scholarly journals Distribution of Lanthanides, Yttrium, and Scandium in the Pilot-Scale Beneficiation of Fly Ashes Derived from Eastern Kentucky Coals

Minerals ◽  
2020 ◽  
Vol 10 (2) ◽  
pp. 105 ◽  
Author(s):  
James C. Hower ◽  
John G. Groppo ◽  
Prakash Joshi ◽  
Dorin V. Preda ◽  
David P. Gamliel ◽  
...  
Keyword(s):  
Rare Earth ◽  
Fly Ash ◽  
Power Plants ◽  
Pilot Scale ◽  
Fly Ashes ◽  
Eastern Kentucky ◽  
Minor Elements ◽  
High Concentrations ◽  
The Individual ◽  
Plant Basis

In this study, Central Appalachian coal-derived fly ashes from two power plants were beneficiated in a pilot-scale facility in order to produce a product with a relatively consistent concentration of rare earth elements (REE). The <200-mesh final fly ash product was produced by removing the carbon- and Fe-rich particles prior to screening at 200 mesh (75 µm). The Plant D fly ash had high concentrations of CaO and SO3, which were diminished through the two months when the ash was being beneficiated, representing a consequence of the heat, humidity, and excessive rainfall in the Kentucky summer. The high CaO and SO3 concentrations through the early runs likely contributed to the lower REE in the <200-mesh products of those runs. Of the non-REE minor elements, Ba, V, Mn, Zn, and As showed the greatest between-run variations within the runs for each plant. The overall REE concentrations proved to be similar, both on a between-run basis for the individual fly ash sources and on a between-plant basis. Variations in fly ash quality will occur in larger-scale operations, so on-going attention to the fly ash quality and the response of the fly ash to beneficiation is necessary. Changes in the Plant D fly ash with time imply that both the freshness of the original ash and the length and conditions of its storage at the site of beneficiation could be factors in the quality and consistency of the processed fly ash.

Distribution of rare earth elements in the pilot-scale processing of fly ashes derived from eastern Kentucky coals: Comparisons of the feed and processed ashes

Fuel ◽  
2021 ◽  
Vol 295 ◽  
pp. 120562
Author(s):  
James C. Hower ◽  
John G. Groppo ◽  
Robert B. Jewell ◽  
John D. Wiseman ◽  
Tristana Y. Duvallet ◽  
...  
Keyword(s):  
Rare Earth ◽  
Rare Earth Elements ◽  
Pilot Scale ◽  
Fly Ashes ◽  
Eastern Kentucky

Quantitative X-Ray Fluorescence Analysis for Fly Ash Samples

1983 ◽  
Vol 27 ◽  
pp. 497-504
Author(s):  
Scott Schlorholtz ◽  
Mustafa Boybay
Keyword(s):  
Fly Ash ◽  
Sample Preparation ◽  
Power Plants ◽  
Fluorescence Analysis ◽  
Complex Problem ◽  
Point Of View ◽  
Fly Ashes ◽  
X Ray ◽  
Minor Elements ◽  
Minimal Sample

The disposal of fly ash from coal burning power plants is rapidly becoming an environmentally complex problem. Recently though, the attitude towards fly ash use has been changing from a disposal oriented point of view to a more rational position which considers fly ash as a resource to be recycled. One major hinderance of fly ash use has been the extreme variability of composition that exists between fly ashes produced at different power plants. This variability makes the analysis of fly ash very important.The most common methods currently used for fly ash analysis are atomic absorption or wet chemistry methods defined in ASTM C311. Both methods tend to be expensive, time consuming, and sample preparation is both tedious and critical for some elements. In this study X-ray fluorescence (QXRF) is used for the quantitative analysis of the major and minor elements found in “typical” fly ashes. The method, which is computer controlled, is quick, reliable, and requires minimal sample preparation.

scholarly journals Nano-Scale Rare Earth Distribution in Fly Ash Derived from the Combustion of the Fire Clay Coal, Kentucky

Minerals ◽  
2019 ◽  
Vol 9 (4) ◽  
pp. 206 ◽  
Author(s):  
James Hower ◽  
Dali Qian ◽  
Nicolas Briot ◽  
Eduardo Santillan-Jimenez ◽  
Madison Hood ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Rare Earth ◽  
Fly Ash ◽  
Electron Diffraction ◽  
Eastern Kentucky ◽  
Nano Scale ◽  
Selected Area Electron Diffraction ◽  
Transmission Electron ◽  
Diffraction Patterns ◽  
Fire Clay

