scholarly journals Mechanical Properties and Tribological Behavior of MoS2-Enhanced Cellulose-Based Biocomposites for Food Packaging

Polymers ◽  
2021 ◽  
Vol 13 (11) ◽  
pp. 1838
Author(s):  
Shih-Chen Shi ◽  
Pramod Kumar Mandal ◽  
Tao-Hsing Chen
Keyword(s):  
Mechanical Properties ◽  
Water Vapor ◽  
Food Packaging ◽  
Load Capacity ◽  
Hydroxypropyl Methylcellulose ◽  
Water Vapor Permeability ◽  
Synthetic Polymers ◽  
Tribological Performance ◽  
Vapor Permeability ◽  
Potential Candidate

Synthetic polymers are the most commonly used polymers in daily life. Therefore, it is necessary to develop environmentally friendly polymers. Hydroxypropyl methylcellulose (HPMC) is a potential candidate for a biopolymer, owing to its unique properties. However, HPMC biopolymers have some disadvantages compared to synthetic polymers. In this study, the mechanical properties and tribological performance of MoS2 additive-enhanced cellulose matrix biocomposites were investigated in order to improve the properties of HPMC. MoS2 was incorporated into the HPMC matrix as a strengthening additive. The mechanical properties, bonding, and water vapor permeability of the composites were analyzed. The mechanical and vapor barrier properties of the HPMC films were significantly enhanced. The ultimate tensile strength and Young’s modulus of the composite films increased with the addition of up to 1 wt% MoS2. The water vapor permeability of HPMC films reduced when additives were incorporated. The wear test proves that the MoS2 additives can improve the tribological performance of the HPMC composite while reducing the friction coefficient. The main reason for enhanced tribological performance is the improvement in load capacity of the composite coating by the MoS2 additive. This MoS2/HPMC biocomposite can be used in food packaging.

scholarly journals Application of Solution Blow Spinning for Rapid Fabrication of Gelatin/Nylon 66 Nanofibrous Film

Foods ◽  
2021 ◽  
Vol 10 (10) ◽  
pp. 2339
Author(s):  
Zhichao Yang ◽  
Chaoyi Shen ◽  
Yucheng Zou ◽  
Di Wu ◽  
Hui Zhang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Water Vapor ◽  
Composite Film ◽  
Food Packaging ◽  
Composite Films ◽  
Water Vapor Permeability ◽  
Vapor Permeability ◽  
Nylon 66 ◽  
Rapid Fabrication ◽  
Solution Blow Spinning

Gelatin (GA) is a natural protein widely used in food packaging, but its fabricated fibrous film has the defects of a high tendency to swell and inferior mechanical properties. In this work, a novel spinning technique, solution blow spinning (SBS), was used for the rapid fabrication of nanofiber materials; meanwhile, nylon 66 (PA66) was used to improve the mechanical properties and the ability to resist dissolution of gelatin films. Morphology observations show that GA/PA66 composite films had nano-diameter from 172.3 to 322.1 nm. Fourier transform infrared spectroscopy and X-ray indicate that GA and PA66 had strong interaction by hydrogen bonding. Mechanical tests show the elongation at break of the composite film increased substantially from 7.98% to 30.36%, and the tensile strength of the composite film increased from 0.03 MPa up to 1.42 MPa, which indicate that the composite films had the highest mechanical strength. Water vapor permeability analysis shows lower water vapor permeability of 9.93 g mm/m2 h kPa, indicates that GA/PA66 film’s water vapor barrier performance was improved. Solvent resistance analysis indicates that PA66 could effectively improve the ability of GA to resist dissolution. This work indicates that SBS has great promise for rapid preparation of nanofibrous film for food packaging, and PA66 can be applied to the modification of gelatin film.

scholarly journals Characterization of compisote edible films from aloe vera gel, beeswax and chitosan

10.5219/1177 ◽  
2019 ◽  
Vol 13 (1) ◽  
pp. 854-862 ◽  
Author(s):  
Usman Amin ◽  
Muhammad Azam Khan ◽  
Muhammad Ehtasham Akram ◽  
Abdel Rahman Mohammad Said Al-Tawaha ◽  
Alexey Laishevtcev ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Water Vapor ◽  
Food Packaging ◽  
Aloe Vera ◽  
Water Vapor Permeability ◽  
Edible Films ◽  
Vapor Permeability ◽  
Casting Technique ◽  
Edible Packaging ◽  
Superior Mechanical Properties

