scholarly journals Particle Flow Simulation of the Strength and Failure Characteristics of a Layered Composite Rock-Like Sample with a Single Hole

Symmetry ◽  
2021 ◽  
Vol 13 (7) ◽  
pp. 1132
Author(s):  
Guozhu Wang ◽  
Yu Wang ◽  
Lei Song ◽  
Hao Shi ◽  
Mingwei Zhang ◽  
...  
Keyword(s):  
Mechanical Behavior ◽  
Failure Mode ◽  
Failure Modes ◽  
Shear Failure ◽  
Surrounding Rock ◽  
Tensile Failure ◽  
Practical Significance ◽  
Rock Masses ◽  
Engineering Structures ◽  
Layered Rock

Layered rock masses with holes are common in nature. Their mechanical behavior plays an important role in the safety and stability of engineering structures. However, previous studies have concentrated on a single lithological layer, and few studies have reported on the mechanical behavior of layered rock masses with holes. Based on the concept of symmetry, uniaxial compression tests and numerical simulations were performed on rock-like specimens with three layers and a hole in the interlayer. The hole was in the center of the sample and was symmetrical up and down. The influence of the thickness and strength of the interlayer on the mechanical behavior and failure processes of the layered rock masses with holes was investigated. The results show that the peak strength and elastic modulus were associated with the thickness and strength of the interlayer. Three failure modes were observed in the specimens, which were not only related to the thickness and strength of the interlayer, but also affected by the presence of the hole. When the thickness of the interlayer is small, mainly a single failure mode was observed (tensile failure or shear failure). However, when the interlayer was thick, the failure mode was tension-shear mixed failure. The failure mechanism of the specimens was primarily crack propagation at the edge of the hole. These research results can provide a basis for site selection, and the design of surrounding rock protection and support parameters, and thus have important practical significance for improving surrounding rock stability and ensuring construction safety.

scholarly journals Experimental Study of the Mechanical Characteristics of a Rock-Like Material Containing a Preexisting Fissure under Loading and Unloading Triaxial Compression

2020 ◽  
Vol 2020 ◽  
pp. 1-12 ◽  
Author(s):  
Taoli Xiao ◽  
Mei Huang ◽  
Min Gao
Keyword(s):  
Experimental Study ◽  
Failure Mode ◽  
Mechanical Characteristics ◽  
Failure Modes ◽  
Shear Failure ◽  
Triaxial Compression ◽  
Tensile Failure ◽  
Underground Engineering ◽  
Inclination Angles ◽  
Loading And Unloading

An experimental study of a rock-like material containing a preexisting fissure subjected to loading and unloading triaxial compression is carried out, and the results show that the mechanical characteristics of the rock-like specimen depend heavily on the loading paths and the inclination of the fissure. The triaxial loading experiment results show that the failure strength linearly increases, while the residual strength linearly decreases with increasing inclination. Furthermore, specimens subjected to triaxial compression show an “X”-type shear failure mode. The triaxial unloading compression experimental results show that specimens with different inclination angles have various failure modes. Specimens with gentle inclinations show a tensile-shear mix failure mode, specimens with middle inclinations show a shear-sliding failure mode, and specimens with steep inclinations show a tensile failure mode. These findings can be used to forecast excavation-induced instabilities in deep underground engineering rock structures.

scholarly journals An Analytical Model for Fracture Initiation of Radial Drilling-Fracturing in Shale Formations

Lithosphere ◽  
2021 ◽  
Vol 2021 (Special 1) ◽  
Author(s):  
Yuxin Chen ◽  
Yunhong Ding ◽  
Chong Liang ◽  
Yu Bai ◽  
Dawei Zhu ◽  
...  
Keyword(s):  
Failure Mode ◽  
Failure Modes ◽  
Shear Failure ◽  
Fracture Initiation ◽  
In Situ Stress ◽  
Tensile Failure ◽  
Shale Formations ◽  
Biot Coefficient ◽  
Radial Drilling

