scholarly journals Research on Failure Characteristics of Concrete Three-Point Bending Beams with Preexisting Cracks in Different Positions Based on Numerical Simulation

Geofluids ◽  
2021 ◽  
Vol 2021 ◽  
pp. 1-8
Author(s):  
Liuqun Zhao ◽  
Li Zheng ◽  
Hui Qin ◽  
Tiesuo Geng ◽  
Yonggang Tan ◽  
...  
Keyword(s):  
Acoustic Emission ◽  
Bearing Capacity ◽  
Failure Modes ◽  
Failure Process ◽  
Engineering Application ◽  
Tensile Failure ◽  
Engineering Structures ◽  
Failure Characteristics ◽  
Three Point Bending ◽  
Wide Range

Concrete three-point bending beams with preexisting cracks are widely used to study the growth process of I-II mixed mode cracks. Studying the failure characteristics of preexisting cracks at different locations on concrete three-point bending beams not only has important scientific significance but also has a wide range of engineering application backgrounds in the safety assessment of engineering structures. In this paper, through several numerical experiments, the influence of preexisting cracks at different positions on the failure characteristics of concrete three-point bending beams is studied, and three typical failure modes are obtained. The failure process of the specimens with three typical failure modes is discussed in detail, and it is pointed out that the crack failure mode is tensile failure. The change trends of bearing capacity, acoustic emission quantity, and acoustic emission energy of three typical failure modes are analyzed. The maximum bearing capacity, the maximum acoustic emission quantity, and energy of three failure modes of concrete three-point bending beams generally show an increasing trend.

Effect of Non-Homogeneity on Limit Bearing Capacity of Rock Block

2008 ◽  
Vol 33-37 ◽  
pp. 631-638
Author(s):  
Li Song ◽  
Tao Xu ◽  
Ying Yan Xie
Keyword(s):  
Numerical Simulations ◽  
Bearing Capacity ◽  
Failure Modes ◽  
Process Analysis ◽  
Failure Process ◽  
Functional Relation ◽  
Acoustic Emissions ◽  
Rock Block ◽  
Homogeneous Material ◽  
Engineering Structures

Rock is a typical non-homogeneous material. The behavior of a rock block under compression and the process of micro-fracture in that block are phenomena of considerable interest in understanding the strength characterization of brittle rock. In this study, the effect of the non-homogeneity on limit bearing capacity of rock block based on Rock Elasto-Plastic Failure Process Analysis code (REPFPA) are simulated and investigated. Numerical simulations find out that there exists a functional relation between the heterogeneity coefficient and the limit bearing capacity of rock block. For specimens with the same heterogeneity, however, the numerical simulations show that the failure modes depend greatly on the crack initiation location, which is found to be sensitive to the local disorder features within the specimen. In addition, the characteristics of acoustic emissions with the changing of heterogeneity coefficient were also found. These identifications are crucial for better understanding and interpreting the experimental results and consequently, improve our concepts in design or analysis of rock engineering structures.

scholarly journals Experimental Study on Axial Compression Behavior of Masonry Columns’ Strengthening with Bamboo Scrimber Bar Mesh Mortar Layer

2020 ◽  
Vol 2020 ◽  
pp. 1-11 ◽  
Author(s):  
Hongyao Liu ◽  
Min Lei ◽  
Bowang Chen
Keyword(s):  
Experimental Study ◽  
Bearing Capacity ◽  
Axial Compression ◽  
Failure Process ◽  
Engineering Application ◽  
Compression Tests ◽  
Compression Behavior ◽  
Bamboo Scrimber ◽  
Calculation Results ◽  
Strengthening Method

We propose a new method to strengthen structural masonry. To study on the axial compression behavior of masonry columns’ strengthening with a bamboo scrimber bar mesh mortar layer, axial compression tests of twelve masonry columns have been completed: nine strengthened columns and three unstrengthened columns. The failure process, bearing capacity, and failure mode are carried out. The strengthening method of bamboo scrimber bar mesh mortar layer permits the upgrade of the columns’ bearing capacity. The effects of bamboo bar ratio and mortar strengthening ratio on bearing capacity of the reinforced columns are compared. We propose the method for calculating the axial bearing capacity of such a reinforced column. The calculation results agree well with the experimental results, and the research results are available for engineering application.

scholarly journals Experimental Study on Hysteretic Behavior of the Overlapped K-Joints with Concrete Filled in Chord

