scholarly journals Development of Novel Lightweight Dual-Phase Al-Ti-Cr-Mn-V Medium-Entropy Alloys with High Strength and Ductility

Entropy ◽  
2020 ◽  
Vol 22 (1) ◽  
pp. 74
Author(s):  
Yu-Chin Liao ◽  
Po-Sung Chen ◽  
Chao-Hsiu Li ◽  
Pei-Hua Tsai ◽  
Jason Jang ◽  
...  
Keyword(s):  
Compression Strength ◽  
High Strength ◽  
Alloy System ◽  
Dual Phase ◽  
Face Centered Cubic ◽  
Compression Tests ◽  
Arc Melting ◽  
Face Centered ◽  
Fcc Phase ◽  
Strength And Ductility

A novel lightweight Al-Ti-Cr-Mn-V medium-entropy alloy (MEA) system was developed using a nonequiatiomic approach and alloys were produced through arc melting and drop casting. These alloys comprised a body-centered cubic (BCC) and face-centered cubic (FCC) dual phase with a density of approximately 4.5 g/cm3. However, the fraction of the BCC phase and morphology of the FCC phase can be controlled by incorporating other elements. The results of compression tests indicated that these Al-Ti-Cr-Mn-V alloys exhibited a prominent compression strength (~1940 MPa) and ductility (~30%). Moreover, homogenized samples maintained a high compression strength of 1900 MPa and similar ductility (30%). Due to the high specific compressive strength (0.433 GPa·g/cm3) and excellent combination of strength and ductility, the cast lightweight Al-Ti-Cr-Mn-V MEAs are a promising alloy system for application in transportation and energy industries.

The Influence of Stacking Fault Energy on the Cold-Rolling Cu and Cu-Al Alloy: Structure and Mechanics Properties

2011 ◽  
Vol 683 ◽  
pp. 95-102 ◽  
Author(s):  
Hao Yang ◽  
Peng Yang ◽  
Jing Mei Tao ◽  
Cai Ju Li ◽  
Xin Kun Zhu
Keyword(s):  
Cold Rolling ◽  
Deformation Twin ◽  
High Strength ◽  
Liquid Nitrogen Temperature ◽  
Al Alloy ◽  
Face Centered Cubic ◽  
X Ray Diffraction ◽  
X Ray ◽  
Face Centered ◽  
Strength And Ductility

Sacking fault energy (SFE) is the key role in solving this problem of getting high strength and expected ductility simultaneously. This work adds Al as the procedure of decreasing SFE in Cu face-centered cubic. It is an economic and effective method to counterpart Cold-rolling at liquid nitrogen temperature to get high density deformation twin and ultrafine-grains size. After undergoing tensile and X-ray diffraction tests, Cu-4.5 wt.% Al plays the best performance on both strength and ductility. Thus there exist the optimal SFE of Cu-Al alloys which get both high strength and expected ductility simultaneously.

L21-strengthened face-centered cubic high-entropy alloy with high strength and ductility

2020 ◽  
Vol 797 ◽  
pp. 140056 ◽  
Author(s):  
Yongliang Qi ◽  
Yake Wu ◽  
Tinghui Cao ◽  
Lin He ◽  
Feng Jiang ◽  
...  
Keyword(s):  
High Strength ◽  
High Entropy Alloy ◽  
Face Centered Cubic ◽  
High Entropy ◽  
Face Centered ◽  
Strength And Ductility

scholarly journals Tailoring Compressive Strength and Absorption Energy of Lightweight Multi-Phase AlCuSiFeX (X = Cr, Mn, Zn, Sn) High-Entropy Alloys Processed via Powder Metallurgy

Materials ◽  
2021 ◽  
Vol 14 (17) ◽  
pp. 4945
Author(s):  
Ashutosh Sharma ◽  
Hansung Lee ◽  
Byungmin Ahn
Keyword(s):  
Powder Metallurgy ◽  
Low Cost ◽  
High Strength ◽  
Fracture Mechanisms ◽  
Solid Solution Phase ◽  
Face Centered Cubic ◽  
Σ Phase ◽  
High Entropy ◽  
Face Centered ◽  
Fcc Phase

The development of lightweight HEAs with high strength and low cost is an urgent requirement. In this study, equimolar AlCuSiFeX (X = Cr, Mn, Zn, Sn) lightweight HEAs were fabricated by advanced powder metallurgy. The mechanical alloying was performed for 45 h, and the powder compacts were densified at 650 °C. The final results revealed that AlCuSiFeSn lightweight HEA was composed of a single face-centered cubic (FCC) and Cu81Sn22, whereas AlCuSiFeZn showed a dual FCC and body-centered cubic (BCC) structures. Similarly, AlCuSiFeMn alloy contained a BCC + FCC phase with a µ-phase, whereas a σ-phase was present in AlCuSiFeCr in addition to FCC + BCC phases. We also calculated various thermodynamic parameters to predict the solid-solution phase stability of each of the above lightweight HEAs. It was found that lightweight HEAs with additive elements Sn and Zn tend to predominant FCC phases, whereas those with Cr and Mn result in major BCC with hard µ and σ phases, which further improve their mechanical strength. A maximum fracture strain of 23% was obtained for AlCuSiFeSn followed by 19% for AlCuSiFeZn HEA. The compressive fracture mechanisms of these lightweight HEAs are also discussed and reported here.