Abstract Radial drilling-fracturing, the combination of radial drilling and hydraulic fracturing, can guide fractures toward the target area and effectively enhance the recovery of the low permeable reservoir. In this paper, based on the stress superposition principle, we establish an analytical model to predict fracture initiation pressure (FIP) and the shale failure mode for radial drilling-fracturing applied in shale formations. In contrast with the former studies, this model can additionally consider the failure from shale beddings and is more applicable in the shale reservoir. The model classifies the shale failure into three modes and, respectively, gives the criterion for each failure mode. Then, a series of sensitivity analyses is conducted by examining effects of various parameters. By analyzing the variation characteristic of the initiation pressures required for three failure modes, the main conclusions are as follows. Firstly, matrix failure and shear failure along bedding tend to take place when the azimuth of radial borehole is moderate. Small and large azimuths are favorable for the occurrence of tensile failure along bedding. Secondly, a high ratio of horizontal in situ stress predisposes shale to generate matrix failure, and bedding tensile failure and bedding shear failure are apt to occur when the ratio of horizontal in situ stress is low. Thirdly, with the increasing intersection angle of the radial borehole wall and bedding plane, the failure mode apt to occur changes from bedding tensile failure to bedding shear failure and then to matrix failure. Fourthly, shale prefers to yield bedding shear failure under a small Biot coefficient and generate the other two failure modes when Biot coefficient is large. Fifthly, permeability coefficient virtually has no influence on the failure mode of shale. The research clarifies the fracture initiation characteristics of radial drilling-fracturing in shale formations and provides a reference for the field application of radial drilling-fracturing.

scholarly journals Numerical Analysis of the Mechanical Behavior and Failure Mode of Jointed Rock under Uniaxial Tensile Loading

2020 ◽  
Vol 2020 ◽  
pp. 1-13
Author(s):  
Yang Zhao ◽  
Yongning Wu ◽  
Qing Xu ◽  
Lishuai Jiang ◽  
Wanpeng Huang ◽  
...  
Keyword(s):  
Mechanical Behavior ◽  
Failure Mode ◽  
Failure Modes ◽  
Tensile Tests ◽  
Jointed Rock ◽  
Rock Joints ◽  
Tensile Failure ◽  
Uniaxial Tensile ◽  
Direct Tensile ◽  
Rock Specimens

In the field of rock engineering, tensile failure is one of the most significant failure modes due to the presence of joints/fractures. However, due to the limitations of current laboratory testing, it is difficult to carry out direct tensile tests on jointed rock specimens in the laboratory. To study the effect of joints on the mechanical behavior and failure mode of jointed rock specimens, a three-point modeling method that can consider arbitrarily arranged rock joints is deduced and applied to discrete element simulation. The effects of different joint angles (the inclination angle α, rotation angle β, and superimposed angle γ of α and β, where γ is the angle between the joint and horizontal plane), the density (n), and the rate of cutting area (RCA) of the specimen loading surface (LSS) on the tensile strength (σt), elastic modulus in tension (Et), and failure mode of the specimens were analyzed. The results show that the joint angle (considering α, β, and γ) and RCA have a significant effect on the resulting σt and failure mode, while n has a significant effect on Et. The failure mode of the specimen changes from tensile failure along the joint to direct tensile failure of the specimen as γ increases, and the mechanical behavior transitions from unstable to stable. In addition, the main influence of γ on the mechanical behavior of specimens is revealed, and the change process of the failure mode after the cutting of the LSS is analyzed. The present research can be utilized for multiple purposes, including the joint development of surrounding rock and failure dominated by tensile failure in underground engineering, especially for tunnels, roadways, chambers, and so forth.

Machine learning-based failure mode identification of RCSPSW

2021 ◽  
Author(s):  
Dongqi Jiang ◽  
Shanquan Liu ◽  
Tao Chen ◽  
Gang Bi
Keyword(s):  
Machine Learning ◽  
Failure Mode ◽  
Failure Modes ◽  
Shear Failure ◽  
Tall Buildings ◽  
Shear Walls ◽  
Superior Performance ◽  
Ann Model ◽  
Mode Recognition ◽  
Wide Range

<p>Reinforced concrete – steel plate composite shear walls (RCSPSW) have attracted great interests in the construction of tall buildings. From the perspective of life-cycle maintenance, the failure mode recognition is critical in determining the post-earthquake recovery strategies. This paper presents a comprehensive study on a wide range of existing experimental tests and develops a unique library of 17 parameters that affects RCSPSW’s failure modes. A total of 127 specimens are compiled and three types of failure modes are considered: flexure, shear and flexure-shear failure modes. Various machine learning (ML) techniques such as decision trees, random forests (RF), <i>K</i>-nearest neighbours and artificial neural network (ANN) are adopted to identify the failure mode of RCSPSW. RF and ANN algorithm show superior performance as compared to other ML approaches. In Particular, ANN model with one hidden layer and 10 neurons is sufficient for failure mode recognition of RCSPSW.</p>

