scholarly journals Effect of Submicron Glass Fiber Modification on Mechanical Properties of Short Carbon Fiber Reinforced Polymer Composite with Different Fiber Length

2020 ◽  
Vol 4 (1) ◽  
pp. 5
Author(s):  
Nhan Thi Thanh Nguyen ◽  
Obunai Kiyotaka ◽  
Okubo Kazuya ◽  
Fujii Toru ◽  
Shibata Ou ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Carbon Fiber ◽  
Glass Fiber ◽  
Fiber Length ◽  
Bending Strength ◽  
Mechanical Performance ◽  
Volume Fraction ◽  
Fiber Concentration ◽  
Static Tests ◽  
The Impact

In this research, three kinds of carbon fiber (CF) with lengths of 1, 3, and 25 mm were prepared for processing composite. The effect of submicron glass fiber addition (sGF) on mechanical properties of composites with different CF lengths was investigated and compared throughout static tests (i.e., bending, tensile, and impact), as well as the tension-tension fatigue test. The strengths of composites increased with the increase of CF length. However, there was a significant improvement when the fiber length changed from 1 to 3 mm. The mechanical performance of 3 and 25 mm was almost the same when having an equal volume fraction, except for the impact resistance. Comparing the static strengths when varying the sGF content, an improvement of bending strength was confirmed when sGF was added into 1 mm composite due to toughened matrix. However, when longer fiber was used and fiber concentration was high, mechanical properties of composite were almost dependent on the CF. Therefore, the modification effect of matrix due to sGF addition disappeared. In contrast to the static strengths, the fatigue durability of composites increased proportionally to the content of glass fiber in the matrix, regardless to CF length.

Mechanical behavior simulation: NCF/epoxy composite processed by RTM

2018 ◽  
Vol 27 (2) ◽  
pp. 66-75 ◽  
Author(s):  
Francisco Maciel Monticeli ◽  
David Daou ◽  
Mirko Dinulović ◽  
Herman Jacobus Cornelis Voorwald ◽  
Maria Odila Hilário Cioffi
Keyword(s):  
Mechanical Properties ◽  
Carbon Fiber ◽  
Mechanical Behavior ◽  
Epoxy Resin ◽  
Defect Formation ◽  
Mechanical Performance ◽  
Volume Fraction ◽  
Final Conclusion ◽  
Simulation Results ◽  
Matrix Reinforcement

Considering aeronautics requirements, academies and industries are developing matrixes and reinforcements with higher mechanical performance. The same occurs with the process where new studies focus on obtaining composites with suitable matrix/reinforcement interface. The use of epoxy resin and carbon fiber with high mechanical performance does not guarantee a composite with high mechanical properties, considering imperfections and void formation along the laminate in case of inappropriate processing parameters. The aim of this article was to analyze and quantify the mechanical behavior of polymer composite reinforced with continuous fibers using finite element methodology and postprocessing software simulation. In addition, the classical laminate theory and finite elements were used to simulate flexural and tensile tests of composite specimens. Simulation results were compared with experimental test results using a carbon fiber noncrimp fabric quadriaxial/epoxy resin composite processed by resin transfer molding. Although void volume fraction for structural materials presenting results under aeronautics requirements regarding of 2%, imperfections like lack of resin and impregnation discontinuity showed an influence in tensile and flexural experimental results. Experimental mechanical behavior decreased 10% of strength, in comparison with simulation results due to imperfection on impregnation measured by C-Scan map. Improvement in processing procedures could able to provide greater impregnation continuity, reducing defect formation and ensuring better matrix/reinforcement interface. As a final conclusion, the process plays a role as important as the characteristics of reinforcement and matrix and, consequently, the mechanical properties.

