scholarly journals A Low-Band Multi-Gain LNA Design for Diversity Receive Module with 1.2 dB NF

Sensors ◽  
2021 ◽  
Vol 21 (24) ◽  
pp. 8340
Author(s):  
Behnam S. Rikan ◽  
David Kim ◽  
Kyung-Duk Choi ◽  
Seyed Ali H. Asl ◽  
Joon-Mo Yoo ◽  
...  
Keyword(s):  
Noise Figure ◽  
Supply Voltage ◽  
High Gain ◽  
Low Noise ◽  
Drop Out ◽  
Common Source ◽  
Frequency Bands ◽  
Voltage Compensator ◽  
Current Consumption ◽  
Lna Design

This paper presents and discusses a Low-Band (LB) Low Noise Amplifier (LNA) design for a diversity receive module where the application is for multi-mode cellular handsets. The LB LNA covers the frequency range between 617 MHz to 960 MHz in 5 different frequency bands and a 5 Pole Single Throw (5PST) switch selects the different frequency bands where two of them are for the main and three for the auxiliary bands. The presented structure covers the gain modes from −12 to 18 dB with 6 dB gain steps where each gain mode has a different current consumption. In order to achieve the Noise Figure (NF) specifications in high gain modes, we have adopted a cascode Common-Source (CS) with inductive source degeneration structure for this design. To achieve the S11 parameters and current consumption specifications, the core and cascode transistors for high gain modes (18 dB, 12 dB, and 6 dB) and low gain modes (0 dB, −6 dB, and −12 dB) have been separated. Nevertheless, to keep the area low and keep the phase discontinuity within ±10∘, we have shared the degeneration and load inductors between two cores. To compensate the performance for Process, Voltage, and Temperature (PVT) variations, the structure applies a Low Drop-Out (LDO) regulator and a corner case voltage compensator. The design has been proceeded in a 65-nm RSB process design kit and the supply voltage is 1 V. For 18 dB and −12 dB gain modes as two examples, the NF, current consumption, and Input Third Order Intercept Point (IIP3) values are 1.2 dB and 16 dB, 10.8 mA and 1.2 mA, and −6 dBm and 8 dBm, respectively.

scholarly journals A concurrent dual-band CMOS low noise amplifier at 2.4/5.2 GHz for WLAN applications

2019 ◽  
Vol 14 (2) ◽  
pp. 555
Author(s):  
S.A.Z. Murad ◽  
A. F. Hasan ◽  
A. Azizan ◽  
A. Harun ◽  
J. Karim
Keyword(s):  
Noise Figure ◽  
Supply Voltage ◽  
Notch Filter ◽  
Cmos Technology ◽  
High Gain ◽  
Low Noise ◽  
Low Noise Amplifier ◽  
Dual Band ◽  
Common Source ◽  
Noise Amplifier

<span>This paper presents a concurrent dual-band CMOS low noise amplifier (LNA) at operating frequency of 2.4 GHz and 5.2 GHz for WLAN applications. The proposed LNA employed cascode common source to obtain high gain using 0.13-µm CMOS technology. The concurrent dual-band frequencies are matched using LC network band-pass and band-stop notch filter at the input and output stages. The filters help to shape the frequency response of the proposed LNA. The simulation results indicate that the LNA achieves a forward gain of 21.8 dB and 14.22 dB, input return loss of -18 dB and -14 dB at 2.4 GHz and 5.2 GHz, respectively. The noise figure of 4.1 dB and 3.5 dB with the input third-order intercept points 7 dBm and 10 dBm are obtained at 2.4 GHz and 5.2 GHz, respectively. The LNA dissipates 2.4 mW power at 1.2 V supply voltage with a chip size of 1.69 mm2.</span>

Inductive Feedback Technique for Design of High Gain 0.18μm CMOS LNA for 5G Applications

2021 ◽  
pp. 2150236
Author(s):  
Anjana Jyothi Banu ◽  
G. Kavya ◽  
D. Jahnavi
Keyword(s):  
Reflection Coefficient ◽  
Noise Figure ◽  
Cmos Technology ◽  
High Gain ◽  
Low Noise ◽  
Common Source ◽  
Matching Network ◽  
Input Matching ◽  
Cmos Lna ◽  
Noise Amplifier

