scholarly journals Application of Amberlite IRA 402 Resin Adsorption and Laccase Treatment for Acid Blue 113 Removal from Aqueous Media

Polymers ◽  
2021 ◽  
Vol 13 (22) ◽  
pp. 3991
Author(s):  
Nicoleta Mirela Marin ◽  
Ioana Stanculescu

Despite Acid Blue 113 (AB 113)’s extensive use and negative environmental impact, very few studies have focused on its efficient and environmentally friendly removal. This research aims the removal of AB 113 from environmental aqueous media and its consequent enzymatic biodegradation. A strongly basic anion exchange resin in Cl− form, Amberlite IRA 402 (IRA 402(Cl−)) was used for AB 113 adsorption and a laccase was used to further biodegrade it. For the first time, two novel, efficient and environmentally friendly physical–chemical and biological assays for AB 113 wastewater removal and subsequent biodegradation were combined. The adsorption of AB 113 onto IRA 402(Cl−) was tested in batch and continuous flux modes. Influence of contact time, concentration and desorption in acidic media were evaluated. The kinetic data were best modulated by the Lagergren model with R2 = 0.9275. The Langmuir isotherm model best fitted the experimental data, and the maximum adsorption capacity was 130 mg/g. Dye, resin and AB113 loaded resin were characterized by thermogravimetry and FTIR to evaluate their physical chemical properties modification. Based on the performed studies, a consecutive methodology is proposed, incorporating the ion exchange process in the first stage and the biodegradation process in the second. Thus, in the second stage the residual concentration of AB 113 is reduced by an efficient bio-degradation process produced by the laccase at pH = 4.

2014 ◽  
Vol 938 ◽  
pp. 257-262
Author(s):  
G.A. Suganya Josephine ◽  
Arumugam Sivasamy

Dyes are a source of serious pollutants from different industrial outlets and show a major contribution in polluting the environment. In the present study two dyes namely Orange G and Acid Blue 113 were compared for their photodegradation efficiency employing rare earth nanometal oxide as a visible active photocatalyst. The prepared catalyst was nanocrystalline form with particle size 70 nm and the surface of the catalyst was highly porous and rough which facilitates the absorption of the dye further enhance the photo degradation which were confirmed by various characterization techniques. Effect of pH, variation of catalyst dosage, variation of initial dye concentration and kinetic studies were conducted for both the dyes. The reaction followed a pseudo first order kinetics. The activity of the prepared catalyst was higher when compared to a commercially used metal oxide. Reusability studies proved that the catalyst prepared was very active even upto the third cycle. The degradation process was initiated by the attack of the OH radical generated in the in-situ process via visible light irradiation. EPR spin trapping technique was employed to confirm the presence of OH radicals. The prepared catalyst degraded the dye molecules of interest in lesser time duration by absorption of visible light, thereby reducing the cost of photodegradation.


1986 ◽  
Vol 21 (3) ◽  
pp. 344-350 ◽  
Author(s):  
Barry G. Oliver ◽  
Klaus L.E. Kaiser

Abstract The concent rat ions of hexachloroethane (HCE), hexachlorobutadiene (HCBD), pentachlorobenzene (QCB), hexachlorobenzene (HCB) and octachlorostyrene (OCS) in large volume water samples show that the major sources of these chemicals to the St. Clair River are Dow Chemical Company effluents and, to a lesser degree, Sarnia’s Township ditch which drains one of Dow’s waste disposal sites. Tributaries entering the river on both sides of the Canada/United States border contain measurable concentrations of these chemicals indicating low level contamination throughout the area. The degree of water/suspended sediment partitioning of the chemicals (Kp) was studied. Kp values for the individual chemicals changed in a manner consistent with changes in their physical-chemical properties.


2020 ◽  
Vol 16 ◽  
Author(s):  
Reda M. El-Shishtawy ◽  
Abdullah M. Asiri ◽  
Nahed S. E. Ahmed