2019 ◽  
Vol 9 (7) ◽  
pp. 1456 ◽  
Author(s):  
Wenwei Yang ◽  
Ruhao Yan ◽  
Yaqi Suo ◽  
Guoqing Zhang ◽  
Bo Huang
Keyword(s):  
Plastic Deformation ◽  
Energy Dissipation ◽  
Cyclic Loading ◽  
Bearing Capacity ◽  
Failure Modes ◽  
The United States ◽  
Hysteretic Behavior ◽  
Tensile Failure ◽  
Element Analysis ◽  
Better Than

Due to the insufficient radial stiffness of the steel tube, the cracking of the weld and the plastic deformation of the string often occur under the cyclic loading of the hollow section pipe joint. In order to avoid such a failure, the overlapped K-joints were strengthened by pouring different concrete into the chords. Furthermore, to explore the detailed effect of filling different concrete in a chord on the hysteretic behavior of the overlapped K-joints, six full-scale specimens were fabricated by two forms, which included the circular chord and braces, the square chord and circular braces, and the low cyclic loading tests, which were carried out. The failure modes, hysteretic curves and skeleton curves of the joints were obtained, and the bearing capacity, ductility and energy dissipation of the joints were evaluated quantitatively. The results showed that plastic failure occurs on the surface of the chord of the joints without filling concrete, while the failure mode of the joints filled with concrete in the chords was the tensile failure of the chords at the weld of the brace toe, and the compressive braces had a certain buckling deformation; The strengthening measures of concrete filled with chord can effectively improve the mechanical properties of the K-joints, the delay of the plastic deformation of the chord, and improve the bearing capacity of the K-joints. Contrarily, the ductility coefficient and the energy dissipation ratio of K-joints decreased with the concrete filled in the chord. The hysteretic behavior of the K-joints with a circular chord and brace was slightly better than that of the K-joints with a square chord and circular brace, and the hysteretic behavior of the K-joints strengthened with fly ash concrete, which was better than that of the K-joints strengthened with ordinary concrete. The results of ANSYS (a large general finite element analysis software developed by ANSYS Company in the United States) analysis agreed well with the experimental results.

Acoustic Emission Characteristics of Rock Failure under Uniaxial Loading

2011 ◽  
Vol 378-379 ◽  
pp. 43-46 ◽  
Author(s):  
Tao Xie ◽  
Qing Hui Jiang ◽  
Rui Chen ◽  
Wei Zhang
Keyword(s):  
Acoustic Emission ◽  
Failure Modes ◽  
Mechanical Performance ◽  
Progressive Failure ◽  
Failure Process ◽  
Testing Machine ◽  
Rock Failure ◽  
Rock Failure Process ◽  
State Variation ◽  
Acoustic Emission Test

With RMT-150C rock testing machine and AEWIN E1.86 DISP acoustic emission system applied, the acoustic emission test was accomplished with two kinds of rock samples including marble and granite under uniaxial compression. Cyclic loading and continuous loading were used through the experiment, and the mechanical performance and acoustic emission (AE) characteristics were obtained during the process of rock progressive failure. Details related to the relationship between amount of AE and stress-strain was given in this paper. A comparison between marble and granite was made as well following the general AE law, on the basis of which, the failure mechanism of rock mass was investigated. Finally, some conclusions can be summarized as follows:(1) AE activity features are different with stress state variation in rock failure process;(2) loading patterns make a direct impact on the failure process thereby affecting AE activities;(3)AE activities are various basing on the different types of rocks, structures and failure modes.

scholarly journals Acoustic Emission and Failure Modes for Coal-Rock Structure under Different Loading Rates

2018 ◽  
Vol 2018 ◽  
pp. 1-11 ◽  
Author(s):  
Ning Wang ◽  
Yingqian Xu ◽  
Dengyuan Zhu ◽  
Nan Wang ◽  
Benfu Yu
Keyword(s):  
Acoustic Emission ◽  
Energy Release ◽  
Failure Modes ◽  
Loading Rate ◽  
Failure Process ◽  
Coal Mass ◽  
Transient Growth ◽  
Loading Rates ◽  
Rock Structure ◽  
Coal Rock

