scholarly journals Nitrate Removal Performance of Denitrifying Woodchip Bioreactors in Tropical Climates

Water ◽  
2021 ◽  
Vol 13 (24) ◽  
pp. 3608
Author(s):  
Fabio Manca ◽  
Carla Wegscheidl ◽  
Rhianna Robinson ◽  
Suzette Argent ◽  
Christopher Algar ◽  
...  

In Australia, declining water quality in the Great Barrier Reef (GBR) is a threat to its marine ecosystems and nitrate (NO3−) from sugar cane-dominated agricultural areas in the coastal catchments of North Queensland is a key pollutant of concern. Woodchip bioreactors have been identified as a potential low-cost remediation technology to reduce the NO3− runoff from sugar cane farms. This study aimed to trial different designs of bioreactors (denitrification walls and beds) to quantify their NO3− removal performance in the distinct tropical climates and hydrological regimes that characterize sugarcane farms in North Queensland. One denitrification wall and two denitrification beds were installed to treat groundwater and subsurface tile-drainage water in wet tropics catchments, where sugar cane farming relies only on rainfall for crop growth. Two denitrification beds were installed in the dry tropics to assess their performance in treating irrigation tailwater from sugarcane. All trialled bioreactors were effective at removing NO3−, with the beds exhibiting a higher NO3− removal rate (NRR, from 2.5 to 7.1 g N m−3 d−1) compared to the wall (0.15 g N m−3 d−1). The NRR depended on the influent NO3− concentration, as low influent concentrations triggered NO3− limitation. The highest NRR was observed in a bed installed in the dry tropics, with relatively high and consistent NO3− influent concentrations due to the use of groundwater, with elevated NO3−, for irrigation. This study demonstrates that bioreactors can be a useful edge-of-field technology for reducing NO3− in runoff to the GBR, when sited and designed to maximise NO3− removal performance.

Water ◽  
2021 ◽  
Vol 13 (13) ◽  
pp. 1732
Author(s):  
Yuanyuan Yu ◽  
Yongjun Sun ◽  
Jun Zhou ◽  
Aowen Chen ◽  
Kinjal J. Shah

In this study, a high-efficiency magnetic heavy metal flocculant MF@AA was prepared based on carboxymethyl chitosan and magnetic Fe3O4. It was characterized by SEM, FTIR, XPS, XRD and VSM, and the Cu(II) removal rate was used as the evaluation basis for the preparation process. The effects of AMPS content, total monomer concentration, photoinitiator concentration and reaction time on the performance of MF@AA flocculation to remove Cu(II) were studied. The characterization results show that MF@AA has been successfully prepared and exhibits good magnetic induction characteristics. The synthesis results show that under the conditions of 10% AMPS content, 35% total monomer concentration, 0.04% photoinitiator concentration, and 1.5 h reaction time, the best yield of MF@AA is 77.69%. The best removal rate is 87.65%. In addition, the response surface optimization of the synthesis process of MF@AA was performed. The optimal synthesis ratio was finally determined as iron content 6.5%, CMFS: 29.5%, AM: 53.9%, AMPS: 10.1%. High-efficiency magnetic heavy metal flocculant MF@AA shows excellent flocculation performance in removing Cu(II). This research provides guidance and ideas for the development of efficient and low-cost flocculation technology to remove Cu(II) in wastewater.


2019 ◽  
Vol 17 (1) ◽  
pp. 1173-1184 ◽  
Author(s):  
Fengyun Tao ◽  
Yangping Liu ◽  
Junliang Chen ◽  
Peng Wang ◽  
Qing Huo

