scholarly journals Synthesis and Characterization of Dental Nanocomposite Resins Filled with Different Clay Nanoparticles

Polymers ◽  
2019 ◽  
Vol 11 (4) ◽  
pp. 730 ◽  
Author(s):  
Alexandros K. Nikolaidis ◽  
Elisabeth A. Koulaouzidou ◽  
Christos Gogos ◽  
Dimitris S. Achilias
Keyword(s):  
Flexural Modulus ◽  
Organic Matrix ◽  
Displacement Transducer ◽  
Filler Loading ◽  
Degree Of Conversion ◽  
Dental Resin ◽  
Polymerization Shrinkage ◽  
Clay Nanoparticles ◽  
Linear Variable Displacement Transducer ◽  
Electron Microscopy Analysis

Nanotechnology comprises a promising approach towards the update of dental materials.The present study focuses on the reinforcement ofdental nanocomposite resins with diverse organomodified montmorillonite (OMMT) nanofillers. The aim is to investigate whether the presence of functional groups in the chemical structure of the nanoclay organic modifier may virtually influence the physicochemical and/or the mechanical attitude of the dental resin nanocomposites. The structure and morphology of the prepared materials were investigated by means of wide angle X-ray diffraction and scanning electron microscopy analysis. Fourier transform infrared spectroscopy was used to determine the variation of the degree of conversion over time. Measurements of polymerization shrinkage and mechanical properties were conducted with a linear variable displacement transducer apparatus and a dynamometer, respectively. All the obtained nanocomposites revealed intercalated structures and most of them had an extensive filler distribution into the polymer matrix. Polymerization kinetics werefound to be influenced by the variance of the clay organomodifier, whilenanoclays with vinyl groups considerably increased the degree of conversion. Polymerization shrinkage was almost limited up to 50% by incorporating nanoclays. The absence of reactive groups in the OMMT structure may retain setting contraction atlow levels. An enhancement of the flexural modulus was observed, mainly by using clay nanoparticles decorated with methacrylated groups, along with a decrease in the flexural strength at a high filler loading. The overall best performance was found for the nanocomposites with OMMTs containing double bonds. The significance of the current work relies on providing novel information about chemical interactions phenomena between nanofillers and the organic matrix towards the improvement of dental restorative materials.

scholarly journals Effect of 4-(N,N-dimethylamino)phenethyl Alcohol on Degree of Conversion and Cytotoxicity of Photo-Polymerized CQ-Based Resin Composites

2014 ◽  
Vol 25 (6) ◽  
pp. 538-542 ◽  
Author(s):  
Dayane Carvalho Ramos Salles de Oliveira ◽  
Camila Batista da Silva ◽  
Bruno Vilela Muniz ◽  
Maria C. Volpato ◽  
Ana Rosa Costa ◽  
...  
Keyword(s):  
Organic Matrix ◽  
Human Keratinocytes ◽  
Filler Loading ◽  
Degree Of Conversion ◽  
Control Group ◽  
Resin Composites ◽  
Cytotoxic Effects ◽  
Phenethyl Alcohol ◽  
Significant Difference ◽  
Post Hoc

The aim of this study was to evaluate the degree of conversion (DC) and the cytotoxicity of photo-cured experimental resin composites containing 4-(N,N-dimethylamino)phenethyl alcohol (DMPOH) combined to the camphorquinone (CQ) compared with ethylamine benzoate (EDAB). The resin composites were mechanically blended using 35 wt% of an organic matrix and 65 wt% of filler loading. To this matrix was added 0.2 wt% of CQ and 0.2 wt% of one of the reducing agents tested. 5x1 mm samples (n=5) were previously submitted to DC measurement and then pre-immersed in complete culture medium without 10% (v/v) bovine serum for 1 h or 24 h at 37 °C in a humidifier incubator with 5% CO2 and 95% humidity to evaluate the cytotoxic effects of experimental resin composites using the MTT assay on immortalized human keratinocytes cells. As a result of absence of normal distribution, the statistical analysis was performed using the nonparametric Kruskal-Wallis to evaluate the cytotoxicity and one-way analysis of variance to evaluate the DC. For multiple comparisons, cytotoxicity statistical analyses were submitted to Student-Newman-Keuls and DC analysis to Tukey's HSD post-hoc test (=0.05). No significant differences were found between the DC of DMPOH (49.9%) and EDAB (50.7%). 1 h outcomes showed no significant difference of the cell viability between EDAB (99.26%), DMPOH (94.85%) and the control group (100%). After 24 h no significant difference were found between EDAB (48.44%) and DMPOH (38.06%), but significant difference was found compared with the control group (p>0.05). DMPOH presented similar DC and cytotoxicity compared with EDAB when associated with CQ.

