scholarly journals Strategi Smart Test Dalam Pembelajaran Latsar CPNS di Era Society 5.0

2020 ◽  
Vol 1 (1) ◽  
pp. 1-9 ◽  
Author(s):  
Agus Suharsono ◽  
Ana Uluwiyah
Keyword(s):  
Cross Sectional

Point penting dalam society 5.0 adalah terjadinya cross-sectional pada knowledge dan informasi, sehingga mendorong orang untuk dapat terus tumbuh dan berkembang menjadi pribadi masyarakat yang aktif. Konsep dalam society 5.0, telah mulai berkembang dalam budaya masyarakat Indonesia. Ada beberapa indikator penting, diantaranya adalah kesadaran masyarakat untuk menggunakan IT sebagai salah satu “enabler” dalam mendukung aktivitas pekerjaannya. Tulisan ini akan memberikan gambaran umum tentang salah satu metode pembelajaran yang mendukung terwujudnya budaya society 5.0 untuk meningkatkan kompetensi peserta diklat, melalui studi empiris dengan data hasil apada Diklat Latsar CPNS Kemenkeu. Berdasarkan hasil analisis deskriptif, diperoleh gambaran umum bahwa melalui pengembangan metode pembelajaran yang sesuai dengan budaya society 5.0, tujuan pembelajaran seperti meningkatkan kompetensi peserta lebih mudah dicapai. Alasannya karena, pengembangan metode pembelajaran, dalam paper ini menggunakan Quizziz, sesuai dengan kebutuhan dan budaya peserta yang pada dasarnya adalah 100%  generasi milineal. Hal ini dapat disimpulkan, bahwa dengan budaya masyarakat yang sudah mulai bergeser ke soceity 5.0, maka pemerintah perlu melakukan inovasi atau terobosan sesuai kebutuhan masyarakat agar lebih efektif dan efisien.

Automated Image Analysis Of Nuclear And Cytoplasmic Changes In Exfoliated Cells From Tracheas Treated With Carcinogen

1977 ◽  
Vol 35 ◽  
pp. 220-221
Author(s):  
S.F. Stinson ◽  
J.C. Lilga ◽  
M.B. Sporn
Keyword(s):  
Image Analysis ◽  
Pattern Analysis ◽  
Relative Proportion ◽  
Automated Image Analysis ◽  
Image Analyzer ◽  
Cross Sectional ◽  
Exfoliated Cells ◽  
Neoplastic Lesions ◽  
Analysis System ◽  
Morphologic Criterion

Increased nuclear size, resulting in an increase in the relative proportion of nuclear to cytoplasmic sizes, is an important morphologic criterion for the evaluation of neoplastic and pre-neoplastic cells. This paper describes investigations into the suitability of automated image analysis for quantitating changes in nuclear and cytoplasmic cross-sectional areas in exfoliated cells from tracheas treated with carcinogen.Neoplastic and pre-neoplastic lesions were induced in the tracheas of Syrian hamsters with the carcinogen N-methyl-N-nitrosourea. Cytology samples were collected intra-tracheally with a specially designed catheter (1) and stained by a modified Papanicolaou technique. Three cytology specimens were selected from animals with normal tracheas, 3 from animals with dysplastic changes, and 3 from animals with epidermoid carcinoma. One hundred randomly selected cells on each slide were analyzed with a Bausch and Lomb Pattern Analysis System automated image analyzer.

X-Ray Replication of Submicrometer Linewidth Patterns

1977 ◽  
Vol 35 ◽  
pp. 136-137
Author(s):  
Henry I. Smith ◽  
D.C. Flanders
Keyword(s):  
Electron Beam Lithography ◽  
Cross Sectional ◽  
X Ray ◽  
Electron Backscattering ◽  
Spatial Frequencies ◽  
Cross Sectional Profile ◽  
Carbon Foils ◽  
Sectional Profile ◽  
And Control ◽  
Soft Radiation

Scanning electron beam lithography has been used for a number of years to write submicrometer linewidth patterns in radiation sensitive films (resist films) on substrates. On semi-infinite substrates, electron backscattering severely limits the exposure latitude and control of cross-sectional profile for patterns having fundamental spatial frequencies below about 4000 Å(l),Recently, STEM'S have been used to write patterns with linewidths below 100 Å. To avoid the detrimental effects of electron backscattering however, the substrates had to be carbon foils about 100 Å thick (2,3). X-ray lithography using the very soft radiation in the range 10 - 50 Å avoids the problem of backscattering and thus permits one to replicate on semi-infinite substrates patterns with linewidths of the order of 1000 Å and less, and in addition provides means for controlling cross-sectional profiles. X-radiation in the range 4-10 Å on the other hand is appropriate for replicating patterns in the linewidth range above about 3000 Å, and thus is most appropriate for microelectronic applications (4 - 6).

