scholarly journals X-ray and Neutron Study on the Structure of Hydrous SiO2 Glass up to 10 GPa

Minerals ◽  
2020 ◽  
Vol 10 (1) ◽  
pp. 84 ◽  
Author(s):  
Satoru Urakawa ◽  
Toru Inoue ◽  
Takanori Hattori ◽  
Asami Sano-Furukawa ◽  
Shinji Kohara ◽  
...  
Keyword(s):  
Oxide Glasses ◽  
Void Space ◽  
X Ray Diffraction ◽  
Amorphous Sio2 ◽  
Sio2 Glass ◽  
X Ray ◽  
X Ray Scattering ◽  
Medium Range ◽  
Two Phases ◽  
A Minor

The structure of hydrous amorphous SiO2 is fundamental in order to investigate the effects of water on the physicochemical properties of oxide glasses and magma. The hydrous SiO2 glass with 13 wt.% D2O was synthesized under high-pressure and high-temperature conditions and its structure was investigated by small angle X-ray scattering, X-ray diffraction, and neutron diffraction experiments at pressures of up to 10 GPa and room temperature. This hydrous glass is separated into two phases: a major phase rich in SiO2 and a minor phase rich in D2O molecules distributed as small domains with dimensions of less than 100 Å. Medium-range order of the hydrous glass shrinks compared to the anhydrous SiO2 glass by disruption of SiO4 linkage due to the formation of Si–OD deuterioxyl, while the response of its structure to pressure is almost the same as that of the anhydrous SiO2 glass. Most of D2O molecules are in the small domains and hardly penetrate into the void space in the ring consisting of SiO4 tetrahedra.

Phase separation in gel-derived materials, separation and crystallization of SnO2 within an amorphous SiO2 matrix

1992 ◽  
Vol 7 (2) ◽  
pp. 435-443 ◽  
Author(s):  
R. Dal Maschio ◽  
S. Dirè ◽  
G. Carturan ◽  
S. Enzo ◽  
L. Battezzati
Keyword(s):  
Surface Segregation ◽  
Primary Crystallization ◽  
Amorphous Sio2 ◽  
X Ray ◽  
X Ray Scattering ◽  
Transmission Electron ◽  
Different Temperatures ◽  
Two Phases ◽  
Average Size ◽  
Ray Scattering

On heating a gel of composition 33.5SnO2−66.5SiO2 (wt. %) up to 1050 °C, SnO2 crystallization occurred with different mechanisms according to thermal treatments. Thermal analysis, SAXS (Small Angle X-Ray Scattering), WAXS (Wide Angle X-Ray Scattering), and TEM (Transmission Electron Microscopy) results obtained for samples treated at different temperatures demonstrated that the SnO2 load is divided into two moieties, one composed of isolated SnO2 particles suitable for primary crystallization yielding crystallites with 4.0 nm of average size; the other, being dissolved in SiO2, remains in the amorphous SiO2/SnO2 solid solution up to the highest temperature. The presence of these two phases accounts for SnO2 surface segregation at the expense of the SnO2 concentration of neighboring outer layers and the independence of apparent density on temperature.

scholarly journals Structure of a monolayer of molecular rotors on aqueous subphase from grazing-incidence X-ray diffraction

2018 ◽  
Vol 115 (38) ◽  
pp. 9373-9378 ◽  
Author(s):  
Jiří Kaleta ◽  
Jin Wen ◽  
Thomas F. Magnera ◽  
Paul I. Dron ◽  
Chenhui Zhu ◽  
...  
Keyword(s):  
Grazing Incidence ◽  
Molecular Rotors ◽  
Triangular Grid ◽  
X Ray Diffraction ◽  
X Ray ◽  
Aqueous Subphase ◽  
Preparation Conditions ◽  
X Ray Scattering ◽  
A Minor

In situ grazing-incidence X-ray scattering shows that a monolayer of artificial rod-shaped dipolar molecular rotors produced on the surface of an aqueous subphase in a Langmuir trough has a structure conducive to a 2D ferroelectric phase. The axes of the rotors stand an average of 0.83 nm apart in a triangular grid, perpendicular to the surface within experimental error. They carry 2,3-dichlorophenylene rotators near rod centers, between two decks of interlocked triptycenes installed axially on the rotor axle. The analysis is based first on simultaneous fitting of observed Bragg rods and second on fitting the reflectivity curve with only three adjustable parameters and the calculated rotor electron density, which also revealed the presence of about seven molecules of water near each rotator. Dependent on preparation conditions, a minor and variable amount of a different crystal phase may also be present in the monolayer.