scholarly journals Polymerization shrinkage behaviour of resin composites functionalized with unsilanized bioactive glass fillers

2020 ◽  
Vol 10 (1) ◽  
Author(s):  
Matej Par ◽  
Dirk Mohn ◽  
Thomas Attin ◽  
Zrinka Tarle ◽  
Tobias T. Tauböck
Keyword(s):  
Bioactive Glass ◽  
Degree Of Conversion ◽  
Stress Rate ◽  
Partial Replacement ◽  
Shrinkage Stress ◽  
Resin Composites ◽  
Dental Resin ◽  
Polymerization Shrinkage ◽  
Reinforcing Fillers ◽  
Shrinkage Behaviour

Abstract Previous work has shown that partial replacement of reinforcing fillers with unsilanized silica particles can diminish polymerization shrinkage stress of dental resin composites. The aim of the present study was to investigate whether such an effect can be attained by using unsilanized bioactive glass (BG). Incorporating BG fillers into resin composites is interesting due to their potential for exerting caries-preventive effects. Experimental light-curable composites with a total filler load of 77 wt% were prepared. Reinforcing fillers were partially replaced with 0–60 wt% of BG 45S5 and an experimental low-sodium fluoride-containing BG. The following properties were investigated: linear shrinkage, degree of conversion, shrinkage stress, maximum shrinkage stress rate, and time to achieve maximum shrinkage stress rate. The diminishing effect of BG 45S5 on shrinkage stress was mediated by a decrease in degree of conversion caused by this BG type. In contrast, as the degree of conversion remained unaffected by the experimental BG, the resulting shrinkage behaviour was governed by the effect of varying amounts of silanized and unsilanized fillers on material’s viscoelastic properties. The replacement of silanized reinforcing fillers with unsilanized BG did not reduce polymerization shrinkage stress unless the reduction was attained indirectly through a diminished degree of conversion.

scholarly journals Improved performance of Bis-GMA dental composites reinforced with surface-modified PAN nanofibers

2021 ◽  
Vol 32 (7) ◽  
Author(s):  
Parisa Amiri ◽  
Zahra Talebi ◽  
Dariush Semnani ◽  
Rouhollah Bagheri ◽  
Hossein Fashandi
Keyword(s):  
Network Formation ◽  
Resin Composite ◽  
Flexural Modulus ◽  
Weight Ratio ◽  
Dental Composite ◽  
Dental Composites ◽  
Resin Matrix ◽  
Dental Resin ◽  
Polymerization Shrinkage ◽  
Surface Modified

AbstractIn the present work, polyacrylonitrile (PAN) nanofibers reinforced dental composites were investigated to achieve the improved interfacial adhesion between the PAN nanofiber and resin matrix using surface modification of nanofibers. PAN nanofibers mat were prepared by electrospinning and then, surface treated with the activated bisphenol A glycidyl methacrylate (Bis-GMA)/triethyleneglycol dimethacrylate (TEGDMA) (50/50 mass ratio) dental resin followed by photo-curing. Also, the treated nanofibers mat was milled into a powder to achieve the uniform distribution of nanofibers in the matrix resin. The reinforced dental composite were prepared by mixing the various mass fraction of the powder (0.5–15 wt%) with the Bis-GMA/TEGDMA dental monomers. The effect of weight ratio of surface-modified nanofibers to blend resin on the chemical structure, morphology, compression and flexural properties, color and polymerization shrinkage of dental composites was evaluated. The results showed that using surface-treated nanofibers with content of 5 wt% enhanced the compression strength, flexural strength, flexural modulus and work of rupture of the resultant dental composite by factors of 23%, 7%, 80%, and 145%, respectively, comparing to the unreinforced neat resin. Also, the polymerization shrinkage reduces by 37%. These significant improved properties of the dental composite could be due to the semi-interpenetration network formation between surface-modified nanofibers and resin matrix and well distribution of nanofibers in the dental resin. Further increasing the nanofiber content led to poor mechanical properties of obtained dental composites. The results also, revealed that the color of resin composite could be whiter using modified PAN nanofibers as the filler.

