scholarly journals Calcium Phosphate-Coated Lipid Nanoparticles as a Potential Tool in Bone Diseases Therapy

Nanomaterials ◽  
2021 ◽  
Vol 11 (11) ◽  
pp. 2983
Author(s):  
Simona Sapino ◽  
Giulia Chindamo ◽  
Daniela Chirio ◽  
Maela Manzoli ◽  
Elena Peira ◽  
...  
Keyword(s):  
Calcium Phosphate ◽  
Chemical Characterization ◽  
Bone Cancer ◽  
Lipid Nanoparticles ◽  
Bone Diseases ◽  
Cell Accumulation ◽  
Human Osteosarcoma Cells ◽  
Coating Method ◽  
Uptake Studies

The treatment of bone diseases (including osteoporosis, osteoarthritis, and bone cancer) often results in reduced efficiency and/or adverse reactions due to the fact that it is not specifically targeted to the site of action. The employment of a suitable carrier should increase drug location to the site of bone disease. The purpose of this study is to prepare and characterize lipid nanoparticles (NPs) coated with calcium phosphate (CaP-NPs). A coating method, to date used only to obtain liposomes covered with CaP, is herein partially-modified to prepare CaP-coated lipid NPs. An extensive physico-chemical characterization was achieved by employing several techniques (DLS, SEM and TEM, and both combined with EDS, XRD, and FTIR) that confirmed the feasibility of the developed coating method. Preliminary uptake studies on human osteosarcoma cells (U-2OS) were performed by entrapping, as a lipid probe, Sudan Red III in NPs. The obtained data provided evidence that CaP-NPs showed higher cell accumulation than uncoated NPs. This result may have important implications for the development of drug loaded CaP-NPs to be tested in vitro with a view of planning future treatment of bone diseases, and indicate that CaP-NPs are potential vehicles for selective drug delivery to bone tissue.

scholarly journals Polydatin Induces Differentiation and Radiation Sensitivity in Human Osteosarcoma Cells and Parallel Secretion through Lipid Metabolite Secretion

2021 ◽  
Vol 2021 ◽  
pp. 1-11
Author(s):  
Amalia Luce ◽  
Stefania Lama ◽  
Pilar Chacon Millan ◽  
Annalisa Itro ◽  
Angelo Sangiovanni ◽  
...  
Keyword(s):  
Osteogenic Differentiation ◽  
Bone Cancer ◽  
Clonogenic Survival ◽  
Radiation Sensitivity ◽  
Bone Alkaline Phosphatase ◽  
Osteosarcoma Cells ◽  
Cycle Arrest ◽  
Anticancer Effects ◽  
Human Osteosarcoma Cells

Osteosarcoma is a bone cancer characterized by the production of osteoid tissue and immature bone from mesenchymal cells. Osteosarcoma mainly affects long bones (femur is most frequently site) and occur in children and young adults with greater incidence. Here, we investigated the role accomplished by polydatin, a natural antioxidative compound, in promoting osteogenic differentiation alone or after radiation therapy on osteosarcoma cells. In vitro, polydatin significantly induced cell cycle arrest in S-phase and enhanced bone alkaline phosphatase activity. Moreover, the differentiation process was paralleled by the activation of Wnt-β-catenin pathway. In combination with radiotherapy, the pretreatment with polydatin promoted a radiosensitizing effect on osteosarcoma cancer cells as demonstrated by the upregulation of osteogenic markers and reduced clonogenic survival of tumor cells. Additionally, we analyzed, by mass spectrometry, the secretion of sphingolipid, ceramides, and their metabolites in osteosarcoma cells treated with polydatin. Overall, our results demonstrate that polydatin, through the secretion of sphingolipids and ceramide, induced osteogenic differentiation, alone and in the presence of ionizing therapy. Future investigations are needed to validate the use of polydatin in clinical practice as a potentiating agent of radiotherapy-induced anticancer effects.

scholarly journals 3D Printed Calcium Phosphate Cement (CPC) Scaffolds for Anti-Cancer Drug Delivery

Pharmaceutics ◽  
2020 ◽  
Vol 12 (11) ◽  
pp. 1077
Author(s):  
Yan Wu ◽  
Lisa Woodbine ◽  
Antony M. Carr ◽  
Amit R. Pillai ◽  
Ali Nokhodchi ◽  
...  
Keyword(s):  
Drug Delivery ◽  
Calcium Phosphate ◽  
Bone Graft ◽  
Bone Cancer ◽  
Cancer Drug ◽  
Anti Cancer ◽  
3D Printed ◽  
Polymeric Solutions ◽  
Cancer Drug Delivery

