scholarly journals Study on Electrical Performance of a U-Type Microfluidic Acceleration Switch Using Salt Solution as the Sensitive Electrode

Sensors ◽  
2020 ◽  
Vol 20 (24) ◽  
pp. 7062
Author(s):  
Teng Shen ◽  
Yang Chen ◽  
Jiaqing Chang ◽  
Jianhui Zhang ◽  
Xingxing Liu
Keyword(s):  
Salt Solution ◽  
Liquid Surface ◽  
Electrical Performance ◽  
Dynamic Threshold ◽  
High Threshold ◽  
Displacement Curve ◽  
Flow Process ◽  
Low Viscosity ◽  
Inertial Switch ◽  
Sensitive Electrode

The threshold of microfluidic inertial switch is excessively dependent on the size of the passive valve structure and the gas–liquid surface energy of working liquid. How to achieve high threshold and anti-high overload using liquid with low viscosity and low surface tension is a challenging work. Based on the designed U-type microfluidic inertial switch, the electrical characteristic of salt solution at microscale as well as the threshold and dynamic electrical performance of switch were studied. The VOF and CSD modules in CFD software were employed to analyze the dynamic flow process, and then the air–liquid surface moving displacement curve was compared by the theoretical model. A self-designed acceleration test platform was utilized to measure the static threshold, dynamic threshold, and anti-high overload of the inertial switch. The results show that the U-type microfluidics inertial switch using salt solution as sensitive electrode has better performance in power connection and anti-high overload. In particular, it also has the ability to achieve a range of dynamic threshold by changing the placement of the contact electrode, which can achieve rapid power on and off.

Friction and the Continuum Limit – Where is the Boundary?

2000 ◽  
Vol 651 ◽  
Author(s):  
Yingxi Zhu ◽  
Steve Granick
Keyword(s):  
Continuum Limit ◽  
Fluid Transport ◽  
Liquid Surface ◽  
Microfluidic Devices ◽  
Slip Boundary Condition ◽  
Surface Interactions ◽  
Slip Boundary ◽  
Low Viscosity ◽  
Solid Liquid ◽  
The Continuum

AbstractThe no-slip boundary condition, believed to describe macroscopic flow of low-viscosity fluids, overestimates hydrodynamic forces starting at lengths corresponding to hundreds of molecular dimensions when water or tetradecane is placed between smooth nonwetting surfaces whose spacing varies dynamically. When hydrodynamic pressures exceed 0.1-1 atmospheres (this occurs at spacings that depend on the rate of spacing change), flow becomes easier than expected. Therefore solid-liquid surface interactions influence not just molecularly-thin confined liquids but also flow at larger length scales. This points the way to strategies for energy-saving during fluid transport and may be relevant to filtration, colloidal dynamics, and microfluidic devices, and shows a hitherto-unappreciated dependence of slip on velocity.

Microfluidic inertial switch with high threshold and long pulse-width response

2019 ◽  
Vol 27 (1) ◽  
pp. 101-109
Author(s):  
李嘉杰 LI Jia-jie ◽  
聂伟荣 NIE Wei-rong ◽  
刘国伟 LIU Guo-wei
Keyword(s):  
Pulse Width ◽  
High Threshold ◽  
Inertial Switch ◽  
Long Pulse

scholarly journals Boostream: a dynamic fluid flow process to assemble nanoparticles at liquid interface

2017 ◽  
Vol 18 (6) ◽  
pp. 602 ◽  
Author(s):  
Olivier Delléa ◽  
Olivier Lebaigue
Keyword(s):  
Fluid Flow ◽  
Process Parameters ◽  
Hydraulic Jump ◽  
Liquid Surface ◽  
Slope Angle ◽  
Surface Profile ◽  
Liquid Interface ◽  
Main Process ◽  
Experimental Setup ◽  
Flow Process