Study on Failure of Rock Mass around Deep Tunnel

2011 ◽  
Vol 99-100 ◽  
pp. 370-374 ◽  
Author(s):  
Yue Hong Qian ◽  
Ting Ting Cheng ◽  
Xiang Ming Cao ◽  
Chun Ming Song
Keyword(s):  
Rock Mass ◽  
Stress Field ◽  
Failure Modes ◽  
Shear Failure ◽  
Simple Function ◽  
Tensile Failure ◽  
Deep Tunnel ◽  
Main Mode

During excavating the problem of unloading is a dynamic one essentially. Assuming the unloading ruled by a simple function and based on the Hamilton principal, the distribution of the stress field nearby the tunnel is obtained. The characteristics of the failure nearby the tunnel are analyzed considering the shear failure and tensile failure. The results show that the main mode of the shear failure, intact and tensile failure occurs from the tunnel. The characteristic of the shear failure, intact and tensile failure are one of the likely failure modes.

scholarly journals Research on Failure Characteristics of Concrete Three-Point Bending Beams with Preexisting Cracks in Different Positions Based on Numerical Simulation

Geofluids ◽  
2021 ◽  
Vol 2021 ◽  
pp. 1-8
Author(s):  
Liuqun Zhao ◽  
Li Zheng ◽  
Hui Qin ◽  
Tiesuo Geng ◽  
Yonggang Tan ◽  
...  
Keyword(s):  
Acoustic Emission ◽  
Bearing Capacity ◽  
Failure Modes ◽  
Failure Process ◽  
Engineering Application ◽  
Tensile Failure ◽  
Engineering Structures ◽  
Failure Characteristics ◽  
Three Point Bending ◽  
Wide Range

Concrete three-point bending beams with preexisting cracks are widely used to study the growth process of I-II mixed mode cracks. Studying the failure characteristics of preexisting cracks at different locations on concrete three-point bending beams not only has important scientific significance but also has a wide range of engineering application backgrounds in the safety assessment of engineering structures. In this paper, through several numerical experiments, the influence of preexisting cracks at different positions on the failure characteristics of concrete three-point bending beams is studied, and three typical failure modes are obtained. The failure process of the specimens with three typical failure modes is discussed in detail, and it is pointed out that the crack failure mode is tensile failure. The change trends of bearing capacity, acoustic emission quantity, and acoustic emission energy of three typical failure modes are analyzed. The maximum bearing capacity, the maximum acoustic emission quantity, and energy of three failure modes of concrete three-point bending beams generally show an increasing trend.

scholarly journals Failure Characteristics and Mechanism of Multiface Slopes under Earthquake Load Based on PFC Method

2021 ◽  
Vol 2021 ◽  
pp. 1-11
Author(s):  
Tao Yang ◽  
Yunkang Rao ◽  
Huailin Chen ◽  
Bing Yang ◽  
Jiangrong Hou ◽  
...  
Keyword(s):  
Moisture Content ◽  
Failure Mechanism ◽  
Failure Modes ◽  
Shear Failure ◽  
Shaking Table ◽  
Tensile Failure ◽  
Particle Flow Code ◽  
Shear Cracks ◽  
Local Shear ◽  
Shear Slip

Understanding the failure mechanism and failure modes of multiface slopes in the Wenchuan earthquake can provide a scientific guideline for the slope seismic design. In this paper, the two-dimensional particle flow code (PFC2D) and shaking table tests are used to study the failure mechanism of multiface slopes. The results show that the failure modes of slopes with different moisture content are different under seismic loads. The failure modes of slopes with the moisture content of 5%, 8%, and 12% are shattering-shallow slip, tension-shear slip, and shattering-collapse slip, respectively. The failure mechanism of slopes with different water content is different. In the initial stage of vibration, the slope with 5% moisture content produces tensile cracks on the upper surface of the slope; local shear slip occurs at the foot of the slope and develops rapidly; however, a tensile failure finally occurs. In the slope with 8% moisture content, local shear cracks first develop and then are connected into the slip plane, leading to the formation of the unstable slope. A fracture network first forms in the slope with 12% moisture content under the shear action; uneven dislocation then occurs in the slope during vibration; the whole instability failure finally occurs. In the case of low moisture content, the tensile crack plays a leading role in the failure of the slope. But the influence of shear failure becomes greater with the increase of the moisture content.

scholarly journals Experimental Study on Bending Performance of Composite Sandwich Panel with New Mixed Core

2019 ◽  
Vol 275 ◽  
pp. 02018
Author(s):  
Jing Zhang ◽  
Xiamin Hu ◽  
Wan Hong ◽  
Bing Zhang ◽  
Chengli Zhang
Keyword(s):  
Experimental Investigation ◽  
Polyurethane Foam ◽  
Failure Mode ◽  
Shear Failure ◽  
Sandwich Panels ◽  
Tensile Failure ◽  
Bending Test ◽  
Bending Performance ◽  
Composite Sandwich Panels ◽  
Composite Sandwich

