scholarly journals Effects of the Ratio of Porosity to Volumetric Cement Content on the Unconfined Compressive Strength of Cement Bound Fine Grained Soils

2021 ◽  
Vol 6 (7) ◽  
pp. 96
Author(s):  
Teresa Santana ◽  
João Gonçalves ◽  
Fernando Pinho ◽  
Rui Micaelo
Keyword(s):  
Compressive Strength ◽  
Unconfined Compressive Strength ◽  
Cement Content ◽  
Design Procedure ◽  
Dry Mass ◽  
Dry Density ◽  
Clayey Sand ◽  
Fine Grained ◽  
Type Iv ◽  
Different Soils

This paper presents an experimental investigation into the effects of porosity, dry density and cement content on the unconfined compressive strength and modulus of elasticity of cement-bound soil mixtures. A clayey sand was used with two different proportions of type IV Portland cement, 10% and 14% of the dry mass of the soil. Specimens were moulded with the same water content but using four different compaction efforts, corresponding to four different dry densities. Unconfined compression testing was conducted at seven days of curing time on unsoaked samples. The results showed that the compressive strength increased with the increase in cement content and with the decrease in porosity. From the experimental data, a unique relationship was found between the unconfined compressive strength and the ratio of porosity to volumetric cement content for all the mixtures and compaction efforts tested. The equation developed demonstrates that it is possible to estimate the amount of cement and the dry density to achieve a certain level of unconfined compressive strength. A normalized general equation was also found to fit other authors’ results for similar soils mixed with cement. From this, a cement-bound soil model was proposed for the development of a mixing design procedure for different soils.

scholarly journals ESTABILIZAÇÃO DE UM SOLO DA CAMADA CINZA DA FORMAÇÃO GUABIROTUBA PARA FINS DE PAVIMENTAÇÃO URBANA EM CURITIBA, BRASIL

2020 ◽  
Vol 12 (1) ◽  
pp. 39-52
Author(s):  
Jair de Jesús Arrieta Baldovino ◽  
Ronaldo Luis dos Santos Izzo
Keyword(s):  
Experimental Study ◽  
Compressive Strength ◽  
Unconfined Compressive Strength ◽  
Sedimentary Basin ◽  
Cement Content ◽  
Dry Mass ◽  
Curing Time ◽  
Cement Ratio ◽  
Semi Empirical ◽  
The City

The Guabirotuba Formation is located over the sedimentary basin of the city of Curitiba (Brazil). The gray layer of the Formation extends from 1 to 50 m deep. Although it is the most characteristic layer of the Formation, there are no studies of stabilization of these soils for urban paving purposes inthe city. Thus, this paper presents an experimental study of the stabilization of gray silt soil with Portland cement (PC) using cure times (t) of 7, 14, and 28 days. Cement contents (C) of 3, 5, 7, and 9% in relation to soil dry mass were used. After cure times, unconfined compressive strength (qu) and durability tests were performed using wet/dry cycles (W/D). The results show an increase of quwith increasing cement content, increasing molding density and increasing curing time. In addition, the durability of the mixtures increased when more cement was added. It was found that the values of quare dependent on the semi-empirical porosity/cement ratio (η/Civ). Finally, 5% is the minimum cement content for using the soil in paving purposes.

scholarly journals Characterization and Comparison Research on Composite of Alluvial Clayey Soil Modified with Fine Aggregates of Construction Waste and Fly Ash

2021 ◽  
Vol 28 (1) ◽  
pp. 83-95
Author(s):  
Qu Jili ◽  
Wang Junfeng ◽  
Batugin Andrian ◽  
Zhu Hao
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Unconfined Compressive Strength ◽  
Clayey Soil ◽  
Dry Density ◽  
Maximum Dry Density ◽  
Construction Waste ◽  
Comparison Research ◽  
Fine Aggregates ◽  
Optimum Water Content

