scholarly journals Cross-Linking and Evaluation of the Thermo-Mechanical Behavior of Epoxy Based Poly(ionic Liquid) Thermosets

Polymers ◽  
2021 ◽  
Vol 13 (22) ◽  
pp. 3914
Author(s):  
Florian Wanghofer ◽  
Archim Wolfberger ◽  
Markus Wolfahrt ◽  
Sandra Schlögl
Keyword(s):  
Mechanical Analysis ◽  
Thermomechanical Properties ◽  
Diglycidyl Ether ◽  
Scanning Calorimetry ◽  
Vast Number ◽  
Separation Membranes ◽  
Ionic Groups ◽  
Gas Separation Membranes ◽  
Poly Ionic Liquid ◽  
Selection Of

Poly(ionic liquids) (PILs) and ionenes are polymers containing ionic groups in their repeating units. The unique properties of these polymers render them as interesting candidates for a variety of applications, such as gas separation membranes and polyelectrolytes. Due to the vast number of possible structures, numerous synthesis protocols to produce monomers with different functional groups for task-specific PILs are reported in literature. A difunctional epoxy-IL resin was synthesized and cured with multifunctional amine and anhydride hardeners and the thermal and thermomechanical properties of the networks were assessed via differential scanning calorimetry and dynamic mechanical analysis. By the selection of suitable hardeners, the glass transition onset temperature (Tg,onset) of the resulting networks was varied between 18 °C and 99 °C. Copolymerization of epoxy-IL with diglycidyl ether of bisphenol A (DGEBA) led to a further increase of the Tg,onset. The results demonstrate the potential of epoxy chemistry for tailorable PIL networks, where the hardener takes the place of the ligands without requiring an additional synthesis step and can be chosen from a broad range of commercially available compounds.

scholarly journals Influence of 1D and 2D Carbon Fillers and Their Functionalisation on Crystallisation and Thermomechanical Properties of Injection Moulded Nylon 6,6 Nanocomposites

2014 ◽  
Vol 2014 ◽  
pp. 1-13 ◽  
Author(s):  
Fabiola Navarro-Pardo ◽  
Ana L. Martínez-Hernández ◽  
Victor M. Castaño ◽  
José L. Rivera-Armenta ◽  
Francisco J. Medellín-Rodríguez ◽  
...  
Keyword(s):  
Mechanical Analysis ◽  
Thermomechanical Properties ◽  
Reduced Form ◽  
Scanning Calorimetry ◽  
Graphene Nanocomposites ◽  
Moulding Process ◽  
Nylon 6,6 ◽  
Injection Moulding Process ◽  
The One ◽  
Carbon Fillers

Carbon nanotubes (CNTs) and graphene were used as reinforcing fillers in nylon 6,6 in order to obtain nanocomposites by using an injection moulding process. The two differently structured nanofillers were used in their pristine or reduced form, after oxidation treatment and after amino functionalisation. Three low nanofiller contents were employed. Crystallisation behaviour and perfection of nylon 6,6 crystals were determined by differential scanning calorimetry and wide angle X-ray diffraction, respectively. Crystallinity was slightly enhanced in most samples as the content of the nanofillers was increased. The dimensionality of the materials was found to provide different interfaces and therefore different features in the nylon 6,6 crystal growth resulting in improved crystal perfection. Dynamical, mechanical analysis showed the maximum increases provided by the two nanostructures correspond to the addition of 0.1 wt.% amino functionalised CNTs, enhancing in 30% the storage modulus and the incorporation of 0.5 wt.% of graphene oxide caused an increase of 44% in this property. The latter also provided better thermal stability when compared to pure nylon 6,6 under inert conditions. The superior properties of graphene nanocomposites were attributed to the larger surface area of the two-dimensional graphene compared to the one-dimensional CNTs.

scholarly journals The Effect of POSS Type on the Shape Memory Properties of Epoxy-Based Nanocomposites

