scholarly journals Influence of Rectifier Nozzles on the Flow Distribution Characteristics of Parallel Pipes

Water ◽  
2020 ◽  
Vol 12 (9) ◽  
pp. 2558
Author(s):  
Zhendong Yang ◽  
Yalong Cao ◽  
Qiaoling Zhang ◽  
Feng Wu ◽  
Suqi Shi ◽  
...  
Keyword(s):  
Experimental Studies ◽  
Great Influence ◽  
Flow Distribution ◽  
Distribution Characteristics ◽  
Flow State ◽  
Flow Uniformity ◽  
Inlet Flow ◽  
Partial Cavitation ◽  
New Type ◽  
Resistance Structure

The inhomogeneous distribution of parallel pipe flow leads to difficulty in the efficient and reliable operation of fluid power equipment. In view of this, a new type of rectifier nozzle has been proposed in parallel pipelines. Numerical simulation and experimental studies were used to reveal the influence of the rectification nozzle on the flow distribution characteristics. The hydraulic characteristics of the parallel pipelines with and without rectifier nozzles were compared and analyzed. The effects of the temperature and inlet flow on the flow uniformity were studied. The results showed that the initial temperature had little effect on the flow distribution of parallel pipelines, and the flow rates of the branches were not much different. The inlet flow had great influence on the distribution characteristics of the parallel pipelines, but the rectifier nozzles changed the local resistance structure and pressure distribution at the shunt, thereby improving the non-uniformity of the flow distribution of the parallel pipelines, and the maximum difference between the two pipes was optimized from 28.89 t/h (20.3%) to 2.2 t/h (1.5%). The rectifying nozzle could distort the flow field of each branch during the split, making the distribution of flow rate and flow state more uniform and stable. At high inlet fluid temperatures, cavitation could occur under the pressure drop of the nozzle, and partial cavitation had little effect on the flow distribution.

Experimental Study of Air Distribution Characteristics in Room of Stratum Ventilation under Two Kinds of Air Change Times

2013 ◽  
Vol 409-410 ◽  
pp. 668-672
Author(s):  
Yong Mei Xu ◽  
Jian Tang ◽  
Jun Han ◽  
Chu Qin Lin
Keyword(s):  
Experimental Study ◽  
Thermal Comfort ◽  
Experimental Studies ◽  
Air Distribution ◽  
Distribution Characteristics ◽  
Breathing Zone ◽  
Wind Speeds ◽  
Pollutant Concentrations ◽  
New Type ◽  
Better Than

Aimed at a new type of ventilation - stratum ventilation, air distributions at a breathing-zone in a model office were measured under kinds of air changes, the measure parameters in the experimental studies included temperatures, wind speeds and pollutant concentrations, based on which the thermal comfort at a breathing-zone were studied. Experimental results show that, the temperature, pollutant concentration and wind speeds in a breathing-zone under 5 times air changes are better than those under 6 times air changes. The calculating results of PMV and PPD indicate that the thermal comfort at a breathing-zone under 5 times air changes is better. The experimental study is instructive for the development of the ventilation.

Research on an axial-mounted dual magnetostrictive material rods-based electro-hydrostatic actuator

2021 ◽  
pp. 1045389X2110145
Author(s):  
Yuchuan Zhu ◽  
Chang Liu ◽  
Yunze Song ◽  
Long Chen ◽  
Yulei Jiang ◽  
...  
Keyword(s):  
Mathematical Model ◽  
Flow Rate ◽  
Flow Distribution ◽  
Maximum Flow ◽  
Magnetostrictive Material ◽  
Simulation Techniques ◽  
Motion State ◽  
New Type ◽  
Output Characteristics ◽  
Active Rectification

In this paper, an electro-hydrostatic actuator driven by dual axial-mounted magnetostrictive material rods-based pumps (MMPs) with a new type of active rectification valve is designed in the current study. Based on flow distribution of the active rectification valve and driving energy provided by two MMPs, the actuator can output continuous and bidirectional displacement. By establishing a mathematical model of the actuating system, using simulation techniques, the change rule of hydraulic cylinder’s motion state caused by different driving signals are studied and analyzed. Test equipment platform is constructed in the laboratory to test the output characteristics and confirm the feasibility of the new concept. The experimental results indicate that the maximum flow rate can reach approximately 2.7 L·min−1, while the operating frequency is 180 Hz.

