scholarly journals Change in surface properties of tooth under cold atmospheric plasma impact

Doklady BGUIR ◽  
2020 ◽  
Vol 18 (8) ◽  
pp. 83-88
Author(s):  
A. V. Aksyuchits ◽  
D. A. Kotov ◽  
A. N. Osipov ◽  
V. Ch. Nedel
Keyword(s):  
Flow Rate ◽  
Atmospheric Pressure ◽  
Plasma Torch ◽  
Experimental Studies ◽  
Plasma Generator ◽  
Wetting Angle ◽  
Atmospheric Plasma ◽  
Tooth Surface ◽  
Surface Wetting ◽  
Water Wetting

The article presents the results of experimental studies of the wetting angle of the tooth surface after treatment in the plasma of a dielectric barrier discharge at atmospheric pressure. Measurements of the dependence of the length of the plasma torch and the temperature of the treatment object on the flow rate of the working gas have been carried out. Argon was used as a working gas. The research revealed the possibility to change the length of the plasma torch in the range from 9 mm to more than 25 mm and showed that the temperature of the treated tooth surface with an increase in flow rate from 40 degrees Celsius falls to 32 degrees Celsius. The distilled water wetting angle was determined by the lying drop method. Depending on the processing time, a decrease in the contact angle of the tooth surface wetting from the initial 77 to 20 degrees was observed. The modes of operation of the plasma generator in tooth surface treatment, which provide the best indicators of its wettability, have been determined.

Thermal characteristics of an arc column in the stabilization zone of an air-operated laminar plasma torch

2020 ◽  
Vol 6 ◽  
pp. 56-61
Author(s):  
A.M. Kruchinin ◽  
◽  
M.Ya. Pogrebissky ◽  
E.S. Ryazanova ◽  
A.Yu. Chursin ◽  
...  
Keyword(s):  
Plasma Torch ◽  
Discharge Channel ◽  
Experimental Studies ◽  
Engineering Application ◽  
Thermal Characteristics ◽  
Plasma Generator ◽  
Electric Arc ◽  
Mathematical Basis ◽  
Channel Diameter ◽  
Electric Arc Heating

The method of universal characteristics of an electric arc is described as a mathematical basis for the heat exchange model of an electric arc in the processes of electric arc heating in electrical engineering. Application of this method for calculation of the temperature characteristics of an arc column compressed by the walls of the discharge channel in the stabilization zone of a laminar plasma torch operating in air is considered. An example of the temperature profile calculation of a wall-stabilized arc for a plasma generator with a discharge channel diameter of 5 mm operating in air at an arc current of 60 A is presented. Calculated results are compared with the results of experimental studies of this plasma generator.

scholarly journals Formation of the Traffic Flow Rate under the Influence of Traffic Flow Concentration in Time at Controlled Intersections in Tyumen, Russian Federation

2021 ◽  
Vol 13 (15) ◽  
pp. 8324
Author(s):  
Viacheslav Morozov ◽  
Sergei Iarkov
Keyword(s):  
Traffic Flow ◽  
Flow Rate ◽  
Traffic Congestion ◽  
Traffic Management ◽  
System Analysis ◽  
Motor Vehicle ◽  
Experimental Studies ◽  
Transport Systems ◽  
Experiment Planning ◽  
Traffic Light

Present experience shows that it is impossible to solve the problem of traffic congestion without intelligent transport systems. Traffic management in many cities uses the data of detectors installed at controlled intersections. Further, to assess the traffic situation, the data on the traffic flow rate and its concentration are compared. Latest scientific studies propose a transition from spatial to temporal concentration. Therefore, the purpose of this work is to establish the regularities of the influence of traffic flow concentration in time on traffic flow rate at controlled city intersections. The methodological basis of this study was a systemic approach. Theoretical and experimental studies were based on the existing provisions of system analysis, traffic flow theory, experiment planning, impulses, probabilities, and mathematical statistics. Experimental data were obtained and processed using modern equipment and software: Traficam video detectors, SPECTR traffic light controller, Traficam Data Tool, SPECTR 2.0, AutoCad 2017, and STATISTICA 10. In the course of this study, the authors analyzed the dynamics of changes in the level of motorization, the structure of the motor vehicle fleet, and the dynamics of changes in the number of controlled intersections. As a result of theoretical studies, a hypothesis was put forward that the investigated process is described by a two-factor quadratic multiplicative model. Experimental studies determined the parameters of the developed model depending on the directions of traffic flow, and confirmed its adequacy according to Fisher’s criterion with a probability of at least 0.9. The results obtained can be used to control traffic flows at controlled city intersections.