Molecules ◽  
2020 ◽  
Vol 25 (18) ◽  
pp. 4203
Author(s):  
Avraham I. Bram ◽  
Irina Gouzman ◽  
Asaf Bolker ◽  
Noam Eliaz ◽  
Ronen Verker
Keyword(s):  
Transition Temperature ◽  
Shape Memory ◽  
Crosslinking Density ◽  
Mechanical Analysis ◽  
Thermomechanical Properties ◽  
Space Environment ◽  
Scanning Calorimetry ◽  
Space Applications ◽  
Curing Conditions ◽  
Oligomeric Silsesquioxane

Thermally activated shape memory polymers (SMPs) can memorize a temporary shape at low temperature and return to their permanent shape at higher temperature. These materials can be used for light and compact space deployment mechanisms. The control of transition temperature and thermomechanical properties of epoxy-based SMPs can be done using functionalized polyhedral oligomeric silsesquioxane (POSS) additives, which are also known to improve the durability to atomic oxygen in the space environment. In this study, the influence of varying amounts of two types of POSS added to epoxy-based SMPs on the shape memory effect (SME) were studied. The first type contained amine groups, whereas the second type contained epoxide groups. The curing conditions were defined using differential scanning calorimetry and glass transition temperature (Tg) measurements. Thermomechanical and SME properties were characterized using dynamic mechanical analysis. It was found that SMPs containing amine-based POSS show higher Tg, better shape fixity and faster recovery speed, while SMPs containing epoxide-based POSS have higher crosslinking density and show superior thermomechanical properties above Tg. This work demonstrates how the Tg and SME of SMPs can be controlled by the type and amount of POSS in an epoxy-based SMP nanocomposite for future space applications.

scholarly journals Bio-Based Epoxy Shape-Memory Thermosets from Triglycidyl Phloroglucinol

Polymers ◽  
2020 ◽  
Vol 12 (3) ◽  
pp. 542 ◽  
Author(s):  
David Santiago ◽  
Dailyn Guzmán ◽  
Francesc Ferrando ◽  
Àngels Serra ◽  
Silvia De la Flor
Keyword(s):  
Shape Memory ◽  
Shape Recovery ◽  
Memory Performance ◽  
Crosslinking Agent ◽  
Shape Memory Polymers ◽  
Crosslinking Density ◽  
Mechanical Analysis ◽  
Diglycidyl Ether ◽  
Partial Substitution ◽  
Scanning Calorimetry

A series of bio-based epoxy shape-memory thermosetting polymers were synthesized starting from a triglycidyl phloroglucinol (3EPOPh) and trimethylolpropane triglycidyl ether (TPTE) as epoxy monomers and a polyetheramine (JEF) as crosslinking agent. The evolution of the curing process was studied by differential scanning calorimetry (DSC) and the materials obtained were characterized by means of DSC, thermogravimetric analysis (TGA), dynamic mechanical analysis (DMA), stress-strain tests, and microindentation. Shape-memory properties were evaluated under free and totally constrained conditions. All results were compared with an industrial epoxy thermoset prepared from standard diglycidyl ether of Bisphenol A (DGEBA). Results revealed that materials prepared from 3EPOPh were more reactive and showed a tighter network with higher crosslinking density and glass transition temperatures than the prepared from DGEBA. The partial substitution of 3EPOPh by TPTE as epoxy comonomer caused an increase in the molecular mobility of the materials but without worsening the thermal stability. The shape-memory polymers (SMPs) prepared from 3EPOPh showed good mechanical properties as well as an excellent shape-memory performance. They showed almost complete shape-recovery and shape-fixation, fast shape-recovery rates, and recovery stress up to 7 MPa. The results obtained in this study allow us to conclude that the triglycidyl phloroglucinol derivative of eugenol is a safe and environmentally friendly alternative to DGEBA for preparing thermosetting shape-memory polymers.