One of the main applications of bone graft materials is filling the gap after the surgical removal of bone cancer or tumors. Insufficient healing commonly leads to non-union fracture which could lead to cancer resurgence or infection. Emerging 3D printing of on-demand bone graft biomaterials can deliver personalized solutions with minimized risk of relapse and recurrence of cancer after bone removal surgery. This research aims to explore 3D printed calcium phosphate cement (CPC) based scaffolds as novel anti-cancer drug delivery systems to treat bone cancer. For the study, various 3D printed CPC based scaffolds (diameter 5 mm) with interconnected pores were utilized. Various optimized polymeric solutions containing a model anticancer drug 5-fluorouracil (5-FU) was used to homogenously coat the CPC scaffolds. Both hydrophilic Soluplus (SOL) and polyethylene glycol (PEG) and a combination of both were used to develop stable coating solutions. The surface morphology of the coated scaffolds, observed via SEM, revealed deposition of the polymeric solution represented by a semi-smooth surface as opposed to the blank scaffolds that showed a smoother surface. An advanced surface analysis conducted via confocal microscopy showed a homogenous distribution of the drug throughout the coated scaffolds. Solid-state analysis studied by applying differential scanning calorimetry (DSC) and X-ray diffraction (XRD) revealed semi-crystalline nature of the drug whereas mechanical analysis conducted via texture analysis showed no evidence in the change of the mechanical properties of the scaffolds after polymeric solutions were applied. The FTIR analysis revealed no major intermolecular interactions between 5-FU and the polymers used for coatings except for F2 where a potential nominal interaction was evidenced corresponding to higher Soluplus content in the formulation. In vitro dissolution studies showed that almost 100% of the drug released within 2 h for all scaffolds. Moreover, in vitro cell culture using two different cell lines (Hek293T-human kidney immortalized cell line and HeLa-human bone osteosarcoma epithelial cell line) showed significant inhibition of cell growth as a function of decreased numbers of cells after 5 days. It can be claimed that the developed 5-FU coated 3D printed scaffolds can successfully be used as bone graft materials to potentially treat bone cancer or bone neoplasm and for personalized medical solutions in the form of scaffolds for regenerative medicine or tissue engineering applications.

scholarly journals Preparation, Physical-Chemical Characterization, and Cytocompatibility of Polymeric Calcium Phosphate Cements

2011 ◽  
Vol 2011 ◽  
pp. 1-13 ◽  
Author(s):  
Rania M. Khashaba ◽  
Mervet Moussa ◽  
Christopher Koch ◽  
Arthur R. Jurgensen ◽  
David M. Missimer ◽  
...  
Keyword(s):  
Calcium Phosphate ◽  
Setting Time ◽  
Chemical Characterization ◽  
Biological Properties ◽  
X Ray Diffraction ◽  
X Ray ◽  
Type Iii ◽  
Calcium Phosphate Cements ◽  
And Control

Aim. Physicochemical mechanical andin vitrobiological properties of novel formulations of polymeric calcium phosphate cements (CPCs) were investigated.Methods. Monocalcium phosphate, calcium oxide, and synthetic hydroxyapatite were combined with either modified polyacrylic acid, light activated polyalkenoic acid, or polymethyl vinyl ether maleic acid to obtain Types I, II, and III CPCs. Setting time, compressive and diametral strength of CPCs was compared with zinc polycarboxylate cement (control). Specimens were characterized using X-ray diffraction, scanning electron microscopy, and infrared spectroscopy.In vitrocytotoxicity of CPCs and control was assessed.Results. X-ray diffraction analysis showed hydroxyapatite, monetite, and brushite. Acid-base reaction was confirmed by the appearance of stretching peaks in IR spectra of set cements. SEM revealed rod-like crystals and platy crystals. Setting time of cements was 5–12 min. Type III showed significantly higher strength values compared to control. Type III yielded high biocompatibility.Conclusions. Type III CPCs show promise for dental applications.

