scholarly journals Robust Digital Control for Interleaved PFC Boost Converter Using Approximate 2DOF

1970 ◽  
Vol 8 (2) ◽  
pp. 187-194
Author(s):  
Yuki Satake ◽  
Hiroyuki Furuya ◽  
Yohei Mochizuki ◽  
Yuji Fukaishi ◽  
Kohji Higuchi ◽  
...  
Keyword(s):  
Power Factor ◽  
Output Voltage ◽  
Sudden Change ◽  
Experimental Studies ◽  
Input Voltage ◽  
Boost Converter ◽  
Buck Converter ◽  
Digital Controller ◽  
Step Response ◽  
Duty Ratio

In recent years, improving of power factor and reducing harmonic distortion in electrical instruments are needed. In general, a current conduction mode boost converter is used for active PFC (Power Factor Correction). In a PFC boost converter, if a duty ratio, a load resistance and an input voltage are changed, the dynamic characteristics are varied greatly. This is the prime reason of difficulty of controlling the interleaved PFC boost converter. In this paper, a robust digital controller for suppressing the change of step response characteristics and variation of output voltage at a DC-DC buck converter load sudden change with high power factor and low harmonic is proposed. Experimental studies using a micro-processor for controller demonstrate that the proposed digital controller is effective to improve power factor and to suppress output voltage variation.

scholarly journals SINGLE STAGE LOW FREQUENCY ELECTRONIC BALLAST FOR HID LAMPS

2014 ◽  
pp. 251-255
Author(s):  
SUMAN TOLANUR ◽  
S.N KESHAVA MURTHY
Keyword(s):  
Power Factor ◽  
Low Frequency ◽  
Acoustic Resonance ◽  
Input Voltage ◽  
Boost Converter ◽  
Buck Converter ◽  
Metal Halide ◽  
Single Stage ◽  
Duty Ratio ◽  
Electronic Ballast

The paper presents a single-stage high-power-factor electronic ballast for metal halide lamps. The proposed ballast integrates a buck-boost converter, a buck converter and a full-bridge inverter into a single power conversion circuit. The buck-boost converter served as a power factor corrector (PFC) is designed to operate at discontinuous conduction mode (DCM) to achieve nearly a unity power factor at the input line. By adjusting the duty-ratio of the active switches of the PFC, the lamp power is remained at rated value for universal input voltage ranged from 90 Vrms to 264 Vrms. The four active switches of the full-bridge inverter, an inductor and a capacitor form a bidirectional buck converter which supplies a low frequency square-wave currentfor the lamp at to avoid the lamp from happing acoustic resonance. The circuit operation is analyzed in detail to derive the design equations. A prototype electronic ballast for a 70 W metal halide lamp is built and tested.

scholarly journals Voltage Tracking Control of DC- DC Boost Converter Using Fuzzy Neural Network

2018 ◽  
Vol 9 (4) ◽  
pp. 1657 ◽  
Author(s):  
Waleed Ishaq Hameed ◽  
Baha Aldeen Sawadi ◽  
Ali Muayed
Keyword(s):  
Neural Network ◽  
Tracking Control ◽  
Output Voltage ◽  
Fuzzy Neural Network ◽  
Sudden Change ◽  
Input Voltage ◽  
Boost Converter ◽  
Data Sets ◽  
Fuzzy Neural ◽  
Output Load

<span lang="EN-US">This paper deals with voltage tracking control of DC- DC boost converter based on Fuzzy neural network. Maintaining the output voltage of the boost converter in some applications are very important, especially for sudden change in the load or disturbance in the input voltage. Traditional control methods usually have some disadvantages in eliminating these disturbances, as the speed of response to these changes is slow and thus affect the regularity of the output voltage of the converter. The strategy is to sense the output voltage across the load and compare it with the reference voltage to ensure that it follows the required reference voltages. In this research, fuzzy neural was introduced to achieve the purpose of voltage tracking by training the parameter of controller based on previous data. These data sets are the sensing input voltage of the converter and the value of the output load changes. To establish the performance of proposed method, MATLAB/SIMULINK environments are presented, simulation results shows that proposed method works more precisely, faster in response and elimination the disturbances</span>

scholarly journals Robust Digital Control for an LLC Current-Resonant DC-DC Converter

1970 ◽  
Vol 7 (1) ◽  
pp. 71-78
Author(s):  
Tomoya Nishimura ◽  
Yuto Adachi ◽  
Yoshihiro Ohta ◽  
Kohji Higuchi ◽  
Eiji Takegami ◽  
...  
Keyword(s):  
Output Voltage ◽  
Sudden Change ◽  
Experimental Studies ◽  
Load Resistance ◽  
Pulse Frequency ◽  
Step Response ◽  
Response Characteristics ◽  
Change Dynamics ◽  
Voltage Variation ◽  
Single Controller

If a pulse frequency and a load resistance of an LLC current-resonant DC-DC converter are changed, the dynamic characteristics are varied greatly, that is, the LLC current-resonant DC-DC converter has non-linear characteristics. In many applications of DC-DC converters, loads cannot be specified in advance, and they will be changed suddenly from no loads to full loads. A DC-DC converter system used a conventional single controller cannot be adapted to change dynamics and it occurs large output voltage variation. In this paper, a robust digital controllerfor suppress the change of step response characteristics and variation of output voltage in the load sudden change is proposed. Experimental studies using a micro-processor for the controller demonstrate that this type of digital controller is effective to suppress the variation.