Background: Color effluents generated from the production industry of dyes and pigments and their use in different applications such as textile, paper, leather tanning, and food industries, are high in color and contaminants that damage the aquatic life. It is estimated that about 105 of various commercial dyes and pigments amounted to 7×105 tons are produced annually worldwide. Ultimately, about 10–15% is wasted into the effluents of the textile industry. Chitin is abundant in nature, and it is a linear biopolymer containing acetamido and hydroxyl groups amenable to render it atmospheric by introducing amino and carboxyl groups, hence able to remove different classes of toxic organic dyes from colored effluents. Methods: Chitin was chemically modified to render it amphoteric via the introduction of carboxyl and amino groups. The amphoteric chitin has been fully characterized by FTIR, TGA-DTG, elemental analysis, SEM, and point of zero charge. Adsorption optimization for both anionic and cationic dyes was made by batch adsorption method, and the conditions obtained were used for studying the kinetics and thermodynamics of adsorption. Results: The results of dye removal proved that the adsorbent was proven effective in removing both anionic and cationic dyes (Acid Red 1 and methylene blue (MB)), at their respective optimum pHs (2 for acid and 8 for cationic dye). The equilibrium isotherm at room temperature fitted the Freundlich model for MB, and the maximum adsorption capacity was 98.2 mg/g using 50 mg/l of MB, whereas the equilibrium isotherm fitted the Freundlich and Langmuir model for AR1 and the maximum adsorption capacity was 128.2 mg/g. Kinetic results indicate that the adsorption is a two-step diffusion process for both dyes as indicated by the values of the initial adsorption factor (Ri) and follows the pseudo-second-order kinetics. Also, thermodynamic calculations suggest that the adsorption of AR1 on the amphoteric chitin is an endothermic process from 294 to 303 K. The result indicated that the mechanism of adsorption is chemisorption via an ion-exchange process. Also, recycling of the adsorbent was easy, and its reuse for dye removal was effective. Conclusion: New amphoteric chitin has been successfully synthesized and characterized. This resin material, which contains amino and carboxyl groups, is novel as such chemical modification of chitin hasn’t been reported. The amphoteric chitin has proven effective in decolorizing aqueous solution from anionic and cationic dyes. The adsorption behavior of amphoteric chitin is believed to follow chemical adsorption with an ion-exchange process. The recycling process for few cycles indicated that the loaded adsorbent could be regenerated by simple treatment and retested for removing anionic and cationic dyes without any loss in the adsorbability. Therefore, the study introduces a new and easy approach for the development of amphoteric adsorbent for application in the removal of different dyes from aqueous solutions.


2020 ◽  
Vol 20 (11) ◽  
pp. 1340-1351 ◽  
Author(s):  
Ponnurengam M. Sivakumar ◽  
Matin Islami ◽  
Ali Zarrabi ◽  
Arezoo Khosravi ◽  
Shohreh Peimanfard

Background and objective: Graphene-based nanomaterials have received increasing attention due to their unique physical-chemical properties including two-dimensional planar structure, large surface area, chemical and mechanical stability, superconductivity and good biocompatibility. On the other hand, graphene-based nanomaterials have been explored as theranostics agents, the combination of therapeutics and diagnostics. In recent years, grafting hydrophilic polymer moieties have been introduced as an efficient approach to improve the properties of graphene-based nanomaterials and obtain new nanoassemblies for cancer therapy. Methods and results: This review would illustrate biodistribution, cellular uptake and toxicity of polymergraphene nanoassemblies and summarize part of successes achieved in cancer treatment using such nanoassemblies. Conclusion: The observations showed successful targeting functionality of the polymer-GO conjugations and demonstrated a reduction of the side effects of anti-cancer drugs for normal tissues.


2021 ◽  
Vol 11 (10) ◽  
pp. 4417
Author(s):  
Veronica Vendramin ◽  
Gaia Spinato ◽  
Simone Vincenzi

Chitosan is a chitin-derived fiber, extracted from the shellfish shells, a by-product of the fish industry, or from fungi grown in bioreactors. In oenology, it is used for the control of Brettanomyces spp., for the prevention of ferric, copper, and protein casse and for clarification. The International Organisation of Vine and Wine established the exclusive utilization of fungal chitosan to avoid the eventuality of allergic reactions. This work focuses on the differences between two chitosan categories, fungal and animal chitosan, characterizing several samples in terms of chitin content and degree of deacetylation. In addition, different acids were used to dissolve chitosans, and their effect on viscosity and on the efficacy in wine clarification were observed. The results demonstrated that even if fungal and animal chitosans shared similar chemical properties (deacetylation degree and chitin content), they showed different viscosity depending on their molecular weight but also on the acid used to dissolve them. A significant difference was discovered on their fining properties, as animal chitosans showed a faster and greater sedimentation compared to the fungal ones, independently from the acid used for their dissolution. This suggests that physical–chemical differences in the molecular structure occur between the two chitosan categories and that this significantly affects their technologic (oenological) properties.


2020 ◽  
Vol 59 (1) ◽  
pp. 441-454
Author(s):  
Carlos A. Martínez-Pérez

AbstractIn the last years, electrospinning has become a technique of intense research to design and fabricate drug delivery systems (DDS), during this time a vast variety of DDS with mainly electrospun polymers and many different active ingredient(s) have been developed, many intrinsic and extrinsic factor have influence in the final system, there are those that can be attributed to the equipment set up and that to the physical-chemical properties of the used materials in the fabrication of DDS. After all, this intense research has generated a great amount of DDS loaded with one or more drugs. In this manuscript a review with the highlights of different kind of systems for drug delivery systems is presented, it includes the basic concepts of electrospinning, types of equipment set up, polymer/drug systems, limitations and challenges that need to be overcome for clinical applications.


2021 ◽  
Vol 494 ◽  
pp. 119334
Author(s):  
Vinicius Evangelista Silva ◽  
Thiago Assis Rodrigues Nogueira ◽  
Cassio Hamilton Abreu-Junior ◽  
Arun Dilipkumar Jani ◽  
Salatier Buzetti ◽  
...  

Sign in / Sign up

Export Citation Format

Share Document