Experimental investigation on the three-dimensional flow field from a meltblowing slot die

e-Polymers ◽  
2020 ◽  
Vol 20 (1) ◽  
pp. 724-732
Author(s):  
Changchun Ji ◽  
Yudong Wang
Keyword(s):  
Flow Field ◽  
Three Dimensional ◽  
Great Influence ◽  
Distribution Characteristics ◽  
Air Velocity ◽  
Three Dimensional Flow ◽  
Dimensional Flow ◽  
Airflow Distribution ◽  
Slot Die ◽  
Center Area

AbstractTo investigate the distribution characteristics of the three-dimensional flow field under the slot die, an online measurement of the airflow velocity was performed using a hot wire anemometer. The experimental results show that the air-slot end faces have a great influence on the airflow distribution in its vicinity. Compared with the air velocity in the center area, the velocity below the slot end face is much lower. The distribution characteristics of the three-dimensional flow field under the slot die would cause the fibers at different positions to bear inconsistent air force. The air velocity of the spinning centerline is higher than that around it, which is more conducive to fiber diameter attenuation. The violent fluctuation of the instantaneous velocity of the airflow could easily cause the meltblowing fiber to whip in the area close to the die.

Hydroclimatic Response of Watersheds to Urban Intensity: An Observational and Modeling-Based Analysis for the White River Basin, Indiana

2010 ◽  
Vol 11 (1) ◽  
pp. 122-138 ◽  
Author(s):  
Guoxiang Yang ◽  
Laura C. Bowling ◽  
Keith A. Cherkauer ◽  
Bryan C. Pijanowski ◽  
Dev Niyogi
Keyword(s):  
River Basin ◽  
Land Surface ◽  
Great Influence ◽  
Flow Distribution ◽  
Surface Characteristics ◽  
Infiltration Capacity ◽  
Vic Model ◽  
White River ◽  
Urban Model ◽  
Streamflow Regime

Abstract Impervious surface area (ISA) has different surface characteristics from the natural land cover and has great influence on watershed hydrology. To assess the urbanization effects on streamflow regimes, the authors analyzed the U.S. Geological Survey (USGS) streamflow data of 16 small watersheds in the White River [Indiana (IN)] basin. Correlation between hydrologic metrics (flow distribution, daily variation in streamflow, and frequency of high-flow events) and ISA was investigated by employing the nonparametric Mann–Kendall method. Results derived from the 16 watersheds show that urban intensity has a significant effect on all three hydrologic metrics. The Variable Infiltration Capacity (VIC) model was modified to represent ISA in urbanized basins using a bulk parameterization approach. The model was then applied to the White River basin to investigate the potential ability to simulate the water and energy cycle response to urbanization. Correlation analysis for individual VIC grid cells indicates that the VIC urban model was able to reproduce the slope magnitude and mean value of the USGS streamflow metrics. The urban model also reproduced the urban heat island (UHI) seen in the Moderate Resolution Imaging Spectroradiometer (MODIS) land surface temperature products, especially for the grids encompassing the city of Indianapolis, IN. The difference of the hydrologic metrics obtained from the VIC model with and without urban representation indicates that the streamflow regime in the White River has been modified because of urban development. The observed data, together with model analysis, suggested that 3%–5% ISA in a watershed is the detectable threshold, beyond which urbanization effects start to have a statistically significant influence on streamflow regime.