Coal bump refers to a sudden catastrophic failure of coal seam and usually causes serious damages to underground mining facilities and staff. Considering the combined coal-rock structure for coal bumps, failure process and acoustic emission (AE) characteristics of combined coal-sandstone samples under different loading rates were studied by uniaxial compression tests, and three basic failure modes and bump proneness for coal-rock structure were obtained. The following conclusions are drawn: (1) when loading rate was relatively low, plastic deformation of coal mass fully developed, while surface cracks of coal mass was not apparent and slip along the transfixion crack occurred in the postpeak stage; (2) with the increase in loading rate, surface tensile cracks developed into splitting cracks at the end of the prepeak stage and throughout the postpeak stage, and brittle failure finally happened due to the release of nonlinear step-shaped energy or one-time strain energy release of upper rock mass, resulting in the damage of internal bearing structure and weakening of bearing capacity; (3) the deformation and failure process of combined samples showed obvious phases, and corresponding AE energy release rate could be divided into periodic linear growth and transient growth, while the cumulative energy of AE events has multiple peak points and transient growth with the increase of loading rate; (4) it was demonstrated that two distinct frequency bands existed in AE events, which were about 50 kHz and 150 kHz, and the distribution of AE events near 50 kHz was larger and stronger, representing the main frequency range of cracks in coal mass. According to the damage characteristics and AE parameters for combined samples, an brittle model for coal-rock structure with mutation characteristics was proposed, and three basic failure modes for the combined structure with the increase of loading rate were progressive shear failure, splitting failure, and structural failure, respectively.

Study on Carburizing Inspection of Cracking Furnace Tube Using Acoustic Emission Technique

2014 ◽  
Author(s):  
Zhou Fang ◽  
Guodong Jia ◽  
Deyu Liu ◽  
He Yan ◽  
Zhe Wang
Keyword(s):  
Magnetic Field ◽  
Acoustic Emission ◽  
Layer Thickness ◽  
Failure Modes ◽  
Additional Stress ◽  
Emission Signal ◽  
Heating Furnaces ◽  
Wide Range ◽  
Furnace Tube ◽  
Carburized Layer

Large tube type fuel heating furnaces are important and essential equipments, which have a wide range of applications in the petroleum and chemical industry, and failure modes of the furnace tubes in them are mostly caused by carburizing. It is important to improve effective detection technology for the measure of the tube carburized layer thickness, as well as the research on the comprehensive performance of furnace tubes considering the impacts of different conditions. The specifications of Φ70×6 mm HP40Nb cracking furnace tube was studied by experiment method to evaluate the effectiveness of an acoustic emission (AE) technique, which used to measure the carburized layer thickness. In the experiment, many factors were taking into account, such as different carburizing time, the response of acoustic emission attenuation to the organization changes, the magnetic field changes, and additional stress which caused by carburization are considered. The results show that the short periods strong carburizing has obviously impacts in the changes of the organization and magnetic field of the cracking furnace tube, however, it has little contribution to the acoustic emission signal attenuation.

scholarly journals Failure Behaviour of Sandstone with a Preexisting Joint under Stepped Excavation

2020 ◽  
Vol 2020 ◽  
pp. 1-11
Author(s):  
Yinzhu Liu ◽  
Ping Cao ◽  
Liwen He ◽  
Qibin Lin
Keyword(s):  
Failure Modes ◽  
Shear Failure ◽  
Normal Load ◽  
Crack Coalescence ◽  
Tensile Failure ◽  
Type I ◽  
Failure Characteristics ◽  
Excavation Process ◽  
Spalling Failure ◽  
Shear Slip

Much geotechnical construction needs to be carried out under the condition of stepped excavation. However, there is still a lack of research on crack coalescence and failure modes of jointed rock mass under stepped excavation conditions. In order to simulate the stepped excavation test of the real project, the polylactic acid (PLA) material is selected as the filler for the excavation area. The stepped excavation tests are performed on sandstone specimens containing a preexisting joint under different normal load conditions. The dynamic stepped excavation of simulating excavate rock engineering is realised. The constant normal loads during the excavation process are determined to be 80 kN and 100 kN. The influence of the joint inclination on the failure characteristics of the excavation process is analysed. Four typical failure modes are summarised: (a) Mode I: crack coalescence of tensile failure; (b) Mode II: crack coalescence of mixed failure; (c) Mode III: without crack coalescence of mixed failure; (d) Mode IV: without crack coalescence of shear failure. Furthermore, the failure characteristics of the area above the excavation hole and the preexisting joint are analysed. The results show that there are three failure modes: (a) Type I: spalling failure; (b) Type II: shear slip failure; (c) Type III: shear slip and spalling mixed failure.

scholarly journals Behavior of GFRP-Wood Composite Sandwich Beam-Column Joints with Angle Steels

