scholarly journals The Effect of Heat Treatment on the Structure of Zeolite A

Materials ◽  
2021 ◽  
Vol 14 (16) ◽  
pp. 4642
Author(s):  
Magdalena Katarzyna Król ◽  
Piotr Jeleń
Keyword(s):  
Crystal Structure ◽  
Heat Treatment ◽  
Spectroscopic Method ◽  
Research Work ◽  
Dehydration Process ◽  
Zeolite A ◽  
Heating Water ◽  
Structural Tests ◽  
Drift Spectra

Knowledge about the thermal properties of zeolites is extremely important due to their potential application in the chemical industry. In this work, the thermal stability and the dehydration process of zeolite A were investigated by in situ high temperature Fourier transform infrared spectroscopy. The progress of thermal decomposition that zeolite A underwent during the controlled temperature increase in the range of 25–600 °C was determined by the DRIFT spectroscopic method. Infrared spectra are presented and discussed for this compound on the basis of the crystal structure. Based on the courses of the obtained DRIFT spectra, it was found that, during heating, water was gradually removed from the structure of the material, followed by dehydration and formation of hydrogen bonds. It was established that the process of thermal degradation began as early as 550 °C. The analysis of the obtained results of structural tests can be repeated on other materials from the zeolite group and complements the research work on the thermal analysis of these materials.

scholarly journals Thermo-mechanical Processing for In-situ Cu-based Composites

2021 ◽  
Vol 2125 (1) ◽  
pp. 012057
Author(s):  
Xiaochun Sheng ◽  
Ying Jin ◽  
Mulin Li ◽  
Qi Shen ◽  
Zhi Shen ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Hot Deformation ◽  
Cold Deformation ◽  
Research Work ◽  
Main Role ◽  
Mechanical Processing ◽  
Final Heat ◽  
Initial Heat ◽  
Initial Heat Treatment

Abstract In-situ Cu-based composites have been investigated extensively over the past decades because of their good conductivity and high strength. The preparation technologies of in-situ Cu-based composites mainly include casting of Cu alloys, initial heat treatment, hot deformation, cold deformation, intermediate and final heat treatment. This paper primarily researched the effect of thermo-mechanical processing such as initial heat treatment, hot deformation, cold deformation, intermediate and final heat treatments on the property and microstructure of in-situ Cu-based composites, analyzed the main role and mechanism of each thermo-mechanical processing, summarized the related research work and achievements, and prospected the future main research directions of the thermo-mechanical processing for in-situ Cu-based composites.

Microstructural and Mechanical Behaviour Evaluation of Mg-Al-Zn Alloy Friction Stir Welded Joint

2020 ◽  
Vol 17 (3) ◽  
pp. 8150-8159
Author(s):  
Kulwant Singh ◽  
Gurbhinder Singh ◽  
Harmeet Singh
Keyword(s):  
Heat Treatment ◽  
Friction Stir Welding ◽  
Magnesium Alloys ◽  
Mechanical Performance ◽  
Fuel Efficiency ◽  
Research Work ◽  
Grain Structure ◽  
Tensile Fracture ◽  
Friction Stir ◽  
The Impact

The weight reduction concept is most effective to reduce the emissions of greenhouse gases from vehicles, which also improves fuel efficiency. Amongst lightweight materials, magnesium alloys are attractive to the automotive sector as a structural material. Welding feasibility of magnesium alloys acts as an influential role in its usage for lightweight prospects. Friction stir welding (FSW) is an appropriate technique as compared to other welding techniques to join magnesium alloys. Field of friction stir welding is emerging in the current scenario. The friction stir welding technique has been selected to weld AZ91 magnesium alloys in the current research work. The microstructure and mechanical characteristics of the produced FSW butt joints have been investigated. Further, the influence of post welding heat treatment (at 260 °C for 1 h) on these properties has also been examined. Post welding heat treatment (PWHT) resulted in the improvement of the grain structure of weld zones which affected the mechanical performance of the joints. After heat treatment, the tensile strength and elongation of the joint increased by 12.6 % and 31.9 % respectively. It is proven that after PWHT, the microhardness of the stir zone reduced and a comparatively smoothened microhardness profile of the FSW joint obtained. No considerable variation in the location of the tensile fracture was witnessed after PWHT. The results show that the impact toughness of the weld joints further decreases after post welding heat treatment.