Abstract Fine aggregates of construction waste and fly ash were selected as additives to modify the characteristics of Shanghai clayey soil as a composite. The laboratory tests on consistency index, maximum dry density, and unconfined compressive strength were carried out mainly for the purpose of comparing the modifying effect on the composite from fine aggregates of construction waste with that from fly ash. It is mainly concluded from test results that the liquid and plastic limit of the composites increase with the content of two additives. But their maximum dry density all decreases with the additive content. However, fine aggregates of construction waste can increase the optimum water content of the composites, while fly ash on the contrary. Finally, although the two additive all can increase the unconfined compressive strength of composites, fly ash has better effect. The current conclusions are also compared with previous studies, which indicates that the current research results are not completely the same as those from other researchers.

scholarly journals Investigation on cement-improved phyllite based on the vertical vibration compaction method

PLoS ONE ◽  
2021 ◽  
Vol 16 (3) ◽  
pp. e0247599
Author(s):  
Yingjun Jiang ◽  
Jiangtao Fan ◽  
Yong Yi ◽  
Tian Tian ◽  
Kejia Yuan ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Unconfined Compressive Strength ◽  
Static Pressure ◽  
Cement Content ◽  
Vertical Vibration ◽  
Pressure Method ◽  
Vibration Compaction ◽  
Modulus Of Resilience ◽  
Compaction Method

The vertical vibration compaction method (VVCM), heavy compaction method and static pressure method were used to form phyllite specimens with different degrees of weathering. The influence of cement content, compactness, and compaction method on the mechanical properties of phyllite was studied. The mechanical properties of phyllite was evaluated in terms of unconfined compressive strength (Rc) and modulus of resilience (Ec). Further, test roads were paved along an expressway in China to demonstrate the feasibility of the highly weathered phyllite improvement technology. Results show that unweathered phyllite can be used as subgrade filler. In spite of increasing compactness, phyllite with a higher degree of weathering cannot meet the requirements for subgrade filler. With increasing cement content, Rc and Ec of the improved phyllite increases linearly. Rc and Ec increase by at least 15% and 17%, respectively, for every 1% increase in cement content and by at least 10% and 6%, respectively, for every 1% increase in compactness. The higher the degree of weathering of phyllite, the greater the degree of improvement of its mechanical properties.

Modeling unconfined compressive strength of fine-grained soils: Application of pocket penetrometer for predicting soil strength

CATENA ◽  
2021 ◽  
Vol 196 ◽  
pp. 104890
Author(s):  
Fatemeh Mousavi ◽  
Ehsan Abdi ◽  
Shaaban Ghalandarayeshi ◽  
Deborah S. Page-Dumroese
Keyword(s):  
Compressive Strength ◽  
Unconfined Compressive Strength ◽  
Soil Strength ◽  
Fine Grained

Correlation between Unconfined Compressive Strength and Penetration Index Obtained from DCP Tests for Cemented Lateritic Soils

2019 ◽  
Vol 814 ◽  
pp. 399-403
Author(s):  
Anuchit Uchaipichat
Keyword(s):  
Compressive Strength ◽  
Unconfined Compressive Strength ◽  
Cement Content ◽  
Lateritic Soil ◽  
Test Results ◽  
Cone Penetration ◽  
Penetration Index ◽  
Curing Period ◽  
Cemented Soils ◽  
The Relationship

This paper presents the relationship between the dynamic cone penetration (DCP) test results and the unconfined compressive strength of lateritic cemented soils. A series of DCP tests and unconfined compressive strength was performed on lateritic cemented soil. The soils sample used in this study was lateritic soil. The test results for the DCP tests are presented in terms of penetration index. It can be observed that the penetration index decreased with increasing curing period and cement content. Moreover, the unconfined compressive strength of cemented soils increased with curing period and cement content. The relationship between unconfined compressive strength and penetration index is presented. A unique relationship for unconfined compressive strength can be obtained.