Effect of coating method on release of Glimepiride from porosity osmotic pump tablets (POPTs)

2020 ◽  
pp. 37-45
Keyword(s):  
In Vitro Release ◽  
Osmotic Pump ◽  
Release Time ◽  
Once Daily ◽  
Coating Solution ◽  
Continuous Release ◽  
Red Color ◽  
Coating Method ◽  
Osmotic Agent

In this study, once-daily porosity osmotic pump tablets (POPTs) of Glimepiride were prepared using HPMC K100M (61%), osmotic agent (30% NaCl) coated using two different coating techniques spraying and dipping methods. The coating solution composed of ethyl cellulose (7.5%) w\w in ethanol (90%), castor oil (2%) as water-insoluble plasticizer and Gingo red color (0.5% w\w). In both techniques, the coating level was adjusted to give a 10% increase in the weight of the tablets. The effect of the coating by dipping technique with an increase in the weight of tablet (10 %, 20% & 50%) was also investigated to see the effect coating level on the percentage of drug release from POPTs. The results of the in vitro release of Glimepiride from tablets coated by the spraying method showed longer release time (24 hrs) than those coated with dipping method. On the other hand, increasing the coating level by dipping method retarded the release of the drug from tablets. However, the same retardation effect on release as shown with the spraying technique was only obtained by increasing the coating level with a 50% increase in the weight of the tablet. Thus, coating by spraying is more efficient to prepare POPTs to give a continuous release of Glimepiride from once daily table with the lowest increase in the total weight of the tablet.

Development of Solid Lipid Nanoparticles of Lamivudine for Brain Targeting

2009 ◽  
Vol 1 (1) ◽  
Author(s):  
Pravin Patil ◽  
Anil Sharma ◽  
Subhash Dadarwal ◽  
Vijay Sharma
Keyword(s):  
Drug Delivery ◽  
Drug Release ◽  
Solid Lipid Nanoparticles ◽  
Rotation Speed ◽  
Lipid Nanoparticles ◽  
Brain Targeting ◽  
Brain Penetration ◽  
Solid Lipid ◽  
Diffusion Technique

The objective of present investigation was to enhance brain penetration of Lamivudine, one of the most widely used drugs for the treatment of AIDS. This was achieved through incorporating the drug into solid lipid nanoparticles (SLN) prepared by using emulsion solvent diffusion technique. The formulations were characterized for surface morphology, size and size distribution, percent drug entrapment and drug release. The optimum rotation speed, resulting into better drug entrapment and percent yield, was in the range of 1000-1250 r/min. In vitro cumulative % drug release from optimized SLN formulation was found 40-50 % in PBS (pH-7.4) and SGF (pH-1.2) respectively for 10 h. After 24 h more than 65 % of the drug was released from all formulations in both mediums meeting the requirement for drug delivery for prolong period of time.

Preincubation with Sn-complexes causes intensive intracellular retention of 99mTc in thyroid cells in vitro

2012 ◽  
Vol 51 (05) ◽  
pp. 179-185 ◽  
Author(s):  
M. Wendisch ◽  
D. Aurich ◽  
R. Runge ◽  
R. Freudenberg ◽  
J. Kotzerke ◽  
...  
Keyword(s):  
Cell Model ◽  
Low Energy ◽  
Thyroid Cells ◽  
Low Energy Electrons ◽  
A Cell ◽  
Vitro Model ◽  
Uptake Studies ◽  
Radiobiological Effects ◽  
Radioactivity Retention

SummaryTechnetium radiopharmaceuticals are well established in nuclear medicine. Besides its well-known gamma radiation, 99mTc emits an average of five Auger and internal conversion electrons per decay. The biological toxicity of these low-energy, high-LET (linear energy transfer) emissions is a controversial subject. One aim of this study was to estimate in a cell model how much 99mTc can be present in exposed cells and which radiobiological effects could be estimated in 99mTc-overloaded cells. Methods: Sodium iodine symporter (NIS)- positive thyroid cells were used. 99mTc-uptake studies were performed after preincubation with a non-radioactive (cold) stannous pyro - phosphate kit solution or as a standard 99mTc pyrophosphate kit preparation or with pure pertechnetate solution. Survival curves were analyzed from colony-forming assays. Results: Preincubation with stannous complexes causes irreversible intracellular radioactivity retention of 99mTc and is followed by further pertechnetate influx to an unexpectedly high 99mTc level. The uptake of 99mTc pertechnetate in NIS-positive cells can be modified using stannous pyrophosphate from 3–5% to >80%. The maximum possible cellular uptake of 99mTc was 90 Bq/cell. Compared with nearly pure extracellular irradiation from routine 99mTc complexes, cell survival was reduced by 3–4 orders of magnitude after preincubation with stannous pyrophosphate. Conclusions: Intra cellular 99mTc retention is related to reduced survival, which is most likely mediated by the emission of low-energy electrons. Our findings show that the described experiments constitute a simple and useful in vitro model for radiobiological investigations in a cell model.

