scholarly journals Experimental Study on the Thermal and Electrical Characteristics of an Air-Based Photovoltaic Thermal Collector

Energies ◽  
2019 ◽  
Vol 12 (14) ◽  
pp. 2661 ◽  
Author(s):  
Sang-Myung Kim ◽  
Jin-Hee Kim ◽  
Jun-Tae Kim
Keyword(s):  
Flow Rate ◽  
Thermal Performance ◽  
Thermal Efficiency ◽  
Solar Thermal ◽  
Electrical Performance ◽  
Energy Output ◽  
Inlet Flow ◽  
Pv Module ◽  
Solar Thermal Collector ◽  
Inlet Flow Rate

A photovoltaic thermal (PVT) system is a technology that combines photovoltaics (PV) and a solar thermal collector to produce thermal energy and generate electricity. PVT systems have the advantage that the energy output per unit area is higher than the single use of a PV module or solar thermal collector, since both heat and electricity can be produced and used simultaneously. Air-based PVT collectors use air as the heat transfer medium and flow patterns are important factors that affect the performance of the PVT collector. In this study, the thermal and electrical performance and characteristics of an air-based PVT collector were analyzed through experiments. The PVT collector, with bending round-shaped heat-absorbing plates, which increase the air flow path, has been developed to improve the thermal performance. The experiment was done under the test conditions of ISO 9806:2017 for the thermal performance analysis of an air-based PVT collector. The electrical performance was analyzed under the same conditions. In the results, it can be found that the inlet flow rate of the PVT collector considerably affects the thermal efficiency. It was analyzed that as the inlet flow rate increased from 60 to 200 m3/h, the thermal efficiency increased from 29% to 42%. Then, the electricity efficiency was also analyzed, where it was determined that it was improved according to operating condition of PVT collector.

scholarly journals Potential of Solar Collectors for Clean Thermal Energy Production in Smart Cities using Nanofluids: Experimental Assessment and Efficiency Improvement

2019 ◽  
Vol 9 (9) ◽  
pp. 1877 ◽  
Author(s):  
M. Sarafraz ◽  
Iskander Tlili ◽  
Mohammad Abdul Baseer ◽  
Mohammad Safaei
Keyword(s):  
Flow Rate ◽  
Thermal Performance ◽  
Tilt Angle ◽  
Thermal Efficiency ◽  
Smart Cities ◽  
Heat Pipes ◽  
Filling Ratio ◽  
Working Fluid ◽  
Solar Thermal Collector ◽  
Evacuated Tube

In this article, an experimental study was performed to assess the potential thermal application of a new nanofluid comprising carbon nanoparticles dispersed in acetone inside an evacuated tube solar thermal collector. The effect of various parameters including the circulating volumetric flow of the collector, mass fraction of the nanoparticles, the solar irradiance, the tilt angle and the filling ratio values of the heat pipes on the thermal performance of the solar collector was investigated. It was found that with an increase in the flow rate of the working fluid within the system, the thermal efficiency of the system was improved. Additionally, the highest thermal performance and the highest temperature difference between the inlet and the outlet ports of the collector were achieved for the nanofluid at wt. % = 0.1. The best tilt angle and the filling ratio values of the collector were 30° and 60% and the maximum thermal efficiency of the collector was 91% for a nanofluid at wt. % = 0.1 and flow rate of 3 L/min.

ANALYSIS OF THE THERMAL EFFICIENCY OF A SOLAR THERMAL COLLECTOR FOR LOW-INCOME FAMILIES

2018 ◽  
Author(s):  
Julia Maria Massareli Costa ◽  
Guilherme Viana ◽  
Vinicius Cruz ◽  
Felipe Boragina da silva ◽  
Ana Beatriz Valentin ◽  
...  
Keyword(s):  
Low Income ◽  
Thermal Efficiency ◽  
Solar Thermal ◽  
Solar Thermal Collector ◽  
Low Income Families

scholarly journals Investigation of the transport characteristics of Pb(II) in sand-bone char columns

2021 ◽  
Vol 104 (2) ◽  
pp. 003685042110236
Author(s):  
Gang Li ◽  
Jinli Zhang ◽  
Jia Liu ◽  
Tao Luo ◽  
Yu Xi
Keyword(s):  
Adsorption Capacity ◽  
Flow Rate ◽  
Dose Response ◽  
Construction Materials ◽  
Column Height ◽  
Maximum Adsorption Capacity ◽  
Complexation Reaction ◽  
Bone Char ◽  
Inlet Flow ◽  
Inlet Flow Rate