Thermal and Thermomechanical Properties of Poly(butylene succinate) Nanocomposites

2008 ◽  
Vol 8 (4) ◽  
pp. 1679-1689 ◽  
Author(s):  
Mamookho E. Makhatha ◽  
Suprakas Sinha Ray ◽  
Joseph Hato ◽  
Adriaan S. Luyt
Keyword(s):  
Thermal Stability ◽  
Tensile Modulus ◽  
Melting Behavior ◽  
Mechanical Analysis ◽  
Thermomechanical Properties ◽  
Scanning Calorimetry ◽  
Melt Mixing ◽  
Butylene Succinate ◽  
Modulated Differential Scanning Calorimetry ◽  
Thermal Stability Of

This article describes the thermal and thermomechanical properties of poly(butylene succinate) (PBS) and its nanocomposites. PBS nanocomposites with three different weight ratios of organically modified synthetic fluorine mica (OMSFM) have been prepared by melt-mixing in a batch mixer at 140 °C. The structure and morphology of the nanocomposites were characterized by X-ray diffraction (XRD) analyses and transmission electron microscopy (TEM) observations that reveal the homogeneous dispersion of the intercalated silicate layers into the PBS matrix. The thermal properties of pure PBS and the nanocomposite samples were studied by both conventional and temperature modulated differential scanning calorimetry (DSC) analyses, which show multiple melting behavior of the PBS matrix. The investigation of the thermomechanical properties was performed by dynamic mechanical analysis. Results reveal significant improvement in the storage modulus of neat PBS upon addition of OMSFM. The tensile modulus of neat PBS is also increased substantially with the addition of OMSFM, however, the strength at yield and elongation at break of neat PBS systematically decreases with the loading of OMSFM. The thermal stability of the nanocomposites compared to that of the pure polymer sample was examined under both pyrolytic and thermooxidative environments. It is shown that the thermal stability of PBS is increased moderately in the presence of 3 wt% of OMSFM, but there is no significant effect on further silicate loading in the oxidative environment. In the nitrogen environment, however, the thermal stability systematically decreases with increasing clay loading.

Thermomechanical Characterization of Bismuth Telluride Based Thermoelectric Materials

2001 ◽  
Vol 691 ◽  
Author(s):  
Witold Brostow ◽  
Kevin P. Menard ◽  
John B. White
Keyword(s):  
Bismuth Telluride ◽  
Van Der Waals ◽  
Mechanical Analysis ◽  
Thermomechanical Properties ◽  
Thermal Transitions ◽  
Scanning Calorimetry ◽  
Direction Parallel ◽  
Crystalline Polymers ◽  
Structural Metals ◽  
P Type

ABSTRACTThe thermoelectric properties of bismuth telluride based thermoelectric (TE) materials are well-characterized, but comparatively little has been published on the mechanical and thermomechanical properties of these materials. In this paper, we present the initial dynamic mechanical analysis (DMA) data for n-type and p-type bismuth telluride based TE materials. The materials' tan δ values, indicative of viscoelastic energy dissipation modes, approach that of glassy or crystalline polymers and are greater than ten times the tan delta of structural metals. TE samples measured perpendicular to the van der Waals planes have higher tan δ values. Thermal scans in the DMA compressive mode showed changes in mechanical properties versus temperature with clear hysteresis effects. These changes were correlated to differential scanning calorimetry (DSC) thermal transitions. The expected anisotropy was shown in flexural 3-point bending results for one n-type material that showed a storage modulus of 0.10 to 0.45 GPa in the direction parallel to the van der Waals planes and 0.07 to 0.2 GPa in the perpendicular direction.

