scholarly journals Selective Functionalization of High-Resolution Cu2O Nanopatterns via Galvanic Replacement for Highly Enhanced Gas Sensing Performance

Sensors ◽  
2018 ◽  
Vol 18 (12) ◽  
pp. 4438 ◽  
Author(s):  
Ju Kim ◽  
Soo-Yeon Cho ◽  
Hee-Tae Jung
Keyword(s):  
High Resolution ◽  
Metal Ion ◽  
Gas Sensing ◽  
High Surface ◽  
Volume Ratio ◽  
Energy Difference ◽  
Galvanic Replacement ◽  
Selective Functionalization ◽  
Nanochannel Array ◽  
Sensing Performance

Recently, high-resolution patterned metal oxide semiconductors (MOS) have gained considerable attention for enhanced gas sensing performance due to their polycrystalline nature, ultrasmall grain size (~5 nm), patternable properties, and high surface-to-volume ratio. Herein, we significantly enhanced the sensing performance of that patterned MOS by galvanic replacement, which allows for selective functionalization on ultrathin Cu2O nanopatterns. Based on the reduction potential energy difference between the base channel material (Cu2O) and the decorated metal ion (Pt2+), Pt could be selectively and precisely decorated onto the desired area of the Cu2O nanochannel array. Overall, the Pt-decorated Cu2O exhibited 11-fold higher NO2 (100 ppm) sensing sensitivity as compared to the non-decorated sensing channel, the while the channel device with excessive Pt doping showed complete loss of sensing properties.

scholarly journals Three-dimensional platinum nanoparticle-based bridges for ammonia gas sensing

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Nishchay A. Isaac ◽  
Johannes Reiprich ◽  
Leslie Schlag ◽  
Pedro H. O. Moreira ◽  
Mostafa Baloochi ◽  
...  
Keyword(s):  
Room Temperature ◽  
Gas Sensing ◽  
Response Times ◽  
High Surface ◽  
Three Dimensional ◽  
Performance Testing ◽  
Volume Ratio ◽  
Platinum Nanoparticle ◽  
Ammonia Gas ◽  
Lift Off

AbstractThis study demonstrates the fabrication of self-aligning three-dimensional (3D) platinum bridges for ammonia gas sensing using gas-phase electrodeposition. This deposition scheme can guide charged nanoparticles to predetermined locations on a surface with sub-micrometer resolution. A shutter-free deposition is possible, preventing the use of additional steps for lift-off and improving material yield. This method uses a spark discharge-based platinum nanoparticle source in combination with sequentially biased surface electrodes and charged photoresist patterns on a glass substrate. In this way, the parallel growth of multiple sensing nodes, in this case 3D self-aligning nanoparticle-based bridges, is accomplished. An array containing 360 locally grown bridges made out of 5 nm platinum nanoparticles is fabricated. The high surface-to-volume ratio of the 3D bridge morphology enables fast response and room temperature operated sensing capabilities. The bridges are preconditioned for ~ 24 h in nitrogen gas before being used for performance testing, ensuring drift-free sensor performance. In this study, platinum bridges are demonstrated to detect ammonia (NH3) with concentrations between 1400 and 100 ppm. The sensing mechanism, response times, cross-sensitivity, selectivity, and sensor stability are discussed. The device showed a sensor response of ~ 4% at 100 ppm NH3 with a 70% response time of 8 min at room temperature.

scholarly journals A Review of Carbon Nanotubes-Based Gas Sensors

2009 ◽  
Vol 2009 ◽  
pp. 1-24 ◽  
Author(s):  
Yun Wang ◽  
John T. W. Yeow
Keyword(s):  
Carbon Nanotubes ◽  
Gas Sensors ◽  
Gas Sensing ◽  
Low Cost ◽  
High Surface ◽  
Hollow Structure ◽  
Volume Ratio ◽  
Fast Response ◽  
Sensing Technology ◽  
Structure Of Nanomaterials

Gas sensors have attracted intensive research interest due to the demand of sensitive, fast response, and stable sensors for industry, environmental monitoring, biomedicine, and so forth. The development of nanotechnology has created huge potential to build highly sensitive, low cost, portable sensors with low power consumption. The extremely high surface-to-volume ratio and hollow structure of nanomaterials is ideal for the adsorption of gas molecules. Particularly, the advent of carbon nanotubes (CNTs) has fuelled the inventions of gas sensors that exploit CNTs' unique geometry, morphology, and material properties. Upon exposure to certain gases, the changes in CNTs' properties can be detected by various methods. Therefore, CNTs-based gas sensors and their mechanisms have been widely studied recently. In this paper, a broad but yet in-depth survey of current CNTs-based gas sensing technology is presented. Both experimental works and theoretical simulations are reviewed. The design, fabrication, and the sensing mechanisms of the CNTs-based gas sensors are discussed. The challenges and perspectives of the research are also addressed in this review.