A 26[Formula: see text]GHz low-noise amplifier (LNA) designed for 5G applications using 0.18[Formula: see text][Formula: see text]m CMOS technology is proposed in this paper. The circuit includes a common-source in the first stage to suppress the noise in the amplifier. The successive stage has a Cascode topology along with an inductive feedback to improve the power gain. The input matching network is designed to achieve the input reflection coefficient less than [Formula: see text]7dB at the intended frequency. The matching network at the output is designed using inductor–capacitor (LC) components connected in parallel to attain the output reflection coefficient of [Formula: see text]10[Formula: see text]dB. Due to the inductor added in feedback at the second stage. The [Formula: see text] obtained is 18.208[Formula: see text]dB at 26[Formula: see text]GHz with a noise figure (NF) of 2.8[Formula: see text]dB. The power supply given to the LNA is 1.8[Formula: see text]V. The simulation and layout of the presented circuit are performed using Cadence Virtuoso software.

scholarly journals GaN low-noise X-band MMIC amplifier.

2021 ◽  
Vol 2021 (2) ◽  
Author(s):  
E. Kudabay ◽  
◽  
A. Salikh ◽  
V.A. Moseichuk ◽  
A. Krivtsun ◽  
...  
Keyword(s):  
Output Power ◽  
Integrated Circuit ◽  
Noise Figure ◽  
Supply Voltage ◽  
High Electron Mobility Transistor ◽  
Low Noise ◽  
Common Source ◽  
High Electron ◽  
Monolithic Integrated Circuit ◽  
X Band

The purpose of this paper is to design a microwave monolithic integrated circuit (MMIC) for low noise amplifier (LNA) X-band (7-12 GHz) based on technology of gallium nitride (GaN) high electron mobility transistor (HEMT) with a T-gate, which has 100 nm width, on a silicon (Si) semi-insulating substrate of the OMMIC company. The amplifier is based on common-source transistors with series feedback, which was formed by high-impedance transmission line, and with parallel feedback to match noise figure and power gain. The key characteristics of an LNA are noise figure and gain. However, in this paper, it was decided to design the LNA, which should have a good margin in terms of input and output power. As a result, GaN technology was chosen, which has a higher noise figure compared to other technologies, but eliminates the need for an input power limiter, which in turn significantly increases the overall noise figure. As a result LNA MMIC was developed with the following characteristics: noise figure less than 1.6 dB, small-signal gain more than 20 dB, return loss better than -13 dB and output power more than 19 dBm with 1 dB compression in the range from 7 to 12 GHz in dimensions 2x1.5 mm², which has a supply voltage of 8 V and a current consumption of less than 70 mA. However, it should be said that LNA was only modeled in the AWR DE.

scholarly journals A Low-Noise, High-Gain, and Small-Size UWB Mixer Utilizing Negative Impedance Technique and Source Input Method

Electronics ◽  
2021 ◽  
Vol 10 (21) ◽  
pp. 2655
Author(s):  
Zhaokun Zhou ◽  
Xiaoran Li ◽  
Xinghua Wang ◽  
Wei Gu
Keyword(s):  
Flicker Noise ◽  
Noise Figure ◽  
Supply Voltage ◽  
High Gain ◽  
Low Noise ◽  
Ultra Wideband ◽  
Conversion Gain ◽  
Chip Area ◽  
Input Method ◽  
Impedance Technique

This paper presents an ultra-wideband (UWB) down-conversion mixer with low-noise, high-gain and small-size. The negative impedance technique and source input method are applied for the proposed mixer. The negative impedance achieves the dynamic current injection and increases the mixer output impedance, which reduces the mixer flicker noise and increases its conversion gain. The source input method allows the input matching networks to be cancelled, avoiding the noise and loss introduced by the matching resistors, saving the chip area occupied by the matching inductors. The proposed mixer is designed in 45-nm SOI process provided by GlobalFoundries. The simulation results show a conversion gain of 11.4–14.3 dB, ranging from 3.1 to 10.6 GHz, a minimum noise figure of 9.8 dB, a RF port return loss of less than −11 dB, a port-to-port isolation of better than −48 dB, and a core chip area of 0.16 × 0.16 mm2. The power consumption from a 1 V supply voltage is 2.85 mW.

scholarly journals Design and Implementation of Low Noise Amplifier At 60ghz using Current Mirror Feedback