The Combination of CQ-amine and TPO Increases the Polymerization Shrinkage Stress and Does Not Improve the Depth of Cure of Bulk-fill Composites

2019 ◽  
Vol 44 (5) ◽  
pp. 499-509
Author(s):  
MG Rocha ◽  
DCRS de Oliveira ◽  
MAC Sinhoreti ◽  
JF Roulet ◽  
AB Correr
Keyword(s):  
Near Infrared ◽  
Light Emitting Diode ◽  
Flexural Modulus ◽  
Degree Of Conversion ◽  
Light Transmittance ◽  
Volumetric Shrinkage ◽  
Shrinkage Stress ◽  
Polymerization Shrinkage ◽  
Depth Of Cure ◽  
Three Point Bend Test

SUMMARY Objectives: To evaluate the effect of combining camphorquinone (CQ) and diphenyl(2,4,6-trimethylbenzoyl)phosphine oxide (TPO) on the depth of cure and polymerization shrinkage stress of bulk-fill composites. Methods and Materials: Experimental bulk-fill composites were produced containing equal molar concentrations of either CQ-amine or CQ-amine/TPO. The degree of in-depth conversion through each millimeter of a 4-mm-thick bulk-fill increment was evaluated by Fourier transform near-infrared microspectroscopy using a central longitudinal cross section of the increment of each bulk-fill composite (n=3). Light-transmittance of the multi-wave light-emitting diode (LED) emittance used for photoactivation (Bluephase G2, Ivoclar Vivadent) was recorded through every millimeter of each bulk-fill composite using spectrophotometry. The volumetric shrinkage and polymerization shrinkage stress were assessed using a mercury dilatometer and the Bioman, respectively. The flexural modulus was also assessed by a three-point bend test as a complementary test. Data were analyzed according to the different experimental designs (α=0.05 and β=0.2). Results: Up to 1 mm in depth, adding TPO to CQ-based bulk-fill composites increased the degree of conversion, but beyond 1 mm no differences were found. The light-transmittance of either wavelengths emitted from the multi-wave LED (blue or violet) through the bulk-fill composites were only different up to 1 mm in depth, regardless of the photoinitiator system. Adding TPO to CQ-based bulk-fill composites did not affect volumetric shrinkage but did increase the flexural modulus and polymerization shrinkage stress. Conclusion: Adding TPO to CQ-based bulk-fill composites did not increase the depth of cure. However, it did increase the degree of conversion on the top of the restoration, increasing the polymerization shrinkage stress.

scholarly journals Solvent Degradation and Polymerization Shrinkage Reduction of Resin Composites Using Isobornyl Methacrylate

2019 ◽  
Vol 30 (3) ◽  
pp. 272-278 ◽  
Author(s):  
Jamille Favarão ◽  
Dayane Carvalho Ramos Salles de Oliveira ◽  
Mateus Garcia Rocha ◽  
Maurício Matté Zanini ◽  
Gabriel Flores Abuna ◽  
...  
Keyword(s):  
Flexural Modulus ◽  
Knoop Hardness ◽  
Resin Matrix ◽  
Control Group ◽  
Resin Composites ◽  
Gap Formation ◽  
Dental Resin ◽  
Similar Reduction ◽  
Polymerization Shrinkage ◽  
Ft Ir

Abstract The aim of this study was to use the isobornyl methacrylate (IBOMA) as a combining or substituent diluent monomer in the resin matrix of dental resin composites. Thus, the resin matrix was formulated with 60 wt% of BisGMA and 40 wt% of diluent monomers. TEGDMA as the only diluent monomer was used as control with 40 wt%, while total substitution of TEGDMA was done with 40 wt% of IBOMA. The combination of IBOMA and TEGDMA was done with 20 wt% of each monomer. To the resin matrix, 65 wt% of filler particles was added. Degree of conversion (DC) using FT-IR, flexural strength (FS), flexural modulus (FM), polymerization shrinkage by gap formation (GF), Knoop hardness (KH) and solvent degradation (SD) were evaluated. Data were analyzed using ANOVA and Tukey’s test (α=0.05; b=0.2). The results showed that reducing or substituting TEGDMA using IBOMA did not affect the DC (0.085), FS (p=0.886) or FM (p=0.414). Also, when IBOMA was used, lower GF was found in comparison to the control containing only TEGDMA as the diluent monomer (p=0.032). However, even though all composites presented reduction in KH during the SD test, the combination of IBOMA and TEGDMA showed similar reduction in KHN in comparison to the control group (p=0.001), while the total substitution of TEGDMA with IBOMA decreased KHN after SD (p=0.041). Thus, the combination of IBOMA and TEGDMA seem to reduce SD and GF without affecting the properties of resin composites.