Pb(II) leakage from batteries, dyes, construction materials, and gasoline threaten human health and environmental safety, and suitable adsorption materials are vitally important for Pb(II) removal. Bone char is an outstanding adsorbent material for water treatment, and the effectiveness in Pb(II) removing need to be verified. In this paper, the transport characteristics of Pb(II) in columns filled with a sand and bone char mixture were studied at the laboratory scale, and the influences of the initial concentration, column height, inlet flow rate, and competing ion Cu(II) on Pb(II) adsorption and transport were analyzed. The Thomas and Dose-Response models were used to predict the test results, and the mechanisms of Pb(II) adsorption on bone char were investigated. The results showed that the adsorption capacity of the bone char increased with increasing column height and decreased with increasing initial Pb(II) concentration, flow rate, and Cu(II) concentration. The maximum adsorption capacity reached 38.466 mg/g and the saturation rate was 95.8% at an initial Pb(II) concentration of 200 mg/L, inlet flow rate of 4 mL/min, and column height of 30 cm. In the competitive binary system, the higher the Cu(II) concentration was, the greater the decreases in the breakthrough and termination times, and the faster the decrease in the Pb(II) adsorption capacity of the bone char. The predicted results of the Dose-Response model agreed well with the experimental results and were significantly better than those of the Thomas model. The main mechanisms of Pb(II) adsorption on bone char include a surface complexation reaction and the decomposition-replacement-precipitation of calcium hydroxyapatite (CaHA). Based on selectivity, sensitivity, and cost analyses, it can be concluded that bone char is a potential adsorbent for Pb(II)-containing wastewater treatment.

Research on the Removal Results of Hydrogen Sulfide of the Treatment of Coal Gasification Wastewater Biogas in the Anaerobic Biotrickling Filter

2012 ◽  
Vol 610-613 ◽  
pp. 2000-2005
Author(s):  
Chun Yan Xu ◽  
Hong Jun Han
Keyword(s):  
Hydrogen Sulfide ◽  
Removal Efficiency ◽  
Flow Rate ◽  
Retention Time ◽  
Operating Parameters ◽  
Inlet Flow ◽  
H2s Removal ◽  
Outlet Concentration ◽  
Volume Load ◽  
Inlet Flow Rate

The uncertainty of operating parameters hinders the practical application of the biological desulfurization. To solve this problem, this study which was conducted in room temperature, pH around seven conditions, investigated the effects of the operating parameters on the hydrogen sulfide (H2S) removal performance in the biotrickling filter, including inlet H2S concentration, inlet flow rate or gas retention time, inlet volume load and circulating liquid spraying flux. The results showed that, the inlet H2S concentration should be controlled within 800mg/m3, 650mg/m3, 400mg/m3, 300mg/m3 respectively while the inlet flow rate was 150L/h, 200L/h, 250L/h, 300L/h, at those conditions, the outlet H2S concentrations were lower than 8mg/m3 and the H2S removal efficiencies were more than 98%. The optimum gas retention time was 12.37s, corresponding to the inlet flow rate of 200L/h, at this time, even if the inlet H2S concentration as high as 700mg/m3, the removal efficiency could be still more than 98%, the outlet concentration of H2S was only 13.1mg/m3. The maximum inlet volume load was 130g/(m3•h), in this condition, the outlet concentration of H2S could be controlled below 12mg/m3, the removal efficiency could above 98.4%.

A new method for prediction of the acoustic performance and design parameter sensitivity analysis of multi-chamber perforated resonators with an irregular cross-section

2021 ◽  
pp. 1-24
Author(s):  
Rong Guo ◽  
Zanzan Sun ◽  
Zhen Huang ◽  
Rui Luo
Keyword(s):  
Theoretical Prediction ◽  
Cross Section ◽  
Flow Rate ◽  
New Method ◽  
Frequency Noise ◽  
Acoustic Characteristics ◽  
Inlet Flow ◽  
Acoustic Performance ◽  
Inlet Flow Rate ◽  
Prediction Approach