The Performance Analysis and Experimental Research of Multiple Oil Ports Axial Piston Pump which Able to Control the Movement of Differential Cylinder Directly in the Closed Circuit

2011 ◽  
Vol 308-310 ◽  
pp. 388-400
Author(s):  
Xiao Gang Zhang ◽  
Long Quan
Keyword(s):  
Digital Simulation ◽  
Flow Distribution ◽  
Closed Circuit ◽  
Piston Pump ◽  
Distribution Area ◽  
Axial Piston Pump ◽  
Hydraulic Pump ◽  
Asymmetric Flow ◽  
New Type ◽  
Axial Piston

In order to realize that an asymmetric flow piston pump can control an asymmetric differential cylinder, a proposal about the application of an asymmetric flow-distributing axial piston pump is put forward. The new type of piston pump can output the flows with two different values to control the movement of the differential cylinder directly in the closed circuit and realize much ideal result of the control of the differential cylinder by a single pump. Also a simulation model of the hydraulic pump is established under the circumstance of SimulationX software, considering the characteristics of the movement of an individual piston, the oil compressibility, and the flow distribution area changed with the rotation angle. The key data of the pump is defined by means of digital simulation. In particular, an analysis is made on the dimension of the unloading groove of the port plate and the characteristics of the flow pulse of the pump. Furthermore, an experimental model pump is manufactured, the basic performances of the pump is tested on the experimental platform at various rotatory speeds such as pressure, flow and noise, in the end the accuracy of the principle is verified.

scholarly journals Acousto-Optic Cells with Phased-Array Transducers and Their Application in Systems of Optical Information Processing

Materials ◽  
2021 ◽  
Vol 14 (2) ◽  
pp. 451
Author(s):  
Vladimir Balakshy ◽  
Maxim Kupreychik ◽  
Sergey Mantsevich ◽  
Vladimir Molchanov
Keyword(s):  
Phased Array ◽  
Power Conversion ◽  
Experimental Studies ◽  
Acoustic Power ◽  
Acoustic Mode ◽  
Bragg Angle ◽  
Excitation Band ◽  
Acousto Optic Interaction ◽  
Array Transducer ◽  
New Type

This paper presents the results of theoretical and experimental studies of anisotropic acousto-optic interaction in a spatially periodical acoustic field created by a phased-array transducer with antiphase excitation of adjacent sections. In this case, contrary to the nonsectioned transducer, light diffraction is absent when the optical beam falls on the phased-array cell at the Bragg angle. However, the diffraction takes place at some other angles (called “optimal” here), which are situated on the opposite sides to the Bragg angle. Our calculations show that the diffraction efficiency can reach 100% at these optimal angles in spite of a noticeable acousto-optic phase mismatch. This kind of acousto-optic interaction possesses a number of interesting regularities which can be useful for designing acousto-optic devices of a new type. Our experiments were performed with a paratellurite (TeO2) cell in which a shear acoustic mode was excited at a 9∘ angle to the crystal plane (001). The piezoelectric transducer had to nine antiphase sections. The efficiency of electric to acoustic power conversion was 99% at the maximum frequency response, and the ultrasound excitation band extended from 70 to 160 MHz. The experiments have confirmed basic results of the theoretical analysis.

Numerical Investigation of an Asymmetric Double Suction Centrifugal Compressor With Different Backswept Angle Matching for a Wide Operating Range

2017 ◽  
Author(s):  
Hanzhi Zhang ◽  
Dazhong Lao ◽  
Longyu Wei ◽  
Ce Yang ◽  
Mingxu Qi
Keyword(s):  
Mass Flow ◽  
Centrifugal Compressor ◽  
Flow Distribution ◽  
Operating Mode ◽  
Mode Transition ◽  
Distribution Characteristics ◽  
Operating Range ◽  
Stable Operating ◽  
Angle Difference ◽  
Matching Models

The work presented here investigates the characteristics of the different impeller backswept angle matchings for a wide stable operating range in an asymmetric double suction centrifugal compressor. The numerical simulation was employed to investigate the influence of different backswept angle matchings on the stable operating range. The aim is to propose a proper change of the backswept angle matching between two impeller sides to improve the impeller power capability and mass flow distribution, furthermore, to delay the operating mode transition and widen the stable operating range of the compressor. Firstly, the method to determine the optimum backswept angle matching obtained by the theory calculation. Then, three matching models were proposed and analyzed in detail. In three matching models, the backswept angle differences between the front and rear impeller side are 0°, 10° and 20°, respectively. The analysis mainly focused on the influence of the different backswept angle matchings on the compressor flow field characteristics and the mass flow distribution characteristics. The results show that the change of the impeller backswept angle matching can improve the mass flow distribution characteristics for two impeller sides and further reduce the stall mass flow rate of the double suction compressor. The model that the backswept angle difference is 10° can delay the operating mode transition and reduce the stall mass flow of the double suction compressor. The model that the backswept angle difference is 20° can also reduce the stall mass flow and finally enable the front impeller into the stall condition. Therefore, the proper change of the backswept angle matching can achieve the purpose of reducing the stall mass flow and widening the operating range for the double suction centrifugal compressor.

