scholarly journals Force Pattern and Acceleration Waveform Repeatability of Amateur Runners

Proceedings ◽  
2020 ◽  
Vol 49 (1) ◽  
pp. 136
Author(s):  
Ophelie Lariviere ◽  
Thomas Provot ◽  
Laura Valdes-Tamayo ◽  
Maxime Bourgain ◽  
Delphine Chadefaux

Although accelerometers’ responses during running are not perfectly understood, they are widely used to study performance and the risk of injury. To outline the typical tibial acceleration pattern during running, this study aims to investigate the repeatability of acceleration signals with respect to the ground reaction force waveforms. Ten amateur runners were asked to perform ten trials along a straight line. One participant was asked to perform this protocol over ten sessions. Tibial accelerations and ground reaction forces were measured during the stance phase. The coefficient of multiple correlation R was computed to study the intra- and inter-test and subject repeatability of accelerometric and force waveforms. A good (R>0.8) intra- and inter-test repeatability was observed for all measured signals. Similar results were observed for intra-subject repeatability. A good inter-subject repeatability was observed only for the longitudinal acceleration and vertical and antero-posterior forces. Typical accelerometric signatures were outlined for each case studied.

2020 ◽  
Vol 2 (4) ◽  
pp. 287-304 ◽  
Author(s):  
Jason S. Pedley ◽  
Rhodri S. Lloyd ◽  
Paul J. Read ◽  
Isabel S. Moore ◽  
Mark De Ste Croix ◽  
...  

Abstract Purpose Jump-landing assessments provide a means to quantify an individual’s ability to attenuate ground reaction forces, generate lower limb explosive power and maintain joint alignment. In order to identify risk factors that can be targeted through appropriate training interventions, it is necessary to establish which (scalar) objective kinetic, kinematic, and performance measures are most associated with lower-extremity injury. Methods Online searches of MEDLINE, SCOPUS, EBSCOHost, SPORTDiscus and PubMed databases were completed for all articles published before March 2020 in accordance with PRISMA guidelines. Results 40 articles investigating nine jump-landing assessments were included in this review. The 79% of studies using drop jump (n = 14) observed an association with future injury, while only 8% of countermovement jump studies (n = 13) observed an association with injury risk. The 57% of studies using unilateral assessments found associations with risk of injury (n = 14). Studies using performance measures (jump height/distance) as outcome measure were only associated with injury risk in 30% of cases. However, those using kinetic and/or kinematic analyses (knee abduction moment, knee valgus angle, knee separation distance, peak ground reaction force) found associations with injury in 89% of studies. Conclusion The landing element of jump-landing assessments appears to be superior for identifying individuals at greater risk of injury; likely due to a closer representation of the injury mechanism. Consequently, jump-landing assessments that involve attenuation of impact forces such as the drop jump appear most suited for this purpose but should involve assessment of frontal plane knee motion and ground reaction forces.


2019 ◽  
Vol 126 (5) ◽  
pp. 1315-1325 ◽  
Author(s):  
Andrew B. Udofa ◽  
Kenneth P. Clark ◽  
Laurence J. Ryan ◽  
Peter G. Weyand

Although running shoes alter foot-ground reaction forces, particularly during impact, how they do so is incompletely understood. Here, we hypothesized that footwear effects on running ground reaction force-time patterns can be accurately predicted from the motion of two components of the body’s mass (mb): the contacting lower-limb (m1 = 0.08mb) and the remainder (m2 = 0.92mb). Simultaneous motion and vertical ground reaction force-time data were acquired at 1,000 Hz from eight uninstructed subjects running on a force-instrumented treadmill at 4.0 and 7.0 m/s under four footwear conditions: barefoot, minimal sole, thin sole, and thick sole. Vertical ground reaction force-time patterns were generated from the two-mass model using body mass and footfall-specific measures of contact time, aerial time, and lower-limb impact deceleration. Model force-time patterns generated using the empirical inputs acquired for each footfall matched the measured patterns closely across the four footwear conditions at both protocol speeds ( r2 = 0.96 ± 0.004; root mean squared error  = 0.17 ± 0.01 body-weight units; n = 275 total footfalls). Foot landing angles (θF) were inversely related to footwear thickness; more positive or plantar-flexed landing angles coincided with longer-impact durations and force-time patterns lacking distinct rising-edge force peaks. Our results support three conclusions: 1) running ground reaction force-time patterns across footwear conditions can be accurately predicted using our two-mass, two-impulse model, 2) impact forces, regardless of foot strike mechanics, can be accurately quantified from lower-limb motion and a fixed anatomical mass (0.08mb), and 3) runners maintain similar loading rates (ΔFvertical/Δtime) across footwear conditions by altering foot strike angle to regulate the duration of impact. NEW & NOTEWORTHY Here, we validate a two-mass, two-impulse model of running vertical ground reaction forces across four footwear thickness conditions (barefoot, minimal, thin, thick). Our model allows the impact portion of the impulse to be extracted from measured total ground reaction force-time patterns using motion data from the ankle. The gait adjustments observed across footwear conditions revealed that runners maintained similar loading rates across footwear conditions by altering foot strike angles to regulate the duration of impact.