Fly ash from the combustion of eastern Kentucky Fire Clay coal in a southeastern United States pulverized-coal power plant was studied by scanning electron microscopy (SEM), transmission electron microscopy (TEM), and selected area electron diffraction (SAED). TEM combined with elemental analysis via energy dispersive X-ray spectroscopy (EDS) showed that rare earth elements (REE; specifically, La, Ce, Nd, Pr, and Sm) were distributed within glassy particles. In certain cases, the REE were accompanied by phosphorous, suggesting a monazite or similar mineral form. However, the electron diffraction patterns of apparent phosphate minerals were not definitive, and P-lean regions of the glass consisted of amorphous phases. Therefore, the distribution of the REE in the fly ash seemed to be in the form of TEM-visible nano-scale crystalline minerals, with additional distributions corresponding to overlapping ultra-fine minerals and even true atomic dispersion within the fly ash glass.

scholarly journals DETERMINING THE ROLE OF INDIVIDUAL FLY ASH PARTICLES IN INFLUENCING THE VARIATION IN THE OVERALL PHYSICAL, MORPHOLOGICAL, AND CHEMICAL PROPERTIES OF FLY ASH

2016 ◽  
Vol 56 (4) ◽  
pp. 265-282 ◽  
Author(s):  
Usman Haider ◽  
Zdenek Bittnar ◽  
Lubomír Kopecky ◽  
Vít Šmilauer ◽  
Jaroslav Pokorny ◽  
...  
Keyword(s):  
Fly Ash ◽  
Power Plants ◽  
Thermal Power ◽  
Chemical Properties ◽  
Cementitious Materials ◽  
Individual Particle ◽  
Particle Analysis ◽  
Fly Ashes ◽  
Alumino Silicate ◽  
Individual Particles

The properties of fly ashes vary because of the differences in the properties of their individual particles, and the determination of variation in these properties is of interest to the industries which use pulverized raw fly ash in applications, such as in cementitious materials and in the recovery of certain rare elements from raw fly ash. To investigate the differences in individual particles, four pulverized raw fly ashes from thermal power plants of the Czech Republic were used in this research. It was observed from FE-SEM that all four fly ashes consist of glassy hollow spherical, solid spherical, porous spherical, bright spherical, porous slaggy and compact slaggy particles. Box and whisker diagrams were plotted from the data of EDX individual particle analyses, which showed that the data of percentages for the Si, Al, and Fe elements is more scattered as compared to other elements. It was further observed from ternary phase diagrams and pseudo coloured images, that nature of fly ash particles changes from alumino silicate glassy to alumino silicate calcite metallic to pure ferro-metallic,where glassy particles showed high percentages and pure calcite particles were absent in fly ashes. Furthermore, a comparison between the XRF, the EDX total area analyses, showed that the EDX individual particle analysis gives more realistic and reliable data with median, mean, and the standard deviation for percentages of each element present in the fly ashes.

Transmitted and Reflected Visible Light Microscopy of Two Bituminous Fly Ashes

1984 ◽  
Vol 43 ◽  
Author(s):  
Donald L. Biggs ◽  
Joseph J. Bruns
Keyword(s):  
Fly Ash ◽  
Light Microscopy ◽  
Silicate Glass ◽  
Power Plants ◽  
Magnetic Fraction ◽  
Fly Ashes ◽  
Complete Replacement ◽  
Replacement Product ◽  
Nonmagnetic Particles ◽  
Ferrite Spinel

AbstractFly ashes of high magnetic content taken from two midwestern power plants were examined to determine the mineralogy of the magnetic and nonmagnetic fractions. Fly ash spheres from the magnetic fraction are predominantly composed of ferrite spinel, hematite and silicate glass. The hematite appears to be a replacement product of the original ferrite spinel. Nonmagnetic phases include mullite, lime, small amounts of hematite and silicate glass. Quartz morphology indicates that it did not fuse in the furnace. Mullite and lime have morphologies indicative of crystallization in the furnace. Hematite is bonded to the nonmagnetic particles or as a complete replacement of ferrite spinel spheres.

The Suitability of Fly Ash for Use in Concrete According to EN 450 Based on their Particle Size

2018 ◽  
Vol 276 ◽  
pp. 110-115
Author(s):  
Martin Ťažký ◽  
Martin Labaj ◽  
Rudolf Hela
Keyword(s):  
Fly Ash ◽  
Power Plants ◽  
Catalytic Reduction ◽  
Raw Materials ◽  
Thermal Power ◽  
Combustion Process ◽  
Thermal Power Plants ◽  
Mechanical Parameters ◽  
Fly Ashes ◽  
The Impact

The by-products of energy industry are nowadays often affected by new limits governing the production of harmful gases discharged into the air. These stricter and stricter criteria are often met by electricity producers by changing the combustion process in thermal power plants itself. Nowadays, the SNCR (selective non-catalytic reduction) application is quite common in the combustion process in order to help reduce the nitrogen oxide emission. This article deals with the primary measures of thermal power plants, which in particular consist of a modified treatment of raw materials (coal) entering the combustion process. These primary measures then often cause the formation of fly ash with unsuitable fineness for the use in concrete according to EN 450. The paper presents the comparison of the physico-mechanical parameters of several fly ashes with a different fineness values. The primary task is to assess the impact of non-suitable granulometry in terms of EN 450 on the other physico-mechanical parameters of fly ashes sampled within the same thermal power plant. Several fly ashes produced in the Czech Republic and surrounding countries were evaluated in this way.