2019 ◽  
Vol 8 (9S3) ◽  
pp. 249-254
Keyword(s):  
Noise Figure ◽  
Supply Voltage ◽  
Cmos Technology ◽  
Low Noise ◽  
Low Noise Amplifier ◽  
Single Stage ◽  
Common Source ◽  
Small Signal ◽  
Total Size ◽  
Noise Amplifier

This discourse used 45nm CMOS technology to design a Low noise amplifier for a Noise figure < 2dB and gain greater than 13dB at the 60GHz unlicensed band of frequency. A single stage, primary cascode LNA is modeled and its small signal model is analyzed. Common source structure is hired in the driver stage to escalate the output power with single stage contours. To enhance small signal gain, simple active transistor feedback and cascode feedback configurations are designed and appended to the basic LNA. In addition to this, current re-use inductor is designed and added to the cascode amplifier which is deliberated to give low power and low noise figure. Small signal analysis of simple active transistor feedback and current re-use inductor has been presented. The measurement results indicated that the input match and the output gain at 60GHz achieves -8dB and 13dB respectively with the supply voltage of 900mV. The frequency response obtained is a narrow band response with 6GHz of bandwidth. The circuit is simulated by Cadence Virtuoso tool. The layout of the related circuit is drawn by means of the Virtuoso Layout editor with total size of 0.1699μm2.

A Low-Power, High-Gain, and Low-Noise 802.11a Down-Conversion Mixer in 0.35-μm SiGe Bi-CMOS Technology

2017 ◽  
Vol 26 (09) ◽  
pp. 1750134 ◽  
Author(s):  
Jun-Da Chen ◽  
Song-Hao Wang
Keyword(s):  
Low Power ◽  
Noise Figure ◽  
Supply Voltage ◽  
Cmos Technology ◽  
High Gain ◽  
Low Noise ◽  
Cmos Process ◽  
Conversion Gain ◽  
Dc Power ◽  
Down Conversion

The paper presents a novel 5.15[Formula: see text]GHz–5.825[Formula: see text]GHz SiGe Bi-CMOS down-conversion mixer for WLAN 802.11a receiver. The architecture used is based on Gilbert cell mixer, the combination of MOS transistors and HBT BJT transistor device characteristics. The hetero-junction bipolar transistor (HBT) topology is adopted at the transconductance stage to improve power gain and reduce noise factor, and the LO series-parallel CMOS switch topology will be applied to reduce supply voltage and dc power at the switching stage. This mixer is implemented in TSMC 0.35-[Formula: see text]m SiGe Bi-CMOS process, and the chip size including the test pads is 1.175*0.843[Formula: see text]mm2. The main advantages for the proposed mixer are high conversion gain, a moderate linearity, low noise figure, and low power. The post-simulation results achieved are as follows: 14[Formula: see text]dB power conversion gain, [Formula: see text]6[Formula: see text]dBm input third-order intercept point (IIP3), 6.85[Formula: see text]dB double side band (DSB) noise figure. The total mixer current is about 1.54[Formula: see text]mA from 1.4[Formula: see text]V supply voltage including output buffer. The total dc power consumption is 2.15[Formula: see text]mW.

scholarly journals A Low-Noise Amplifier Utilizing Current-Reuse Technique and Active Shunt Feedback for MedRadio Band Applications

2020 ◽  
pp. 306-316
Author(s):  
Mutanizam Abdul Mubin ◽  
◽  
Arjuna Marzuki
Keyword(s):  
Low Power ◽  
Return Loss ◽  
Noise Figure ◽  
High Gain ◽  
Low Noise ◽  
Low Noise Amplifier ◽  
Common Source ◽  
Cmos Process ◽  
Current Reuse ◽  
Noise Amplifier

In this work, a low-power 0.18-μm CMOS low-noise amplifier (LNA) for MedRadio applications has been designed and verified. Cadence IC5 software with Silterra’s C18G CMOS Process Design Kit were used for all design and simulation work. This LNA utilizes complementary common-source current-reuse topology and subthreshold biasing to achieve low-power operation with simultaneous high gain and low noise figure. An active shunt feedback circuit is used as input matching network to provide a suitable input return loss. For test and measurement purpose, an output buffer was designed and integrated with this LNA. Inductorless design approach of this LNA, together with the use of MOSCAPs as capacitors, help to minimize the die size. On post-layout simulations with LNA die area of 0.06 mm2 and simulated total DC power consumption of 0.5 mW, all targeted specifications are met. The simulated gain, input return loss and noise figure of this LNA are 16.3 dB, 10.1 dB and 4.9 dB respectively throughout the MedRadio frequency range. For linearity, the simulated input-referred P1dB of this LNA is -26.7 dBm while its simulated IIP3 is -18.6 dBm. Overall, the post-layout simulated performance of this proposed LNA is fairly comparable to some current state-of-the-art LNAs for MedRadio applications. The small die area of this proposed LNA is a significant improvement in comparison to those of the previously reported MedRadio LNAs.