Defect structures of Nb1+αS2 sulfidation scales

1992 ◽  
Vol 50 (1) ◽  
pp. 38-39
Author(s):  
Chuxin Zhou ◽  
L. W. Hobbs
Keyword(s):  
Stacking Faults ◽  
Rhombohedral Structure ◽  
Stacking Sequence ◽  
Defect Structures ◽  
X Ray Diffraction ◽  
X Ray ◽  
Plane Normal ◽  
Lower Case ◽  
Sulfur Layer ◽  
Two Phases

One of the major purposes in the present work is to study the high temperature sulfidation properties of Nb in severe sulfidizing environments. Kinetically, the sulfidation rate of Nb is satisfactorily slow, but the microstructures and non-stoichiometry of Nb1+αS2 challenge conventional oxidation/sulfidation theory and defect models of non-stoichiometric compounds. This challenge reflects our limited knowledge of the dependence of kinetics and atomic migration processes in solid state materials on their defect structures.Figure 1 shows a high resolution image of a platelet from the middle portion of the Nb1+αS2 scale. A thin lamellar heterogeneity (about 5nm) is observed. From X-ray diffraction results, we have shown that Nb1+αS2 scale is principally rhombohedral structure, but 2H-NbS2 can result locally due to stacking faults, because the only difference between these 2H and 3R phases is variation in the stacking sequence along the c axis. Following an ABC notation, we use capital letters A, B and C to represent the sulfur layer, and lower case letters a, b and c to refer to Nb layers. For example, the stacking sequence of 2H phase is AbACbCA, which is a ∼12Å period along the c axis; the stacking sequence of 3R phase is AbABcBCaCA to form an ∼18Å period along the c axis. Intergrowth of these two phases can take place at stacking faults or by a shear in the basal plane normal to the c axis.

New Structure of CTAB Templated Silica Films as revealed by GISAXS coupled to HRTEM

2000 ◽  
Vol 628 ◽  
Author(s):  
Sophie Besson ◽  
Catherine Jacquiod ◽  
Thierry Gacoin ◽  
André Naudon ◽  
Christian Ricolleau ◽  
...  
Keyword(s):  
Cetyltrimethylammonium Bromide ◽  
Grazing Incidence ◽  
Hexagonal Structure ◽  
X Ray Diffraction ◽  
Electronic Microscopy ◽  
Silica Films ◽  
X Ray ◽  
X Ray Scattering ◽  
Hexagonal Arrangement ◽  
Spherical Micelles

ABSTRACTA microstructural study on surfactant templated silica films is performed by coupling traditional X-Ray Diffraction (XRD) and Transmission Electronic Microscopy (TEM) to Grazing Incidence Small Angle X-Ray Scattering (GISAXS). By this method it is shown that spin-coating of silicate solutions with cationic surfactant cetyltrimethylammonium bromide (CTAB) as a templating agent provides 3D hexagonal structure (space group P63/mmc) that is no longer compatible with the often described hexagonal arrangement of tubular micelles but rather with an hexagonal arrangement of spherical micelles. The extent of the hexagonal ordering and the texture can be optimized in films by varying the composition of the solution.

Comparative Studies of Ultra Low-κ Porous Silica Films with 2-D Hexagonal and Disordered Pore Structures

2004 ◽  
Vol 812 ◽  
Author(s):  
Nobutoshi Fujii ◽  
Kazuhiro Yamada ◽  
Yoshiaki Oku ◽  
Nobuhiro Hata ◽  
Yutaka Seino ◽  
...  
Keyword(s):  
Pore Structure ◽  
Nonionic Surfactants ◽  
Porous Silica ◽  
Silica Film ◽  
X Ray Diffraction ◽  
Silica Films ◽  
X Ray ◽  
X Ray Scattering ◽  
Porous Silica Film ◽  
Diffraction Peaks

AbstractPeriodic 2-dimensional (2-D) hexagonal and the disordered pore structure silica films have been developed using nonionic surfactants as the templates. The pore structure was controlled by the static electrical interaction between the micelle of the surfactant and the silica oligomer. No X-ray diffraction peaks were observed for the disordered mesoporous silica films, while the pore diameters of 2.0-4.0 nm could be measured by small angle X-ray scattering spectroscopy. By comparing the properties of the 2-D hexagonal and the disordered porous silica films which have the same porosity, it is found that the disordered porous silica film has advantages in terms of the dielectric constant and Young's modulus as well as the hardness. The disordered porous silica film is more suitable for the interlayer dielectrics for ULSI.