scholarly journals Enhancement of Exit Flow Uniformity by Modifying the Shape of a Gas Torch to Obtain a Uniform Temperature Distribution on a Steel Plate during Preheating

2018 ◽  
Vol 8 (11) ◽  
pp. 2197
Author(s):  
Thien Ngo ◽  
Junho Go ◽  
Tianjun Zhou ◽  
Hap Nguyen ◽  
Geun Lee
Keyword(s):  
Temperature Distribution ◽  
Temperature Difference ◽  
Steel Plate ◽  
Flow Distribution ◽  
Uniform Temperature ◽  
Flow Uniformity ◽  
Modified Model ◽  
Uniform Temperature Distribution ◽  
Basic Model ◽  
New Models

The objective of this study is to improve the exit flow uniformity of a gas torch with multiple exit holes for effective heating of a steel plate. The torch was simulated, and combustion experiments were performed for validation. Based on a basic model, three different revised models were designed and analyzed with the software ANSYS FLUENT 18.2. The flow uniformity (γ) of the velocity distribution at the multiple exit holes was investigated with the pressure drop ranging from 100 to 500 Pa. The basic model had flow uniformity ranging from 0.849 to 0.852, but the three new models had γ1 = 0.901–0.912, γ2 = 0.902–0.911, and γ3 = 0.901–0.914, respectively. The maximum percentage difference of the flow uniformity index between the three new models and the basic model was 7.3%. The basic model with nonuniform flow distribution made a temperature difference of the back side of the steel plate from the center to the edge of around 229 °C, while the modified model with uniform flow distribution had a smaller temperature difference of 90 °C. The simulation results showed good agreement with our experimental results for both the basic model and the modified model. The modified gas torch made a wider and more uniform temperature distribution on a preheated steel plate than the basic one. The results revealed that a trade-off between cost and flow uniformity, as well as the new gas torch, could be applied to a steel-plate preheating process before welding.

scholarly journals Falling weight impact test of a new-type flexible rock-shed

2018 ◽  
Vol 38 (2) ◽  
pp. 242-252
Author(s):  
Jianrong Yang ◽  
Zhiyu Zhang
Keyword(s):  
Experimental Studies ◽  
Steel Tube ◽  
Time Interval ◽  
Explicit Finite Element ◽  
Numerical Studies ◽  
Structural Details ◽  
Tensile Forces ◽  
New Type ◽  
Falling Weight ◽  
The Impact

A new concept of a flexible rock-shed is presented for protection of the railway from falling rocks. The flexible rock-shed is made of flexible nets connected by specific spring spacer bars to an array of reinforced concrete portable frames which are linked by a longitudinal steel tube truss. To evaluate the performance of the flexible rock-shed, experimental and numerical studies are carried out in the present study. Impact tests are conducted on a full-scale partial model of the prototype structure when it is subjected to a falling block of 340 kg. The impact time interval, maximum deflection of the flexible net, tensile forces in the supporting ropes, and axial strains of spring spacer bars are recorded. To further examine the dynamic behavior of the flexible rock-shed, numerical simulations are also carried out by using the explicit finite element code ANSYS/LS-DYNA. It is found that the numerical results coincide well with the experimental data and both the numerical and experimental studies reveal that the structure can withstand impact energy of 50 kJ with all the materials working in the elastic range. The structural details are improved and the basis for the design and construction of similar structures in the future is provided.<br>

Sign in / Sign up

Export Citation Format

Share Document