Application of Carbon Fiber-Based Composite for Electric Vehicle

2014 ◽  
Vol 896 ◽  
pp. 574-577 ◽  
Author(s):  
Miftahul Anwar ◽  
Indro Cahyono Sukmaji ◽  
Wisnu R. Wijang ◽  
Kuncoro Diharjo
Keyword(s):  
Mechanical Properties ◽  
Carbon Fiber ◽  
Glass Fiber ◽  
External Load ◽  
Volume Fraction ◽  
Fiber Composite ◽  
Impact Testing ◽  
Fiber Volume ◽  
Glass Fiber Composite ◽  
Hybrid Carbon

In the present work, we study how to improve mechanical properties of carbon fiber reinforced plastics (CFRP) in order to increase crashworthiness probability. Experimentally, hybrid carbon /glass fiber composite was made in order to get higher mechanical properties. As a results, with increasing carbon fiber volume fraction (% vol.), tensile strength and flexural strength of the composite are increased. Simulation of impact testing is also performed using data properties taken from the experiment with variation of impact forces on front bumper structure. By varying external load to the bumper, the result shows that higher thickness of hybrid carbon/glass fiber composite has always smaller stress values than thinner one. On the other hand, the displacement of hybrid carbon/glass car bumper increases linearly with increasing external load.

scholarly journals The impact of fibre processing on the mechanical properties of epoxy matrix composites and wood-based particleboard reinforced with hemp (Cannabis sativa L.) fibre

2022 ◽  
Author(s):  
Albert Hernandez-Estrada ◽  
Jörg Müssig ◽  
Mark Hughes
Keyword(s):  
Mechanical Properties ◽  
Fracture Zone ◽  
Structural Integrity ◽  
Bending Strength ◽  
Cannabis Sativa ◽  
Mechanical Performance ◽  
Epoxy Composites ◽  
Fibre Reinforcement ◽  
Fibre Bundles ◽  
The Impact

AbstractThis work investigated the impact that the processing of hemp (C. sativa L.) fibre has on the mechanical properties of unidirectional fibre-reinforced epoxy resin composites loaded in axial tension, and particleboard reinforced with aligned fibre bundles applied to one surface of the panel. For this purpose, mechanically processed (decorticated) and un-processed hemp fibre bundles, obtained from retted and un-retted hemp stems, were utilised. The results clearly show the impact of fibre reinforcement in both materials. Epoxy composites reinforced with processed hemp exhibited 3.3 times greater tensile strength when compared to the un-reinforced polymer, while for the particleboards, the bending strength obtained in those reinforced with processed hemp was 1.7 times greater than the un-reinforced particleboards. Moreover, whether the fibre bundles were processed or un-processed also affected the mechanical performance, especially in the epoxy composites. For example, the un-processed fibre-reinforced epoxy composites exhibited 49% greater work of fracture than the composites reinforced with processed hemp. In the wood-based particleboards, however, the difference was not significant. Additionally, observations of the fracture zone of the specimens showed different failure characteristics depending on whether the composites were reinforced with processed or un-processed hemp. Both epoxy composites and wood-based particleboards reinforced with un-processed hemp exhibited fibre reinforcement apparently able to retain structural integrity after the composite’s failure. On the other hand, when processed hemp was used as reinforcement, fibre bundles showed a clear cut across the specimen, with the fibre-reinforcement mainly failing at the composite's fracture zone.

scholarly journals Peningkatan Sifat Mekanik Komposit Serat Alam Limbah Sabut Kelapa (Cocofiber) yang Biodegradable

2021 ◽  
Vol 6 (1) ◽  
pp. 30-37
Author(s):  
Sri Hastuti ◽  
Herru Santosa Budiono ◽  
Diki Ilham Ivadiyanto ◽  
Muhammad Nurdin Nahar
Keyword(s):  
Mechanical Properties ◽  
Fiber Volume Fraction ◽  
Bending Strength ◽  
Natural Fiber ◽  
Volume Fraction ◽  
Fiber Composites ◽  
Coconut Fiber ◽  
Fiber Volume ◽  
Coconut Coir ◽  
The Impact