Sensors ◽  
2019 ◽  
Vol 19 (9) ◽  
pp. 2011 ◽  
Author(s):  
Bessone ◽  
Petrat ◽  
Schwirtz

In the past, technological issues limited research focused on ski jump landing. Today, thanks to the development of wearable sensors, it is possible to analyze the biomechanics of athletes without interfering with their movements. The aims of this study were twofold. Firstly, the quantification of the kinetic magnitude during landing is performed using wireless force insoles while 22 athletes jumped during summer training on the hill. In the second part, the insoles were combined with inertial motion units (IMUs) to determine the possible correlation between kinematics and kinetics during landing. The maximal normal ground reaction force (GRFmax) ranged between 1.1 and 5.3 body weight per foot independently when landing using the telemark or parallel leg technique. The GRFmax and impulse were correlated with flying time (p < 0.001). The hip flexions/extensions and the knee and hip rotations of the telemark front leg correlated with GRFmax (r = 0.689, p = 0.040; r = −0.670, p = 0.048; r = 0.820, p = 0.007; respectively). The force insoles and their combination with IMUs resulted in promising setups to analyze landing biomechanics and to provide in-field feedback to the athletes, being quick to place and light, without limiting movement.


2006 ◽  
Vol 3 (4) ◽  
pp. 209-216 ◽  
Author(s):  
Pia Gustås ◽  
Christopher Johnston ◽  
Stig Drevemo

AbstractThe objective of the present study was to compare the hoof deceleration and ground reaction forces following impact on two different surfaces. Seven unshod Standardbreds were trotted by hand at 3.0–5.7 m s− 1 over a force plate covered by either of the two surfaces, sandpaper or a 1 cm layer of sand. Impact deceleration data were recorded from one triaxial accelerometer mounted on the fore- and hind hooves, respectively. Ground reaction force data were obtained synchronously from a force plate, sampled at 4.8 kHz. The differences between the two surfaces were studied by analysing representative deceleration and force variables for individual horses. The maximum horizontal peak deceleration and the loading rates of the vertical and the horizontal forces were significantly higher on sandpaper compared with the sand surface (P < 0.001). In addition, the initial vertical deceleration was significantly higher on sandpaper in the forelimb (P < 0.001). In conclusion, it was shown that the different qualities of the ground surface result in differences in the hoof-braking pattern, which may be of great importance for the strength of the distal horse limb also at slow speeds.


2007 ◽  
Vol 23 (3) ◽  
pp. 180-189 ◽  
Author(s):  
Niell G. Elvin ◽  
Alex A. Elvin ◽  
Steven P. Arnoczky

Modern electronics allow for the unobtrusive measurement of accelerations outside the laboratory using wireless sensor nodes. The ability to accurately measure joint accelerations under unrestricted conditions, and to correlate them with jump height and landing force, could provide important data to better understand joint mechanics subject to real-life conditions. This study investigates the correlation between peak vertical ground reaction forces, as measured by a force plate, and tibial axial accelerations during free vertical jumping. The jump heights calculated from force-plate data and accelerometer measurements are also compared. For six male subjects participating in this study, the average coefficient of determination between peak ground reaction force and peak tibial axial acceleration is found to be 0.81. The coefficient of determination between jump height calculated using force plate and accelerometer data is 0.88. Data show that the landing forces could be as high as 8 body weights of the jumper. The measured peak tibial accelerations ranged up to 42 g. Jump heights calculated from force plate and accelerometer sensors data differed by less than 2.5 cm. It is found that both impact accelerations and landing forces are only weakly correlated with jump height (the average coefficient of determination is 0.12). This study shows that unobtrusive accelerometers can be used to determine the ground reaction forces experienced in a jump landing. Whereas the device also permitted an accurate determination of jump height, there was no correlation between peak ground reaction force and jump height.


2011 ◽  
Vol 133 (5) ◽  
Author(s):  
Lyle T. Jackson ◽  
Patrick M. Aubin ◽  
Matthew S. Cowley ◽  
Bruce J. Sangeorzan ◽  
William R. Ledoux