CEA-LITEN develops an original process called Boostream® to manipulate, assemble and connect micro- or nanoparticles of various materials, sizes, shapes and functions to obtain monolayer colloidal crystals (MCCs). This process uses the upper surface of a liquid film flowing down a ramp to assemble particles in a manner that is close to the horizontal situation of a Langmuir–Blodgett film construction. In presence of particles at the liquid interface, the film down-flow configuration exhibits an unusual hydraulic jump which results from the fluid flow accommodation to the particle monolayer. In order to master our process, the fluid flow has been modeled and experimentally characterized by optical means, such as with the moiré technique that consists in observing the reflection of a succession of periodic black-and-red fringes on the liquid surface mirror. The fringe images are deformed when reflected by the curved liquid surface associated with the hydraulic jump, the fringe deformation being proportional to the local slope of the surface. This original experimental setup allowed us to get the surface profile in the jump region and to measure it along with the main process parameters (liquid flow rate, slope angle, temperature sensitive fluid properties such as dynamic viscosity or surface tension, particle sizes). This work presents the experimental setup and its simple model, the different experimental characterization techniques used and will focus on the way the hydraulic jump relies on the process parameters.

The Use of Styrenes as Embedding Media for Electron Microscopy

1971 ◽  
Vol 29 ◽  
pp. 488-489
Author(s):  
Edward D. De-Lamater ◽  
Eric Johnson ◽  
Thad Schoen ◽  
Cecil Whitaker
Keyword(s):  
Electron Microscopy ◽  
Surface Tension ◽  
Ultraviolet Light ◽  
Methyl Ethyl Ketone Peroxide ◽  
Methyl Ethyl ◽  
Styrene Polymerization ◽  
Radical Initiation ◽  
Tertiary Butyl ◽  
Low Viscosity ◽  
Free Radical Initiation

Monomeric styrenes are demonstrated as excellent embedding media for electron microscopy. Monomeric styrene has extremely low viscosity and low surface tension (less than 1) affording extremely rapid penetration into the specimen. Spurr's Medium based on ERL-4206 (J.Ultra. Research 26, 31-43, 1969) is viscous, requiring gradual infiltration with increasing concentrations. Styrenes are soluble in alcohol and acetone thus fitting well into the usual dehydration procedures. Infiltration with styrene may be done directly following complete dehydration without dilution.Monomeric styrenes are usually inhibited from polymerization by a catechol, in this case, tertiary butyl catechol. Styrene polymerization is activated by Methyl Ethyl Ketone peroxide, a liquid, and probably acts by overcoming the inhibition of the catechol, acting as a source of free radical initiation.Polymerization is carried out either by a temperature of 60°C. or under ultraviolet light with wave lengths of 3400-4000 Engstroms; polymerization stops on removal from the ultraviolet light or heat and is therefore controlled by the length of exposure.

Some quantitative applications of vascular corrosion casting

1992 ◽  
Vol 50 (1) ◽  
pp. 738-739
Author(s):  
Fred E. Hossler
Keyword(s):  
Blood Vessels ◽  
Nuclear Orientation ◽  
Three Dimensional ◽  
Surrounding Tissue ◽  
Confocal Laser ◽  
Corrosion Casting ◽  
Venous Valve ◽  
Casting Technique ◽  
Low Viscosity ◽  
Quantitative Measurements

Preparation of replicas of the complex arrangement of blood vessels in various organs and tissues has been accomplished by infusing low viscosity resins into the vasculature. Subsequent removal of the surrounding tissue by maceration leaves a model of the intricate three-dimensional anatomy of the blood vessels of the tissue not obtainable by any other procedure. When applied with care, the vascular corrosion casting technique can reveal fine details of the microvasculature including endothelial nuclear orientation and distribution (Fig. 1), locations of arteriolar sphincters (Fig. 2), venous valve anatomy (Fig. 3), and vessel size, density, and branching patterns. Because casts faithfully replicate tissue vasculature, they can be used for quantitative measurements of that vasculature. The purpose of this report is to summarize and highlight some quantitative applications of vascular corrosion casting. In each example, casts were prepared by infusing Mercox, a methyl-methacrylate resin, and macerating the tissue with 20% KOH. Casts were either mounted for conventional scanning electron microscopy, or sliced for viewing with a confocal laser microscope.