Single Crystal Growth of High-Pressure Phases of Ice and Salt Hydrate Far Below the Original Melting Point by Mixing Alcohol: Crystal Structure Determination of Magnesium Chloride Heptahydrate

2020 ◽  
Author(s):  
Keishiro Yamashita ◽  
Kazuki Komatsu ◽  
Hiroyuki Kagi
Keyword(s):  
Crystal Structure ◽  
High Pressure ◽  
Crystal Growth ◽  
Single Crystal ◽  
Room Temperature ◽  
Growth Technique ◽  
Salt Hydrate ◽  
X Ray

An crystal-growth technique for single crystal x-ray structure analysis of high-pressure forms of hydrogen-bonded crystals is proposed. We used alcohol mixture (methanol: ethanol = 4:1 in volumetric ratio), which is a widely used pressure transmitting medium, inhibiting the nucleation and growth of unwanted crystals. In this paper, two kinds of single crystals which have not been obtained using a conventional experimental technique were obtained using this technique: ice VI at 1.99 GPa and MgCl<sub>2</sub>·7H<sub>2</sub>O at 2.50 GPa at room temperature. Here we first report the crystal structure of MgCl2·7H2O. This technique simultaneously meets the requirement of hydrostaticity for high-pressure experiments and has feasibility for further in-situ measurements.

The Nature of Chemisorbed CO2 in Zeolite A

2019 ◽  
Author(s):  
Przemyslaw Rzepka ◽  
Zoltán Bacsik ◽  
Andrew J. Pell ◽  
Niklas Hedin ◽  
Aleksander Jaworski
Keyword(s):  
Solid State ◽  
Ir Spectroscopy ◽  
Quantum Chemical Calculations ◽  
Quantum Chemical ◽  
Surface Coverage ◽  
Gas Mixtures ◽  
Mas Nmr ◽  
Significant Fraction ◽  
Zeolite A

Formation of CO<sub>3</sub><sup>2-</sup> and HCO<sub>3</sub><sup>-</sup> species without participation of the framework oxygen atoms upon chemisorption of CO<sub>2</sub> in zeolite |Na<sub>12</sub>|-A is revealed. The transfer of O and H atoms is very likely to have proceeded via the involvement of residual H<sub>2</sub>O or acid groups. A combined study by solid-state <sup>13</sup>C MAS NMR, quantum chemical calculations, and <i>in situ</i> IR spectroscopy showed that the chemisorption mainly occurred by the formation of HCO<sub>3</sub><sup>-</sup>. However, at a low surface coverage of physisorbed and acidic CO<sub>2</sub>, a significant fraction of the HCO<sub>3</sub><sup>-</sup> was deprotonated and transformed into CO<sub>3</sub><sup>2-</sup>. We expect that similar chemisorption of CO<sub>2</sub> would occur for low-silica zeolites and other basic silicates of interest for the capture of CO<sub>2</sub> from gas mixtures.

scholarly journals Memory Effect on a LDH/zeolite A Composite: An XRD In Situ Study

Materials ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2102
Author(s):  
Breno G. P. Bezerra ◽  
Lindiane Bieseki ◽  
Mariele I. S. de Mello ◽  
Djalma R. da Silva ◽  
Cristiane B. Rodella ◽  
...  
Keyword(s):  
Memory Effect ◽  
Inert Atmosphere ◽  
Effect Study ◽  
Physical Mixture ◽  
Zeolite A ◽  
Three Samples ◽  
In Situ Experiments ◽  
Double Hydroxide ◽  
Rehydration Process

