scholarly journals Hybrid Manufacturing and Experimental Testing of Glass Fiber Enhanced Thermoplastic Composites

2019 ◽  
Vol 3 (4) ◽  
pp. 96 ◽  
Author(s):  
Javaid Butt ◽  
Yasasween Hewavidana ◽  
Vahaj Mohaghegh ◽  
Shabnam Sadeghi-Esfahlani ◽  
Hassan Shirvani
Keyword(s):  
Tensile Strength ◽  
Glass Fiber ◽  
Tensile Testing ◽  
Experimental Testing ◽  
Microstructural Analysis ◽  
Optimal Number ◽  
Fused Deposition Modelling ◽  
Gfrp Composites ◽  
Fused Deposition ◽  
Industrial Sectors

Additive Manufacturing (AM) is gaining enormous attention from academic and industrial sectors for product development using different materials. Fused Deposition Modelling (FDM) is a popular AM method that works with thermoplastics. This process offers benefits of customisation both in terms of hardware and software in the case of desktop-based FDM systems. Enhancement of mechanical properties for the traditional thermoplastic material is a widely researched area and various materials have been added to achieve this goal. This paper focuses on the manufacture of glass fiber reinforced plastic (GFRP) composites using Hybrid Fused Deposition Modelling (HFDM). Commonly available polylactic acid or polylactide (PLA) material was inter-laced with 0.03 mm thick glass fiber sheets to manufacture GFRP products followed by tensile testing. This was done to investigate whether adding more layers increases the tensile strength of the GFRP products or not. Furthermore, the maximum number of glass fiber layers that can be added to the 4 mm thick specimen was also identified. This was done to demonstrate that there is an optimal number of glass fiber layers that can be added as after this optimal number, the tensile strength start to deteriorate. Microstructural analysis was undertaken after tensile testing followed by ultrasonic testing to assess the uniformity of the GFRP composites.

scholarly journals Experimental testing of PLA biodegradable thermoplastic in the frame of 3D printing FDM technology

2018 ◽  
Vol 157 ◽  
pp. 06001
Author(s):  
Juraj Beniak ◽  
Peter Križan ◽  
Miloš Matúš ◽  
Michal Šajgalík
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
3D Printing ◽  
Experimental Testing ◽  
3D Models ◽  
Fused Deposition Modelling ◽  
Suitable Material ◽  
Fused Deposition ◽  
Plastic Materials ◽  
Melted Material

In the present time there are many different plastic materials and composite materials suitable for 3D printing by deposition of semi-melted material. The proper selection of correct material with suitable material properties is dependent on the situation how the produced 3D model should be used. If we need to take into account just the visual look of used material or also the mechanical properties as strength is important for loaded models for final use. The aim of this paper is to publish outputs of experimental testing for 3D models from selected materials with regards to mechanical properties of produced testing parts. Produced 3D models are from PLA biodegradable thermoplastic. Models are prepared on Fused Deposition Modelling (FDM) 3D printer. Testing is based on prepared full factors experiment with four factors on its two levels. Measured values are Tensile strength of PLA testing 3D models. In the same time there are gathered information regarding the 3D printing process and compared to measured tensile strength values for each sent of testing parts. All the measured data are statistically evaluated also by Analysis of Variance (ANOVA method).

scholarly journals The Influence of Manufacturing Parameters on the Mechanical Behaviour of PLA and ABS Pieces Manufactured by FDM: A Comparative Analysis

Materials ◽  
2018 ◽  
Vol 11 (8) ◽  
pp. 1333 ◽  
Author(s):  
Adrián Rodríguez-Panes ◽  
Juan Claver ◽  
Ana Camacho
Keyword(s):  
Tensile Strength ◽  
Mechanical Behaviour ◽  
Mechanical Performance ◽  
Acrylonitrile Butadiene Styrene ◽  
Polymer Materials ◽  
Fused Deposition Modelling ◽  
Fused Deposition ◽  
Layer Orientation ◽  
Lower Variability

This paper presents a comparative study of the tensile mechanical behaviour of pieces produced using the Fused Deposition Modelling (FDM) additive manufacturing technique with respect to the two types of thermoplastic material most widely used in this technique: polylactide (PLA) and acrylonitrile butadiene styrene (ABS). The aim of this study is to compare the effect of layer height, infill density, and layer orientation on the mechanical performance of PLA and ABS test specimens. The variables under study here are tensile yield stress, tensile strength, nominal strain at break, and modulus of elasticity. The results obtained with ABS show a lower variability than those obtained with PLA. In general, the infill percentage is the manufacturing parameter of greatest influence on the results, although the effect is more noticeable in PLA than in ABS. The test specimens manufactured using PLA perform more rigidly and they are found to have greater tensile strength than ABS. The bond between layers in PLA turns out to be extremely strong and is, therefore, highly suitable for use in additive technologies. The methodology proposed is a reference of interest in studies involving the determination of mechanical properties of polymer materials manufactured using these technologies.

