scholarly journals Cyanide Removal and Recovery by Electrochemical Crystallization Process

Water ◽  
2021 ◽  
Vol 13 (19) ◽  
pp. 2704
Author(s):  
Natacha Martin ◽  
Vinh Ya ◽  
Vincenzo Naddeo ◽  
Kwang-Ho Choo ◽  
Chi-Wang Li

Alkaline chlorination, an efficient but high chemical cost process, is commonly employed for cyanide (CN−) removal from CN-rich wastewater streams. CN− removal and recovery through the precipitation of Prussian Blue (Fe4III[FeII(CN)6]3, PB) or Turnbull’s Blue (Fe3II[FeIII(CN)6]2, TB) were realized using iron salts, leading to a cost-effective and sustainable process producing a valuable recovery product. However, the precipitation of PB and TB is highly affected by pH and dissolved oxygen (DO). CN− removal and recovery from CN-containing water by crystallization of PB and/or TB were investigated using dissolved iron that was electrochemically generated from a sacrificial iron anode under various pH values, initial CN− levels (10 to100 mg/L) and DO levels (aeration, mechanical mixing, and N2 purging). It was shown that the complexation of CN− with Fe ions prevented the vaporization of HCN under acidic pH. At pH of 7 and initial CN− concentration of 10 mg/L, CN− removal efficiency increases linearly with increasing Fe:CN− molar ratios, reaching 80% at the Fe:CN− molar ratio of 5. A clear blue precipitate was observed between the pH range of 5–7. CN− removal increases with increasing initial CN− concentration, resulting in residual CN− concentrations of 8, 7.5 and 12 mg/L in the effluent with the Fe:CN− molar ratio of 0.8 for initial concentrations of 10, 50 and 100 mg CN−/L, respectively. A polishing treatment with H2O2 oxidation was employed to lower the residual CN− concentration to meet the discharge limit of <1 mg CN−/L.

2010 ◽  
Vol 75 (2) ◽  
pp. 165-173 ◽  
Author(s):  
Muhammad Hussain ◽  
Dure Shahwar ◽  
Muhammad Tahir ◽  
Muhammad Sher ◽  
Muhammad Hassan ◽  
...  

A facile, efficient, cost-effective and solvent-free acetylation method has been developed for the acetylation of dextran. Dextran acetates were successfully synthesized using different molar ratios of acetic anhydride in the presence of iodine as a catalyst without the use of any solvent. The reactions were realized at 50?C for 3 h under stirring and nitrogen. This efficient method yielded highly pure and organosoluble dextran esters. The reaction appears highly effective for obtaining higher degrees of substitution (DS) with great efficiency. Under solvent-free conditions, dextran triacetates were efficiently synthesized. It was also observed that the molar ratio can easily control the DS of pendant groups onto the polymer backbone. Hence, a range of products with varying DS were successfully designed, purified and characterized. Covalent attachment of the pendant groups onto the polymer backbone was verified by spectroscopic techniques. Thermogravimetric analysis indicated that the obtained dextran esters were thermally as stable as dextran. The DS of the pendant groups onto the polymer backbone was calculated using standard acid base titration after saponification. Furthermore, all products were thoroughly characterized by thermal analysis (TG and DTG), and FTIR and 1H-NMR spectroscopic analysis.


2009 ◽  
Vol 7 (3) ◽  
pp. 423-428 ◽  
Author(s):  
Melda Altikatoglu ◽  
Candan Arioz ◽  
Yeliz Basaran ◽  
Huriye Kuzu

AbstractStabilization of Horseradish Peroxidase (HRP; EC 1.11.1.7) against temperature and pH via the formation of the conjugates obtained by multipoint covalent bonding of dextran aldehyde (DA) to the enzyme were studied. Hence, three different molar weighted dextrans (17.5 kD, 75 kD, 188 kD) were covalently bonded to purified enzyme with different molar ratios (nHRP/nDA 20/1, 10/1, 1/1, 1/5, 1/10, 1/15, 1/20). The thermal stabilities of the obtained conjugates were evaluated with the activities determined at different temperatures (25, 30, 35, 40, 50, 60, 70, 80°C) applying 60 minutes incubation time. Conjugates formed were characterized by gel-permeation chromatography (GPC) and fluorescence techniques. The conjugate synthesized using dextran 75 kDa with nHRP/nDA 1/10 molar ratio showed better thermal stability than other conjugates and purified enzyme at pH 7. This conjugate also has wider activity pH range than purified enzyme. In addition, mentioned conjugate at pH 7 had very long storage lifetime compared to purified enzyme at +4°C and room temperature; which is considered a favorable feature for usage in practice.