Application of dynamic mechanical analysis techniques to bismuth telluride based thermoelectric materials

e-Polymers ◽  
2004 ◽  
Vol 4 (1) ◽  
Author(s):  
Witold Brostow ◽  
Kevin P. Menard ◽  
John B. White
Keyword(s):  
Dynamic Mechanical Analysis ◽  
Bismuth Telluride ◽  
Polymeric Materials ◽  
Mechanical Analysis ◽  
Thermomechanical Properties ◽  
Thermal Transitions ◽  
Scanning Calorimetry ◽  
Dynamic Mechanical ◽  
Tan Δ ◽  
Te Material

Abstract Dynamic mechanical analysis (DMA) techniques are commonly applied to characterize polymer-based materials - but little if at all to characterize semiconductor thermoelectric (TE) materials. TE materials may be coupled with polymeric materials in advanced thermoelectric devices, and the knowledge of TE material properties will be useful in the choice of materials for future applications. We have obtained DMA results for both n-type and p-type bismuth telluride based TE materials. We find that tan δ values, indicative of viscoelastic energy dissipation modes, approach the values for glassy or semi-crystalline polymers, and are larger by more than a whole order of magnitude than the tan δ of structural metals. DMA thermal scans show clear hysteresis-type effects and a correlation with differential scanning calorimetry thermal transitions. DMA properties as a function of frequency are briefly discussed. Our results show that DMA techniques are useful in the evaluation of thermophysical and thermomechanical properties of these TE materials and of assembled coolers. The viscoelastic effects we report may provide a damping mechanism for severe stresses inherent to service conditions of the TE coolers.

scholarly journals The Influence of the Furan and Maleimide Stoichiometry on the Thermoreversible Diels–Alder Network Polymerization

Polymers ◽  
2021 ◽  
Vol 13 (15) ◽  
pp. 2522
Author(s):  
Ali Safaei ◽  
Seppe Terryn ◽  
Bram Vanderborght ◽  
Guy Van Assche ◽  
Joost Brancart
Keyword(s):  
Transition Temperature ◽  
Functional Groups ◽  
Polymer Networks ◽  
Viscoelastic Behavior ◽  
Mechanical Analysis ◽  
Thermomechanical Properties ◽  
Diels Alder ◽  
Stoichiometric Ratio ◽  
Self Healing ◽  
Scanning Calorimetry

In recent work, the thermoreversible Diels–Alder reaction between furan and maleimide functional groups has been studied extensively in the context of self-healing elastomers and thermosets. To elaborate the influence of the stoichiometric ratio between the maleimide and furan reactive groups on the thermomechanical properties and viscoelastic behavior of formed reversible covalent polymer networks, a series of Diels–Alder-based networks with different stoichiometric ratios was synthesized. Differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA) and dynamic rheology measurements were performed on the reversible polymer networks, to relate the reversible network structure to the material properties and reactivity. Such knowledge allows the design and optimization of the thermomechanical behavior of the reversible networks for intended applications. Lowering the maleimide-to-furan ratio creates a deficit of maleimide functional groups, resulting in a decrease in the crosslink density of the system, and a consequent decrease in the glass transition temperature, Young’s modulus, and gel transition temperature. The excess of unreacted furan in the system results in faster reaction and healing kinetics and a shift of the reaction equilibrium.

Calorimetric and Thermomechanical Properties of Titanium-Based Orthodontic Wires: DSC–DMA Relationship to Predict the Elastic Modulus

2011 ◽  
Vol 26 (7) ◽  
pp. 829-844 ◽  
Author(s):  
Giuliana Laino ◽  
Roberto De Santis ◽  
Antonio Gloria ◽  
Teresa Russo ◽  
David Suárez Quintanilla ◽  
...  
Keyword(s):  
Elastic Modulus ◽  
Young’S Modulus ◽  
Mechanical Performance ◽  
Young's Modulus ◽  
Experimental Tests ◽  
Mechanical Analysis ◽  
Thermomechanical Properties ◽  
Scanning Calorimetry ◽  
Orthodontic Wires ◽  
Gum Metal

