyzing SEM micrograph and the Property test, it is concluded that SiC particle pretreatment has significant effect on the morphology of pecimens. pretreatment increase the interface adhesion, improve the wettability. SiC is uniformly distributed in the matrix, with good relation to the substrate, the maximum hardness is 51.1HB, the minimum wear rate is 0.1684%, while the density is 97.3%.For the same SiC content and particle size, the smaller the particle size of aluminum matrix is, the higher wear resistance of composite materials is on condition that others are same, the higher sintering temperature and the higher the wearability of composites, the wear resistance of the composite material is significantly improved after SiC pre-processing.The relative density increases with increasing aluminum matrix particle sizes under the same pressure and the holding time. The actual density of all samples reached the theoretical density over 96%, to a maximum of 98.9%.

scholarly journals Enhancement of the Wear Resistance and Microhardness of Aluminum Alloy by Nd:YaG Laser Treatment

2014 ◽  
Vol 2014 ◽  
pp. 1-5 ◽  
Author(s):  
Haitham T. Hussein ◽  
Abdulhadi Kadhim ◽  
Ahmed A. Al-Amiery ◽  
Abdul Amir H. Kadhum ◽  
Abu Bakar Mohamad
Keyword(s):  
Wear Resistance ◽  
Aluminum Alloy ◽  
Wear Rate ◽  
Laser Treatment ◽  
Vickers Hardness ◽  
Nd:Yag Laser ◽  
Wear Behavior ◽  
X Ray ◽  
Before And After ◽  
Hardness Values

Influence of laser treatment on mechanical properties, wear resistance, and Vickers hardness of aluminum alloy was studied. The specimens were treated by using Nd:YaG laser of energy 780 mj, wavelength 512 nm, and duration time 8 ns. The wear behavior of the specimens was studied for all specimens before and after treatment by Nd:YaG laser and the dry wear experiments were carried out by sing pinon-disc technique. The specimens were machined as a disk with diameter of 25 mm and circular groove in depth of 3 mm. All specimens were conducted by scanning electron microscopy (SEM), energy-dispersive X-ray florescence analysis (EDS), optical microscopy, and Vickers hardness. The results showed that the dry wear rate was decreased after laser hardening and increased Vickers hardness values by ratio of 2.4 : 1. The results showed that the values of wear rate for samples having circular grooves are less than samples without grooves after laser treatment.

Sign in / Sign up

Export Citation Format

Share Document