Unconfined Compressive Strength and Drying Shrinkage of Cement Treated Recycling Base at Boyolali-Kartosuro Road Rehabilitation

2012 ◽  
Vol 626 ◽  
pp. 34-38
Author(s):  
Ary Setyawan ◽  
Anastasia Muda ◽  
Sholihin As’ad
Keyword(s):  
Compressive Strength ◽  
Unconfined Compressive Strength ◽  
Cement Content ◽  
Drying Shrinkage ◽  
Reclaimed Asphalt Pavement ◽  
Reclaimed Asphalt ◽  
The Road ◽  
Road Base ◽  
Base Materials ◽  
Compressive Strength Test

Road rehabilitation and reconstruction generate large supplies of reclaimed asphalt pavement (RAP). One of the efforts to reuse the RAP is by insitu process and utilize it as road base materials. To get satisfying result from the RAP, it is necessary to add a certain amount of Ordinary Portland Cement (OPC) as stabilizer. This study investigate the potential use of OPC-stabilized RAP in road bases. Laboratory experimental method was applied by using material collected from road located at Boyolali-Kartasura as the object of the study with the cement content variations of 4%, 5% and 6% for unconfined compressive strength test (UCS) and the cement contents variation of 5% and 6% for drying shrinkage test. The range of cement contents required for unconfined compressive strength of cement treated recycling base (CTRB) are 5% to 6%. The cement content used at Boyolali - Kartosuro road rehabilitation was 5.5%. Drying shrinkage during 28 days is 805.3 micro strain for the cement content of 5% and 826.3 micro strain for the cement content of 6%. The drying shrinkage of the materials was quite high for CTRB, so that carefully design and attention need to take into account to avoid the cracks at the road base and the prospective of reflective cracking at the surface course of the road.

Influence of Curing Pressure on Unconfined Compressive Strength of Cemented Clay

2018 ◽  
Vol 928 ◽  
pp. 263-268 ◽  
Author(s):  
Anuchit Uchaipichat
Keyword(s):  
Compressive Strength ◽  
Unconfined Compressive Strength ◽  
Cement Content ◽  
Soft Clay ◽  
Peak Stress ◽  
Confining Pressure ◽  
Compression Tests ◽  
Unconfined Compression ◽  
Soil Cement ◽  
Curing Pressure

The soil-cement columns are generally installed and cured in the soft clay layers under confining pressure. The strength of the soil-cement columns may be influenced by confining pressure during curing period. In this study, the main objective was to study the influence of curing pressure on unconfined compressive strength of cemented clay. A series of unconfined compression tests was performed on a cement admixed clay sample cured under pressure values of 0 kPa (atmospheric pressure), 25kPa, 50kPa and 100 kPa using a typical unconfined compression equipment. The test samples with values of cement content of 0.5, 1.0 and 2.0 percent were cured for 28 days.The stress-strain curves obtained from all tests show a peak value of stress. The unconfined compressive strength or peak stress obviously increased with increasing cement content for all curing pressure conditions. It can be observed that the strength of samples gradually increased with curing pressure for cement content of 0.5 percent. For cement contents of 1.0 and 2.0 percent, the strengths of samples cured under pressures of 25 kPa dramatically increased from the strength of samples cured without pressure (0 kPa), however, the strengths of samples for curing pressures of 25, 50 and 100 kPa were not clearly different.

scholarly journals Cement-Stabilized Waste Sand as Sustainable Construction Materials for Foundations and Highway Roads

Materials ◽  
2019 ◽  
Vol 12 (4) ◽  
pp. 600 ◽  
Author(s):  
Faisal Shalabi ◽  
Javed Mazher ◽  
Kaffayatullah Khan ◽  
Mohammed Alsuliman ◽  
Ibrahim Almustafa ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Laser Scanning ◽  
Cement Content ◽  
Construction Material ◽  
Laser Scanning Microscopy ◽  
Tangent Modulus ◽  
Sustainable Construction ◽  
Dry Density ◽  
X Ray ◽  
Initial Tangent Modulus

