scholarly journals Inkjet Printing Infiltration of the Doped Ceria Interlayer in Commercial Anode-Supported SOFCs

Nanomaterials ◽  
2021 ◽  
Vol 11 (11) ◽  
pp. 3095
Author(s):  
Rumen I. Tomov ◽  
Thomas B. Mitchel-Williams ◽  
Eleonora Venezia ◽  
Michal Kawalec ◽  
Mariusz Krauz ◽  
...  
Keyword(s):  
Inkjet Printing ◽  
Low Cost ◽  
Single Step ◽  
Pure Hydrogen ◽  
Doped Ceria ◽  
Maximum Power Density ◽  
Ohmic Resistance ◽  
Porous Cathode ◽  
Ohmic Losses ◽  
Porous Interlayer

Single-step inkjet printing infiltration with doped ceria Ce0.9Ye0.1O1.95 (YDC) and cobalt oxide (CoxOy) precursor inks was performed in order to modify the properties of the doped ceria interlayer in commercial (50 × 50 × 0.5 mm3 size) anode-supported SOFCs. The penetration of the inks throughout the La0.8Sr0.2Co0.5Fe0.5O3−δ porous cathode to the Gd0.1Ce0.9O2 (GDC) interlayer was achieved by optimisation of the inks’ rheology jetting parameters. The low-temperature calcination (750 °C) resulted in densification of the Gd-doped ceria porous interlayer as well as decoration of the cathode scaffold with nanoparticles (~20–50 nm in size). The I–V testing in pure hydrogen showed a maximum power density gain of ~20% at 700 °C and ~97% at 800 °C for the infiltrated cells. The latter effect was largely assigned to the improvement in the interfacial Ohmic resistance due to the densification of the interlayer. The EIS study of the polarisation losses of the reference and infiltrated cells revealed a reduction in the activation polarisations losses at 700 °C due to the nano-decoration of the La0.8Sr0.2Co0.5Fe0.5O3−δ scaffold surface. Such was not the case at 800 °C, where the drop in Ohmic losses was dominant. This work demonstrated that single-step inkjet printing infiltration, a non-disruptive, low-cost technique, can produce significant and scalable performance enhancements in commercial anode-supported SOFCs.

Electrochemical Properties of Perovskite Cathode for Solid Oxide Fuel Cell

2007 ◽  
Vol 544-545 ◽  
pp. 985-988 ◽  
Author(s):  
Go Hiramatsu ◽  
Yoshihiro Hirata ◽  
Soichiro Sameshima ◽  
Naoki Matsunaga
Keyword(s):  
Fuel Cell ◽  
Electrochemical Properties ◽  
Electric Power ◽  
Solid Oxide ◽  
Doped Ceria ◽  
Oxide Fuel ◽  
Maximum Power Density ◽  
Ohmic Resistance ◽  
Terminal Voltage ◽  
Ceria Electrolyte

Gd-doped ceria electrolyte (Ce0.8Gd0.2O1.9, GDC, 700 μm thick), 30 vol% Ni-GDC cermet anode and perovskite cathode La0.6Sr0.4CoO3 (LSC) or La0.6Sr0.4Co0.2Fe0.8O3 (LSCF) were used to evaluate the electric power of the cell using 3 vol%-H2O containing H2 fuel at 873 and 1073 K. Terminal voltage, ohmic resistance and overpotential were analyzed during the operation of the cell. The maximum power density with LSC and LSCF cathode was 53 and 113 mW/cm2 at 1073 K, respectively. The ohmic resistance and overpotential at the cathode was smaller for LSCF than for LSC.

Fabrication of 3D Temperature Sensor Using Magnetostrictive Inkjet Printhead

2020 ◽  
Vol 64 (5) ◽  
pp. 50405-1-50405-5
Author(s):  
Young-Woo Park ◽  
Myounggyu Noh
Keyword(s):  
Flexible Electronics ◽  
Inkjet Printing ◽  
Temperature Sensor ◽  
Computer Aided Design ◽  
Low Cost ◽  
Three Dimensional ◽  
Drop On Demand ◽  
Aided Design ◽  
Nanoparticle Ink ◽  
Inkjet Printhead

Abstract Recently, the three-dimensional (3D) printing technique has attracted much attention for creating objects of arbitrary shape and manufacturing. For the first time, in this work, we present the fabrication of an inkjet printed low-cost 3D temperature sensor on a 3D-shaped thermoplastic substrate suitable for packaging, flexible electronics, and other printed applications. The design, fabrication, and testing of a 3D printed temperature sensor are presented. The sensor pattern is designed using a computer-aided design program and fabricated by drop-on-demand inkjet printing using a magnetostrictive inkjet printhead at room temperature. The sensor pattern is printed using commercially available conductive silver nanoparticle ink. A moving speed of 90 mm/min is chosen to print the sensor pattern. The inkjet printed temperature sensor is demonstrated, and it is characterized by good electrical properties, exhibiting good sensitivity and linearity. The results indicate that 3D inkjet printing technology may have great potential for applications in sensor fabrication.