Properties of a New Nanofiber Restorative Composite

2019 ◽  
Vol 44 (1) ◽  
pp. 34-41 ◽  
Author(s):  
EM Yancey ◽  
W Lien ◽  
CS Nuttall ◽  
JA Brewster ◽  
HW Roberts ◽  
...  
Keyword(s):  
Flexural Strength ◽  
Hybrid Composites ◽  
Flexural Modulus ◽  
Testing Machine ◽  
Degree Of Conversion ◽  
Imaging Device ◽  
Polymerization Shrinkage ◽  
Depth Of Cure ◽  
Curing Shrinkage ◽  
Cylindrical Mold

SUMMARY A new nanofiber-reinforced hybrid composite (NovaPro Fill, Nanova) was recently introduced with reportedly improved mechanical properties. The purpose of this study was to compare the properties (flexural strength/modulus, degree of conversion [DC], depth of cure, and polymerization shrinkage) of the nanofiber composite to those of traditional hybrid composites (Filtek Z250, 3M ESPE; Esthet-X HD, Dentsply). To determine flexural strength and modulus, composite was placed in a rectangular mold, light-cured, stored for 24 hours, and then fractured in a universal testing machine. For degree of conversion, composite was placed in a cylindrical mold, light-cured, and stored for 24 hours. Measurements were made at the top and bottom surfaces using Fourier Transform Infrared Spectroscopy. To determine depth of cure, composite was placed in a cylindrical mold and light-cured. Uncured composite was scraped until polymerized resin was reached. Remaining composite was measured and divided by two. Polymerization shrinkage was determined by placing the composite material on a pedestal in a video-imaging device while light-curing. Shrinkage was determined after 10 minutes. Data were analyzed with one-way analysis of variance and Tukey post hoc test per property (α=0.05). Compared to Filtek Z250, NovaPro Fill had significantly lower flexural strength and modulus, greater volumetric shrinkage, and similar depth of cure, but greater top and bottom DC. Compared to Esthet-X HD, NovaPro Fill had similar flexural strength, shrinkage, and top and bottom DC, but significantly greater depth of cure and flexural modulus.

scholarly journals The Photoinitiators Used in Resin Based Dental Composite—A Review and Future Perspectives

Polymers ◽  
2021 ◽  
Vol 13 (3) ◽  
pp. 470
Author(s):  
Andrea Kowalska ◽  
Jerzy Sokolowski ◽  
Kinga Bociong
Keyword(s):  
Current Knowledge ◽  
Biomechanical Properties ◽  
Degree Of Conversion ◽  
Dental Composite ◽  
Polymerization Process ◽  
Dental Composites ◽  
Dental Resin ◽  
Dental Resins ◽  
Light Curing

The presented paper concerns current knowledge of commercial and alternative photoinitiator systems used in dentistry. It discusses alternative and commercial photoinitiators and focuses on mechanisms of polymerization process, in vitro measurement methods and factors influencing the degree of conversion and hardness of dental resins. PubMed, Academia.edu, Google Scholar, Elsevier, ResearchGate and Mendeley, analysis from 1985 to 2020 were searched electronically with appropriate keywords. Over 60 articles were chosen based on relevance to this review. Dental light-cured composites are the most common filling used in dentistry, but every photoinitiator system requires proper light-curing system with suitable spectrum of light. Alternation of photoinitiator might cause changing the values of biomechanical properties such as: degree of conversion, hardness, biocompatibility. This review contains comparison of biomechanical properties of dental composites including different photosensitizers among other: camphorquinone, phenanthrenequinone, benzophenone and 1-phenyl-1,2 propanedione, trimethylbenzoyl-diphenylphosphine oxide, benzoyl peroxide. The major aim of this article was to point out alternative photoinitiators which would compensate the disadvantages of camphorquinone such as: yellow staining or poor biocompatibility and also would have mechanical properties as satisfactory as camphorquinone. Research showed there is not an adequate photoinitiator which can be as sufficient as camphorquinone (CQ), but alternative photosensitizers like: benzoyl germanium or novel acylphosphine oxide photoinitiators used synergistically with CQ are able to improve aesthetic properties and degree of conversion of dental resin.