Deriving Infill Design of Fused Deposition Modelled Parts From Predicted Stress Profiles

2016 ◽  
Author(s):  
James A. Gopsill ◽  
Ben J. Hicks
Keyword(s):  
Process Time ◽  
Fused Deposition Modelling ◽  
Stress Profile ◽  
3 Dimensional ◽  
Fused Deposition ◽  
Industrial Sectors ◽  
Pattern Structures ◽  
Initial Work ◽  
Bending Loads ◽  
Multiple Materials

The use of Fused Deposition Modelling (FDM) is increasing rapidly in both the commercial and industrial sectors as a means of rapidly prototyping geometrically complex parts. Particular affordances of FDM include the reduction of waste material during manufacture, the use of multiple materials within a single manufacturing process and the ability to manipulate the internal geometry of a part. The latter of which has seen the generation of many 2-dimensional repeating pattern structures such as square, rectilinear and hexagonal, as well as an emerging field of 3-dimensional structures. Although these patterns have provided stiffness and rigidity whilst reducing the production time of FDM prototypes, many do not consider the actual loading conditions of the part in-situ, where it is argued that further significant gains in the performance could be achieved. This includes further reduction in process time and increased part functionality. Thus, this paper presents initial work into the generation of an infill that is derived from the predicted stress profile for the part. This has been achieved through the post-processing of Finite Element (FE) models to identify the stress profile. Interpolation across these profiles leads to a set of aligned Bézier splines that enable the transmission of force and are also able to be manufactured using FDM. These splines are embedded within the typical slicing procedure of a part ahead of being manufactured on a FDM machine. Initial results from parts designed to support three-point bending loads show a 79% increase in the stiffness of the part alongside a consistent and repeatable mode of failure when compared to the commonly used honeycomb infill design.

scholarly journals Tensile and Bending Strength Improvements in PEEK Parts Using Fused Deposition Modelling 3D Printing Considering Multi-Factor Coupling

Polymers ◽  
2020 ◽  
Vol 12 (11) ◽  
pp. 2497 ◽  
Author(s):  
Yao Li ◽  
Yan Lou
Keyword(s):  
Tensile Strength ◽  
3D Printing ◽  
Tensile Properties ◽  
Bending Strength ◽  
Utilization Rate ◽  
Fused Deposition Modelling ◽  
Fused Deposition ◽  
Molded Parts ◽  
Injection Molded ◽  
Printing Direction

Compared with laser-based 3D printing, fused deposition modelling (FDM) 3D printing technology is simple and safe to operate and has a low cost and high material utilization rate; thus, it is widely used. In order to promote the application of FDM 3D printing, poly-ether-ether-ketone (PEEK) was used as a printing material to explore the effect of multi-factor coupling such as different printing temperatures, printing directions, printing paths, and layer thicknesses on the tensile strength, bending strength, crystallinity, and grain size of FDM printed PEEK parts. The aim was to improve the mechanical properties of the 3D printed PEEK parts and achieve the same performance as the injection molded counterparts. The results show that when the thickness of the printed layer is 0.1 mm and the printing path is 180° horizontally at 525 °C, the tensile strength of the sample reaches 87.34 MPa, and the elongation reaches 38%, which basically exceeds the tensile properties of PEEK printed parts reported in previous studies and is consistent with the tensile properties of PEEK injection molded parts. When the thickness of the printed layer is 0.3 mm, the printing path is 45°, and with vertical printing direction at a printing temperature of 525 °C, the bending strength of the sample reaches 159.2 MPa, which exceeds the bending performance of injection molded parts by 20%. It was also found that the greater the tensile strength of the printed specimen, the more uniform the size of each grain, and the higher the crystallinity of the material. The highest crystallinity exceeded 30%, which reached the crystallinity of injection molded parts.

Localised Pre-Heating to Improve Inter-Layer Delamination Strength in Fused Deposition Modelling

2019 ◽  
Author(s):  
Andrew Aitchison ◽  
Qing Wang
Keyword(s):  
Tensile Strength ◽  
Thermal Energy ◽  
Fused Deposition Modeling ◽  
Acrylonitrile Butadiene Styrene ◽  
Additive Manufacture ◽  
Fused Deposition Modelling ◽  
Print Quality ◽  
Air Gaps ◽  
Fused Deposition ◽  
Air Temperatures

Abstract Additive manufacture, specifically Fused Deposition Modeling (FDM), is an advancing manufacture method opening up new possibilities in design previously impossible to machine, in a relatively affordable way. However, its use in functional products is limited due to anisotropic strength and reduced strength from injection molded components. This paper aims to increase the tensile strength of Acrylonitrile Butadiene Styrene (ABS) in the weakest direction (Z axis), where poor interlayer fusion and air gaps between extruded trails reduce strength. Extra thermal energy was applied to the top surface layer during the printing process (through hot air) to encourage more polymer chain diffusion across the boundary, and spreading out to fill air gaps. Multiple tensile test samples were printed at a variety of heat levels. The ultimate tensile strength σuts was plotted against these temperatures and a weak positive correlation was found. However, only air temperatures above 81°C increased strength past the control to a maximum of 1.4MPa. Heat application has proven to increase tensile strength, but needs to be applied with a more precise method, to the boundary interface, to allow greater thermal energy transfer without sacrificing print quality.