Inovasi baru serat dari sabut kelapa dimanfaatkan untuk meningkatkan nilai ekonomis dari serat sabut kelapa, oleh karena itu dirancanglah pendayagunaan serat dari sabut kelapa untuk penguat komposit dengan material serat alam yang biodegradable. Hal ini untuk mendukung penggunaan komposit yang ramah terhadap lingkungan dan mengurangi penggunaan material komposit serat sintetis yang polutan. Tujuan penelitian adalah menganalisis sifat mekanik pada komposit serat alam bermaterial serat dari sabut kelapa yang ramah lingkungan. Metode penelitian pembuatan komposit berpenguat serat dari sabut kelapa dilakukan treatment NaOH 15% selama 5 jam dan fraksi volume serat 10 %, 15 %, dan 20 %. Komposit  serat dari sabut kelapa dengan matriks UPRs 157 BQTN dengan hardener MEXPO. Pengujian mekanik dilakukan uji bending menggunakan standar ASTM D790 dan uji impak  menggunakan standar ASTM D5941.  Pengujian impak komposit serat alam menunjukkan ketangguhan impak komposit pada fraksi volume serat 20% dengan nilai 0.017588J/mm2. Hasil pengujian menunjukkan peningkatan fraksi volume serta berpengaruh terhadap peningkatan kekuatan bending komposit serat dari sabut kelapa  dengan kekuatan optimum bending pada fraksi volume serat 10% dengan nilai 44,33N/mm2. Hal ini menunjukkan peningkatan fraksi volume serat dengan perendaman NaOH 15% akan meningkatkan sifat mekanik bending dan impak komposit. Perendaman NaOH memberikan pengaruh daya serap sabut kelapa terhadap matrik Unsaturated Polyester yang dapat meningkatkan daya rekat antara penguat serat dengan matrik sehingga meningkatkan sifat mekanik bending dan impak komposit. ABSTRACT The innovation of coco fiber is used to increase the economic value of coconut coir, therefore the utilization of coconut fiber for reinforcing composites with biodegradable natural fiber material is designed. This is to support the use of composites that are friendly to the environment and reduce the use of pollutant synthetic fiber composite materials. The research objective was to analyze the mechanical properties of natural fiber composites with environmentally friendly coconut fiber as material. The research method of making fiber-reinforced composites from coconut coir was carried out by 15% NaOH treatment for 5 hours and a fiber volume fraction of 10%, 15%, and 20%. Composite fiber from coconut coir with UPRs 157 BQTN matrix with MEXPO hardener. Mechanical testing is carried out using the ASTM D790 standard and the impact test using the ASTM D5941 standard. The impact test of natural fiber composites showed the impact toughness of the composite at a fiber volume fraction of 20% with a value of 0.017588 J/ mm2. The test results showed an increase in volume fraction and an effect on the increase in the bending strength of coconut fiber composites with the optimum bending strength at a fiber volume fraction of 10% with a value of 44.33N /mm2. This shows that the increase in fiber volume fraction by immersion in 15% NaOH will increase the bending mechanical properties and the impact of the composite. Soaking NaOH has an effect on the absorption power of coconut coir on the Unsaturated Polyester matrix which can increase the adhesion between the fiber reinforcement and the matrix thereby increasing the bending mechanical properties and impact of the composite.

The Effect of Fibers’ Length Distribution and Concentration on Rheological and Mechanical Properties of Glass Fiber–Reinforced Polypropylene Composite

2021 ◽  
pp. 152808372110432
Author(s):  
Fatemeh Asoodeh ◽  
Mohammad Aghvami-Panah ◽  
Saeed Salimian ◽  
Mohammadreza Naeimirad ◽  
Hamed khoshnevis ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Flexural Strength ◽  
Glass Fiber ◽  
Fiber Length ◽  
Volume Fraction ◽  
Length Distribution ◽  
Second Phase ◽  
Distribution Factor ◽  
Fiber Length Distribution ◽  
Extrusion Processing

This article aims to investigate the effect of dispersion and uniformity of fiber length distribution on the rheological and mechanical behavior of polypropylene reinforced with short glass fiber. The composites were prepared through melt compounding with three various glass fiber concentrations using a twin-screw extruder. Multiple extrusion processing was used to alter and manipulate the fibers’ length inside the composites. The fiber length distribution was analyzed via the photomicrograph technique. Rheological measurements indicated that the molten samples were visco-plastic fluids and the Herschel–Bulkley model is the best model for fitting on the rheological behavior diagram. Variables of the fitted model are noticeably altered by the fiber length distribution. Moreover, rheological assessments revealed that the non-Newtonian behavior of the molten composites significantly diminished after the second extrusion processing, while it did not have much effect on the fiber length reduction. In the second phase, tensile and flexural properties were determined to detect the mechanical properties. The results indicated that the tensile strength of the composite has a direct relation with the fiber length distribution factor while the flexural strength is independent of fiber length. Furthermore, the highest tensile and flexural strength attained from the composite containing the highest fiber volume fraction.