Nanomaterial-based gas sensors used for breath diagnosis

2020 ◽  
Vol 8 (16) ◽  
pp. 3231-3248 ◽  
Author(s):  
Xinyuan Zhou ◽  
Zhenjie Xue ◽  
Xiangyu Chen ◽  
Chuanhui Huang ◽  
Wanqiao Bai ◽  
...  
Keyword(s):  
Physicochemical Properties ◽  
Gas Sensors ◽  
Active Sites ◽  
Gas Sensing ◽  
High Surface ◽  
Volume Ratio ◽  
Sensing Applications ◽  
Enormous Number

Gas-sensing applications commonly use nanomaterials (NMs) because of their unique physicochemical properties, including a high surface-to-volume ratio, enormous number of active sites, controllable morphology, and potential for miniaturisation.

Analytical modeling of phosphorene-based NO2 gas sensor

2019 ◽  
Vol 33 (14) ◽  
pp. 1950143 ◽  
Author(s):  
Elham Mansouri ◽  
Javad Karamdel ◽  
Mohammad Taghi Ahmadi ◽  
Masoud Berahman
Keyword(s):  
Gas Sensor ◽  
Carrier Mobility ◽  
Analytical Modeling ◽  
Gas Sensing ◽  
High Surface ◽  
Volume Ratio ◽  
Gas Concentration ◽  
Proposed Model ◽  
Gas Sensing Properties ◽  
Acceptable Agreement

Phosphorene is a new two-dimensional material that has great potentials in Nano electronic application, so it has attracted more researchers’ attention nowadays. Indeed, phosphorene is an interesting material in gas sensing, due to its high surface-to-volume ratio and its carrier mobility. Many studies have been reported on phosphorene gas sensing, but there is not enough study on analytical modeling of phosphorene gas sensing properties. In this research, by adopting data from experimental NO2-based gas sensor, an analytical model of the phosphorene gas sensing behavior is presented. Then, the experimental results of NO2 gas sensing are compared with the proposed model and acceptable agreement is reported. This new model is adapted to predict phosphorene gas sensing performance in higher NO2 gas concentrations, which demonstrates, linear relation is established in higher concentrations same as lower ppb NO2 gas concentration. So, we have predicted the result of NO2 gas sensing for higher concentration based on experimental sensing.

scholarly journals 2D Materials for Gas Sensing Applications: A Review on Graphene Oxide, MoS2, WS2 and Phosphorene

Sensors ◽  
2018 ◽  
Vol 18 (11) ◽  
pp. 3638 ◽  
Author(s):  
Maurizio Donarelli ◽  
Luca Ottaviano
Keyword(s):  
Graphene Oxide ◽  
Gas Sensing ◽  
2D Materials ◽  
High Surface ◽  
Volume Ratio ◽  
Thick Layer ◽  
Research Field ◽  
First Year ◽  
Sensing Applications ◽  
Recent Developments

After the synthesis of graphene, in the first year of this century, a wide research field on two-dimensional materials opens. 2D materials are characterized by an intrinsic high surface to volume ratio, due to their heights of few atoms, and, differently from graphene, which is a semimetal with zero or near zero bandgap, they usually have a semiconductive nature. These two characteristics make them promising candidate for a new generation of gas sensing devices. Graphene oxide, being an intermediate product of graphene fabrication, has been the first graphene-like material studied and used to detect target gases, followed by MoS2, in the first years of 2010s. Along with MoS2, which is now experiencing a new birth, after its use as a lubricant, other sulfides and selenides (like WS2, WSe2, MoSe2, etc.) have been used for the fabrication of nanoelectronic devices and for gas sensing applications. All these materials show a bandgap, tunable with the number of layers. On the other hand, 2D materials constituted by one atomic species have been synthetized, like phosphorene (one layer of black phosphorous), germanene (one atom thick layer of germanium) and silicone (one atom thick layer of silicon). In this paper, a comprehensive review of 2D materials-based gas sensor is reported, mainly focused on the recent developments of graphene oxide, exfoliated MoS2 and WS2 and phosphorene, for gas detection applications. We will report on their use as sensitive materials for conductometric, capacitive and optical gas sensors, the state of the art and future perspectives.