Design and Control for the Buck-Boost Converter Combining 1-Plus-D Converter and Synchronous Rectified Buck Converters

2015 ◽  
Vol 6 (2) ◽  
pp. 305
Author(s):  
Jeevan Naik
Keyword(s):  
Output Voltage ◽  
Input Voltage ◽  
Boost Converter ◽  
Buck Converter ◽  
Voltage Source ◽  
Buck Converters ◽  
Power Switches ◽  
Output Capacitor ◽  
And Control ◽  
Conduction Mode

<span>In this paper, a design and control for the buck-boost converter, i.e., 1-plus-D converter with a positive output voltage, is presented, which combines the 1-plus-D converter and the synchronous rectified (SR) buck converter. By doing so, the problem in voltage bucking of the 1-plus-D converter can be solved, thereby increasing the application capability of the 1-plus-D converter. Since such a converter operates in continuous conduction mode inherently, it possesses the nonpulsating output current, thereby not only decreasing the current stress on the output capacitor but also reducing the output voltage ripple. Above all, both the 1-plus-D converter and the SR buck converter, combined into a buck–boost converter with no right-half plane zero, use the same power switches, thereby causing the required circuit to be compact and the corresponding cost to be down. Furthermore, during the magnetization period, the input voltage of the 1-plus-D converter comes from the input voltage source, whereas during the demagnetization period, the input voltage of the 1-plus-D converter comes from the output voltage of the SR buck converter.</span>

scholarly journals Quadratic Boost Converter

2021 ◽  
Vol 9 (VII) ◽  
pp. 2010-2014
Author(s):  
Mamidala Hemanth Reddy
Keyword(s):  
Output Voltage ◽  
Semiconductor Device ◽  
Low Voltage ◽  
Input Voltage ◽  
Boost Converter ◽  
Voltage Gain ◽  
Practical Utilization ◽  
Analysis And Design ◽  
Simulink Model ◽  
Grid Connection

The output voltage from the sustainable energy like photovoltaic (PV) arrays and fuel cells will be at less amount of level. This must be boost considerably for practical utilization or grid connection. A conventional boost converter will provides low voltage gain while Quadratic boost converter (QBC) provides high voltage gain. QBC is able to regulate the output voltage and the choice of second inductor can give its current as positive and whereas for boost increases in the voltage will not able to regulate the output voltage. It has low semiconductor device voltage stress and switch usage factor is high. Analysis and design modeling of Quadratic boost converter is proposed in this paper. A power with 50 W is developed with 18 V input voltage and yield 70 V output voltage and the outcomes are approved through recreation utilizing MATLAB/SIMULINK MODEL.

scholarly journals Implementation of Buck-Boost Converter as Low Voltage Stabilizer at 15 V

2019 ◽  
Vol 9 (4) ◽  
pp. 2230
Author(s):  
Suwarno Suwarno ◽  
Tole Sutikno
Keyword(s):  
Power Electronics ◽  
Wind Power ◽  
Output Voltage ◽  
Low Voltage ◽  
Input Voltage ◽  
Boost Converter ◽  
Voltage Stabilizer ◽  
Voltage Regulator ◽  
Output Current ◽  
Converter Design

<p>This paper presents the implementation of the buck-boost converter design which is a power electronics applications that can stabilize voltage, even though the input voltage changes. Regulator to stabilize the voltage using PWM pulse that triger pin 2 on XL6009. In this design of buck-boost converter is implemented using the XL6009, LM7815 and TIP2955. LM7815 as output voltage regulator at 15V with 1A output current, while TIP2955 is able to overcome output current up to 5A. When the LM7815 and TIP2955 are connected in parallel, the converter can increase the output current to 6A.. Testing is done using varied voltage sources that can be set. The results obtained from this design can be applied to PV (Photovoltaic) and WP (Wind Power), with changes in input voltage between 3-21V dc can produce output voltage 15V.</p>

scholarly journals Modified Multi Input Multilevel DC-DC Boost Converter for Hybrid Energy Systems

2020 ◽  
Vol 9 (4) ◽  
pp. 1067-1072
Keyword(s):  
Output Voltage ◽  
Low Voltage ◽  
Complex Structure ◽  
Energy Systems ◽  
Input Voltage ◽  
Boost Converter ◽  
Design Parameters ◽  
Hybrid Energy ◽  
Hybrid Energy Systems ◽  
Constant Output