2020 ◽  
Vol 2020 ◽  
pp. 1-15
Author(s):  
ZhiJin Xie ◽  
YuJun Qi ◽  
Hai Fang ◽  
WeiQing Liu
Keyword(s):  
Bearing Capacity ◽  
Failure Modes ◽  
Sandwich Beam ◽  
Tensile Failure ◽  
Wood Composite ◽  
Initial Stiffness ◽  
Composite Sandwich ◽  
Glass Fiber Reinforced ◽  
Connection System ◽  
System Configurations

In this paper, a new type of connection system was proposed for joints between GFRP-wood composite sandwich beams and columns which were made of glass fiber-reinforced polymer (GFRP) face sheets and southern pine wood cores. The connection system comprised steel angles anchored to the column, and the beam was bolted to the angles. Six different connection system configurations were tested to understand the static behavior of the connection system under different parameters including the length of the beam-closed limb and the presence of ribs. The failure modes of the connection system obtained in tests were of three types: yield failure of the angle steels, local crushing failure of the GFRP-wood composite sandwich beam, and tensile failure of the bolt on the beam-closed limb. The initial rotational stiffness values of the three specimens with ribs were 113.75%, 119.56%, and 227.94% higher than the corresponding three specimens without ribs. And the ductility of connection improved by up to 30.28% due to the presence of stiffener ribs. Based on the tests, the bearing capacity and stiffness of the connection system were predicted. For the specimens without ribs, the method in Eurocode 3 was adopted for bearing capacity and stiffness predictions. For the specimens with ribs, a mechanical model was established for bearing capacity and initial stiffness predictions, which was solved according to the corresponding stress features and failure modes. The analytical results were in good agreement with the experimental results.

scholarly journals Numerical tests on thermal cracking characteristics of rocks with different scales

2018 ◽  
Vol 10 (8) ◽  
pp. 168781401879214 ◽  
Author(s):  
Yang Xiao ◽  
Rui Zhao ◽  
Qing-Xiang Huang ◽  
Jun Deng ◽  
Jun-Hui Lu
Keyword(s):  
Acoustic Emission ◽  
Thermal Destruction ◽  
Thermal Damage ◽  
Process Analysis ◽  
Failure Process ◽  
Acoustic Emissions ◽  
Thermal Cracking ◽  
Tensile Failure ◽  
Failure Patterns ◽  
Different Diameters

Realistic failure process analysis, a thermal software simulation, was used to explore the scale effect of thermal cracking of rock under the thermal–mechanical coupling loading. The patterns and characteristics of thermal destruction were analyzed by simulating the thermal cracking of rocks with the same diameter different lengths, the same length but different diameters, and the same size ratio but different sizes (same length/diameter ratio but with different diameters). The acoustic emission and energy changes were also studied during thermal destruction. The results represented that the main forms of thermal cracking are tensile failure and shear failure. The smaller the scale is (length, diameter, and size), the more complex the pattern of thermal damage exhibited as failure patterns of inverted “S” or “V.” With the increasing scale, thermal damage models were simpler. The elastic modulus was determined by the diameter of specimens, and the peak stress was determined by the length of specimens. Overall, as the scale increased, the stress intensity decreased, but the number of acoustic emissions and acoustic emission energy and the corresponding accumulation increased.

System Reliability Study Based on Bearing Capacity Update and Deformation Iteration

2011 ◽  
Vol 368-373 ◽  
pp. 1608-1612
Author(s):  
Hao Liang Zhu ◽  
Wen Bo Sun
Keyword(s):  
Bearing Capacity ◽  
System Reliability ◽  
Failure Modes ◽  
Failure Process ◽  
Scientific Basis ◽  
Structural Testing ◽  
Engineering Project ◽  
Structural Reinforcement ◽  
Distribution Parameters ◽  
Incremental Step

For the sensitive of distribution parameters of random variables, system reliability research should be focus on identifying the significant failure modes, while failure probability as a quantitative reference index, only combining both of them can better estimate system reliability. On the basis of load incremental step theory, a method for identifying the significant failure modes which could more accurately simulate the real failure process for considering the change of bearing capacity and spatial position is proposed in this paper. Then, the corresponding program is prepared with APDL on ANSYS platform. On the one hand, the efficiency and accuracy of identification is improved, on the other hand, the usefulness of this method is enhanced. Finally, the reliability of a space grid engineering project is analyzed and discussed by this method; moreover, the system reliability index β is calculated as well. These analysis results are helpful to provide scientific basis for structural optimization, structural testing, and structural reinforcement and so on.

Sign in / Sign up

Export Citation Format

Share Document