2012 ◽  
Vol 10 (10) ◽  
pp. 33-37 ◽  
Author(s):  
G Gyawali ◽  
A Rajbhandari (Nyachhyon)

Polyaluminium silicate chloride (PASiC) coagulant was synthesized by co-polymerization technique using aluminium salt and polysilicic acid at different OH/Al and Al/Si molar ratios. A synthetic turbid sample was used to investigate the coagulation efficiency of the prepared coagulant. After the coagulant dosing, flocculation time was set for 15 minutes followed by sedimentation for 20 minutes.  High performance of coagulant was achieved at 2.5 molar ratio of OH/Al and 5 molar ratio of Al/Si at the optimal pH. The optimum pH range was found to be 7±0.5.The effective coagulant dose for the efficient removal of turbidity was set as 2.5 mg/L. As compared to conventional alum, PASiC has been found to be excellent inorganic polymeric coagulant for turbidity removal from water and residual aluminum was found to be minimal in comparison to conventional alum treatment. Hence, PASiC has proven the potentiality for the turbidity removal in water treatment over conventional alum. Scientific World, Vol. 10, No. 10, July 2012 p33-37 DOI: http://dx.doi.org/10.3126/sw.v10i10.6859


Catalysts ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 346
Author(s):  
Sonam Goyal ◽  
Maizatul Shima Shaharun ◽  
Ganaga Suriya Jayabal ◽  
Chong Fai Kait ◽  
Bawadi Abdullah ◽  
...  

A set of novel photocatalysts, i.e., copper-zirconia imidazolate (CuZrIm) frameworks, were synthesized using different zirconia molar ratios (i.e., 0.5, 1, and 1.5 mmol). The photoreduction process of CO2 to methanol in a continuous-flow stirred photoreactor at pressure and temperature of 1 atm and 25 °C, respectively, was studied. The physicochemical properties of the synthesized catalysts were studied using X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and photoluminescence (PL) spectroscopy. The highest methanol activity of 818.59 µmol/L.g was recorded when the CuZrIm1 catalyst with Cu/Zr/Im/NH4OH molar ratio of 2:1:4:2 (mmol/mmol/mmol/M) was employed. The enhanced yield is attributed to the presence of Cu2+ oxidation state and the uniformly dispersed active metals. The response surface methodology (RSM) was used to optimize the reaction parameters. The predicted results agreed well with the experimental ones with the correlation coefficient (R2) of 0.99. The optimization results showed that the highest methanol activity of 1054 µmol/L.g was recorded when the optimum parameters were employed, i.e., stirring rate (540 rpm), intensity of light (275 W/m2) and photocatalyst loading (1.3 g/L). The redox potential value for the CuZrIm1 shows that the reduction potential is −1.70 V and the oxidation potential is +1.28 V for the photoreduction of CO2 to methanol. The current work has established the potential utilization of the imidazolate framework as catalyst support for the photoreduction of CO2 to methanol.


Molecules ◽  
2021 ◽  
Vol 26 (11) ◽  
pp. 3317
Author(s):  
Maria Carolina Pereira Gonçalves ◽  
Jéssica Cristina Amaral ◽  
Roberto Fernandez-Lafuente ◽  
Ruy de Sousa Junior ◽  
Paulo Waldir Tardioli

In this paper, we have performed the Lipozyme 435-catalyzed synthesis of xylose oleate in methyl ethyl ketone (MEK) from xylose and oleic acid. The effects of substrates’ molar ratios, reaction temperature, reaction time on esterification rates, and Lipozyme 435 reuse were studied. Results showed that an excess of oleic acid (xylose: oleic acid molar ratio of 1:5) significantly favored the reaction, yielding 98% of xylose conversion and 31% oleic acid conversion after 24 h-reaction (mainly to xylose mono- and dioleate, as confirmed by mass spectrometry). The highest Lipozyme 435 activities occurred between 55 and 70 °C. The predicted Ping Pong Bi Bi kinetic model fitted very well to the experimental data and there was no evidence of inhibitions in the range assessed. The reaction product was purified and presented an emulsion capacity close to that of a commercial sugar ester detergent. Finally, the repeated use of Lipozyme 435 showed a reduction in the reaction yields (by 48 and 19% in the xylose and oleic acid conversions, respectively), after ten 12 h-cycles.


Catalysts ◽  
2020 ◽  
Vol 10 (4) ◽  
pp. 427 ◽  
Author(s):  
Muhammad Awais ◽  
Sa’ed A Musmar ◽  
Faryal Kabir ◽  
Iram Batool ◽  
Muhammad Asif Rasheed ◽  
...  