DC-DC converters are playing an important role in designing of Electric Vehicles, integration of solar cells and other DC applications. Contemporary high power applications use multilevel converters that have multi stage outputs for integrating low voltage sources. Conventional DC-DC converters use single source and have complex structure while using for Hybrid Energy Systems. This paper proposes a multi-input, multi-output DC-DC converter to produce constant output voltage at different input voltage conditions. This topology is best suitable for hybrid power systems where the output voltage is variable due to environmental conditions. It reduces the requirement of magnetic components in the circuit and also reduces the switching losses. The proposed topology has two parts namely multi-input boost converter and level-balancing circuit. Boost converter increases the input voltage and Level Balancing Circuit produce Multi output. Equal values of capacitors are used in Level Balancing Circuit to ensure the constant output voltage at all output stages. The operating modes of each part are given and the design parameters of each part are calculated. Performance of the proposed topology is verified using MATLAB/Simulink simulation which shows the correctness of the analytical approach. Hardware is also presented to evaluate the simulation results.

scholarly journals Mathematical modeling and control of wind energy electric conversion system feeding standalone load

2017 ◽  
Vol 7 (1.2) ◽  
pp. 47
Author(s):  
N K Rayaguru ◽  
N. Poornachandra Rao ◽  
K. Navin Sam ◽  
Sunil Kumar Thakur
Keyword(s):  
Wind Energy ◽  
State Space ◽  
Output Voltage ◽  
State Space Model ◽  
Synchronous Generator ◽  
Boost Converter ◽  
Duty Ratio ◽  
Space Model ◽  
Conversion System ◽  
Constant Output

In this paper, state space model of the complete Wind Energy Electric Conversion System (WEECS) comprising of wind turbine, Permanent Magnet Synchronous Generator (PMSG), uncontrolled rectifier, DC-DC boost converter, and SPWM inverter feeding a standalone load has been formulated. The derived state space model is then simulated using Matlab/Simulink to test the model. As the standalone three phase load connected to the inverter demands constant output voltage irrespective of intermittent wind pattern, a PI controller is used to control the duty ratio of DC-DC boost converter to maintain constant output voltage at the inverter end.

scholarly journals Vertical Axis Wind Turbine Improvement using DC-DC Boost Converter

2020 ◽  
Vol 188 ◽  
pp. 00017
Author(s):  
Khairunnisa Khairunnisa ◽  
Syaiful Rachman ◽  
Edi Yohanes ◽  
Awan Uji Krismanto ◽  
Jazuli Fadil ◽  
...  
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Output Voltage ◽  
Vertical Axis ◽  
Input Voltage ◽  
Pi Controller ◽  
Boost Converter ◽  
Oxide Semiconductor ◽  
Vertical Axis Wind Turbine ◽  
Constant Output

Vertical axis wind turbine (VAWT) can be operated in any direction of wind speed, but it has low rotation. To improve the performance of VAWT in which low rotation, this paper presents a simple control strategy of VAWT using a DC-DC boost converter to tap constant voltage in a standalone application. The main objective of this research is to maintain a constant output voltage of converter despite variation input voltage affected by variable wind speed. A simple proportional-integral (PI) controller has been used for a DC-DC boost converter and tested in MATLAB-Simulink environment, with the closed-loop system of the converter maintain constant output voltage although the wind speed is kept changing. The PI controller obtains the feedback from the output voltage of the boost converter to produce the correct pulse width modulation (PWM) duty cycle and trigger the metal oxide semiconductor field effect transistor (MOSFET) following the reference voltage of the turbine. This system has suppressed the value of overshoot and increased the efficiency of wind turbines as 34 %.

scholarly journals PENGISIAN AKI DENGAN BUCK CONVERTER

2013 ◽  
Vol 5 (1) ◽  
pp. 29-34
Author(s):  
Yul Antonisfia ◽  
Era Madona
Keyword(s):  
High Voltage ◽  
Output Voltage ◽  
Input Voltage ◽  
Buck Converter ◽  
Flow Sensor ◽  
Voltage Output ◽  
Charging Current ◽  
Lower Voltage

Buck converter is one of DC chopper which has the function of stabilizing the voltage to lower voltage where the output voltage is lower than the input voltage without having to remove power is relatively large. By using a buck converter is a high voltage can be reduced to lower as you wish without losing power is relatively large. The voltage output of the buck converter is able to charge the battery. The magnitude of the output voltage depends dutycyle switching generated by the microcontroller. This tool is also equipped with a flow sensor is used to detect the charging current into the battery. If the charging current is reduced, the buzzer will sound. The tool is based microcontrollers using BASCOM ATMEGA8535, which can generate a PWM with dutycyle specified. Dutycyle determined the size of the input voltage and the desired output.

Sign in / Sign up

Export Citation Format

Share Document