scholarly journals Load-Carrying Capacity of Short Concrete Columns Reinforced with Glass Fiber Reinforced Polymer Bars Under Concentric Axial Load

2019 ◽  
Vol 9 (2) ◽  
pp. 1712-1719
Keyword(s):  
Carrying Capacity ◽  
Load Capacity ◽  
Plain Concrete ◽  
Concrete Columns ◽  
Reinforcement Ratio ◽  
Load Carrying Capacity ◽  
Rc Columns ◽  
Gfrp Bars ◽  
Glass Fiber Reinforced ◽  
Load Carrying

In this paper, 1 group of plain concrete square columns 150×150×600 mm and 11 groups of concrete columns reinforced with glass fiber reinforced polymer (GFRP) were cast and tested, each group contains of 3 specimens. These experiments investigated effect of the main reinforcement ratio, stirrup spacing and contribution of longitudinal GFRP bars on the load carrying capacity of GFRP reinforced concrete (RC) columns. Based on the experiment results, the relationship between load-capacity and reinforcement ratio and the plot of contribution of longitudinal GFRP bars to load-capacity versus the reinforcement ratio were built and analyzed. By increasing the reinforcement ratio from 0.36% to 3.24%, the average ultimate strain in columns at maximum load increases from 2.64% to 75.6% and the load-carrying capacity of GFRP RC columns increases from 3.4% to 25.7% in comparison with the average values of plain concrete columns. Within the investigated range of reinforcement ratio, the longitudinal GFRP bars contributed about 0.72%-6.71% of the ultimate load-carrying capacity of the GFRP RC columns. Meanwhile, with the same configuration of reinforcement, contribution of GFRP bars to load-carrying capacity of GFRP RC columns decreases when increasing the concrete strength. The influence of tie spacing on load-carrying capacity of reinforced columns was also taken into consideration. Additionally, experimental results allow us to propose some modifications on the existing formulas to determine the bearing capacity of the GFRP RC column according to the compressive strength of concrete and GFRP bars.

scholarly journals INFLUENCE OF CONCRETE AND FIBRE CONCRETE ON THE LOAD‐CARRYING CAPACITY AND DEFORMABILITY OF COMPOSITE STEEL‐CONCRETE COLUMNS

2007 ◽  
Vol 13 (1) ◽  
pp. 55-61 ◽  
Author(s):  
Elżbieta Szmigiera
Keyword(s):  
Carrying Capacity ◽  
Load Capacity ◽  
Concrete Columns ◽  
Considerable Effect ◽  
Load Carrying Capacity ◽  
Steel Columns ◽  
Fibre Concrete ◽  
Load Carrying ◽  
Increasing Load ◽  
Composite Steel

The report presents the results of laboratories’ tests on steel columns strengthened by concrete casing. During testing of steel I‐shape column the strength of concrete casing and the way of the column loading were parameters subjected to changes. The possibility of increasing load capacity of columns by strengthening the supporting zones was checked, too. On the basis of tests performed, it has been stated that there is a considerable effect of concrete casing on the performance and capacity of steel columns. Possibility of increasing the load capacity of columns by making heads of fibre concrete has been shown.

scholarly journals The analysis of load carrying capacity and cracking of slightly reinforced concrete members in bending

2008 ◽  
Vol 2 (1) ◽  
pp. 065-078
Author(s):  
Marta Słowik
Keyword(s):  
Reinforced Concrete ◽  
Carrying Capacity ◽  
Concrete Beams ◽  
Plain Concrete ◽  
Reinforcement Ratio ◽  
Reinforced Concrete Beams ◽  
Load Carrying Capacity ◽  
Test Results ◽  
Concrete Members ◽  
Load Carrying

Slightly reinforced concrete members are the members made by concrete with reinforcement less than minimum given in codes for reinforced concrete ones. Plain concrete and slightly reinforced concrete members in bending are treated in the same way during the dimensioning and the influence of longitudinal reinforcement on the load carrying capacity is not taken into account. The mechanism of work and crack formation in slightly reinforced concrete members is not completely recognized. The author’s own research program was made. The experiment was aimed at the determination of cracking moment and load carrying capacity of slightly reinforced concrete beams with different reinforcement ratio. Also plain concrete beams and the typical reinforced concrete beam were tested. The analysis of the obtained values of maximum bending moment and crack’s widths was made according to the reinforcement ratio. The analysis of test results shows how the presence of longitudinal steel bars in concrete members, even when reinforcement ratio is low, changes cracking process and influences the value of cracking moment in flexural members. On the basis of test results, the method how to calculate the load carrying capacity of slightly reinforced concrete elements in bending has been proposed.