Anisotropy Evaluation of Different Raster Directions, Spatial Orientations, and Fill Percentage of 3D Printed PETG Tensile Test Specimens

2019 ◽  
Vol 821 ◽  
pp. 167-173 ◽  
Author(s):  
Muammel M. Hanon ◽  
Róbert Marczis ◽  
László Zsidai
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Tensile Test ◽  
Fused Deposition Modelling ◽  
Elongation At Break ◽  
Know How ◽  
Fused Deposition ◽  
Test Pieces ◽  
3D Printed ◽  
Fill Percentage

In this paper, the mechanical properties of Polyethylene terephthalate-glycol (PETG) tensile test specimens have been investigated. The test pieces were prepared using fused deposition modelling (FDM) 3D printing technology. Three print settings were examined which are: raster direction angles, print orientations, and infill percentage and patterns in order to evaluate the anisotropy of objects when employing FDM print method. The variations in stress-strain curves, tensile strength values and elongation at break among the tested samples were studied and compared. Illustration for the broken specimens after the tensile test was accomplished to know how the test pieces printed with various parameters were fractured. A comparison with some previous results regarding the elongation at break has been carried out.

scholarly journals Influence of the Print Layer Height in FDM Technology on the Rolling Force Value and the Print Time

2019 ◽  
Vol 23 (4) ◽  
pp. 1-9
Author(s):  
Wojciech Kiński ◽  
Paweł Pietkiewicz
Keyword(s):  
Tensile Strength ◽  
Rolling Force ◽  
Single Layer ◽  
Fused Deposition Modelling ◽  
Strength Parameters ◽  
Layer Height ◽  
Fused Deposition ◽  
Made In

AbstractThe paper presents a method and results of breaking of samples that undergo elongation, printed in the FDM (Fused Deposition Modelling) technology including various height of a layer. A method of description of the FDM print was described. A developed methodology of research was presented − it was analogous to the research on breaking steel samples. The aim of the research was investigation of the height of a single layer of print on the strength parameters of the produced object. The studies on samples printed with two types of filling were made. The obtained results were set and compared. Based on the research that was carried out, it may be concluded that the tensile strength of samples made in the FDM print technology is proportional to the thickness of a single layer of print.

scholarly journals Influence of the 3D Printing Process Settings on Tensile Strength of PLA and HT-PLA

2020 ◽  
Vol 65 (1) ◽  
pp. 38-46
Author(s):  
Muammel M. Hanon ◽  
Róbert Marczis ◽  
László Zsidai
Keyword(s):  
Tensile Strength ◽  
3D Printing ◽  
Tensile Test ◽  
Fill Factor ◽  
Fused Deposition Modelling ◽  
Printing Technology ◽  
Elongation At Break ◽  
Fused Deposition ◽  
Test Pieces ◽  
Insight Into

Fused Deposition Modelling (FDM) is presently the most common utilized 3D printing technology. Since this printing technology makes the bodies anisotropic, therefore, investigate the process with different settings is worthwhile. Tensile test specimens of two plastics have been carried out to examine the mechanical properties. Polylactic acid (PLA) and High Temperature PLA (HT-PLA) are the used materials for this purpose. A total of seventy-two test pieces of the two used polymers were printed and evaluated. Three parameters were examined in twelve different settings when printing the tensile test specimens. The considered settings are; six raster directions, three build orientations and two filling factors. The differences in stress-strain curves, tensile strength values and elongation at break were compared among the tested samples. The broken specimens after the tensile test are illustrated, which gave insight into how the test pieces printed with different parameters were fractured. The optimum printing setting is represented at crossed 45/−45° raster direction, X orientation and 100 % fill factor, where the highest tensile strength of 59.7 MPa at HT-PLA and the largest elongation of about 3.5 % at PLA were measured.

Experimental Testing of Materials Used in Fused Deposition Modeling Rapid Prototyping Technology

2013 ◽  
Vol 740 ◽  
pp. 597-602 ◽  
Author(s):  
Ludmila Novakova-Marcincinova ◽  
Jozef Novak-Marcincin
Keyword(s):  
Rapid Prototyping ◽  
Fused Deposition Modeling ◽  
Experimental Testing ◽  
Acrylonitrile Butadiene Styrene ◽  
Advanced Materials ◽  
Fused Deposition Modelling ◽  
Initial State ◽  
Fused Deposition ◽  
Materials Used ◽  
Solid Liquid

In this paper are presented information about common and advanced materials used for manufacturing of products by Fused Deposition Modelling (FDM) rapid prototyping technology. In different rapid prototyping technologies the initial state of material can come in either solid, liquid or powder state. The current range materials include paper, nylon, wax, resins, metals and ceramics. In FDM are mainly used as basic materials ABS - Acrylonitrile Butadiene Styrene, polyamide, polycarbonate, polyethylene and polypropylene. Main part of the paper is focused on experimental testing of rapid prototyping materials realized by different research teams and presents outputs of testing of ABS material in FDM technology realized by authors.

Sign in / Sign up

Export Citation Format

Share Document