Environmental consciousness as well as individual’s demand for ready to eat food, recently, has changed the trends in food packaging leading to the development of biodegradable and edible packaging. Emulsified edible films have better transparency, superior mechanical properties and provide barriers to water and other atmospheric gases. Edible films if not consumed, biodegrad chemically. In present study, edible films were, initially, prepared using Chitosan and Aloe vera at different concentrations. Films were then subjected to physical and mechanical testing. Films with 20% Aloe vera had low thickness as compared to films with no Aloe vera. These films also had superior mechanical properties and lower water vapor permeability. Films with 20% Aloe vera were, then, selected and beeswax was dispersed in Chitosan-Aloe vera solution at concentration upto 2.0% followed by film preparation through casting technique. Thickness and water vapor permeability were observed to be improved with increase in concentration of beeswax. Tensile strength of edible films was also improved 1.3 times when concentration of beeswax increased from 0.5 to 2.0%. Percentage elongation decreased with increase in beeswax concentration in the emulsified films. No change in particle size was observed with change in concentration of beeswax. Emulsions were also stable at room temperatures. Decrease in transparency of emulsified edible films was observed with increase in beeswax content in the emulsified films. In addition, cost analysis of the films proved them reasonable to be used as an alternate of synthetic packaging materials.

scholarly journals Development of PE/PCL Bilayer Films Modified with Casein and Aluminum Oxide

Molecules ◽  
2021 ◽  
Vol 26 (11) ◽  
pp. 3090
Author(s):  
Anita Ptiček Siročić ◽  
Ana Rešček ◽  
Zvonimir Katančić ◽  
Zlata Hrnjak-Murgić
Keyword(s):  
Mechanical Properties ◽  
Thermal Properties ◽  
Water Vapor ◽  
Aluminum Oxide ◽  
Water Vapor Permeability ◽  
Vapor Permeability ◽  
Mechanical And Thermal Properties ◽  
Oxide Compound ◽  
Bilayer Films ◽  
Oxide Particles

The studied samples were prepared from polyethylene (PE) polymer which was coated with modified polycaprolactone (PCL) film in order to obtain bilayer films. Thin PCL film was modified with casein/aluminum oxide compound to enhance vapor permeability as well as mechanical and thermal properties of PE/PCL films. Casein/aluminum oxide modifiers were used in order to achieve some functional properties of polymer film that can be used in various applications, e.g., reduction of water vapor permeability (WVTR) and good mechanical and thermal properties. Significant improvement was observed in mechanical properties, especially in tensile strength as well as in water vapor values. Samples prepared with aluminum oxide particles indicated significantly lower values up to 60%, and samples that were prepared with casein and 5% Al2O3 showed the lowest WVTR value.

Fabrication of Composite Films Based on Chitosan and Vegetable-Tanned Collagen Fibers Crosslinked with Genipin

2021 ◽  
Vol 116 (10) ◽  
Author(s):  
Jie Liu ◽  
Yanchun Liu ◽  
Eleanor M. Brown ◽  
Zhengxin Ma ◽  
Cheng-Kung Liu
Keyword(s):  
Mechanical Properties ◽  
Thermal Stability ◽  
Water Vapor ◽  
Composite Film ◽  
Composite Films ◽  
Value Added ◽  
Water Vapor Permeability ◽  
Vapor Permeability ◽  
Leather Industry ◽  
Compact Structure

The leather industry generates considerable amounts of solid waste and raises many environmental concerns during its disposal. The presence of collagen in these wastes provides a potential protein source for the fabrication of bio-based value-added products. Herein, a novel composite film was fabricated by incorporating vegetable-tanned collagen fiber (VCF), a mechanically ground powder-like leather waste, into a chitosan matrix and crosslinked with genipin. The obtained composite film showed a compact structure and the hydrogen bonding interactions were confirmed by FTIR analysis, indicating a good compatibility between chitosan and VCF. The optical properties, water absorption capacity, thermal stability, water vapor permeability and mechanical properties of the composite films were characterized. The incorporation of VCF into chitosan led to significant decreases in opacity and solubility of the films. At the same time, the mechanical properties, water vapor permeability and thermal stability of the films were improved. The composite film exhibited antibacterial activity against food-borne pathogens. Results from this research indicated the potential of the genipin-crosslinked chitosan/VCF composites for applications in antimicrobial packaging. 

scholarly journals Preparation and Characterization of Edible Dialdehyde Carboxymethyl Cellulose Crosslinked Feather Keratin Films for Food Packaging

Polymers ◽  
2020 ◽  
Vol 12 (1) ◽  
pp. 158
Author(s):  
Yao Dou ◽  
Liguang Zhang ◽  
Buning Zhang ◽  
Ming He ◽  
Weimei Shi ◽  
...  
Keyword(s):  
Water Vapor ◽  
Carboxymethyl Cellulose ◽  
Food Packaging ◽  
Light Transmission ◽  
Value Added ◽  
Water Vapor Permeability ◽  
Barrier Properties ◽  
Edible Films ◽  
Vapor Permeability ◽  
Feather Keratin