Investigation of thin sections of biological standards by EDX, EELS, and Auger electron spectroscopy

1990 ◽  
Vol 48 (2) ◽  
pp. 184-185
Author(s):  
S. Lehner ◽  
H.E. Bauer ◽  
R. Wurster ◽  
H. Seiler
Keyword(s):  
Processing System ◽  
Beam Current ◽  
Beam Diameter ◽  
Thin Sections ◽  
Biologically Relevant ◽  
Energy Filtering ◽  
Low Viscosity ◽  
Carbon Foils ◽  
Electron Microscopical ◽  
Exchange Membrane

In order to compare different microanalytical techniques commercially available cation exchange membrane SC-1 (Stantech Inc, Palo Alto), was loaded with biologically relevant elements as Na, Mg, K, and Ca, respectively, each to its highest possible concentration, given by the number concentration of exchangeable binding sites (4 % wt. for Ca). Washing in distilled water, dehydration through a graded series of ethanol, infiltration and embedding in Spurr’s low viscosity epoxy resin was followed by thin sectioning. The thin sections (thickness of about 50 nm) were prepared on carbon foils and mounted on electron microscopical finder grids.The samples were analyzed with electron microprobe JXA 50A with transmitted electron device, EDX system TN 5400, and on line operating image processing system SEM-IPS, energy filtering electron microscope CEM 902 with EELS/ESI and Auger spectrometer 545 Perkin Elmer.With EDX, a beam current of some 10-10 A and a beam diameter of about 10 nm, a minimum-detectable mass of 10-20 g Ca seems within reach.

Ultrastructural autoradiography of L6 skeletal-muscle cells exposed to a tritiated macrolide antibiotic (LY237216) in vitro

1992 ◽  
Vol 50 (1) ◽  
pp. 612-613
Author(s):  
S.L. White ◽  
C.B. Jensen ◽  
D.D. Giera ◽  
D.A. Laska ◽  
M.N. Novilla ◽  
...  
Keyword(s):  
Skeletal Muscle ◽  
Quantitative Analysis ◽  
Macrolide Antibiotic ◽  
Circle Method ◽  
Apical Surface ◽  
Polycarbonate Membrane ◽  
L6 Cells ◽  
Low Viscosity ◽  
Erythromycin A

In vitro exposure to LY237216 (9-Deoxo-11-deoxy-9,11-{imino[2-(2-methoxyethoxy)ethylidene]-oxy}-(9S)-erythromycin), a macrolide antibiotic, was found to induce cytoplasmic vacuolation in L6 skeletal muscle myoblast cultures (White, S.L., unpubl). The present study was done to determine, by autoradiographic quantitative analysis, the subcellular distribution of 3H-LY237216 in L6 cells.L6 cells (ATCC, CRL 1458) were cultured to confluency on polycarbonate membrane filters (Millipore Corp., Bedford, MA) in M-199 medium (GIBCO® Labs) with 10% fetal bovine serum. The cells were exposed from the apical surface for 1-hour to unlabelled-compound (0 μCi/ml) or 50 (μCi/ml of 3H-LY237216 at a compound concentration of 0.25 mg/ml. Following a rapid rinse in compound-free growth medium, the cells were slam-frozen against a liquid nitrogen cooled, polished copper block in a CF-100 cryofixation unit (LifeCell Corp., The Woodlands, TX). Specimens were dried in the MDD-C Molecular Distillation Drier (LifeCell Corp.), vapor osmicated and embedded in Spurrs low viscosity resin. Ultrathin sections collected on formvar coated stainless steel grids were counter-stained, then individually mounted on corks. A monolayer of Ilford L4 nuclear emulsion (Polysciences, Inc., Warrington, PA) was placed on the sections, utilizing a modified “loop method”. The emulsions were exposed for 7-weeks in a light-tight box at 4°C. Autoradiographs were developed in Microdol-X developer and examined on a Philips EM410LS transmission electron microscope. Quantitative analysis of compound localization employed the point and circle approach of Williams; incorporating the probability circle method of Salpeter and McHenry.