The symptomatic flatfoot deformity (pes planus with peri-talar subluxation) can be a debilitating condition. Cadaveric flatfoot models have been employed to study the etiology of the deformity, as well as invasive and noninvasive surgical treatment strategies, by evaluating bone positions. Prior cadaveric flatfoot simulators, however, have not leveraged industrial robotic technologies, which provide several advantages as compared with the previously developed custom fabricated devices. Utilizing a robotic device allows the researcher to experimentally evaluate the flatfoot model at many static instants in the gait cycle, compared with most studies, which model only one to a maximum of three instances. Furthermore, the cadaveric tibia can be statically positioned with more degrees of freedom and with a greater accuracy, and then a custom device typically allows. We created a six degree of freedom robotic cadaveric simulator and used it with a flatfoot model to quantify static bone positions at ten discrete instants over the stance phase of gait. In vivo tibial gait kinematics and ground reaction forces were averaged from ten flatfoot subjects. A fresh frozen cadaveric lower limb was dissected and mounted in the robotic gait simulator (RGS). Biomechanically realistic extrinsic tendon forces, tibial kinematics, and vertical ground reaction forces were applied to the limb. In vitro bone angular position of the tibia, calcaneus, talus, navicular, medial cuneiform, and first metatarsal were recorded between 0% and 90% of stance phase at discrete 10% increments using a retroreflective six-camera motion analysis system. The foot was conditioned flat through ligament attenuation and axial cyclic loading. Post-flat testing was repeated to study the pes planus deformity. Comparison was then made between the pre-flat and post-flat conditions. The RGS was able to recreate ten gait positions of the in vivo pes planus subjects in static increments. The in vitro vertical ground reaction force was within ±1 standard deviation (SD) of the in vivo data. The in vitro sagittal, coronal, and transverse plane tibial kinematics were almost entirely within ±1 SD of the in vivo data. The model showed changes consistent with the flexible flatfoot pathology including the collapse of the medial arch and abduction of the forefoot, despite unexpected hindfoot inversion. Unlike previous static flatfoot models that use simplified tibial degrees of freedom to characterize only the midpoint of the stance phase or at most three gait positions, our simulator represented the stance phase of gait with ten discrete positions and with six tibial degrees of freedom. This system has the potential to replicate foot function to permit both noninvasive and surgical treatment evaluations throughout the stance phase of gait, perhaps eliciting unknown advantages or disadvantages of these treatments at other points in the gait cycle.


1986 ◽  
Vol 15 (1) ◽  
pp. 27-34 ◽  
Author(s):  
R Seliktar ◽  
J Mizrahi

Human locomotion studies employing cinematography and force plates have been conducted during the last five decades with the goal of producing a clinically acceptable gait evaluation technique. The bulk of information contained in the kinetic studies was the major obstacle in achieving this goal. Our aim in this work was to explore the possibility of representing some locomotor abnormalities solely by their reflection on the ground reaction force characteristics. As a first stage towards the establishment of these relationships, the gait characteristics of below-knee amputees were examined. One hundred and thirty ground force test results as obtained on twenty three below-knee amputees were analysed. Different variables such as time durations of the various phases, peak forces, impulses, rate of change of the forces, and others, were examined. The conclusions suggest that some of these variables are suitable for evaluation of gait and some, such as small perturbations superimposed on the curve, may serve as indicators of specific malfunction of the prosthetic system.


2019 ◽  
Vol 14 (5) ◽  
pp. 658-666 ◽  
Author(s):  
Steffi L Colyer ◽  
Philip Graham-Smith ◽  
Aki IT Salo

Ground reaction forces produced on the blocks determine an athlete’s centre of mass motion during the sprint start, which is crucial to sprint performance. This study aimed to understand how force waveforms are associated with better sprint start performance. Fifty-seven sprinters (from junior to world elite) performed a series of block starts during which the ground reaction forces produced by the legs and arms were separately measured. Statistical parametric mapping (linear regression) revealed specific phases of these waveforms where forces were associated with average horizontal external power. Better performances were achieved by producing higher forces and directing the force vector more horizontally during the initial parts of the block phase (17–34% and 5–37%, respectively). During the mid-push (around the time of rear block exit: ∼54% of the block push), magnitudes of front block force differentiated performers, but orientation did not. Consequently, the ability to sustain high forces during the transition from bilateral to unilateral pushing was a performance-differentiating factor. Better athletes also exhibited a higher ratio of forces on the front block in the latter parts of unilateral pushing (81–92% of the block push), which seemed to allow these athletes to exit the blocks with lower centre of mass projection angles. Training should reflect these kinetic requirements, but also include technique-based aspects to increase both force production and orientation capacities. Specific training focused on enhancing anteroposterior force production during the transition between double- to single-leg propulsion could be beneficial for overall sprint start performance.


Author(s):  
Ritwik Rakshit ◽  
Yujiang Xiang ◽  
James Yang

This article presents an optimization formulation and experimental validation of a dynamic-joint-strength-based two-dimensional symmetric maximum weight-lifting simulation. Dynamic joint strength (the net moment capacity as a function of joint angle and angular velocity), as presented in the literature, is adopted in the optimization formulation to predict the symmetric maximum lifting weight and corresponding motion. Nineteen participants were recruited to perform a maximum-weight-box-lifting task in the laboratory, and kinetic and kinematic data including motion and ground reaction forces were collected using a motion capture system and force plates, respectively. For each individual, the predicted spine, shoulder, elbow, hip, knee, and ankle joint angles, as well as vertical and horizontal ground reaction force and box weight, were compared with the experimental data. Both root-mean-square error and Pearson’s correlation coefficient ( r) were used for the validation. The results show that the proposed two-dimensional optimization-based motion prediction formulation is able to accurately predict all joint angles, box weights, and vertical ground reaction forces, but not horizontal ground reaction forces.


Sign in / Sign up

Export Citation Format

Share Document