This paper presents an experimental investigation of bending performance of composite sandwich panels with new mixed core, sandwich panels were tested by four-point bending test. Parametric study was conducted to investigate the influence of different core materials on the failure mode, ultimate bearing capacity, stiffness and ductility of composite sandwich panels. The results of the experimental investigation showed that the mixed core can change the failure mode of sandwich panels. The failure mode of wooden panels is characterized by tensile failure of bottom wood, and the failure mode of composite sandwich panels with wood core is that the surface layer and core are stripped and the webs are damaged by shear, while the failure mode of composite sandwich panels with wood and polyurethane foam mixed core is the shear failure of the web. Composite sandwich panels with GFRP-wood-polyurethane foam core have better bending performance and can effectively reduce the weight of panels.

Tensile behaviors of co-woven-knitted fabric reinforced composites under various strain rates

2011 ◽  
Vol 45 (24) ◽  
pp. 2495-2506 ◽  
Author(s):  
Pibo Ma ◽  
Hong Hu ◽  
Lvtao Zhu ◽  
Baozhong Sun ◽  
Bohong Gu
Keyword(s):  
Strain Rate ◽  
Failure Modes ◽  
Shear Failure ◽  
High Strain ◽  
Tensile Failure ◽  
Knitted Fabric ◽  
Strain Rates ◽  
High Strain Rates ◽  
Textile Composite ◽  
Interface Failure

This article reports the tensile behaviors of a novel kind of 3D textile composite, named as co-woven-knitted fabric (CWKF) reinforced composite, under quasi-static and high strain rates. The tensile tests were conducted along the warp direction (0°), bias direction (45°), and weft direction (90°) at quasi-static strain rate of 0.001/s and high strain rates ranging from 1589/s to 2586/s. The results indicate that the tensile strength, failure strain, tensile stiffness, energy absorption, and resilient energy are strain rate sensitive along all the three directions. The relationships between the mechanical parameters and the strain rate were also analyzed. The fractograph of the CWKF composite demonstrate that the tensile failure modes are matrix shear failure and fibers breakage under the quasi-static testing condition while interface failure and fibers pullout are at high strain rates.

scholarly journals Cracking Behaviors and Mechanical Properties of Rock-Like Specimens with Two Unparallel Flaws under Conventional Triaxial Compression

2019 ◽  
Vol 2019 ◽  
pp. 1-15 ◽  
Author(s):  
Huilin Le ◽  
Shaorui Sun ◽  
Chenghua Xu ◽  
Liuyang Li ◽  
Yong Liu
Keyword(s):  
Mechanical Properties ◽  
Inclination Angle ◽  
Failure Modes ◽  
Shear Failure ◽  
Triaxial Compression ◽  
Confining Pressure ◽  
Critical Value ◽  
Tensile Failure ◽  
Rock Bridge ◽  
Bridge Length

Flaws existing in rock masses are generally unparallel and under three-dimensional stress; however, the mechanical and cracking behaviors of the specimens with two unparallel flaws under triaxial compression have been rarely studied. Therefore, this study conducted comprehensive research on the cracking and coalescence behavior and mechanical properties of specimens with two unparallel flaws under triaxial compression. Triaxial compressive tests were conducted under different confining pressures on rock-like specimens with two preexisting flaws but varying flaw geometries (with respect to the inclination angle of the two unparallel flaws, rock bridge length, and rock bridge inclination angle). Six crack types and eleven coalescence types in the bridge region were observed, and three types of failure modes (tensile failure, shear failure, and tensile-shear failure) were observed in experiments. Test results show that bridge length and bridge inclination angle have an effect on the coalescence pattern, but the influence of bridge inclination angle is larger than that of the bridge length. When the confining pressure is low, coalescence patterns and failure modes of the specimens are greatly affected by flaw geometry, but when confining pressure rose to a certain level, the influence of confining pressure is larger than the effect of flaw geometry. The peak strength of the specimens is affected by flaw geometry and confining pressure. There is a critical value for the bridge length. If the bridge length is larger than the critical value, peak strengths of the samples almost keep constant as the bridge length increases. In addition, as the bridge inclination angle increases, there is an increase in the probability of tensile cracks occurring, and with an increase in the confining pressure, the probability of the occurrence of shear cracks increases.

Sign in / Sign up

Export Citation Format

Share Document