scholarly journals Inkjet Printing of Controlled ZnO Nanoparticles Layering

2019 ◽  
Vol 8 (1) ◽  
pp. 34-40
Author(s):  
N. Spinella ◽  
C. Galati ◽  
L. Renna
Keyword(s):  
Zno Nanoparticles ◽  
Gas Sensing ◽  
High Surface ◽  
Volume Ratio ◽  
Specific Chemical ◽  
Force Microscopy ◽  
Electron Microscopies ◽  
Atomic Force ◽  
Preliminary Study

 Controlled layering of functional material can produced a versatile film with specific chemical and physical proprieties for desirable applications. This article presented inkjet multilayer structures of ZnO nanoparticles of specific layer morphology and thickness for the development of devices where a high surface-to-volume ratio is required (e.g. micro gas sensors). Stacked multilayers were stratified through a multi-run printing process suitable to produce large-square pattern on flat silicon support. The formation of a multilayer structure was demonstrate through an extended structural characterization of the resulting film. Printed layer morphology was investigated with optical and scanning electron microscopies; atomic force microscopy profiling characterizations were conducted over the entire printed area to evaluate the pattern reproducibility. Finally, a preliminary study as gas sensing film was performed, using the alcohol/ZnO interaction experiments.

scholarly journals Electrically Transduced Gas Sensors Based on Semiconducting Metal Oxide Nanowires

Sensors ◽  
2020 ◽  
Vol 20 (23) ◽  
pp. 6781
Author(s):  
Ying Wang ◽  
Li Duan ◽  
Zhen Deng ◽  
Jianhui Liao
Keyword(s):  
Metal Oxide ◽  
Low Power ◽  
Gas Sensors ◽  
Gas Sensing ◽  
Volume Ratio ◽  
High Sensitivity ◽  
Disease Diagnosis ◽  
Thermal Stabilities ◽  
Semiconducting Metal Oxide ◽  
Sensing Performance

Semiconducting metal oxide-based nanowires (SMO-NWs) for gas sensors have been extensively studied for their extraordinary surface-to-volume ratio, high chemical and thermal stabilities, high sensitivity, and unique electronic, photonic and mechanical properties. In addition to improving the sensor response, vast developments have recently focused on the fundamental sensing mechanism, low power consumption, as well as novel applications. Herein, this review provides a state-of-art overview of electrically transduced gas sensors based on SMO-NWs. We first discuss the advanced synthesis and assembly techniques for high-quality SMO-NWs, the detailed sensor architectures, as well as the important gas-sensing performance. Relationships between the NWs structure and gas sensing performance are established by understanding general sensitization models related to size and shape, crystal defect, doped and loaded additive, and contact parameters. Moreover, major strategies for low-power gas sensors are proposed, including integrating NWs into microhotplates, self-heating operation, and designing room-temperature gas sensors. Emerging application areas of SMO-NWs-based gas sensors in disease diagnosis, environmental engineering, safety and security, flexible and wearable technology have also been studied. In the end, some insights into new challenges and future prospects for commercialization are highlighted.

scholarly journals Improving the ammonia sensing of reduced graphene oxide film by using metal nano-materials

2015 ◽  
Vol 18 (3) ◽  
pp. 72-77
Author(s):  
Hoa Tran My Huynh ◽  
Thu Thi Hoang ◽  
Thanh Thi Phuong Nguyen ◽  
Tham Ngoc Nguyen ◽  
Nhung Thi Tuyet Bui ◽  
...  
Keyword(s):  
Graphene Oxide ◽  
Reduced Graphene Oxide ◽  
Gas Adsorption ◽  
Gas Sensing ◽  
High Surface ◽  
Volume Ratio ◽  
Nano Materials ◽  
Gas Sensitivity ◽  
Ammonia Sensing ◽  
Reduced Graphene