scholarly journals Novel Co-Cu-Based Immiscible Medium-Entropy Alloys with Promising Mechanical Properties

Metals ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 238
Author(s):  
Sujung Son ◽  
Jongun Moon ◽  
Hyeonseok Kwon ◽  
Peyman Asghari Rad ◽  
Hidemi Kato ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Binary System ◽  
Design Methodology ◽  
Miscibility Gap ◽  
Face Centered Cubic ◽  
Solid Solution Strengthening ◽  
Solution Strengthening ◽  
Face Centered ◽  
Strength And Ductility ◽  
Cobalt Copper

New AlxCo50−xCu50−xMnx (x = 2.5, 10, and 15 atomic %, at%) immiscible medium-entropy alloys (IMMEAs) were designed based on the cobalt-copper binary system. Aluminum, a strong B2 phase former, was added to enhance yield strength and ultimate tensile strength, while manganese was added for additional solid solution strengthening. In this work, the microstructural evolution and mechanical properties of the designed Al-Co-Cu-Mn system are examined. The alloys exhibit phase separation into dual face-centered cubic (FCC) phases due to the miscibility gap of the cobalt-copper binary system with the formation of CoAl-rich B2 phases. The hard B2 phases significantly contribute to the strength of the alloys, whereas the dual FCC phases contribute to elongation mitigating brittle fracture. Consequently, analysis of the Al-Co-Cu-Mn B2-strengthened IMMEAs suggest that the new alloy design methodology results in a good combination of strength and ductility.

scholarly journals Irradiation Behaviors in BCC Multi-Component Alloys with Different Lattice Distortions

Metals ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 706
Author(s):  
Yue Su ◽  
Songqin Xia ◽  
Jia Huang ◽  
Qingyuan Liu ◽  
Haocheng Liu ◽  
...  
Keyword(s):  
Single Phase ◽  
Vacuum Arc ◽  
Face Centered Cubic ◽  
Body Centered Cubic ◽  
Chemical Complexity ◽  
Arc Melting ◽  
Vacuum Arc Melting ◽  
Lattice Distortions ◽  
Face Centered ◽  
Displacement Per Atom

Recently, the irradiation behaviors of multi-component alloys have stimulated an increasing interest due to their ability to suppress the growth of irradiation defects, though the mostly studied alloys are limited to face centered cubic (fcc) structured multi-component alloys. In this work, two single-phase body centered cubic (bcc) structured multi-component alloys (CrFeV, AlCrFeV) with different lattice distortions were prepared by vacuum arc melting, and the reference of α-Fe was also prepared. After 6 MeV Au ions irradiation to over 100 dpa (displacement per atom) at 500 °C, the bcc structured CrFeV and AlCrFeV exhibited significantly improved irradiation swelling resistance compared to α-Fe, especially AlCrFeV. The AlCrFeV alloy possesses superior swelling resistance, showing no voids compared to α-Fe and CrFeV alloy, and scarce irradiation softening appears in AlCrFeV. Owing to their chemical complexity, it is believed that the multi-component alloys under irradiation have more defect recombination and less damage accumulation. Accordingly, we discuss the origin of irradiation resistance and the Al effect in the studied bcc structured multi-component alloys.

scholarly journals Stability and equation of state of face-centered cubic and hexagonal close packed phases of argon under pressure

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Agnès Dewaele ◽  
Angelika D. Rosa ◽  
Nicolas Guignot ◽  
Denis Andrault ◽  
João Elias F. S. Rodrigues ◽  
...  
Keyword(s):  
Equation Of State ◽  
Single Crystal ◽  
Single Crystal Sample ◽  
Moderate Pressure ◽  
Face Centered Cubic ◽  
Experimental Conditions ◽  
Crystal Sample ◽  
Hexagonal Close Packed ◽  
Face Centered ◽  
Fcc Phase