In this study, cement-treated waste sand as a by-product material produced from Al-Ahsa quarries (Saudi Arabia) was experimentally tested and investigated as a base course material for the foundation of structures and roads. The study aimed to use the waste sand as a construction material by improving its strength, bearing capacity, and stiffness. The waste sand was mixed with different percentages of Portland cement content (0, 2, 4, 6, and 8%) at the maximum dry density and optimum water content of the standard Proctor compaction conditions of a non-treated sample. Unconfined compressive strength and California Bearing Ratio (CBR) tests for different curing times were conducted. X-ray diffraction (XRD), laser-scanning microscopy (LSM), and X-ray spectroscopy (XPS) were used to explore the microstructure and composition of the treated sand. The results showed that the compressive strength, initial tangent modulus, and CBR of the treated sand increase with the increase in cement content and curing time. Furthermore, good correlations were established among the strength, initial tangent modulus, and CBR. Based on the obtained results, cement-stabilized waste sand is a potential material for use in construction. This is expected to save the environment and reduce the cost of road construction.

Laboratory Experimental Research on Mix Ratio Test of Cement Soil

2013 ◽  
Vol 438-439 ◽  
pp. 197-201
Author(s):  
Xian Hua Yao ◽  
Peng Li ◽  
Jun Feng Guan
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Unconfined Compressive Strength ◽  
Cement Content ◽  
Ratio Test ◽  
Curing Time ◽  
Curing Conditions ◽  
Cement Ratio ◽  
Water Cement Ratio ◽  
Cement Soil

Based on the generalization and analysis of laboratory experimental results on mix ratio, the effects of various factors such as cement content, water-cement ratio, curing time, curing conditions and types of cement on the mechanical properties of unconfined compressive strength of cement soil are presented. Results show that the unconfined compressive strength of cement soil increases with the growing curing time, and it is greatly affected by the cement content, water-cement ratio, cement types and curing time, while the effect of curing conditions is weak with a cement content of more than 10%. Moreover, the stress-strain of the cement soil responds with the cement content and curing time, increasing curing time and cement content makes the cement soil to be harder and brittle, and leads to a larger Young's modulus.

Characterization of a cemented sand with the pulse-velocity method

2006 ◽  
Vol 43 (3) ◽  
pp. 294-309 ◽  
Author(s):  
Zahid Khan ◽  
Anwar Majid ◽  
Giovanni Cascante ◽  
D Jean Hutchinson ◽  
Parsa Pezeshkpour
Keyword(s):  
Compressive Strength ◽  
Water Content ◽  
Wave Velocity ◽  
Unconfined Compressive Strength ◽  
Void Ratio ◽  
Cement Content ◽  
Pulse Velocity ◽  
Initial Water Content ◽  
Strain Property ◽  
Cemented Sand

The effect of variation in cement content, initial water content, void ratio, and curing time on wave velocity (low-strain property) and unconfined compressive strength (large-strain property) of a cemented sand is examined in this paper. The measured pulse velocity is compared with predictions made using empirical and analytical models, which are mostly based on the published results of resonant column tests. All specimens are made by mixing silica sand and gypsum cement (2.5–20% by weight) and tested under atmospheric pressure. The wave velocity reaches a maximum at optimum water content, and it is mostly affected by the number of cemented contacts; whereas compressive strength is governed not only by the number of contacts but also by the strength of contacts. Experimental relationships are developed for wave velocity and unconfined compressive strength as functions of cement content and void ratio. Available empirical models underpredict the wave velocity (60% on average), likely because of the effect of microfractures induced by confinement during the testing. Wave velocity is found to be a good indicator of cement content and unconfined compressive strength for the conditions of this study.Key words: wave velocity, low-strain stiffness, cemented sands, elastic moduli, unconfined compressive strength.

Sign in / Sign up

Export Citation Format

Share Document