Gas sensing is one of the most promising applications for reduced graphene oxide (rGO). High surface-to-volume ratio in conjunction with remaining reactive oxygen functional groups translates into sensitivity to molecular on the rGO surface. The response of the rGO based devices can be further improved by functionalizing its surface with metal nano-materials. In this paper, we report the ammonia (NH3) sensing behavior of rGO based sensors functionalized with nano-structured metal: silver (Ag) or platinum (Pt) or gold (Au) in air at room temperature and atmospheric pressure. The gas response is detected by the monitoring changes in electrical resistance of the rGO/metal hybrids due to NH3 gas adsorption. Compared to bare rGO, significantly improved NH3 sensitivity is observed with the addition of nano-structured metals. These materials are applied to play the small bridges role connecting many graphene islands together to improve electrical conduction of hybrids while maintaining the inherent advantage of rGO for NH3 gas sensitivity.

scholarly journals Enhanced Sensitivity of CO on Two-Dimensional, Strained, and Defective GaSe

Molecules ◽  
2021 ◽  
Vol 26 (4) ◽  
pp. 812
Author(s):  
Hsin-Pan Huang ◽  
Huei-Ru Fuh ◽  
Ching-Ray Chang
Keyword(s):  
Adsorption Energy ◽  
Gas Sensing ◽  
High Surface ◽  
Co Adsorption ◽  
Volume Ratio ◽  
Vacancy Defect ◽  
Unstable State ◽  
Strain Effect ◽  
Two Dimensional ◽  
Human Beings

The toxic gas carbon monoxide (CO) is fatal to human beings and it is hard to detect because of its colorless and odorless properties. Fortunately, the high surface-to-volume ratio of the gas makes two-dimensional (2D) materials good candidates for gas sensing. This article investigates CO sensing efficiency with a two-dimensional monolayer of gallium selenide (GaSe) via the vacancy defect and strain effect. According to the computational results, defective GaSe structures with a Se vacancy have a better performance in CO sensing than pristine ones. Moreover, the adsorption energy gradually increases with the scale of tensile strain in defective structures. The largest adsorption energy reached −1.5 eV and the largest charger transfer was about −0.77 e. Additionally, the CO gas molecule was deeply dragged into the GaSe surface. We conclude that the vacancy defect and strain effect transfer GaSe to a relatively unstable state and, therefore, enhance CO sensitivity. The adsorption rate can be controlled by adjusting the strain scale. This significant discovery makes the monolayer form of GaSe a promising candidate in CO sensing. Furthermore, it reveals the possibility of the application of CO adsorption, transportation, and releasement.

scholarly journals Influence of Humidity on NO2-Sensing and Selectivity of Spray-CVD Grown ZnO Thin Film above 400 °C

Chemosensors ◽  
2019 ◽  
Vol 7 (3) ◽  
pp. 42 ◽  
Author(s):  
Lontio Fomekong ◽  
Saruhan
Keyword(s):  
Thin Film ◽  
Relative Humidity ◽  
Gas Sensing ◽  
High Surface ◽  
Volume Ratio ◽  
Phase Identification ◽  
Selectivity Ratio ◽  
Zno Thin Film ◽  
Sensor Signal ◽  
Sensing Applications

Thin films are being used more and more in gas sensing applications, relying on their high surface area to volume ratio. In this study, ZnO thin film was produced through a thermal aerosol spraying and chemical vapor deposition (spray-CVD) process at 500 °C using zinc acetate as a precursor. The phase identification and the morphologies of the film were investigated by XRD and SEM, respectively. Gas-sensing properties of the ZnO thin film were evaluated toward NO2, CO, and NO at a moderate temperature range (400–500 °C) in dry and humid air (relative humidity = 2.5, 5, 7.5, and 10% RH). The obtained results show good sensor signal for both NO2 (R/R0 = 94%) and CO (92%) and poor sensor signal to NO (52%) at an optimum temperature of 450 °C in dry air. The response and recovery times decrease with the increase of NO2 concentration. In the presence of humidity (10% of RH), the sensor is more than twice as sensitive to NO2 (70%) as CO (29%), and accordingly, exhibits good selectivity toward NO2. As the amount of humidity increases from 2.5 to 10% RH, the selectivity ratio of ZnO thin film to NO2 against CO increases from 1 to 2.4. It was also observed that the response and the recovery rates decrease with the increase of relative humidity. The significant enhancement of the selectivity of ZnO thin film toward NO2 in the presence of humidity was attributed to the strong affinity of OH species with NO2.

Sign in / Sign up

Export Citation Format

Share Document