A Field Emission System For Transmission Electron Microscopy

1973 ◽  
Vol 31 ◽  
pp. 298-299
Author(s):  
Michel Troyonal ◽  
Huei Pei Kuoal ◽  
Benjamin M. Siegelal
Keyword(s):  
Electron Microscope ◽  
Field Emission ◽  
Optical System ◽  
High Vacuum ◽  
Ultra High Vacuum ◽  
Objective Lens ◽  
Electron Optical System ◽  
Cross Sectional ◽  
Transmission Electron ◽  
Emission System

A field emission system for our experimental ultra high vacuum electron microscope has been designed, constructed and tested. The electron optical system is based on the prototype whose performance has already been reported. A cross-sectional schematic illustrating the field emission source, preaccelerator lens and accelerator is given in Fig. 1. This field emission system is designed to be used with an electron microscope operated at 100-150kV in the conventional transmission mode. The electron optical system used to control the imaging of the field emission beam on the specimen consists of a weak condenser lens and the pre-field of a strong objective lens. The pre-accelerator lens is an einzel lens and is operated together with the accelerator in the constant angular magnification mode (CAM).

Microstructural characterization of CoPtCr/Cr thin film disks by cross-section TEM and elongated probe micro-diffraction

1991 ◽  
Vol 49 ◽  
pp. 762-763
Author(s):  
M.A. Parker ◽  
K.E. Johnson ◽  
C. Hwang ◽  
A. Bermea
Keyword(s):  
Magnetic Recording ◽  
Electron Probe ◽  
Microstructural Characterization ◽  
Crystallographic Structure ◽  
Recording Media ◽  
Layer By Layer ◽  
Cross Sectional ◽  
New Techniques ◽  
Polished Side

We have reported the dependence of the magnetic and recording properties of CoPtCr recording media on the thickness of the Cr underlayer. It was inferred from XRD data that grain-to-grain epitaxy of the Cr with the CoPtCr was responsible for the interaction observed between these layers. However, no cross-sectional TEM (XTEM) work was performed to confirm this inference. In this paper, we report the application of new techniques for preparing XTEM specimens from actual magnetic recording disks, and for layer-by-layer micro-diffraction with an electron probe elongated parallel to the surface of the deposited structure which elucidate the effect of the crystallographic structure of the Cr on that of the CoPtCr.XTEM specimens were prepared from magnetic recording disks by modifying a technique used to prepare semiconductor specimens. After 3mm disks were prepared per the standard XTEM procedure, these disks were then lapped using a tripod polishing device. A grid with a single 1mmx2mm hole was then glued with M-bond 610 to the polished side of the disk.

Computer Reconstruction of the Cellular Architecture of the Daphnia Magna Optic Ganglion

1975 ◽  
Vol 33 ◽  
pp. 284-285
Author(s):  
E. R. Macagno ◽  
C. Levinthal
Keyword(s):  
Daphnia Magna ◽  
Genetic Background ◽  
Compound Eye ◽  
Synaptic Connectivity ◽  
Serial Sections ◽  
Cross Sectional ◽  
Small Crustacean ◽  
Optic Ganglion ◽  
Structural Invariance ◽  
High Degree

The optic ganglion of Daphnia Magna, a small crustacean that reproduces parthenogenetically contains about three hundred neurons: 110 neurons in the Lamina or anterior region and about 190 neurons in the Medulla or posterior region. The ganglion lies in the midplane of the organism and shows a high degree of left-right symmetry in its structures. The Lamina neurons form the first projection of the visual output from 176 retinula cells in the compound eye. In order to answer questions about structural invariance under constant genetic background, we have begun to reconstruct in detail the morphology and synaptic connectivity of various neurons in this ganglion from electron micrographs of serial sections (1). The ganglion is sectioned in a dorso-ventra1 direction so as to minimize the cross-sectional area photographed in each section. This area is about 60 μm x 120 μm, and hence most of the ganglion fit in a single 70 mm micrograph at the lowest magnification (685x) available on our Zeiss EM9-S.

Mass Determination by Direct Measurement of Electron Scattering

1975 ◽  
Vol 33 ◽  
pp. 240-241
Author(s):  
M. K. Lamvik ◽  
A. V. Crewe
Keyword(s):  
Cross Section ◽  
Electron Scattering ◽  
Mass Density ◽  
Variable Mass ◽  
Scattering Cross Section ◽  
Mass Determination ◽  
Number Density ◽  
Cross Sectional ◽  
Thin Slice ◽  
Scattering Cross

If a molecule or atom of material has molecular weight A, the number density of such units is given by n=Nρ/A, where N is Avogadro's number and ρ is the mass density of the material. The amount of scattering from each unit can be written by assigning an imaginary cross-sectional area σ to each unit. If the current I0 is incident on a thin slice of material of thickness z and the current I remains unscattered, then the scattering cross-section σ is defined by I=IOnσz. For a specimen that is not thin, the definition must be applied to each imaginary thin slice and the result I/I0 =exp(-nσz) is obtained by integrating over the whole thickness. It is useful to separate the variable mass-thickness w=ρz from the other factors to yield I/I0 =exp(-sw), where s=Nσ/A is the scattering cross-section per unit mass.