Modeling of an AC Plasma Torch—Part II: Gasdynamic Pattern and Effect of Flow Rate

2021 ◽  
Vol 49 (3) ◽  
pp. 1023-1027
Author(s):  
Nikolay Y. Bykov ◽  
Nikita V. Obraztsov ◽  
Anton A. Kobelev ◽  
Alexander V. Surov
Keyword(s):  
Flow Rate ◽  
Plasma Torch

Lowtemperature plasma generator for effective processing of materials

2021 ◽  
Vol 77 (5) ◽  
pp. 587-592
Author(s):  
M. Kh. Gadzhiev ◽  
A. S. Tyuftyaev ◽  
Yu. M. Kulikov ◽  
M. A. Sargsyan ◽  
D. I. Yusupov ◽  
...  
Keyword(s):  
Low Temperature ◽  
Flow Rate ◽  
Gas Flow ◽  
Arc Discharge ◽  
Plasma Jet ◽  
Plasma Generator ◽  
Low Temperature Plasma ◽  
Temperature Plasma ◽  
High Enthalpy ◽  
High Resource

Low-temperature plasma is used in metallurgy for steel alloying by nitrogen, deoxidization of magnetic alloys, obtaining of steels with particularly low carbon content, metal cleaning of nonmetallic inclusions, desulfurization and other refining processes. The wide application of those technologies is restrained by absence of reliable generators of low-temperature plasma (GLP) with sufficient resource of continuous operation. As a result of studies, a universal generator of high-enthalpy plasma jet of various working gases was created. The generator has expanding channel of the output electrode with an efficiency of ~60 % for argon working gas and ~80% for nitrogen and air. It was shown that the developed generator of low-temperature plasma ensures formation of a weakly diverging (2α = 12°) plasma jet with a diameter D = 5–12 mm, an enthalpy of 5–50 kJ/g and a mass average temperature of 5–10 kK, at a full electric power of the arc discharge of 5–50 kW and a plasma-forming gas flow rate of 1–3 g/s. Results of the study of propane additions to the plasma-forming gas effect on the state of cathodes with inserts made of pure tungsten, lanthanum tungsten, and hafnium presented. It was shown that a small propane addition (1%) to the plasma-forming gas, results in reducing effect of the insert material. Study of the GLP operation at arc current 100A with addition to the working gas nitrogen maximum possible volume of propane, which don’t disturb stability of arc showed that for the developed plasma generator at the nitrogen flow rate ~0,45 g/s, the propane flow rate was ~0,33 g/s (not more than ~73 % of the plasma-forming gas). The created high-resource GLP with changeable electrodes enables to obtain at the exit a high-enthalpy plasma flow of various gases (argon, nitrogen, air) and can be a prototype of more powerful plasmotrons of various technological application, in particular for plasma metallurgy.

The Study of Fire-extinguishing Process of Modelled Fire Seats

2021 ◽  
pp. 57-62
Author(s):  
V.N. Bordakov ◽  
Keyword(s):  
Flow Rate ◽  
Experimental Studies ◽  
Physical Modelling ◽  
Specific Flow Rate ◽  
Specific Flow ◽  
Acceptable Error ◽  
Fire Extinguishing ◽  
Fire Zone ◽  
Analysis Of Results ◽  
Fire Extinguishers

Test-fires to determine fire-extinguishers’ efficiency for extinguishing B class fires are conducted by operators equipped with working clothes, which does not comply with the requirements of physical modelling. This is why the ranks of extinguished modelled seats are significantly overestimated. The quantitative results of fire seats’ extinguishing can be comparatively evaluated in accordance with the value of specific flow rate of a fire-extinguishing agent. As it was detected, the specific flow rate of a fire-extinguishing agent does not actually depend on the rank of modelled fire seat when extinguished by an operator wearing thermal-protective clothes. At the same time, it is increasing along with the expansion of the fire zone scale in case the fire is extinguished without special protective clothes. Consequently, to increase the fire-extinguisher’s efficiency data reliability, the certifying tests should be conducted in conditions close to the real application conditions when the first person to firefight is not equipped with such special protective clothes. The experimental studies to determine the specific flow rate of a fire-extinguishing agent used modelled fire seats of various ranks. The analysis of results showed that the fire-extinguishers ensuring generation of drops of prevailing size more than 0,5 mm are required to extinguish the modelled sire seats. The degree of increasing flow rate for the fire-extinguishing agent to eliminate a fire and observation of a safe distance from the flame for an operator are conditioned by the scale of fire zone and affect the specific flow rate of agent required to ensure stable fire-extinguishing. Based on the results of extinguishing the fire seats «34В» or «55В», it is demonstrated that via using a correction factor it is possible, assuming an acceptable error, to evaluate the flow rate of fire-extinguishing agent to extinguish a modelled fire seat of any rank.

Effect Of The Rib Inclination Angle On Liquid Film Spreading Over The Structured Surface

2015 ◽  
Vol 10 (1) ◽  
pp. 42-49
Author(s):  
Aleksandr Pavlenko ◽  
Oleg Volodin ◽  
Vladimir Serdyukov
Keyword(s):  
Liquid Film ◽  
Flow Rate ◽  
Inclination Angle ◽  
High Speed ◽  
Film Flow ◽  
Complex Geometry ◽  
Experimental Studies ◽  
Local Flow ◽  
Structured Packing ◽  
Film Spreading

Results of experimental studies on hydrodynamics of the film flow of liquid nitrogen over the surface of the single elements of structured packing are presented. The effect of inclination angle of the large ribs and perforation on the zones of liquid film spreading over the corrugated surface with microtexture at different Reynolds numbers of the film is shown based on a comparison of experimental data. It is shown that the angle of large rib inclination has a significant influence on redistribution of the local flow rate of liquid flowing on the surface with complex geometry. Analysis of results of the high-speed video revealed that in a vicinity of the vertical lateral edges of corrugated plates, the intense rivulet flows are formed, including those with separation from the film flow surface. This negative factor can lead to significant liquid accumulation and flow near the vertical edges of the structured packing and on the inner wall of the heat exchanging apparatuses and, finally, to a significant increase in the degree of maldistribution of local liquid flow rate over the crosssection, for instance, of the distillation columns.