scholarly journals Design and implementation of a broad-band high gain low noise amplifier for 3G/4G applications

2021 ◽  
Vol 23 (2) ◽  
pp. 725
Author(s):  
Ahmed M. Abdelmonem ◽  
Ahmed S. I. Amar ◽  
Amir Almslmany ◽  
Ibrahim L. Abdalla ◽  
Fathi A. Farag
Keyword(s):  
Noise Figure ◽  
Supply Voltage ◽  
Low Cost ◽  
Broad Band ◽  
High Gain ◽  
Low Noise ◽  
Low Noise Amplifier ◽  
Design System ◽  
Matching Network ◽  
Noise Amplifier

The main aim of the paper is designing and implementing a broadband low-noise-amplifier (LNA) based on compensated matching network techniquein order to get high stable gain, low noise figure, low cost and smaller sizefor 3G/4G communication system applications at 2 GHz with bandwidth 600MHz. The Advanced Design System simulates the proposed circuit (ADS).The implementation was done with a class A bias circuit and a low noise transistor BFU 730F with a lower Noise Figure (NFmin) 0.62 dB. Collectorcurrent is measured to be 5.8mA and base current is 19.1μA with a supply voltage of 2.25V. The new design proposed a (NFmin) of 0.62 dB with a 17.8dB high stable amplifier gain. The microstrip lines (MSL) and compensated matching network techniques were used to improve the LNA’s stability and achieve a good result. The LNA board is implemented and assembled on the FR4 botton layer material. The results are virtually non existence equivalent between the simulated and the measured results.

scholarly journals Design of a LNA in the frequency band 1.8-2.2GHz in 0.13μm CMOS Technology

2005 ◽  
Vol 3 ◽  
pp. 299-303
Author(s):  
E. Di Gioia ◽  
C. Hermann ◽  
H. Klar
Keyword(s):  
Noise Figure ◽  
Supply Voltage ◽  
Low Cost ◽  
Operating Mode ◽  
Cmos Technology ◽  
Digital Circuit ◽  
High Gain ◽  
Low Noise ◽  
Noise Amplifier ◽  
Low Supply Voltage

Abstract. The subject of this work is a low noise amplifier (LNA), operating in the frequency range 1.8-2.1GHz. The CMOS 0.13μm technology is used in respect to the low cost of the final device. Among the specifications, a variable gain and an adjustable working frequency are required. In particular, four different working modes are provided: 1.8, 1.9 and 2.1GHz high gain and 2.1GHz low gain. The amplifier is designed to be used as first stage of a receiver for mobile telephony. For this reason low power consumption is taken into consideration (low supply voltage and low drain currents). A simple digital circuit, integrated on-chip, is used to select the operating mode of the LNA by means of two input pins. A Noise figure of 1dB is obtained with a supply voltage of 0.8V.

scholarly journals Ultra-Wide Band LNA Design using Active Inductor with Modified Noise Cancellation Technique

2019 ◽  
Vol 8 (2) ◽  
pp. 2406-2410
Keyword(s):  
Noise Figure ◽  
Supply Voltage ◽  
Wide Band ◽  
Low Noise ◽  
Ultra Wide Band ◽  
Active Inductor ◽  
Cmos Process ◽  
Chip Area ◽  
Chip Size ◽  
Lna Design

An Ultra-Wide Band (UWB) Low Noise Amplifier (LNA) is affective in deciding the chip size and in the implementation cost at Radio Frequency applications. The proposed LNA design with an active inductor is a different solution to trounce the habit of passive inductors to cut the chip area. Designed in 90-nm CMOS process, a voltage gain of 9dB to 15.5dB for a supply voltage of 0.9v to 1.8V with a smallest Noise Figure (NF) of 5.7dB is achieved by the LNA, with low power utilization and at 2.40 GHz, with 345um2 of chip area.

Sign in / Sign up

Export Citation Format

Share Document