Preparation, Characterization and In-vitro release of Piroxicam-loaded Solid Lipid Nanoparticles

2010 ◽  
Vol 3 (3) ◽  
pp. 1136-1146
Author(s):  
V K Verma ◽  
Ram A
Keyword(s):  
Electron Microscopy ◽  
Particle Size ◽  
Solid Lipid Nanoparticles ◽  
In Vitro Release ◽  
Entrapment Efficiency ◽  
Lipid Nanoparticles ◽  
Diffusion Method ◽  
Solid Lipid ◽  
Vitro Release

 Solid lipid nanoparticles (SLNs) of piroxicam where produced by solvent emulsification diffusion method in a solvent saturated system. The SLNs where composed of tripamitin lipid, polyvinyl alcohol (PVAL) stabilizer, and solvent ethyl acetate. All the formulation were subjected to particle size analysis, zeta potential, drug entrapment efficiency, percent drug loading determination and in-vitro release studies. The SLNs formed were nano-size range with maximum entrapment efficiency. Formulation with 435nm in particle size and 85% drug entrapment was subjected to scanning electron microscopy (SEM) and transmission electron microscopy (TEM) for surface morphology, differential scanning calorimetry (DSC) for thermal analysis and short term stability studies. SEM and TEM confirm that the SLNs are nanometric size and circular in shape. The drug release behavior from SLNs suspension exhibited biphasic pattern with an initial burst and prolong release over 24 h. 

Solid Lipid Nanoparticles for Topical Delivery of Acitretin for the Treatment of Psoriasis by Design of Experiment

2020 ◽  
Vol 12 (2) ◽  
pp. 4474-4491
Author(s):  
Rajkumar Aland ◽  
Ganesan M ◽  
P. Rajeswara Rao ◽  
Bhikshapathi D. V. R. N.
Keyword(s):  
Particle Size ◽  
Drug Release ◽  
Solid Lipid Nanoparticles ◽  
Drug Loading ◽  
Entrapment Efficiency ◽  
Lipid Nanoparticles ◽  
Tem Analysis ◽  
In Vitro Drug Release ◽  
Solid Lipid

The main objective for this investigation is to develop and optimize the solid lipid nanoparticles formulation of acitretin for the effective drug delivery. Acitretin loaded SLNs were prepared by hot homogenization followed by the ultrasonication using Taguchi’s orthogonal array with eight parameters that could affect the particle size and entrapment efficiency. Based on the results from the analyses of the responses obtained from Taguchi design, three different independent variables including surfactant concentration (%), lipid to drug ratio (w/w) and sonication time (s) were selected for further investigation using central composite design. The  lipid Dynasan-116, surfactant poloxomer-188 and co surfactant egg lecithin resulted in better percent drug loading and evaluated for particle size, zeta potential, drug entrapment efficiency, in vitro drug release and stability. All parameters were found to be in an acceptable range. TEM analysis has demonstrated the presence of individual nanoparticles in spherical shape and the results were compatible with particle size measurements.  In vitro drug release of optimized SLN formulation (F2) was found to be 95.63 ± 1.52%, whereas pure drug release was 30.12 after 60 min and the major mechanism of drug release follows first order kinetics release data for optimized formulation (F2) with non-Fickian (anomalous) with a strong correlation coefficient (R2 = 0.94572) of Korsemeyer-Peppas model. The total drug content of acitretin gel formulation was found to 99.86 ± 0.012% and the diameter of gel formulation was 6.9 ± 0.021 cm and that of marketed gel was found to be 5.7 ± 0.06 cm, indicating better spreadability of SLN based gel formulation. The viscosity of gel formulation at 5 rpm was found to be 6.1 x 103 ± 0.4 x 103 cp. The release rate (flux) of acitretin across the membrane and excised skin differs significantly, which indicates about the barrier properties of skin. The flux value for SLN based gel formulation (182.754 ± 3.126 μg cm−2 h−1) was found to be higher than that for marketed gel (122.345 ± 4.786 μg cm−2 h−1). The higher flux and Kp values of SLN based gel suggest that it might be able to enter the skin easily as compared with marketed gel with an advantage of low interfacial tension of the emulsifier film that ensures an excellent contact to the skin. This topically oriented SLN based gel formulation could be useful in providing site-specific dermal treatment of psoriasis

Sign in / Sign up

Export Citation Format

Share Document