Time-resolved isothermal crystallization of absorbable PGA-co-PLA copolymer by synchrotron small-angle X-ray scattering and wide-angle X-ray diffraction

Polymer ◽  
2001 ◽  
Vol 42 (21) ◽  
pp. 8965-8973 ◽  
Author(s):  
Zhi-Gang Wang ◽  
Xuehui Wang ◽  
Benjamin S. Hsiao ◽  
Saša Andjelić ◽  
Dennis Jamiolkowski ◽  
...  
Keyword(s):  
Small Angle ◽  
Isothermal Crystallization ◽  
Wide Angle ◽  
X Ray Diffraction ◽  
Time Resolved ◽  
X Ray ◽  
X Ray Scattering ◽  
Ray Scattering

Medium-Range Order of Amorphous Silicon Germanium Alloys: Small-Angle X-Ray Scattering Study

1989 ◽  
Vol 28 (Part 2, No. 7) ◽  
pp. L1092-L1095 ◽  
Author(s):  
Shin-ichi Muramatsu ◽  
Toshikazu Shimada ◽  
Hiroshi Kajiyama ◽  
Kazufumi Azuma ◽  
Takeshi Watanabe ◽  
...  
Keyword(s):  
Amorphous Silicon ◽  
Small Angle ◽  
Silicon Germanium ◽  
Range Order ◽  
Medium Range Order ◽  
X Ray ◽  
X Ray Scattering ◽  
Medium Range ◽  
Scattering Study ◽  
Amorphous Silicon Germanium

An X-ray scattering study on inverted Ge–Si huts grown at low temperatures

2004 ◽  
Vol 19 (4) ◽  
pp. 347-351
Author(s):  
J. Xu ◽  
X. S. Wu ◽  
B. Qian ◽  
J. F. Feng ◽  
S. S. Jiang ◽  
...  
Keyword(s):  
Low Temperatures ◽  
Lattice Strain ◽  
Lattice Mismatch ◽  
Grazing Incidence ◽  
X Ray Diffraction ◽  
X Ray ◽  
X Ray Scattering ◽  
Transmission Electron ◽  
Large Lattice ◽  
Scattering Study

Ge–Si inverted huts, which formed at the Si∕Ge interface of Si∕Ge superlattice grown at low temperatures, have been measured by X-ray diffraction, grazing incidence X-ray specular and off-specular reflectivities, and transmission electron microscopy (TEM). The surface of the Si∕Ge superlattice is smooth, and there are no Ge–Si huts appearing on the surface. The roughness of the surfaces is less than 3 Å. Large lattice strain induced by lattice mismatch between Si and Ge is found to be relaxed because of the intermixing of Ge and Si at the Si∕Ge interface.

A high-throughput assembly of beam-shaping channel-cut monochromators for laboratory high-resolution X-ray diffraction and small-angle X-ray scattering experiments

2021 ◽  
Vol 54 (3) ◽  
Author(s):  
Peter Nadazdy ◽  
Jakub Hagara ◽  
Petr Mikulik ◽  
Zdenko Zaprazny ◽  
Dusan Korytar ◽  
...  
Keyword(s):  
High Resolution ◽  
Small Angle ◽  
Photon Flux ◽  
Photon Flux Density ◽  
X Ray Diffraction ◽  
High Beam ◽  
X Ray ◽  
X Ray Scattering ◽  
Beam Collimation ◽  
Ray Scattering

A four-bounce monochromator assembly composed of Ge(111) and Ge(220) monolithic channel-cut monochromators with V-shaped channels in a quasi-dispersive configuration is presented. The assembly provides an optimal design in terms of the highest transmittance and photon flux density per detector pixel while maintaining high beam collimation. A monochromator assembly optimized for the highest recorded intensity per detector pixel of a linear detector placed 2.5 m behind the assembly was realized and tested by high-resolution X-ray diffraction and small-angle X-ray scattering measurements using a microfocus X-ray source. Conventional symmetric and asymmetric Ge(220) Bartels monochromators were similarly tested and the results were compared. The new assembly provides a transmittance that is an order of magnitude higher and 2.5 times higher than those provided by the symmetric and asymmetric Bartels monochromators, respectively, while the output beam divergence is twice that of the asymmetric Bartels monochromator. These results demonstrate the advantage of the proposed monochromator assembly in cases where the resolution can be partially sacrificed in favour of higher transmittance while still maintaining high beam collimation. Weakly scattering samples such as nanostructures are an example. A general advantage of the new monochromator is a significant reduction in the exposure time required to collect usable experimental data. A comparison of the theoretical and experimental results also reveals the current limitations of the technology of polishing hard-to-reach surfaces in X-ray crystal optics.

Sign in / Sign up

Export Citation Format

Share Document