AbstractThe disposal of residues while manufacturing Chinese medicine has always been an issue that concerns pharmaceutical factories. Phanerochaete chrysosporium was inoculated into the residues of Magnolia officinalis for solid-phase fermentation to enzymatically hydrolyze the lignin in the residues and thus to improve the efficiency of removal of the copper ions from residues for the utilization of residues from Chinese medicine. With the increase in activities of lignin-degrading enzymes, especially during the fermentation days 6 to 9, the removal rate of copper ions using M. officinalis residues increased dramatically. The rate of removal reached the maximum on the 14th day and was 3.15 times higher than the initial value. The rate of adsorption of copper ions on the fermentation-modified M. officinalis residues followed the pseudo-second-order kinetics. The adsorption isotherms were consistent with the Freundlich models. The adsorption enthalpy was positive, indicating that it was endothermic and elevation in temperature was favorable to this adsorption process. The adsorption free energy was negative, implying the spontaneity of the process. The copper ions adsorbed could be effectively recovered using 0.2 M hydrochloric acid solution. After five successive cycles of adsorption-regeneration, the fermentation-modified M. officinalis residues exhibited a stable adsorption capacity and greater reusability. The M. officinalis residues fermented with P. chrysosporium are low-cost and environmentally friendly copper ions adsorbent, and this preparation technique realizes the optimum utilization of Chinese medicine residues.


2016 ◽  
Author(s):  
A. Ribeiro ◽  
C. Vilarinho ◽  
J. Araújo ◽  
J. Carvalho

The increasing of world population, industrialization and global consuming, existing market products existed in the along with diversification of raw materials, are responsible for an exponential increase of wastes. This scenario represents loss of resources and ultimately causes air, soils and water pollution. Therefore, proper waste management is currently one of the major challenges faced by modern societies. Textile industries represents, in Portugal, almost 10% of total productive transforming sector and 19% of total employments in the sector composed by almost 7.000 companies. One of the main environmental problems of textile industries is the production of significant quantities of wastes from its different processing steps. According to the Portuguese Institute of Statistics (INE) these industries produce almost 500.000 tons of wastes each year, with the textile cotton waste (TCW) being the most expressive. It was estimated that 4.000 tons of TCW are produced each year in Portugal. In this work an integrated TCW valorisation procedure was evaluated, firstly by its thermal and energetic valorisation with slow pyrolysis followed by the utilization of biochar by-product, in lead and chromium synthetic wastewater decontamination. Pyrolysis experiments were conducted in a small scale rotating pyrolysis reactor with 0.1 m3 of total capacity. Results of pyrolysis experiments showed the formation of 0,241 m3 of biogas for each kilogram of TCW. Results also demonstrated that the biogas is mostly composed by hydrogen (22%), methane (14 %), carbon monoxide (20%) and carbon dioxide (12%), which represents a total high calorific value of 12.3 MJ/Nm3. Regarding biochar, results of elemental analysis demonstrated a high percentage of carbon driving its use as low cost adsorbent. Adsorption experiments were conducted with lead and chromium synthetic wastewaters (25, 50 and 100 mg L−1) in batch vessels with controlled pH. It was evaluated the behaviour of adsorption capacity and removal rate of each metal during 120 minutes of contact time using 5, 10 and 50 g L−1 of adsorbent dosage. Results indicated high affinity of adsorbent with each tested metal with 78% of removal rate in chromium and 95% in lead experiments. This suggests that biochar from TCW pyrolysis may be appropriated to wastewaters treatment, with high contents of heavy metals and it can be an effective alternative to activated carbon.


2010 ◽  
Author(s):  
Seyyed Ebrahim Hashemi ◽  
Manouchehr Heidarpour ◽  
Behrouz Mostafazadeh-Fard ◽  
Ali Madani ◽  
Sayed-Farhad Mousavi ◽  
...  

2013 ◽  
Vol 67 (2) ◽  
pp. 340-346 ◽  
Author(s):  
Y. H. Ong ◽  
A. S. M. Chua ◽  
B. P. Lee ◽  
G. C. Ngoh

