scholarly journals Lateral Buckling Theory and Experimental Study on Pipe-in-Pipe Structure

Metals ◽  
2019 ◽  
Vol 9 (2) ◽  
pp. 185 ◽  
Author(s):  
Zechao Zhang ◽  
Hongbo Liu ◽  
Zhihua Chen
Keyword(s):  
Experimental Study ◽  
Finite Element ◽  
Thermal Loading ◽  
Oil And Gas ◽  
Critical Force ◽  
Lateral Buckling ◽  
Element Analysis ◽  
Theoretical Derivation ◽  
Initial Imperfections ◽  
Global Buckling

With the increasing depth of marine oil and gas exploitation, more requirements have been proposed on the structure of deep-sea oil pipelines. The influencing factors of lateral buckling of a pipe-in-pipe (PIP) structure containing initial imperfections and its critical force were investigated in this study by conducting an experiment, a finite element analysis, and a theoretical derivation. The change laws on the influence of initial imperfections of the PIP structure during thermal loading were revealed through an experimental study by using imperfection amplitude and wavelength as parameters. Appropriate finite element models were established, and the influences of initial imperfections, pipe-soil interaction, and the height and the number of centralizers on the global buckling critical force of the PIP structure were analyzed. The formulas of global buckling critical force of inner and outer pipes and that under pipe-soil interaction was obtained by using a theoretical derivation method. A comparative verification with experimental and finite element (FE) models result was conducted, which provided a corresponding basis for steel pipeline design.

Interaction between Upheaval/Lateral and Propagation Buckling in Subsea Pipelines

2014 ◽  
Vol 553 ◽  
pp. 434-438
Author(s):  
Hassan Karampour ◽  
Faris Albermani
Keyword(s):  
Horizontal Plane ◽  
Oil And Gas ◽  
Vertical Plane ◽  
Lateral Buckling ◽  
Element Analysis ◽  
Upheaval Buckling ◽  
Oil And Gas Pipelines ◽  
Global Buckling ◽  
Internal Pressures ◽  
Subsea Pipelines

Due to high service temperatures and internal pressures in oil and gas pipelines, axial compression forces are induced in the pipe due to seabed friction. Slender trenched pipelines can experience global buckling in the vertical plane (upheaval buckling) while untrenched pipelines buckle in the horizontal plane (lateral buckling). Furthermore, deep subsea pipelines subjected to high external hydrostatics pressures can undergo catastrophic propagation buckling. In this study, the possible interaction between upheaval/lateral buckling and propagation buckling is numerically investigated using finite element analysis. A new concept is proposed for subsea pipelines design that gives higher capacity than conventional pipelines.

Behavior of NPS30 Pipe Subject to Denting Load

2014 ◽  
Author(s):  
Hossein Ghaednia ◽  
Kyle Gerard ◽  
Sudip Bhattacharjee ◽  
Sreekanta Das
Keyword(s):  
Experimental Study ◽  
Finite Element ◽  
Structural Integrity ◽  
Oil And Gas ◽  
Three Dimensional ◽  
Petroleum Products ◽  
Lateral Loads ◽  
Element Analysis ◽  
Engineering Research ◽  
Three Dimensional Finite Element

Pipeline is the common mode for transporting oil, gas, and various petroleum products. Structural integrity of oil and gas transmission pipelines is often threatened by external interferences such as concentrated lateral loads and as a result, a failure of the pipeline may occur due to “mechanical damages”. Sometime, this load may not cause immediate rupture of pipes; rather form a dent which can reduce the pressure capacity of the pipeline. A dent is a localized defect in the pipe wall in the form of a permanent inward plastic deformation. This kind of defect is a matter of serious concern for the pipeline operator since a rupture or a leak may occur. Accordingly, an extensive experimental study is currently underway at the Centre for Engineering Research in Pipelines (CERP), University of Windsor on 30 inch (762 mm) diameter and X70 grade pipes with D/t of 90. The aim of this research is to examine the influence of various parameters such as dent shape and service pressure on strain distributions of dented pipe. Also, three-dimensional finite element models were developed and validated for determining strains underneath the indenter. The load-deformation behavior of pipes subject to this type of lateral denting load obtained from experimental study and finite element analysis is discussed in this paper. In addition, distributions of important strains in and around the dent obtained from the study are also discussed.

scholarly journals A Finite Element Study on Compressive Resistance Degradation of Square and Circular Steel Braces under Axial Cyclic Loading

2021 ◽  
Vol 11 (13) ◽  
pp. 6094
Author(s):  
Hubdar Hussain ◽  
Xiangyu Gao ◽  
Anqi Shi
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Cyclic Loading ◽  
Slenderness Ratio ◽  
Hysteretic Behavior ◽  
Element Analysis ◽  
Section Shape ◽  
Axial Cyclic Loading ◽  
Global Buckling ◽  
Parametric Studies