Abstract Aiming at reducing the high-amplitude and wide-frequency noise in charged air intake system of the powertrain, this paper proposes a new method for predicting the acoustic characteristics of an irregular cross-section multi-chamber perforated resonator under flow conditions. By this method, the presence of three-dimensional sound waves and the effects of higher-order modes are considered, and the acoustic performance of the resonator can be evaluated through the computation of transmission loss. Moreover, by discretizing the cross-section of perforated resonator and extracting node information, this method can solve the acoustic characteristics of the perforated resonator with any cross-section. Based on the transfer matrix method, the quadrupole parameters of each chamber are obtained. Then the acoustic characteristics of the multi-chamber perforated resonator could be calculated. The theoretical prediction data and the experimental data have been compared and the results show good agreement within the entire frequency range, which verifies the accuracy of the theoretical prediction approach. Based on this prediction approach, the influence of section ratio, structure parameters and inlet flow rate on the acoustic characteristics of the resonator is explored. The results show that when the structural parameters change, the peak resonance frequency of the resonator will have a regular shift. With the increase of the inlet flow rate, the main frequency band of sound attenuation will decrease significantly. The theoretical method developed in this work can be used for the calculation and optimization of multi-chamber resonators in various applications.

Flow Analysis of a Hydrocyclone Designed to High Oil Content Application

2009 ◽  
Author(s):  
G. M. Raposo ◽  
A. O. Nieckele
Keyword(s):  
Experimental Data ◽  
Flow Rate ◽  
Oil Content ◽  
Flow Analysis ◽  
Turbulence Models ◽  
Reynolds Stress Model ◽  
Tangential Component ◽  
Inlet Flow ◽  
Unit Process ◽  
Inlet Flow Rate

Development of small size and weight separation equipment are crucial for the petroleum off-shore exploration. Since centrifugal fields are several times stronger than the gravity field, cyclonic separation has became very important as a unit process for compact gas-liquid, liquid-liquid and solid-liquid separation. The major difference between the various cyclones is their geometry. Cyclone optimization for different uses is, every year, less based on experiments and more based on mathematical models. In the present work, the flow field inside high oil content hydrocyclones is numerically obtained with FLUENT. The performance of two turbulence models, Reynolds Stress Model (RSM) and Large Eddy Simulation (LES), to predict the flow inside a high oil content hydrocyclone, is investigated by comparing the results with experimental data available in the literature. All models overpredicted the tangential component, especially at the reverse cone region. However, the prediction of the tangential turbulent fluctuations with LES was significant better than the RSM prediction. The influences of the inlet flow rate and hydrocyclone length in the flow were also evaluated. RSM model was able to foresee correctly, in agreement with experimental data, the correct tendency of pressure drop reduction with decreasing inlet flow rate and increasing length.

scholarly journals An experimental study of the thermal performance of the square and rhombic solar collectors

2018 ◽  
Vol 22 (1 Part B) ◽  
pp. 487-494 ◽  
Author(s):  
Aminreza Noghrehabadi ◽  
Ebrahim Hajidavaloo ◽  
Mojtaba Moravej ◽  
Ali Esmailinasab
Keyword(s):  
Experimental Study ◽  
Flat Plate ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Thermal Performance ◽  
Thermal Efficiency ◽  
Solar Collectors ◽  
Heating Systems ◽  
Solar Water Heating

Solar collectors are the key part of solar water heating systems. The most widely produced solar collectors are flat plate solar collectors. In the present study, two types of flat plate collectors, namely square and rhombic collectors are experi?mentally tested and compared and the thermal performance of both collectors is investigated. The results show both collectors have the same performance around noon (?61%), but the rhombic collector has better performance in the morning and afternoon. The values for rhombic and square collectors are approximately 56.2% and 53.5% in the morning and 56.1% and 54% in the afternoon, respectively. The effect of flow rate is also studied. The thermal efficiency of rhombic and square flat plate collectors increases in proportion to the flow rate. The results indicated the rhombic collector had better performance in comparison with the square collector with respect to the mass-flow rate.

scholarly journals Evaluating the Performance of Two Solar Domestic Hot Water Systems of the Archetype Sustainable Houses

2021 ◽  
Author(s):  
Kamyar Tanha
Keyword(s):  
Flat Plate ◽  
Hot Water ◽  
Experimental Results ◽  
Solar Thermal ◽  
Energy Output ◽  
Evacuated Tube Collector ◽  
Solar Thermal Collector ◽  
Solar Thermal Collectors ◽  
Evacuated Tube Collectors ◽  
Evacuated Tube