scholarly journals Synthesis and sintering of high-temperature composites based on mechanically activated fly ash

2012 ◽  
Vol 44 (2) ◽  
pp. 135-146 ◽  
Author(s):  
A. Terzic ◽  
Lj. Pavlovic ◽  
N. Obradovic ◽  
V. Pavlovic ◽  
J. Stojanovic ◽  
...  
Keyword(s):  
Thermal Stability ◽  
High Temperature ◽  
Fly Ash ◽  
Mechanical Activation ◽  
Power Plants ◽  
Sem Analysis ◽  
Fly Ashes ◽  
Physico Chemical ◽  
Fly Ash Utilization ◽  
And Behavior

Amount of fly ash which is and yet to be generated in the coming years highlights the necessity of developing new methods of the recycling where this waste can be reused in significant quantity. A new possibility for fly ash utilization is in high-temperature application (thermal insulators or/and refractory material products). As such, fly ash has to adequately answer the mechanical and thermal stability criteria. One of the ways of achieving it is by applying mechanical activation procedure on fly ash. In present study, fly ashes from two different power plants were mechanically activated in a planetary ball mill. Mechanically treated fly ashes were cemented with two different binders: standard Portland cement and high-aluminates cement. Physico-chemical analysis and investigation of mineralogical components of composites are emphasized, due to the changes occurred in fly ash during mechanical activation and sintering of composites. Macro-performance of the composites was correlated to the microstructure of fly ash studied by means of XRD and SEM analysis. Thermal stability of crystalline phases was investigated with DTA. Highlight was placed on determination of relationship between mechanically activated fly ash and obtained composites microstructure on one side and behavior of sintered composites on the other side.

scholarly journals Separation of Cenospheres from Fly Ashes by Floatation Method

2010 ◽  
Vol 13 (1-2) ◽  
pp. 89 ◽  
Author(s):  
L.M. Manоcha ◽  
K.A. Ram ◽  
S.M. Manocha
Keyword(s):  
Fly Ash ◽  
Power Plants ◽  
Thermal Power ◽  
Ceramic Particle ◽  
Composition Analysis ◽  
High Concentration ◽  
Fly Ashes ◽  
Power Station ◽  
Different Types ◽  
Chemical Composition Analysis

Fly-ashes are non-combustible mineral residues which are produced from coal in thermal power plants. Four different types of fly ashes were collected from different power station in Gujarat. Characterization through SEM shows that fly ash contains cenosphere i.e. gas bubble containing ceramic particle independent of their bulk density. Floatation technique was used for the separation of cenosphere from fly ash. Two solvents with extremely different densities were used for the separation of cenospheres. All methods gave approximately yield of less than 1 % cenosphere in fly ash. Color of cenospheres varied from gray to almost white and the value of density range from 0.4 – 0.8 g/cc. Further, chemical composition analysis revealed that cenospheres do not contain any high concentration of hazardous elements.

scholarly journals Stabilization of Indian Fly Ashes with Soils, Cement, and Randomly Oriented Fibers

2012 ◽  
Vol 3 ◽  
pp. 1-8
Author(s):  
Shenbaga R. Kaniraj ◽  
V. Gayathri ◽  
V.G. Havanagi
Keyword(s):  
Fly Ash ◽  
Power Plants ◽  
Thermal Power ◽  
Experimental Studies ◽  
Fly Ashes ◽  
Strength Criteria ◽  
Permeability Characteristics ◽  
Polyester Fibers ◽  
Soil Mixtures ◽  
Pavement Base

 Experimental studies were carried out on fly ashes from two Indian thermal power plants, namely Rajghat and Dadri, with the aim of improving the utilization of fly ash in geotechnical engineering applications. It was attempted to improve the engineering performance of fly ash by several means such as by mixing fly ash with soils, cement, and polyester fibers. The research program included the study of: a) physical properties, chemical composition and morphology of the fly ashes; b) compaction, strength, and permeability characteristics of the fly ashes and fly ash-soil mixtures; c) compaction and strength characteristics of fly ash-soil mixtures stabilized with fibers alone, with cement alone, and with both cement and fibers. Results showed that addition of fly ash to soils would result in lighter and stronger fills. Fiber inclusions increased the strength of fly ash-soil specimens significantly and altered their behaviour from brittle to ductile. Even small cement contents increased the strength of the fly ash-soil mixtures significantly. With higher cement contents of up to 18% it was possible to prepare fly ash-cement design mixes that satisfied the strength criteria for pavement base courses.

Sign in / Sign up

Export Citation Format

Share Document