Biodiesel is a renewable fuel usually produced from vegetable oils and animal fats. This study investigates the extraction of oil and its conversion into biodiesel by base-catalyzed transesterification. Firstly, the effect of various solvents (methanol, n-hexane, chloroform, di-ethyl ether) on extraction of oil from non-edible crops, such as R. communis and M. azedarach, were examined. It was observed that a higher concentration of oil was obtained from R. communis (43.6%) as compared to M. azedarach (35.6%) by using methanol and n-hexane, respectively. The extracted oils were subjected to NaOH (1%) catalyzed transesterification by analyzing the effect of oil/methanol molar ratio (1:4, 1:6, 1:8 and 1:10) and varying temperature (20, 40, 60 and 80 °C) for 2.5 h of reaction time. M. azedarach yielded 88% and R. communis yielded 93% biodiesel in 1:6 and 1:8 molar concentrations at ambient temperature whereas, 60 °C was selected as an optimum temperature, giving 90% (M. azedarach) and 94% (R. communis) biodiesel. The extracted oil and biodiesel were characterized for various parameters and most of the properties fulfilled the American Society for Testing and Materials (ASTM) standard biodiesel. The further characterization of fatty acids was done by Gas Chromatography/Mass Spectrometer (GC/MS) and oleic acid was found to be dominant in M. azedarach (61.5%) and R. communis contained ricinoleic acid (75.53%). Furthermore, the functional groups were analyzed by Fourier Transform Infrared Spectroscopy. The results suggested that both of the oils are easily available and can be used for commercial biodiesel production at a cost-effective scale.


Holzforschung ◽  
2014 ◽  
Vol 68 (4) ◽  
pp. 477-486 ◽  
Author(s):  
Myung Jae Lee ◽  
Sedric Pankras ◽  
Paul Cooper

Abstract Canadian refractory wood species treated with micronized copper (MCu) wood preservative become mottled and streaky in appearance. To overcome this issue, the MCu system was modified by adding small amounts of monoethanolamine (Mea). The modified systems were evaluated to clarify the role of Mea in terms of leaching, corrosion, and mold resistance of MCu systems. The mottled and streaky surface on treated spruce was prevented at Mea/Cu molar ratios between 0.7 and 1.5. Copper leaching remained modest and was only slightly higher than that of MCu alone up to a Mea/Cu molar ratio of 1.2. However, adding even a small amount of Mea to the MCu formulation increased fastener corrosion compared with MCu. Protonated Mea increased as more Mea was added and was identified as the main corrosion-causing electrolyte in the system.


RSC Advances ◽  
2016 ◽  
Vol 6 (38) ◽  
pp. 32319-32327 ◽  
Author(s):  
Chun-Chieh Han ◽  
Yu-Chaing Chou ◽  
San-Yuan Chen ◽  
Hong-Cheu Lin

The molar ratio, alkyl chain length, lateral fluoro-substitution and the chiral center of H-bonded bent-core supramolecules would affect the BP ranges of BPLC complexes. H-bonded bent-core complex PIIIC9/AIIF* (3/7 mol mol−1) displayed the widest BPI range of ΔTBPI = 12 °C.


2013 ◽  
Vol 5 (2) ◽  
pp. 1845-1870 ◽  
Author(s):  
P. Lübcke ◽  
N. Bobrowski ◽  
S. Arellano ◽  
B. Galle ◽  
G. Garzón ◽  
...  

Abstract. The molar ratio of BrO to SO2 is, like other halogen/sulphur ratios, a~possible precursor for dynamic changes in the shallow part of a volcanic system. While the predictive significance of the BrO/SO2 ratio has not been well constrained yet, it has the major advantage that this ratio can be readily measured using the remote-sensing technique Differential Optical Absorption Spectroscopy (DOAS) in the UV. While BrO/SO2 ratios have been measured during several short-term field campaigns this article presents an algorithm that can be used to obtain long-term time series of BrO/SO2 ratios from the scanning DOAS instruments of the Network for Observation of Volcanic and Atmospheric Change (NOVAC) or comparable networks. Parameters of the DOAS retrieval of both trace gases are given and the influence of co-adding spectra on the retrieval error will be investigated. Difficulties in the evaluation of spectroscopic data from monitoring instruments in volcanic environments and possible solutions are discussed. The new algorithm is demonstrated by evaluating data from the NOVAC scanning DOAS systems at Nevado del Ruiz, Colombia encompassing almost four years of measurements between November 2009 and end of June 2013. This dataset shows variations of the BrO/SO2 ratio several weeks prior to the eruption on 30 June 2012.


1982 ◽  
Vol 152 (2) ◽  
pp. 888-892
Author(s):  
S Rottem ◽  
R M Cole ◽  
W H Habig ◽  
M F Barile ◽  
M C Hardegree

Tetanolysin binding to lipid vesicles was found to depend on the molar ratio of cholesterol to phospholipid, being low in vesicles containing up to 20 mol% cholesterol and high in vesicles containing more than 33 mol%. High concentrations of purified tetanolysin preparations formed arc- and ring-shaped structures. The structures were not readily detectable in diluted preparations unless incubated with lipid vesicles containing high molar ratios of cholesterol to phospholipid. It is suggested that the toxin is concentrated on the vesicles to local concentrations high enough to form the arcs and rings.


Sign in / Sign up

Export Citation Format

Share Document