Metal Microstructures in Advanced CMOS Devices

1996 ◽  
Vol 54 ◽  
pp. 358-359
Author(s):  
L. M. Gignac ◽  
K. P. Rodbell
Keyword(s):  
Grain Boundaries ◽  
Semiconductor Device ◽  
Chemical Vapor ◽  
Microstructural Characterization ◽  
Metal Films ◽  
Thin Metal ◽  
Electrical Performance ◽  
Thin Metal Films ◽  
Chemical Vapor Deposited ◽  
Boundary Properties

As advanced semiconductor device features shrink, grain boundaries and interfaces become increasingly more important to the properties of thin metal films. With film thicknesses decreasing to the range of 10 nm and the corresponding features also decreasing to sub-micrometer sizes, interface and grain boundary properties become dominant. In this regime the details of the surfaces and grain boundaries dictate the interactions between film layers and the subsequent electrical properties. Therefore it is necessary to accurately characterize these materials on the proper length scale in order to first understand and then to improve the device effectiveness. In this talk we will examine the importance of microstructural characterization of thin metal films used in semiconductor devices and show how microstructure can influence the electrical performance. Specifically, we will review Co and Ti silicides for silicon contact and gate conductor applications, Ti/TiN liner films used for adhesion and diffusion barriers in chemical vapor deposited (CVD) tungsten vertical wiring (vias) and Ti/AlCu/Ti-TiN films used as planar interconnect metal lines.

The concerted use of SEM, TEM, and SCM for examination of resin-dentin interfaces

1994 ◽  
Vol 52 ◽  
pp. 476-477
Author(s):  
B. Van Meerbeek ◽  
L. J. Conn ◽  
E. S. Duke
Keyword(s):  
Surface Layer ◽  
Stress Distribution ◽  
Phosphoric Acid ◽  
Bonding Mechanism ◽  
Restorative Dentistry ◽  
Dental Adhesive ◽  
Low Viscosity ◽  
Dentin Adhesives ◽  
Acid Etch ◽  
Tooth Tissue

Restoration of decayed teeth with tooth-colored materials that can be bonded to tooth tissue has been a highly desirable property in restorative dentistry for many years. Advantages of such an adhesive restorative technique over conventional techniques using non-adhesive metal-based restoratives include improved restoration retention with minimal sacrifice of sound tooth tissue for retention purposes, superior adaptation and sealing of the restoration margins in prevention of caries recurrence, improved stress distribution across the tooth-restoration interface throughout the whole tooth, and even reinforcement of weakened tooth structures. The dental adhesive technology is rapidly changing. An efficient resin bond to enamel has already long been achieved. Its bonding mechanism has been fully elucidated and has proven to be a durable and reliable clinical treatment. However, bonding to dentin represents a greater challenge. After the failures of a dentin acid-etch technique in imitation of the enamel phosphoric-acid-etch technique and a bonding procedure based on chemical adhesion, modern dentin adhesives are currently believed to bond to dentin by a micromechanical hybridization process. This process is developed by an initial demineralization of the dentin surface layer with acid etchants exposing a collagen fibril arrangement with interfibrillar microporosities that subsequently become impregnated by low-viscosity monomers. Although the development of such a hybridization process has well been documented in the literature, questions remain with respect to parameters of-primary importance to adhesive efficacy.

The microstructure of functionalized poLyacrylonitrile beads for bioseparations

1990 ◽  
Vol 48 (4) ◽  
pp. 1094-1095
Author(s):  
Eduardo A. Kamenetzky ◽  
David A. Ley
Keyword(s):  
Aqueous Solution ◽  
Affinity Chromatography ◽  
Pore Size Distribution ◽  
Pore Size ◽  
Surface Coverage ◽  
Vacuum Impregnation ◽  
Thin Sections ◽  
Selective Staining ◽  
Low Viscosity ◽  
Diamond Knife

The microstructure of polyacrylonitrile (PAN) beads for affinity chromatography bioseparations was studied by TEM of stained ultramicrotomed thin-sections. Microstructural aspects such as overall pore size distribution, the distribution of pores within the beads, and surface coverage of functionalized beads affect performance properties. Stereological methods are used to quantify the internal structure of these chromatographic supports. Details of the process for making the PAN beads are given elsewhere. TEM specimens were obtained by vacuum impregnation with a low-viscosity epoxy and sectioning with a diamond knife. The beads can be observed unstained. However, different surface functionalities can be made evident by selective staining. Amide surface coverage was studied by staining in vapor of a 0.5.% RuO4 aqueous solution for 1 h. RuO4 does not stain PAN but stains, amongst many others, polymers containing an amide moiety.

Sign in / Sign up

Export Citation Format

Share Document