X-ray micro tomography in the scanning electron microscope

1978 ◽  
Vol 36 (1) ◽  
pp. 106-107 ◽  
Author(s):  
W. Brünger
Keyword(s):  
Electron Beam ◽  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
Target Surface ◽  
The Body ◽  
X Rays ◽  
Cross Sectional ◽  
X Ray ◽  
Micro Tomography ◽  
Scanning Electron

Reconstructive tomography is a new technique in diagnostic radiology for imaging cross-sectional planes of the human body /1/. A collimated beam of X-rays is scanned through a thin slice of the body and the transmitted intensity is recorded by a detector giving a linear shadow graph or projection (see fig. 1). Many of these projections at different angles are used to reconstruct the body-layer, usually with the aid of a computer. The picture element size of present tomographic scanners is approximately 1.1 mm2.Micro tomography can be realized using the very fine X-ray source generated by the focused electron beam of a scanning electron microscope (see fig. 2). The translation of the X-ray source is done by a line scan of the electron beam on a polished target surface /2/. Projections at different angles are produced by rotating the object.During the registration of a single scan the electron beam is deflected in one direction only, while both deflections are operating in the display tube.

A tilting high temperature gas reaction chamber for the JEM 7A T.E.M.

1978 ◽  
Vol 36 (1) ◽  
pp. 70-71
Author(s):  
Brian L. Rhoades
Keyword(s):  
Cross Section ◽  
Reaction Chamber ◽  
Objective Lens ◽  
Reduced Cross Section ◽  
Cross Sectional ◽  
Structural Investigations ◽  
Transmission Electron ◽  
Dynamic Experiments ◽  
Successful Design ◽  
Thermocouple Junction

A gas reaction chamber has been designed and constructed for the JEM 7A transmission electron microscope which is based on a notably successful design by Hashimoto et. al. but which provides specimen tilting facilities of ± 15° aboutany axis in the plane of the specimen.It has been difficult to provide tilting facilities on environmental chambers for 100 kV microscopes owing to the fundamental lack of available space within the objective lens and the scope of structural investigations possible during dynamic experiments has been limited with previous specimen chambers not possessing this facility.A cross sectional diagram of the specimen chamber is shown in figure 1. The specimen is placed on a platinum ribbon which is mounted on a mica ring of the type shown in figure 2. The ribbon is heated by direct current, and a thermocouple junction spot welded to the section of the ribbon of reduced cross section enables temperature measurement at the point where localised heating occurs.

TEM characterization of silicon epitaxial layer grown on Si-TaS2, eutectic composites

1991 ◽  
Vol 49 ◽  
pp. 802-803
Author(s):  
C.M. Sung ◽  
M. Levinson ◽  
M. Tabasky ◽  
K. Ostreicher ◽  
B.M. Ditchek
Keyword(s):  
Substrate Surface ◽  
Bulk Sample ◽  
Surface Cleaning ◽  
Native Oxide ◽  
Czochralski Growth ◽  
Ion Milling ◽  
Cross Sectional ◽  
Cleaning Methods ◽  
Field Emission Cathodes

Directionally solidified Si/TaSi2 eutectic composites for the development of electronic devices (e.g. photodiodes and field-emission cathodes) were made using a Czochralski growth technique. High quality epitaxial growth of silicon on the eutectic composite substrates requires a clean silicon substrate surface prior to the growth process. Hence a preepitaxial surface cleaning step is highly desirable. The purpose of this paper is to investigate the effect of surface cleaning methods on the epilayer/substrate interface and the characterization of silicon epilayers grown on Si/TaSi2 substrates by TEM.Wafers were cut normal to the <111> growth axis of the silicon matrix from an approximately 1 cm diameter Si/TaSi2 composite boule. Four pre-treatments were employed to remove native oxide and other contaminants: 1) No treatment, 2) HF only; 3) HC1 only; and 4) both HF and HCl. The cross-sectional specimens for TEM study were prepared by cutting the bulk sample into sheets perpendicular to the TaSi2 fiber axes. The material was then prepared in the usual manner to produce samples having a thickness of 10μm. The final step was ion milling in Ar+ until breakthrough occurred. The TEM samples were then analyzed at 120 keV using the Philips EM400T.

Sign in / Sign up

Export Citation Format

Share Document