Micro Impact Testing of Lead Free Solder Joints

2008 ◽  
Vol 32 ◽  
pp. 99-102
Author(s):  
Ranjan Rajoo ◽  
Erich H. Kisi ◽  
D.J. O'Connor
Keyword(s):  
Solder Joint ◽  
High Strain Rate ◽  
Strain Rate ◽  
High Strain ◽  
Intermetallic Layer ◽  
Displacement Transducer ◽  
Impact Testing ◽  
Lead Free ◽  
Linear Variable Displacement Transducer ◽  
Free Solder

This paper presents data obtained from a newly-developed instrument to test the quality of solder interconnections at high strain rate – the ‘micro-impactor’. This shear test of the interconnection at high strain rate mimics the stress experienced by the solder joint when undergoing shock due to drop-impact. Instrumented with a load cell and linear variable displacement transducer (LVDT), it also has the ability to provide dynamic impact force and displacement data. Earlier concepts to characterise the solder joint at high strain rates such as the miniature pendulum impact tester [1] lacked this capability. This micro-impactor was used to study the effect of increasing silver (Ag) and copper (Cu) concentration in solder alloys on the shear strength of the solder joint. The performance of these lead-free alloys was also compared to that of the well-established leaded solder. It was found that increasing the silver content increases the yield strength of the solder, causing the failure to occur at the brittle intermetallic layer instead of in the bulk of the solder.

Physical–mechanical evaluation of a microhybrid and a nanofilled composite light activated by quartz-halogen tungsten and light-emitting diode

2018 ◽  
Vol 53 (7) ◽  
pp. 981-990
Author(s):  
Fernanda P Ritto ◽  
Eduardo Moreira da Silva ◽  
Hélio Rodrigues Sampaio-Filho ◽  
Raimundo A Lacerda ◽  
Márcio AP Borges ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Nuclear Magnetic Resonance ◽  
Light Emitting Diode ◽  
Degree Of Conversion ◽  
Dental Composite ◽  
Polymerization Shrinkage ◽  
Light Emitting ◽  
Scanning Electron

The aim of this study was to characterize organic and disperse phase of a microhybrid (Mh – Filtek Z250) and a nanofilled (Nf – Filtek Z350) dental composite and analyze the influence of two LCUs (QHT-quartz-halogen tungsten and LED – light-emitting diode) on its physical–mechanical properties (degree of conversion, polymerization shrinkage, Vickers hardness and diametral tensile strength). Surface morphology was studied by scanning electron microscopy. The disperse phase content was measured using thermogravimetric analysis (TGA) and the organic fractions were qualitatively analyzed by nuclear magnetic resonance spectroscopy. Physical–mechanical properties were analyzed varying dental composite and LCU: Mh-QHT, Nf-QHT, Mh-LED and Nf-LED. The degree of conversion was evaluated using Raman spectrophotometry and polymerization shrinkage was measured by water picnometry. Mechanical behavior was analyzed by Vickers microhardness and diametral tensile testing. Scanning electron microscopy analysis showed similar microstructure of the materials mainly composed with different-sized particles dispersed within methacrylate matrix. Thermogravimetric analysis shows 80.13% of inorganic fraction for microhybrid composite and 75.29% for nanofilled. Nuclear magnetic resonance analysis showed similar organic structure for composites and did not show the presence of the monomer TEGDMA. Different light sources did not influence the tested properties, but considering different composites, nanofilled showed the highest degree of conversion (Gr 2:77%, Gr 4: 79.4%). The study shows that when the optimum radiant exposure (24 J/cm2) was used for polymerization of composites, regardless of the polymerization source, the properties of these resin materials showed satisfactory and similar results in relation to the conversion of polymers, polymerization shrinkage and mechanical behavior.

Sign in / Sign up

Export Citation Format

Share Document