Printing ultrathin graphene oxide nanofiltration membranes for water purification

2017 ◽  
Vol 5 (39) ◽  
pp. 20860-20866 ◽  
Author(s):  
Mahdi Fathizadeh ◽  
Huynh Ngoc Tien ◽  
Konstantin Khivantsev ◽  
Jung-Tsai Chen ◽  
Miao Yu
Keyword(s):  
Graphene Oxide ◽  
Water Purification ◽  
Inkjet Printing ◽  
Low Cost ◽  
Nanofiltration Membranes ◽  
Highly Effective ◽  
First Time ◽  
Polymeric Supports ◽  
Effective Water

We demonstrated for the first time that inkjet printing can be a low-cost, easy, fast, and scalable method for depositing ultrathin (7.5–60 nm) uniform graphene oxide (GO) nanofiltration membranes on polymeric supports for highly effective water purification.

Influence of Composition of Gd-Doped Ceria Electrolyte on Performance of Solid Oxide Fuel Cell

2012 ◽  
Vol 724 ◽  
pp. 389-392 ◽  
Author(s):  
Yuta Ibusuki ◽  
Yoshihiro Hirata ◽  
Soichiro Sameshima ◽  
Naoki Matsunaga
Keyword(s):  
Power Density ◽  
Open Circuit ◽  
Solid Oxide ◽  
Maximum Power ◽  
Cell Performance ◽  
Excess Oxygen ◽  
Doped Ceria ◽  
Oxide Fuel ◽  
Maximum Power Density ◽  
Oxide Ion Conductivity

Cell performance was measured for four types of Ni (40 vol%)-Gd-doped ceria (GDC) anode-supported solid oxide fuel cells with GDC electrolyte (40-120 μm thickness) of Ce1-xGdxO2-x/2 compositions (x = 0.05, 0.1, 0.15 and 0.2) at 773-1073 K using a H2 fuel. (La0.8Sr0.2)(Co0.8Fe0.2)O3 cathode was printed on the GDC films. The open circuit voltage and maximum power density at 873-1073 K showed a maximum at x = 0.1. The maximum power density at x = 0.1 was 166 and 506 mW/cm2 at 873 and 1073 K, respectively. The excess oxygen vacancy at x = 0.1-0.2, which does not contribute to the oxide ion conductivity, reacts with a H2 fuel to form electrons (H2 + VO 2H+ + VO×, VO× VO + 2e-). This reaction reduces the cell performance.

scholarly journals Circular polarised antenna fabricated with low‐cost 3D and inkjet printing equipment

2017 ◽  
Vol 53 (6) ◽  
pp. 370-371 ◽  
Author(s):  
S. Jun ◽  
B. Sanz‐Izquierdo ◽  
J. Heirons ◽  
C.X. Mao ◽  
S. Gao ◽  
...  
Keyword(s):  
Inkjet Printing ◽  
Low Cost

Alternative technology concepts for low-cost and high-speed 2D and 3D interconnect manufacturing

2013 ◽  
Vol 2013 (1) ◽  
pp. 000001-000006
Author(s):  
F. Roozeboom ◽  
M. Smets ◽  
B. Kniknie ◽  
M. Hoppenbrouwers ◽  
G. Dingemans ◽  
...  
Keyword(s):  
High Speed ◽  
Room Temperature ◽  
Microelectromechanical Systems ◽  
Low Cost ◽  
Industrial Process ◽  
Atomic Layer ◽  
Single Step ◽  
Thermal Mode ◽  
Different Types ◽  
Sidewall Passivation

The current industrial process of choice for Deep Reactive Ion Etching (DRIE) of 3D features, e.g. Through-Silicon Vias (TSVs), Microelectromechanical Systems (MEMS), etc., is the Bosch process, which uses alternative SF6 etch cycles and C4F8-based sidewall passivation cycles in a time-sequenced mode. An alternative, potentially faster and more accurate process is to have wafers pass under spatially-divided reaction zones, which are individually separated by so-called N2-gas bearings ‘curtains’ of heights down to 10–20 μm. In addition, the feature sidewalls can be protected by replacing the C4F8-based sidewall passivation cycles by cycles forming chemisorbed and highly uniform passivation layers of Al2O3 or SiO2 deposited by Atomic Layer Deposition (ALD), also in a spatially-divided mode. ALD is performed either in thermal mode, or plasma-assisted mode in order to achieve near room-temperature processing. For metal filling of 3D-etched TSVs, or for deposition of 2D metal conductor lines one can use Laser-Induced Forward Transfer (LIFT) of metals. LIFT is a maskless, ‘solvent’-free deposition method, utilizing different types of pulsed lasers to deposit thin material (e.g. Cu, Au, Al, Cr) layers with μm-range resolution from a transparent carrier (ribbon) onto a close-by acceptor substrate. It is a dry, single-step, room temperature process in air, suitable for different types of interconnect fabrication, e.g. TSV filling and redistribution layers (RDL), without the use of wet chemistry.