scholarly journals Structural Behavior of RC Columns Improved by Different Strengthening Techniques

2020 ◽  
Vol 28 (3) ◽  
pp. 20-28
Author(s):  
Shah Rukh Tariq ◽  
Liaqat Ali Qureshi ◽  
Babar Ali ◽  
Muhammad Usman Rashid
Keyword(s):  
Reinforced Concrete ◽  
Carrying Capacity ◽  
Concrete Columns ◽  
Load Carrying Capacity ◽  
Cross Sectional ◽  
Rc Columns ◽  
Reinforced Concrete Columns ◽  
Existing Structures ◽  
Axial Capacity ◽  
Load Carrying

AbstractDeficient or deteriorating reinforced-concrete columns in many existing structures have to be strengthened using economical, efficient, and fast methods. In the present study, different strengthening techniques to improve the load-carrying capacity of reinforced concrete (RC) columns have been compared. Five groups of fifteen square reinforced concrete columns (150 mm × 150 mm × 600 mm) and one group of three circular columns ( φ 170 mm) that have cross-sectional areas equivalent to those of the square columns were cast from normal-strength concrete. The test program was designed to examine the behavior of columns strengthened by carbon fiber-reinforced polymer (CFRP), steel jacketing, ferro cement, steel fibers, and silica fumes under cyclic axial compression. The efficiency of each strengthening method in increasing the column’s axial capacity, energy absorption, and ductility was studied using the experimental data. The test results showed that strengthening the columns could significantly enhance their load-carrying capacity and failure strains.

scholarly journals Circularization Technique for Strengthening of Plain Concrete Short Square Columns Subjected to a Uniaxial Compression Compressive Pressure

2019 ◽  
Vol 5 (3) ◽  
pp. 636
Author(s):  
Ahmed Waad Abdulsattar ◽  
Hayder Amer Al-Baghdadi
Keyword(s):  
Cross Section ◽  
Carrying Capacity ◽  
Plain Concrete ◽  
Concrete Columns ◽  
Load Carrying Capacity ◽  
Shape Modification ◽  
Short Columns ◽  
Load Carrying ◽  
Modification Technique ◽  
Compressive Pressure

This paper presents an experimental study for strengthening existing columns against axial compressive loads. The objective of this work is to study the behavior of concrete square columns strengthening with circulation technique. In Iraq, there are significantly more reinforced rectangular and square columns than reinforced circular columns in reinforced concrete buildings. Moreover, early research studies indicated that strengthening of rectangular or square columns using wraps of CFRP (Carbon Fiber Reinforced Polymer) provided rather little enhancement to their load-carrying capacity. In this paper, shape modification technique was performed to modify the shape (cross section) of the columns from square columns into circular columns. Shape modification technique is also called circularization technique because the cross section is modified from square into circular cross section. Then, the circularized columns were wrapped with CFRP wraps. Shape modification is the strengthening method adopted in this paper as a mean to strengthen existing square columns. Columns studied in this paper are short columns with square sections as a special case of rectangular columns. Columns in this study are plain concrete columns (having concrete strength of  = 24.41 MPa) with no internal steel reinforcement. The aim of this research is to study experimentally the behavior of circularized concrete square columns confined with CFRP wraps. Then, for better understanding, the results were compared with another, more widely used, strengthening technique which is the direct wrapping of square columns with CFRP wraps. Thus, investigating experimentally the effectiveness of the two aforementioned strengthening techniques in increasing the load-carrying capacity and ductility of the existing concrete columns. The methodology of this research is that six plain concrete short square columns were casted. These six columns were exerted to compressive pressure using concrete testing machine. These six columns were divided into three groups, each group consisted of 2 columns. The three groups were classified as follows: first group (titled L0) consisted of two square columns which were not strengthened by any method, second group (titled L1) consisted of two square columns confined by one layer of CFRP wraps, finally, the third group (titled LC1) consisted of two circularized square columns confined by one layer of CFRP wraps.Experimental results showed that load bearing capacity and ductility of square columns have been significantly enhanced. Test results showed that shape modification technique (columns LC1) produced enhancement in load carrying capacity about 167.8 % of the original non-strengthened columns (columns L0). Furthermore, square columns wrapped by one layer of CFRP wraps (columns L1) produced enhancement in load carrying capacity about 56.1% of the original non-strengthened columns (columns L0). As such, it was evident that circularization technique resulted in enhancement in load carrying capacity far more than the enhancement obtained from wrapping the square columns with CFRP wraps.