Mechanical properties and fiber characteristics of glass fiber/carbon fiber reinforced polyethylene terephthalate hybrid composites fabricated by direct fiber feeding injection molding

2018 ◽  
Vol 38 (6) ◽  
pp. 513-523 ◽  
Author(s):  
Wiranphat Thodsaratpreeyakul ◽  
Putinun Uawongsuwan ◽  
Akio Kataoka ◽  
Takanori Negoro ◽  
Hiroyuki Hamada
Keyword(s):  
Mechanical Properties ◽  
Carbon Fiber ◽  
Injection Molding ◽  
Glass Fiber ◽  
Polyethylene Terephthalate ◽  
Fiber Orientation ◽  
Mechanical Performance ◽  
Hybrid Composites ◽  
Fiber Distribution ◽  
Volume Fractions

Abstract Improving the applicability of polyethylene terephthalate (PET) by carbon fiber/glass fiber reinforcement is of great interest. Glass fiber (GF)/carbon fiber (CF)/PET hybrid composites were fabricated by direct fiber feeding injection molding (DFFIM) process. The aim of DFFIM is to obtain longer fibers in composites in order to improve their mechanical properties. In this study, the mechanical properties of GF/PET composites fabricated by conventional injection molding and hybrid GF/CF/PET composites fabricated by DFFIM process were investigated. The influence of GF and CF volume fractions on fiber distribution, fiber orientation, and fiber length is discussed. Fiber distribution status was quantitatively measured by the fiber distribution index. Fiber agglomeration problem was observed by scanning electron microscopy. The results indicate that incorporating CF in GF/CF/PET hybrid composites by the DFFIM process greatly enhances mechanical performance even when only a small amount of CF is added. Too high GF content leads to less effective CF hybridization because it causes poor fiber distribution and poor fiber orientation and intensifies fiber attrition. The ideal volume fractions of GF and CF for fabricating GF/CF/PET hybrid composites by using DFFIM are provided.

scholarly journals Influence of Air Plasma Pretreatments on Mechanical Properties in Metal-Reinforced Laminated Wood

2022 ◽  
Vol 8 ◽  
Author(s):  
Sebastian Dahle ◽  
Kavyashree Srinivasa ◽  
Jure Žigon ◽  
Arnaud Maxime Cheumani Yona ◽  
Georg Avramidis ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Bending Strength ◽  
Mechanical Performance ◽  
Mechanical Load ◽  
Urea Formaldehyde ◽  
Air Plasma ◽  
Adhesive Systems ◽  
Plasma Treatments ◽  
Structural Applications ◽  
The Impact

The use of wood-based materials in building and construction is constantly increasing as environmental aspects and sustainability gain importance. For structural applications, however, there are many examples where hybrid material systems are needed to fulfil the specific mechanical requirements of the individual application. In particular, metal reinforcements are a common solution to enhance the mechanical properties of a wooden structural element. Metal-reinforced wood components further help to reduce cross-sectional sizes of load-bearing structures, improve the attachment of masonry or other materials, enhance the seismic safety and tremor dissipation capacity, as well as the durability of the structural elements in highly humid environments and under high permanent mechanical load. A critical factor to achieve these benefits, however, is the mechanical joint between the different material classes, namely the wood and metal parts. Currently, this joint is formed using epoxy or polyurethane (PU) adhesives, the former yielding highest mechanical strengths, whereas the latter presents a compromise between mechanical and economical constraints. Regarding sustainability and economic viability, the utilization of different adhesive systems would be preferable, whereas mechanical stabilities yielded for metal-wood joints do not permit for the use of other common adhesive systems in such structural applications. This study extends previous research on the use of non-thermal air plasma pretreatments for the formation of wood-metal joints. The plasma treatments of Norway spruce [Picea abies (L.) Karst.] wood and anodized (E6/EV1) aluminum AlMgSi0.5 (6060) F22 were optimized, using water contact angle measurements to determine the effect and homogeneity of plasma treatments. The adhesive bond strengths of plasma-pretreated and untreated specimens were tested with commercial 2-component epoxy, PU, melamine-urea formaldehyde (MUF), polyvinyl acetate (PVAc), and construction adhesive glue systems. The influence of plasma treatments on the mechanical performance of the compounds was evaluated for one selected glue system via bending strength tests. The impact of the hybrid interface between metal and wood was isolated for the tests by using five-layer laminates from three wood lamellae enclosing two aluminum plates, thereby excluding the influence of congeneric wood-wood bonds. The effect of the plasma treatments is discussed based on the chemical and physical modifications of the substrates and the respective interaction mechanisms with the glue systems.