To date, little information is known about the operation of the enhanced biological phosphorus removal (EBPR) process in tropical climates. Along with the global concerns on nutrient pollution and the increasing array of local regulatory requirements, the applicability and compliance accountability of the EBPR process for sewage treatment in tropical climates is being evaluated. A sequencing batch reactor (SBR) inoculated with seed sludge from a conventional activated sludge (CAS) process was successfully acclimatized to EBPR conditions at 28 °C after 13 days' operation. Enrichment of Candidatus Accumulibacter phosphatis in the SBR was confirmed through fluorescence in situ hybridization (FISH). The effects of operational pH and influent C:P ratio on EBPR were then investigated. At pH 7 or pH 8, phosphorus removal rates of the EBPR processes were relatively higher when operated at C:P ratio of 3 than C:P ratio of 10, with 0.019–0.020 and 0.011–0.012 g-P/g-MLVSS•day respectively. One-year operation of the 28 °C EBPR process at C:P ratio of 3 and pH 8 demonstrated stable phosphorus removal rate of 0.020 ± 0.003 g-P/g-MLVSS•day, corresponding to effluent with phosphorus concentration <0.5 mg/L. This study provides the first evidence on good EBPR activity at relatively high temperature, indicating its applicability in a tropical climate.


2021 ◽  
Vol 21 (7) ◽  
pp. 3882-3886
Author(s):  
Yong-Wook Jung ◽  
Jong Kyu Kim

In this study, nano-sized low cost titanium dioxide (TFS) was prepared using sludge from sewage treatment and performance was verified. To remove air pollutants, the photocatalytic degradation of methylene blue and efflorescence characteristics is assessed according to the mixing ratio of the nano-sized TFS by applying them to concrete sidewalk blocks. The photocatalytic degradation performance of concrete sidewalk blocks shows that the methylene blue removal rate of specimens containing 2.5%, 5%, and 10% of nano-sized TFS is 29%, 27%, and 38%, respectively. When the nano-sized TFS is mingled on the surface of the sidewalk block, the performance of anti-corrosion and antifouling showed excellency mainly due to the moisture blocking derived by the antifouling function of photocatalysts.


2020 ◽  
Vol 993 ◽  
pp. 1445-1449
Author(s):  
Shi Jie Liu ◽  
Su Ping Cui ◽  
Hong Xia Guo ◽  
Ya Li Wang ◽  
Nan Li ◽  
...  

Calcium silicate hydrate gel (CSH) was synthesized by calcium acetate and sodium silicate. The structure and morphology of CSH were characterized by X-ray diffraction analysis, Fourier transform infrared spectroscopy and Scanning electron microscopy. The adsorption performance of CSH was measured by static adsorption method. The results show that CSH has porous structure and large specific surface area, and the optimum reaction conditions is the reaction temperature of 25°C and calcium-silicon ratio of 1.2. It has the maximum adsorption capacity of more than 150 mg/g and the removal rate of more than 86% with Cu2+. And it shows the excellent adsorption performance, even when the concentration of Cu2+ is less than 200mg/L, the removal rate is above 90%. The research may provide a low-cost and high-efficiency adsorbent.


Nanomaterials ◽  
2019 ◽  
Vol 9 (2) ◽  
pp. 265 ◽  
Author(s):  
Yi Wang ◽  
Weinan Zhao ◽  
Wanlan Zheng ◽  
Shuang Chen ◽  
Jinsheng Zhao

Porous activated carbon with specific morphology and structure are of particular importance for waste water treatment, especially for the adsorption of toxic hexavalent chromium Cr(VI). However, the scalable and cheap production of such absorbents still suffer a grand challenge. Herein, a new type of N-doped nanosheet was innovatively prepared from easily available and low-cost sewage sludge via a facile and recyclable KOH activation method. The N-doped porous carbon nanosheets (N-SAC) produced by introduction of KOH and dicyandiamide, which performed favourable features for metal ions adsorption (93.2% for Cr(VI)) due to its high specific surface area, tuneable pore size distributions and good hydrophilicity. Additionally, the capacity also remained high after two cycles of adsorption by thermal regeneration, with 90.8% removal rate. The DFT calculation also approved that the doping of N could optimize the Mulliken charges distribution and improve the HOMO energy and improve the adsorption ability of N-SAC. This original proposal may inspire new possibility of creating porous carbon absorbents in a recyclable method.


Sign in / Sign up

Export Citation Format

Share Document