Analysis of Seismic Performance of RC Frames with Centrally Reinforced Columns

2013 ◽  
Vol 671-674 ◽  
pp. 1319-1323
Author(s):  
Zi Xue Lei ◽  
Yu Hang Han ◽  
San Sheng Dong ◽  
Jun Qing Guo
Keyword(s):  
Seismic Performance ◽  
Cross Sections ◽  
Carrying Capacity ◽  
Pushover Analysis ◽  
Seismic Load ◽  
Load Carrying Capacity ◽  
Rc Columns ◽  
Rc Column ◽  
Rc Frames ◽  
Load Carrying

A centrally reinforced column is a new type of RC columns, formed by providing a reinforcement skeleton at the central part of the cross section of an ordinary RC column. Tests have shown that as compared with an ordinary RC column, this type of columns has a higher load carrying capacity and ductility. From the pushover analysis of a frame composed of ordinary RC columns and one consisting of centrally reinforced columns, their seismic performance under seismic load of 9-degree intensity was studied according to Chinese code, including target displacements, story-level displacements, interstory drifts, appearance and development of plastic hinges. The results indicate that although the dimensions of cross sections of columns in the frame with centrally reinforced columns are smaller than those of the ordinary frame, the former still has a higher overall load carrying capacity and seismic performance than the latter.

Experimental study on the axial compression performance of GFRP-reinforced concrete square columns

2018 ◽  
Vol 22 (7) ◽  
pp. 1554-1565 ◽  
Author(s):  
Jianwei Tu ◽  
Kui Gao ◽  
Lang He ◽  
Xinping Li
Keyword(s):  
Carrying Capacity ◽  
Ultimate Load ◽  
Fiber Reinforced Polymer ◽  
Load Carrying Capacity ◽  
Longitudinal Reinforcement ◽  
Rc Columns ◽  
Compression Performance ◽  
Reinforced Polymer ◽  
Load Carrying ◽  
Ultimate Load Carrying Capacity

At present, extensive studies have been conducted relative to the topic of fiber-reinforced polymer(FRP)- reinforced concrete (RC) flexural members, and many design methods have also been introduced. There have, however, been few studies conducted on the topic of FRP-RC compression members. In light of this, eight glass-fiber-reinforced polymer (GFRP)-RC square columns (200×200×600 mm) were tested in order to investigate their axial compression performance. These columns were reinforced with GFRP longitudinal reinforcement and confined GFRP stirrup. These experiments investigated the effects of the longitudinal reinforcement ratio, stirrup configuration (spirals versus hoops) and spacing on the load-carrying capacity and failure modes of GFRP-RC rectangular columns. The test results indicate that the load-carrying capacity of longitudinal GFRP bars accounted for 3%-7% of the ultimate load-carrying capacity of the columns. The ultimate load-carrying capacity of RC columns confined with GFRP spirals increased by 0.8%-1.6% with higher ductility, compared to GFRP hoops. Reducing the stirrup spacing may prevent the buckling failure of the longitudinal bars and increase the ductility and load-carrying capacity of the GFRP-RC columns. It has been found that setting the GFRP compressive strength to 35% of the GFRP maximum tensile strength yields a reasonable estimate of ultimate load-carrying capacity of GFRP-RC columns.

scholarly journals Flexural strengthening of Reinforced Concrete (RC) Beams Retrofitted with Corrugated Glass Fiber Reinforced Polymer (GFRP) Laminates

2015 ◽  
Vol 2 (1) ◽  
Author(s):  
N. Aravind ◽  
Amiya K. Samanta ◽  
Dilip Kr. Singha Roy ◽  
Joseph V. Thanikal
Keyword(s):  
Reinforced Concrete ◽  
Carrying Capacity ◽  
Fiber Reinforced Polymer ◽  
Load Carrying Capacity ◽  
Rc Beams ◽  
Glass Fiber Reinforced Polymer ◽  
Flexural Strengthening ◽  
Reinforced Polymer ◽  
Glass Fiber Reinforced ◽  
Load Carrying