Study on Mechanical Properties of GF/PVC with CPE and ACR

2013 ◽  
Vol 788 ◽  
pp. 81-84 ◽  
Author(s):  
Sha Sha Wang ◽  
Ke Juan Chen
Keyword(s):  
Mechanical Properties ◽  
Impact Strength ◽  
Glass Fiber ◽  
Bending Strength ◽  
Breaking Elongation ◽  
Tensile And Bending Strength ◽  
The Impact

Reinforce the strength of PVC by adding glass fiber, study the mechanical properties of PVC on different contents of glass fiber. With the increasing contents of glass fiber, the tensile and bending strength, impact strength are increased, but the breaking elongation is decreased. In order to further improve the toughness of PVC, do research on how to toughen the GF/PVC alloy, study the influence of CPE and ACR on GF/PVC. Use the method of blending modification of glass fiber, PVC and modifiers, significantly increase the impact strength and breaking elongation while maintaining the strength. Compare the influence of CPE and ACR on GF/PVC properties, make excellent strengthened PVC material.

Diallyl Orthophthalate(DAOP) Resin as a Reactive Plasticizer for Optimizing Glass-fiber/PVC Interface and Reactive Kinetics

2011 ◽  
Vol 239-242 ◽  
pp. 408-412 ◽  
Author(s):  
Peng Wen ◽  
Qi Lin Mei ◽  
Xiao Qin Yue ◽  
Meng Xin Liu
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Impact Toughness ◽  
Glass Fiber ◽  
Bending Strength ◽  
Sem Images ◽  
Melt Compounding ◽  
The Impact

To improve brittleness and optimize interface of glass-fiber/PVC composites, reinforcing and toughening technologies for glass-fiber/PVC composites were studied. Influences of glass-fiber and diallyl orthophthalate(DAOP) resin on their mechanical properties were observed. Diallyl orthophthalate(DAOP) resin was blended with PVC in various weight ratios by melt compounding. The compatibility between diallyl orthophthalate(DAOP) resin and PVC resin was analysed by measuring the impact toughness, tensile strength and bending strength. The results clarified that each mechanical properties improved, in addition to,SEM images show that the interface of glass-fiber/PVC composites added with DAOP was much closer , PVC resin surrounds completely the glass-fiber.

scholarly journals Mechanical properties of composite material laminates reinforced by woven and non-woven glass fibers

2020 ◽  
Vol 175 ◽  
pp. 12005 ◽  
Author(s):  
Amer Karnoub ◽  
Hajian Huang ◽  
Imad Antypas
Keyword(s):  
Mechanical Properties ◽  
Composite Material ◽  
Glass Fiber ◽  
Mechanical Characteristics ◽  
Polyester Resin ◽  
Mechanical Performance ◽  
Glass Fibers ◽  
Mechanical Tests ◽  
Impact Behavior ◽  
The Impact

The purpose of this work is to study the mechanical characteristics in 3-point bending and in traction; static; and the impact behavior of three specimens of laminates made of glass fiber and polyester resin non-woven and woven, with the aim of using them in the repair of boat hulls and enhancing their value in the naval industry. Three types of laminates were developed by contact molding. These different specimens of laminates made of woven, non-woven and combined glass fiber (woven and non-woven) were subjected to mechanical tests (traction and 3-point bending). Analysis of the results of the tests carried out on these three types of laminate shows that one specimen stands out and gives higher mechanical performance than the othertwo.

Sign in / Sign up

Export Citation Format

Share Document