AbstractThe compression of argon is measured between 10 K and 296 K up to 20 GPa and and up to 114 GPa at 296 K in diamond anvil cells. Three samples conditioning are used: (1) single crystal sample directly compressed between the anvils, (2) powder sample directly compressed between the anvils, (3) single crystal sample compressed in a pressure medium. A partial transformation of the face-centered cubic (fcc) phase to a hexagonal close-packed (hcp) structure is observed above 4.2–13 GPa. Hcp phase forms through stacking faults in fcc-Ar and its amount depends on pressurizing conditions and starting fcc-Ar microstructure. The quasi-hydrostatic equation of state of the fcc phase is well described by a quasi-harmonic Mie–Grüneisen–Debye formalism, with the following 0 K parameters for Rydberg-Vinet equation: $$V_0$$ V 0 = 38.0 Å$$^3$$ 3 /at, $$K_0$$ K 0 = 2.65 GPa, $$K'_0$$ K 0 ′ = 7.423. Under the current experimental conditions, non-hydrostaticity affects measured P–V points mostly at moderate pressure ($$\le$$ ≤ 20 GPa).

scholarly journals Development of Novel Lightweight Al-Rich Quinary Medium-Entropy Alloys with High Strength and Ductility

Materials ◽  
2021 ◽  
Vol 14 (15) ◽  
pp. 4223
Author(s):  
Po-Sung Chen ◽  
Yu-Chin Liao ◽  
Yen-Ting Lin ◽  
Pei-Hua Tsai ◽  
Jason S. C. Jang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Compressive Strain ◽  
High Strength ◽  
Fine Tuning ◽  
Face Centered Cubic ◽  
Transportation Industry ◽  
High Entropy ◽  
Good Potential ◽  
Face Centered

Most high-entropy alloys and medium-entropy alloys (MEAs) possess outstanding mechanical properties. In this study, a series of lightweight nonequiatomic Al50–Ti–Cr–Mn–V MEAs with a dual phase were produced through arc melting and drop casting. These cast alloys were composed of body-centered cubic and face-centered cubic phases. The density of all investigated MEAs was less than 5 g/cm3 in order to meet energy and transportation industry requirements. The effect of each element on the microstructure evolution and mechanical properties of these MEAs was investigated. All the MEAs demonstrated outstanding compressive strength, with no fractures observed after a compressive strain of 20%. Following the fine-tuning of the alloy composition, the Al50Ti20Cr10Mn15V5 MEA exhibited the most compressive strength (~1800 MPa) and ductility (~34%). A significant improvement in the mechanical compressive properties was achieved (strength of ~2000 MPa, strain of ~40%) after annealing (at 1000 °C for 0.5 h) and oil-quenching. With its extremely high specific compressive strength (452 MPa·g/cm3) and ductility, the lightweight Al50Ti20Cr10Mn15V5 MEA demonstrates good potential for energy or transportation applications in the future.

scholarly journals Effect of Mn Addition on the Microstructures and Mechanical Properties of CoCrFeNiPd High Entropy Alloy

Entropy ◽  
2019 ◽  
Vol 21 (3) ◽  
pp. 288
Author(s):  
Yiming Tan ◽  
Jinshan Li ◽  
Jun Wang ◽  
Hongchao Kou
Keyword(s):  
Intermetallic Compound ◽  
Interface Energy ◽  
High Entropy Alloy ◽  
Strengthening Effect ◽  
Face Centered Cubic ◽  
Liquid Interfaces ◽  
High Entropy ◽  
Single Face ◽  
Face Centered ◽  
Fcc Phase

CoCrFeNiPdMnx (x = 0, 0.2, 0.4, 0.6, 0.8) high entropy alloys (HEAs) were prepared and characterized. With an increase in Mn addition, the microstructures changed from dendrites (CoCrFeNiPd with a single face-centered-cubic (FCC) phase) to divorced eutectics (CoCrFeNiPdMn0.2 and CoCrFeNiPdMn0.4), to hypoeutectic microstructures (CoCrFeNiPdMn0.6), and finally to seaweed eutectic dendrites (CoCrFeNiPdMn0.8). The addition of Mn might change the interface energy anisotropy of both the FCC/liquid and MnPd-rich intermetallic compound/liquid interfaces, thus forming the seaweed eutectic dendrites. The hardness of the FCC phase was found to be highly related to the solute strengthening effect, the formation of nanotwins and the transition from CoCrFeNiPd-rich to CoCrFeNi-rich FCC phase. Hierarchical nanotwins were found in the MnPd-rich intermetallic compound and a decrease in either the spacing of primary twins or secondary twins led to an increase in hardness. The designing rules of EHEAs were discussed and the pseudo binary method was revised accordingly.

scholarly journals Dual phase nano-particulate AlN composite — A kind of ceramics with high strength and ductility

2019 ◽  
Vol 45 (16) ◽  
pp. 19845-19855
Author(s):  
Yinbo Zhao ◽  
Xianghe Peng ◽  
Bo Yang ◽  
Cheng Huang ◽  
Ning Hu ◽  
...  
Keyword(s):  
High Strength ◽  
Dual Phase ◽  
Strength And Ductility
Sign in / Sign up

Export Citation Format

Share Document