In this memory effect study, hydrotalcite-type compounds in the lamellar double hydroxide-like (LDH)/zeolite A composite material were analyzed using X-Ray Diffration XRD) in situ experiments. Three samples were analyzed: Al,Mg-LDH, Al,Mg-LDH/ZA composite, and a physical mixture (50/50 wt%) of zeolite A and Al,Mg-LDH. The Al,Mg-LDH sample was treated at 500 °C in an O2 atmosphere and subsequently rehydrated. The Al,Mg-LDH/ZA composites had three treatments: one was performed at 300 °C in a He atmosphere, and two treatments were performed with an O2 atmosphere at 300 and 500 °C. In the physical mixture, two treatments were carried out under O2 flow at 500 °C and under He flow at 300 °C. Both went through the rehydration process. All samples were also analyzed by energy dispersive spectroscopy (EDS) and scanning electron microscopy (SEM). The results show that the LDH phase in the Al,Mg-LDH/ZA compounds has memory effects, and thus, the compound can be calcined and rehydrated. For the LDH in the composite, the best heat treatment system is a temperature of 300 °C in an inert atmosphere.

Mechanical Properties of Pyrolytic "SiOCN" Thin Coatings

1993 ◽  
Vol 308 ◽  
Author(s):  
Sandrine Bec ◽  
André Tonck ◽  
Jean-Luc Loubet
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Ceramic Coatings ◽  
Optical Observation ◽  
Thin Coatings ◽  
Polymer Precursors ◽  
Polymeric State

ABSTRACTPyrolysis of polymer precursors (polysilazane) is a technologically and economically interesting way to produce thin ceramic coatings. However, many cracks appear and decohesion occurs during pyrolysis when the ceramic coatings (SiOCN) are thicker than 0.5 micrometers. In order to understand these cracking phenomena, the coatings are mechanically characterized by nanoindentation at different stages of the pyrolysis heat treatment.During pyrolysis, the cracking temperature is detected by in-situ optical observation. The thickness of the coatings varies during pyrolysis from 3 micrometers at the polymeric state to 1 micrometer at the ceramic state. The coatings' properties, hardness and Young's modulus are evaluated after heat treatment, taking into account the substrate's influence. A large variation of these properties occurs at the cracking temperature. Both the hardness and the Young's modulus are multiplied by a factor of 10. By analysing these results, we show that cracking is correlated with the evolution of the coatings' mechanical properties during the transformation.

PHASE TRANSITION IN LAYERED PEROVSKITE LIKE MANGANATE Ca3Mn2O7 UNDER HIGH PRESSURE

2001 ◽  
Vol 15 (18) ◽  
pp. 2491-2497 ◽  
Author(s):  
J. L. ZHU ◽  
L. C. CHEN ◽  
R. C. YU ◽  
F. Y. LI ◽  
J. LIU ◽  
...  
Keyword(s):  
Crystal Structure ◽  
High Pressure ◽  
Diamond Anvil Cell ◽  
The Other ◽  
Layered Perovskite ◽  
X Ray Diffraction ◽  
Two Phase ◽  
X Ray ◽  
Diamond Anvil

In situ high pressure energy dispersive X-ray diffraction measurements on layered perovskite-like manganate Ca 3 Mn 2 O 7 under pressures up to 35 GPa have been performed by using diamond anvil cell with synchrotron radiation. The results show that the structure of layered perovskite-like manganate Ca 3 Mn 2 O 7 is unstable under pressure due to the easy compression of NaCl-type blocks. The structure of Ca 3 Mn 2 O 7 underwent two phase transitions under pressures in the range of 0~35 GPa. One was at about 1.3 GPa with the crystal structure changing from tetragonal to orthorhombic. The other was at about 9.5 GPa with the crystal structure changing from orthorhombic back to another tetragonal.

Sign in / Sign up

Export Citation Format

Share Document