The development of edible films based on the natural biopolymer feather keratin (FK) from poultry feathers is of great interest to food packaging. Edible dialdehyde carboxymethyl cellulose (DCMC) crosslinked FK films plasticized with glycerol were prepared by a casting method. The effect of DCMC crosslinking on the microstructure, light transmission, aggregate structure, tensile properties, water resistance and water vapor barrier were investigated. The results indicated the formation of both covalent and hydrogen bonding between FK and DCMC to form amorphous FK/DCMC films with good UV-barrier properties and transmittance. However, with increasing DCMC content, a decrease in tensile strength of the FK films indicated that plasticization, induced by hydrophilic properties of the DCMC, partly offset the crosslinking effect. Reduction in the moisture content, solubility and water vapor permeability indicated that DCMC crosslinking slightly reduced the moisture sensitivity of the FK films. Thus, DCMC crosslinking increased the potential viability of the FK films for food packaging applications, offering a value-added product.

scholarly journals Elaboration and Characterization of Active Apple Starch Films Incorporated with Ellagic Acid

Coatings ◽  
2018 ◽  
Vol 8 (11) ◽  
pp. 384
Author(s):  
Juan Tirado-Gallegos ◽  
Paul Zamudio-Flores ◽  
José Ornelas-Paz ◽  
Claudio Rios-Velasco ◽  
Guadalupe Olivas Orozco ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Water Vapor ◽  
Antioxidant Capacity ◽  
Ellagic Acid ◽  
Uv Light ◽  
Water Vapor Permeability ◽  
Vapor Permeability ◽  
Starch Films

Apple starch films were obtained from apples harvested at 60, 70, 80 and 90 days after full bloom (DAFB). Mechanical properties and water vapor permeability (WVP) were evaluated. The apple starch films at 70 DAFB presented higher values in the variables of tensile strength (8.12 MPa), elastic modulus (3.10 MPa) and lower values of water vapor permeability (6.77 × 10−11 g m−1 s−1 Pa−1) than apple starch films from apples harvested at 60, 80 and 90 DAFB. Therefore, these films were chosen to continue the study incorporating ellagic acid (EA). The EA was added at three concentrations [0.02% (FILM-EA0.02%), 0.05% (FILM-EA0.05%) and 0.1% (FILM-EA0.1%) w/w] and compared with the apple starch films without EA (FILM-Control). The films were characterized by their physicochemical, optical, morphological and mechanical properties. Their thermal stability and antioxidant capacity were also evaluated. The FILM-Control and FILM-EA0.02% showed a uniform surface, while FILM-EA0.05% and FILM-EA0.1% showed a rough surface and insoluble EA particles. Compared to FILM-Control, EA modified the values of tensile strength, elasticity modulus and elongation at break. The antioxidant capacity increased as EA concentration did. EA incorporation allowed obtaining films with higher antioxidant capacity, capable of blocking UV light with better mechanical properties than film without EA.

Physical Properties and Antimicrobial Activity of a Poly(Lactic Acid)/Poly(Trimethylene Carbonate) Film Incorporated with Thymol

2014 ◽  
Vol 884-885 ◽  
pp. 481-484 ◽  
Author(s):  
Yan Wu ◽  
Ming Wei Yuan ◽  
Ji Yi Yang ◽  
Yu Yue Qin ◽  
Ming Long Yuan ◽  
...  
Keyword(s):  
Antimicrobial Activity ◽  
Lactic Acid ◽  
Water Vapor ◽  
Composite Film ◽  
Food Packaging ◽  
Water Vapor Permeability ◽  
Antimicrobial Activities ◽  
Poly Lactic Acid ◽  
Vapor Permeability ◽  
Trimethylene Carbonate

Thymol (TH), which has antimicrobial effect on many food pathogens, was incorporated as antimicrobial agent into composite poly (lactic acid)/poly (trimethylene carbonate)(PLA-PTMC) films. Antimicrobial active films based on PLA-PTMC were prepared by incorporating thymol at five different concentrations: 0, 3, 6, 9 and 12 %(w/w). The mechanical characterization, water vapor permeability (WVP), and antimicrobial activity of all formulations composite film were carried out. A decrease in elastic modulus was obtained for the active composite film compared with neat PLA-PTMC film. The presence of thymol decreased water vapor permeability, with a significant antimicrobial activity. Antimicrobial activities of films were tested against Escherichia coli, Staphylococcus aurous, Listeria, Bacillus subtilis, and Salmonella. Increasing amount of the thymol in the film caused a significant increase in inhibitory zones. These results suggest that thymol incorporated PLA-PTMC films have a prospectively potential in antimicrobial food packaging.

Sign in / Sign up

Export Citation Format

Share Document