In this study, detailed finite element analysis was conducted to examine the seismic performance of square and circular hollow steel braces under axial cyclic loading. Finite element models of braces were constructed using ABAQUS finite element analysis (FEA) software and validated with experimental results from previous papers to expand the specimen’s matrix. The influences of cross-section shape, slenderness ratio, and width/diameter-to-thickness ratio on hysteretic behavior and compressive-tensile strength degradation were studied. Simulation results of parametric studies show that both square and circular hollow braces have a better cyclic performance with smaller slenderness and width/diameter-to-thickness ratios, and their compressive-tensile resistances ratio significantly decreases from cycle to cycle after the occurrence of the global buckling of braces.

Buckling characteristics of cut-out borne composite stiffened hyperbolic paraboloid shell panel

2021 ◽  
pp. 146442072110058
Author(s):  
Sarmila Sahoo
Keyword(s):  
Finite Element ◽  
Orientation Angle ◽  
Buckling Load ◽  
Benchmark Problems ◽  
Hyperbolic Paraboloid ◽  
Element Analysis ◽  
Load Effect ◽  
Global Buckling ◽  
Fiber Orientation Angle ◽  
Shell Panel

The present study investigates buckling characteristics of cut-out borne stiffened hyperbolic paraboloid shell panel made of laminated composites using finite element analysis to evaluate the governing differential equations of global buckling of the structure. The finite element code is validated by solving benchmark problems from literature. Different parametric variations are studied to find the optimum panel buckling load. Laminations, boundary conditions, depth of stiffener and arrangement of stiffeners are found to influence the panel buckling load. Effect of different parameters like cut-out size, shell width to thickness ratio, degree of orthotropy and fiber orientation angle of the composite layers on buckling load are also studied. Parametric and comparative studies are conducted to analyze the buckling strength of composite hyperbolic paraboloid shell panel with cut-out.

Failure analysis of simple overlap bonding joints and numerical investigation of the adhered tip geometry effect on the joint strength

2021 ◽  
Vol 63 (11) ◽  
pp. 1007-1011
Author(s):  
İsmail Saraç
Keyword(s):  
Finite Element Analysis ◽  
Experimental Study ◽  
Finite Element ◽  
Reference Model ◽  
Lap Joints ◽  
Shear Stresses ◽  
Element Analysis ◽  
Single Lap Joints ◽  
Failure Loads ◽  
Previous Experimental Study

Abstract This study was carried out in two stages. In the first step, a numerical study was performed to verify the previous experimental study. In accordance with the previous experimental study data, single lap joints models were created using the ANSYS finite element analysis program. Then, nonlinear stress and failure analyses were performed by applying the failure loads obtained in the experimental study. The maximum stress theory was used to find finite element failure loads of the single lap joints models. As a result of the finite element analysis, an approximate 80 % agreement was found between experimental and numerical results. In the second step of the study, in order to increase the bond strength, different overlap end geometry models were produced and peel and shear stresses in the adhesive layer were compared according to the reference model. As a result of the analyses, significant strength increases were calculated according to the reference model. The strength increase in model 3 and model 5 was found to be 80 % and 67 %, respectively, relative to the reference model.

Flexible Flowline Walking Tendency on Seabed With Longitudinal Undulations and Transverse Gradients

2018 ◽  
Author(s):  
Graeme Roberts ◽  
T. Sriskandarajah ◽  
Gianluca Colonnelli ◽  
Arnaud Roux ◽  
Alan Roy ◽  
...  
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Temperature Gradients ◽  
Radius Of Curvature ◽  
Bend Radius ◽  
Lateral Buckling ◽  
Element Analysis ◽  
Slip Tendency ◽  
Start Ups ◽  
The Impact

A method of carrying out a combined axial walking and lateral buckling assessment for a flexible flowline has been developed using finite element analysis. The method overcomes limitations of screening assessments which could be inconclusive when applied either to a flexible flowline on an undulating seabed with transverse gradients or to one that buckles during hydrotest. Flexible flowlines that were to be surface-laid on a seabed with longitudinal undulations and transverse gradients were assessed using the method. The flexible flowlines were simulated in their as-laid state, and the simulation incorporated hydrotest pressure and the pressure & temperature gradients and transients associated with multiple start-ups. The objective was to quantify the axial walking and lateral slip tendency of the flexible flowlines and the impact that walking might have on the connected end structures. The lateral buckle locations predicted by finite element analysis were compared to a post-hydrotest survey and the radius of curvature from analysis was compared to the minimum bend radius of the flexible.