This thesis is focused on the performance of the two SDHW systems of the sustainable Archetype houses in Vaughan, Ontario with daily hot water consumption of 225 litres. The first system consists of a flat plate solar thermal collector in conjunction with a gas boiler and a DWHR. The second SDHW system consists of an evacuated tube collector, an electric tank and a DWHR. The experimental results showed that the DWHRs were capable of an annual heat recovery of 789 kWh. The flat plate and evacuated tube collectors had an annual thermal energy output of 2038 kWh and 1383 kWh. The systems were also modeled in TRNSYS and validated with the experimental results. The simulated results showed that Edmonton has the highest annual energy consumption of 3763.4 kWh and 2852.9 kWh by gas boiler and electric tank and that the solar thermal collectors and DWHRs are most beneficial in Edmonton.

scholarly journals Numerical Study of Bubble Rising and Coalescence Characteristics under Flow Pulsation Based on Particle Method

2019 ◽  
Vol 2019 ◽  
pp. 1-13
Author(s):  
Ronghua Chen ◽  
Minghao Zhang ◽  
Kailun Guo ◽  
Dawei Zhao ◽  
Wenxi Tian ◽  
...  
Keyword(s):  
Flow Rate ◽  
Two Phase Flow ◽  
Flow Instability ◽  
Numerical Study ◽  
Phase Flow ◽  
Flow Pulsation ◽  
Two Phase ◽  
Inlet Flow ◽  
Inlet Flow Rate ◽  
Bubble Rising

Two-phase flow instability may occur in nuclear reactor systems, which is often accompanied by periodic fluctuation in fluid flow rate. In this study, bubble rising and coalescence characteristics under inlet flow pulsation condition are analyzed based on the MPS-MAFL method. To begin with, the single bubble rising behavior under flow pulsation condition was simulated. The simulation results show that the bubble shape and rising velocity fluctuate periodically as same as the inlet flow rate. Additionally, the bubble pairs’ coalescence behavior under flow pulsation condition was simulated and compared with static condition results. It is found that the coalescence time of bubble pairs slightly increased under the pulsation condition, and then the bubbles will continue to pulsate with almost the same period as the inlet flow rate after coalescence. In view of these facts, this study could offer theory support and method basis to a better understanding of the two-phase flow configuration under flow pulsation condition.

scholarly journals Effect of Bed Particle Size on Thermal Performance of a Directly-Irradiated Fluidized Bed Gas Heater

Processes ◽  
2020 ◽  
Vol 8 (8) ◽  
pp. 967
Author(s):  
Sae Han Park ◽  
Chae Eun Yeo ◽  
Min Ji Lee ◽  
Sung Won Kim
Keyword(s):  
Particle Size ◽  
Fluidized Bed ◽  
Thermal Performance ◽  
Thermal Efficiency ◽  
Gas Velocity ◽  
Bubble Behavior ◽  
Heat Transfer Characteristics ◽  
Maximum Value ◽  
Solar Thermal Collector ◽  
Sic Particle

There is a growing interest in a fluidized bed particle receiver that directly irradiates sunlight to particles in the fluidized bed as a solar thermal collector for heating. Thermal performance of directly-irradiated fluidized bed gas heater is strongly affected by the physical properties of the particles. The effect of SiC particle size on heat transfer characteristics in the solar fluidized bed gas heater (50 mm-ID × 100 mm high) has been determined. The outlet gas temperatures showed a maximum value with increasing gas velocity due to the particles motion by bubble behavior in the bed, and the maximum values were found at 3.6 times of Umf for fine SiC and less than 2.0 times of Umf for coarse SiC. Heat absorption from the receiver increased with increasing gas velocity, showing with maximum 18 W for the fine SiC and 23 W for the coarse SiC at 4.5 times of Umf. The thermal efficiency of the receiver increased with increasing gas velocity, but was affected by the content of finer particles. The maximum thermal efficiency of the receiver was 14% for fine SiC and 20% for coarse SiC within the experimental range, but showing higher for the fine SiC at the same gas velocity. A design consideration was proposed to improve the thermal efficiency of the system.

Sign in / Sign up

Export Citation Format

Share Document