Effect of Blade Aspiration Slot Configuration on the Aerodynamic Performance of a Highly Loaded Aspirated Compressor Cascade

2017 ◽  
Author(s):  
Longxin Zhang ◽  
Le Cai ◽  
Bao Liu ◽  
Jun Ding ◽  
Songtao Wang
Keyword(s):  
Flow Control ◽  
Flow Rate ◽  
Control Method ◽  
Active Flow Control ◽  
Experimental Studies ◽  
Aerodynamic Performance ◽  
Flow Path ◽  
Compressor Cascade ◽  
Flow Loss ◽  
Highly Loaded

As a promising active flow control method, boundary layer suction (BLS) can be used to enhance the aerodynamic performance of the highly-loaded compressor effectively, and due to this reason, extensive studies have been carried out on it. However, contrast to those abundant studies focusing on the flow control effects of BLS, little attention has been paid on the design method of the aspiration flow path. This work presents a 3-D steady numerical simulation on a highly-loaded aspirated compressor cascade. The aspiration slot is implemented at its best location based on the previous experimental studies and the aspiration flow rate is fix to 1.5% of the inlet massflow. The plenum configuration follows the blade shape and remains unchanged. One-side-aspiration manner is adopted to simplify the aspiration devices. Two critical geometry parameters, slot angle and slot width, are varied to study the effects of blade aspiration slot configuration on the cascade loss, radial distribution of the aspiration flow rate and inner flow structures within the aspiration flow path. Results show that the slot configuration does affect the cascade performance. In comparison with the throughflow performance, it is especially true once the flow loss caused by the aspiration flow path is also taken into account, and higher flow loss will be generated within the aspiration flow path if an inappropriate scheme is adopted. In the present investigation, apart from the cases with larger negative slot angle, a wider slot is more preferable to a narrower one, since it could enhance the aspiration capacity near the endwall regions and lower the dissipation loss within the aspiration flow path. In terms of the slot angle, a larger negative value, i.e., the slot direction more aligned with the incoming flow, is not beneficial to improve the throughflow performance, while concerning the flow loss yield by the aspiration flow path, a proper negative slot angle is always optimal.

Atmospheric plasma torch treatment of polyethylene/boron composites: Effect on thermal stability

2014 ◽  
Vol 239 ◽  
pp. 70-77 ◽  
Author(s):  
J. Abenojar ◽  
M.A. Martínez ◽  
F. Velasco ◽  
M.A. Rodríguez-Pérez
Keyword(s):  
Thermal Stability ◽  
Plasma Torch ◽  
Atmospheric Plasma

PHOTO-CATALYTIC ACTIVITY AND PHOTO-ABSORPTION OF PLASMA-SPRAYED NANO-STRUCTURED TiO2 COATINGS

2010 ◽  
Vol 24 (31) ◽  
pp. 6115-6127 ◽  
Author(s):  
MARYAMOSSADAT BOZORGTABAR ◽  
MEHDI SALEHI ◽  
MOHAMMADREZA RAHIMIPOUR ◽  
MOHAMMADREZA JAFARPOUR
Keyword(s):  
Catalytic Activity ◽  
Flow Rate ◽  
Test Chamber ◽  
Catalytic Efficiency ◽  
Surface Characteristics ◽  
Catalytic Performance ◽  
Atmospheric Plasma ◽  
Argon Flow Rate ◽  
Photo Catalytic Activity ◽  
Argon Flow

Titanium dioxide coatings were deposited by utilizing atmospheric plasma-spraying system. The agglomerated P25/20 nano-powder and different spraying parameters (e.g., Argon flow rate and spray distance) were used to determine their influences on the microstructure, crystalline structure, photo-absorption, and photo-catalytic performance of the coatings. The microstructure and phases of as-sprayed TiO 2 coatings were characterized by scanning electron microscope SEM and X-ray diffraction, respectively. Surface characteristics were investigated by Fourier Transform Infrared. Photo-catalytic efficiency of the elaborated samples was also determined in an environmental test chamber set-up and evaluated from the conversion rate of ethanol. The photo-absorption was determined by UV–Vis spectrophotometer. The as-sprayed TiO2 coating was photo-catalytically reactive for the degradation of ethanol. The photo-catalytic activity was influenced by spray conditions. It is found that the photo-catalytic activity is significantly influenced by anatase content, surface area, and surface state. The results showed that the argon flow rate has an influence on the microstructure, anatase content, and photo-catalytic activity of the TiO 2 coatings.

Sign in / Sign up

Export Citation Format

Share Document