Pipeline Dent Management Program

2002 ◽  
Author(s):  
Scott D. Ironside ◽  
L. Blair Carroll
Keyword(s):  
Finite Element ◽  
Oil And Gas ◽  
Selection Process ◽  
Element Model ◽  
Field Trials ◽  
Management Program ◽  
Operating Conditions ◽  
Published Data ◽  
Element Analysis ◽  
The Past

Enbridge Pipelines Inc. operates the world’s longest and most complex liquids pipeline network. As part of Enbridge’s Integrity Management Program In-Line Inspections have been and will continue to be conducted on more than 15,000 km of pipeline. The Inspection Programs have included using the most technologically advanced geometry tools in the world to detect geometrical discontinuities such as ovality, dents, and buckles. During the past number of years, Enbridge Pipelines Inc. has been involved in developing a method of evaluating the suitability of dents in pipelines for continued service. The majority of the work involved the development of a method of modeling the stresses within a dent using Finite Element Analysis (FEA). The development and validation of this model was completed by Fleet Technology Limited (FTL) through several projects sponsored by Enbridge, which included field trials and comparisons to previously published data. This model combined with proven fracture mechanics theory provides a method of determining a predicted life of a dent based on either the past or future operating conditions of the pipeline. CSA Standard Z662 – Oil and Gas Pipeline Systems provides criteria for the acceptability of dents for continued service. There have been occurrences, however, where dents that meet the CSA acceptability criteria have experienced failure. The dent model is being used to help define shape characteristics in addition to dent depth, the only shape factor considered by CSA, which contribute to dent failure. The dent model has also been utilized to validate the accuracy of current In-Line Inspection techniques. Typically a dent will lose some of its shape as the overburden is lifted from the pipeline and after the indentor is removed. Often there can be a dramatic “re-rounding” that will occur. The work included comparing the re-rounded dent shapes from a Finite Element model simulating the removal of the constraint on the pipe to the measured dent profile from a mold of the dent taken in the field after it has been excavated. This provided a measure of the accuracy of the tool. This paper will provide an overview of Enbridge’s dent management program, a description of the dent selection process for the excavation program, and a detailed review of the ILI validation work.

Clamp Load Decay Due to Material Creep of Lightweight-Material Joints Under Cyclic Temperature

2015 ◽  
Vol 137 (5) ◽  
Author(s):  
Sayed A. Nassar ◽  
Amir Kazemi
Keyword(s):  
Finite Element ◽  
Temperature Profile ◽  
Thermal Loading ◽  
Substrate Material ◽  
Valuable Insight ◽  
Substrate Thickness ◽  
Element Analysis ◽  
Fea Model ◽  
Cyclic Temperature ◽  
Material Creep

Experimental and finite element techniques are used for investigating the effect of cyclic thermal loading on the clamp load decay in preloaded single-lap bolted joints that are made of multimaterial lightweight alloys. Substrate material combinations include aluminum, magnesium, and steel, with various coupon thicknesses. The range of cyclic temperature profile varies between −20 °C and +150 °C in a computer-controlled environmental chamber for generating the desired cyclic temperature profile and durations. Real time clamp load data are recorded using strain gage-based, high-temperature, load cells. Clamp load decay is investigated for various combinations of joint materials, initial preload level, and substrate thickness. Thermal and material creep finite element analysis (FEA) is performed using temperature-dependent mechanical properties. The FEA model and results provided a valuable insight into the experimental results regarding the vulnerability of some lightweight materials to significant material creep at higher temperatures.

Finite Element Analysis of Casing Material Behavior in Steam Injection Well Operations

2015 ◽  
Vol 799-800 ◽  
pp. 196-200
Author(s):  
Abhilash M. Bharadwaj ◽  
Sonny Irawan ◽  
Saravanan Karuppanan ◽  
Mohamad Zaki bin Abdullah ◽  
Ismail bin Mohd Saaid
Keyword(s):  
Finite Element ◽  
Oil Recovery ◽  
Thermal Stresses ◽  
Oil And Gas ◽  
Extreme Temperature ◽  
Injection Pressure ◽  
Oil And Gas Industry ◽  
Steam Injection ◽  
Material Behavior ◽  
Element Analysis

Casing design is one of the most important parts of the well planning in the oil and gas industry. Various factors affecting the casing material needs to be considered by the drilling engineers. Wells partaking in thermal oil recovery processes undergo extreme temperature variation and this induces high thermal stresses in the casings. Therefore, forecasting the material behavior and checking for failure mechanisms becomes highly important. This paper uses Finite Element Methods to analyze the behavior two of the frequently used materials for casing - J55 and L80 steels. Modeling the casing and application of boundary conditions are performed through Ansys Workbench. Effect of steam injection pressure and temperature on the materials is presented in this work, indicating the possibilities of failure during heating cycle. The change in diameter of the casing body due to axial restriction is also presented. This paper aims to draw special attention towards the casing design in high temperature conditions of the well.

Sign in / Sign up

Export Citation Format

Share Document