AbstractStrengthening the structural members of old buildings using advanced materials is a contemporary research in the field of repairs and rehabilitation. Many researchers used plain Glass Fiber Reinforced Polymer (GFRP) sheets for strengthening Reinforced Concrete (RC) beams. In this research work, rectangular corrugated GFRP laminates were used for strengthening RC beams to achieve higher flexural strength and load carrying capacity. Type and dimensions of corrugated profile were selected based on preliminary study using ANSYS software. A total of twenty one beams were tested to study the load carrying capacity of control specimens and beams strengthened with plain sheets and corrugated laminates using epoxy resin. This paper presents the experimental and theoretical study on flexural strengthening of Reinforced Concrete (RC) beams using corrugated GFRP laminates and the results are compared. Mathematical models were developed based on the experimental data and then the models were validated.

Experimental Study on Mechanical Properties of Axially Loaded PVC Tubed Short Concrete Columns

2011 ◽  
Vol 99-100 ◽  
pp. 715-718 ◽  
Author(s):  
Jun Dong ◽  
De Ping Chen ◽  
Ju Mei Zhao ◽  
De Shan Shan ◽  
Xin Yue Liu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Carrying Capacity ◽  
Loading Condition ◽  
Concrete Strength ◽  
Concrete Columns ◽  
Load Carrying Capacity ◽  
Composite Columns ◽  
Load Carrying ◽  
Strength And Deformation ◽  
Axially Loaded

Twelve PVC tubed short concrete columns and four columns without PVC tube confined were tested under axial load to investigate mechanical properties of axially loaded PVC tubed short concrete columns . The principal influencing factors such as concrete strength, loading condition and ratio of height to diameter were studied. Test results indicated that strength and deformation performance of core concrete increased as a result of the confinement of PVC tube. The PVC tube confinement effect on concrete will decrease with an increase in strength of concrete. Load- carrying capacity and deformation of short composite columns with different loading condition made some difference. As the ratio of height to diameter increases, load- carrying capacity and plasticity of short composite columns decreased gradually.

scholarly journals Rebars for Durable Concrete Construction: Points to Ponder

2021 ◽  
Author(s):  
Anil K. Kar
Keyword(s):  
Reinforced Concrete ◽  
Carbon Steel ◽  
Carrying Capacity ◽  
High Strength Steel ◽  
Global Climate ◽  
High Strength ◽  
Load Carrying Capacity ◽  
Glass Fiber Reinforced ◽  
Load Carrying ◽  
Total Failure

Reinforced concrete is the number one medium of construction. It is important to have good quality concrete and reinforcing bar (rebar). It is equally important to have competent bond between rebar and concrete. About six decades ago ribbed rebars of high strength steel started replacing plain round bars of mild steel, the use of which had made reinforced concrete constructions durable. It was overlooked that ribbed rebars of carbon steel would be highly susceptible to corrosion at accelerated rates. That would not only make reinforced concrete constructions reach states of distress early, that could also destroy or reduce bond between ribbed rebars and concrete. The continued use of ribbed rebars of high strength carbon steel demonstrates a widespread lack of understanding of the phenomenon of bond between rebars and concrete. This lack of understanding of bond has led to the introduction of epoxy coated ribbed rebars, ribbed stainless steel bars and glass fiber reinforced and granite reinforced polymer rebars, all of which permit reinforced concrete carry static loads because of engagement between such rebars and concrete. But the load-carrying capacity of reinforced concrete elements is impaired, and such elements become vulnerable to local or even total failure during vibratory loads. The use of PSWC-BAR, characterized by its plain surface and wave-type configuration, permits the use of medium strength and high strength steel. In the absence of ribs, the rate of corrosion is greatly reduced. The use of PSWC-BARs, at no added effort or cost, in lieu of conventional ribbed bars, leads to enhancement of effective bond or engagement between such rebars and concrete, thereby leading to increased load-carrying capacity, several-fold higher life span, ductility and energy-absorbing capacity, and great reduction in life cycle cost and adverse impact of construction on the environment and the global climate. In keeping with a lack of understanding of bond between rebars and concrete, there is arbitrariness in the selection of the required level of percent elongation and ductility of rebars.

Sign in / Sign up

Export Citation Format

Share Document