Preparation of Ce0.8Sm0.2O1.9 Thin Films by Electrophoretic Deposition and their Fuel Cell Performance

2013 ◽  
Vol 566 ◽  
pp. 137-140 ◽  
Author(s):  
Hiroki Ichiboshi ◽  
Kenichi Myoujin ◽  
Takayuki Kodera ◽  
Takashi Ogihara
Keyword(s):  
Thin Films ◽  
Fuel Cell ◽  
Spray Pyrolysis ◽  
Power Density ◽  
Electrophoretic Deposition ◽  
Open Circuit Voltage ◽  
Open Circuit ◽  
Doped Ceria ◽  
Maximum Power Density ◽  
Fuel Cell Performance

Ce0.8Sm0.2O1.9 (Samaria-doped ceria: SDC) precursors were synthesized by carbon-assisted spray pyrolysis. SDC thin films were prepared by electrophoretic deposition using the SDC precursor particles. The as-prepared SDC thin films were sintered at 1600 °C for 10 h. Uniform films with a thickness of approximately 20 μm were obtained. A fuel cell using the prepared thin films showed a maximum power density of 60.6 mW/cm2 and an open circuit voltage (OCV) of 0.63 V at 700 °C.

Experimental Investigation of Microfluidic Feature Manufacturing by Digital Light Processing Stereolithography

2020 ◽  
Author(s):  
Lara Rebaioli ◽  
Irene Fassi
Keyword(s):  
Process Parameters ◽  
Low Cost ◽  
Dimensional Accuracy ◽  
Machine Building ◽  
Single Step ◽  
Main Process ◽  
Single Chip ◽  
Digital Light Processing ◽  
And Performance ◽  
User Friendly

Abstract Lab on Chips (LOCs) are devices, mostly based on microfluidics, that allow to perform one or several chemical, biochemical or biological analysis in a miniaturized format on a single chip. The Additive Manufacturing processes, and in particular the Digital Light Processing stereolithography (DLP-SLA), could quickly produce a complete LOC with high resolution 3D features in a single step, i.e. without the need for assembly processes, and using low cost and user-friendly desktop machines. However, the potential of DLP-SLA to produce non-planar channels or channels with complex sections has not been fully investigated yet. This study proposes a benchmark artifact (including also some channels with their axis lying in a plane parallel to the machine building platform) aiming at assessing the capability and performance of DLP-SLA for manufacturing microfeatures for microfluidic devices. A proper experimental campaign was performed to evaluate the effect of the main process parameters (namely, layer thickness and exposure time) on the process performance. The results pointed out that both the process parameters influence the quality and dimensional accuracy of the analyzed features.

scholarly journals Efficient One-Pot Synthesis of a Hexamethylenetetramine-Doped Cu-BDC Metal-Organic Framework with Enhanced CO2 Adsorption

Nanomaterials ◽  
2019 ◽  
Vol 9 (8) ◽  
pp. 1063 ◽  
Author(s):  
Aisha Asghar ◽  
Naseem Iqbal ◽  
Tayyaba Noor ◽  
Majid Ali ◽  
Timothy L. Easun
Keyword(s):  
Co2 Adsorption ◽  
Low Cost ◽  
Metal Organic Framework ◽  
Single Step ◽  
Co2 Uptake ◽  
One Pot ◽  
Amine Functionalized ◽  
Metal Organic ◽  
Thermogravimetric Studies ◽  
Organic Framework

Herein we report a facile, efficient, low cost, and easily scalable route for an amine-functionalized MOF (metal organic framework) synthesis. Cu-BDC⊃HMTA (HMTA = hexamethylenetetramine) has high nitrogen content and improved thermal stability when compared with the previously reported and well-studied parent Cu-BDC MOF (BDC = 1,4-benzenedicarboxylate). Cu-BDC⊃HMTA was obtained via the same synthetic method, but with the addition of HMTA in a single step synthesis. Thermogravimetric studies reveal that Cu-BDC⊃HMTA is more thermally stable than Cu-BDC MOF. Cu-BDC⊃HMTA exhibited a CO2 uptake of 21.2 wt % at 273 K and 1 bar, which compares favorably to other nitrogen-containing MOF materials.

Sign in / Sign up

Export Citation Format

Share Document