Orthodontic treatment is strongly dependent on the loads developed by metal wires, and the choice of an orthodontic archwire should be based on its mechanical performance. The desire of both orthodontists and engineers would be to predict the mechanical behavior of archwires. To this aim, Gum Metal (Toyota Central R&L Labs., Inc.), TMA (ORMCO), 35°C Copper NiTi (SDS ORMCO), Thermalloy Plus (Rocky Mountain), Nitinol SE (3M Unitek), and NiTi (SDS ORMCO) were tested according to dynamic mechanical analysis and differential scanning calorimetry. A model was also developed to predict the elastic modulus of superelastic wires. Results from experimental tests have highlighted that superelastic wires are very sensitive to temperature variations occurring in the oral environment, while the proposed model seems to be reliable to predict the Young’s modulus allowing to correlate calorimetric and mechanical data. Furthermore, Gum Metal wire behaves as an elastic material with a very low Young’s modulus, and it can be particularly useful for the initial stage of orthodontic treatments.

scholarly journals Poly(etheretherketone)/Poly(ethersulfone) Blends with Phenolphthalein: Miscibility, Thermomechanical Properties, Crystallization and Morphology

Polymers ◽  
2021 ◽  
Vol 13 (9) ◽  
pp. 1466
Author(s):  
Adrian Korycki ◽  
Christian Garnier ◽  
Amandine Abadie ◽  
Valerie Nassiet ◽  
Charles Tarek Sultan ◽  
...  
Keyword(s):  
Differential Scanning Calorimetry ◽  
Interfacial Adhesion ◽  
Morphological Analysis ◽  
Condensation Reaction ◽  
Mechanical Analysis ◽  
Thermomechanical Properties ◽  
Glass Transitions ◽  
Scanning Calorimetry ◽  
Melt Mixing ◽  
Spherical Domains

Polyetheretherketone (PEEK)/polyethersulfone (PES) blends are initially not miscible, except when the blends are prepared by solvent mixing. We propose a route to elaborate PEEK/PES blends with partial miscibility by melt mixing at 375 °C with phenolphthalein. The miscibility of blends has been examined using differential scanning calorimetry (DSC) and dynamic mechanical analysis (DMTA). When adding phenolphthalein to PEEK/PES blends, the glass transitions are shifted inward as an indication of miscibility. We suggest that phenolphthalein acts as a compatibilizer by creating cardo side groups on PEEK and PES chains by nucleophilic substitution in the melted state, although this condensation reaction was reported only in the solvent until now. In addition, phenolphthalein acts as a plasticizer for PES by decreasing its glass transition. As a consequence, the PEEK phase is softened which favors the crystallization as the increase of crystalline rate. Due to aromatic moieties in phenolphthalein, the storage modulus of blends in the glassy region is kept identical to pure PEEK. The morphological analysis by SEM pictures displays nano- to microsized PES spherical domains in the PEEK matrix with improved PEEK/PES interfacial adhesion.

Dynamic Mechanical Properties of Epoxy Resin with Multifunctional Polyamine Curing Agent

2015 ◽  
Vol 744-746 ◽  
pp. 1374-1377
Author(s):  
Xi Wang
Keyword(s):  
Thermal Stability ◽  
Dynamic Mechanical Properties ◽  
Mechanical Analysis ◽  
Diglycidyl Ether ◽  
Curing Agent ◽  
Scanning Calorimetry ◽  
Good Thermal Stability ◽  
Dynamic Mechanical ◽  
Glass Relaxation ◽  
Thermal Stability Of

A nonlinear multifunctional polyamine N,N,N’,N’-tetra (3-aminopropyl)-1,6-diamino-hexane (TADH), was prepared and employed as a novel hardener for diglycidyl ether of bisphenol A (DGEBA). Nonisothermal reactions of DGEBA/TADH were systematically investigated with differential scanning calorimetry (DSC). In addition, analysis of thermal stability of the cured DGEBA/TADH with thermogravimetric analysis (TGA) revealed that it possessed quite good thermal stability and increased residual char content at 600◦C in nitrogen. Furthermore, dynamic mechanical analysis (DMA) of the DGEBA/TADH network showed its relaxations were characterized by localized motions of hydroxyl ether segments and cooperative motions of whole network chains (glass relaxation) at different temperature regions.

Sign in / Sign up

Export Citation Format

Share Document