Properties of Bamboo Fiber Reinforced Cornstarch-Based Composites

2012 ◽  
Vol 200 ◽  
pp. 237-242
Author(s):  
Guang Sheng Zeng ◽  
Rui Zhen Lin ◽  
Cong Meng ◽  
Lei Chen
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
High Temperature ◽  
Extrusion Process ◽  
Elongation Rate ◽  
Bamboo Fiber ◽  
Physical Methods ◽  
Plasticizer Content ◽  
Different Content ◽  
Properties Of Composites

In this paper the composites made of cornstarch and PVA as matrix, bamboo fiber as reinforcement, glycerol and urea as mixed plasticizer were prepared through the extrusion molding. By physical methods, the effects of cornstarch, bamboo fiber, PVA and mixed plasticizer on the mechanical properties of composites were investigated. SEM was used to observe the influence of different content of mixed plasticizer in cornstarch. The results showed that an increase in mixed plasticizer content from 10% to 40% in cornstarch did improve the mechanical properties of the composites compared without mixed plasticizer, and when the mixed plasticizer (wt-glycerol: wt-urea=2:1) content was 30% to cornstarch, the composite showed the highest tensile strength and elongation rate. Composites made from 20% of bamboo fiber, 30% of cornstarch, 50% of PVA and 30% of mixed plasticizer to cornstarch gave the best tensile strength (15.8N). Glycerol and urea could permeate the cornstarch molecules and plasticize it under high temperature and shearing in the extrusion process.

Effects of Si, Cu and Mg on the High-Temperature Mechanical Properties of Al-Si-Cu-Mg Alloy

2013 ◽  
Vol 652-654 ◽  
pp. 1030-1034 ◽  
Author(s):  
Wen Da Zhang ◽  
Jing Yang ◽  
Jing Zhi Dang ◽  
Yun Liu ◽  
Hong Xu
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
High Temperature ◽  
Initial Crack ◽  
Elongation Rate ◽  
Mg Alloy ◽  
High Temperature Mechanical Properties ◽  
High Temperature Tensile ◽  
The Relationship ◽  
Scanning Electron

The regression equation of the relationship between Si, Cu and Mg and the mechanical properties of Al-Si-Cu-Mg alloy was established according to the orthogonal experimental results. The microstructure of the Al-Si-Cu-Mg alloy was analyzed with scanning electron microscopy and energy dispersive spectroscopy. The results show that Si, Cu and Mg affected the mechanical properties (tensile strength and elongation rate) at 250 °C most significantly, minimally and negatively, respectively. The interactions between Cu, Mg and Si greatly reduced the high-temperature tensile strength owing to the formation of brittle and hard intermetallic Al5Mg8Cu2Si6 that behaved as the initial crack during stretching.

scholarly journals The Influence of La and Ce on Microstructure and Mechanical Properties of an Al-Si-Cu-Mg-Fe Alloy at High Temperature

Metals ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 384
Author(s):  
Andong Du ◽  
Anders E. W. Jarfors ◽  
Jinchuan Zheng ◽  
Kaikun Wang ◽  
Gegang Yu
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
High Temperature ◽  
Intermetallic Phases ◽  
High Temperature Strength ◽  
Thermal Expansion Mismatch ◽  
Strengthening Mechanisms ◽  
High Temperature Mechanical Properties ◽  
Minor Contribution ◽  
A Minor

The effect of lanthanum (La)+cerium (Ce) addition on the high-temperature strength of an aluminum (Al)–silicon (Si)–copper (Cu)–magnesium (Mg)–iron (Fe)–manganese (Mn) alloy was investigated. A great number of plate-like intermetallics, Al11(Ce, La)3- and blocky α-Al15(Fe, Mn)3Si2-precipitates, were observed. The results showed that the high-temperature mechanical properties depended strongly on the amount and morphology of the intermetallic phases formed. The precipitated tiny Al11(Ce, La)3 and α-Al15(Fe, Mn)3Si2 both contributed to the high-temperature mechanical properties, especially at 300 °C and 400 °C. The formation of coarse plate-like Al11(Ce, La)3, at the highest (Ce-La) additions, reduced the mechanical properties at (≤300) ℃ and improved the properties at 400 ℃. Analysis of the strengthening mechanisms revealed that the load-bearing mechanism was the main contributing mechanism with no contribution from thermal-expansion mismatch effects. Strain hardening had a minor contribution to the tensile strength at high-temperature.

Performance of Bamboo Fiber Reinforced Composites: Mechanical Properties

2021 ◽  
Vol 879 ◽  
pp. 284-293
Author(s):  
Norliana Bakar ◽  
Siew Choo Chin
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Vinyl Ester ◽  
Fiber Volume Fraction ◽  
Volume Fraction ◽  
Bamboo Fiber ◽  
Synthetic Fiber ◽  
Fiber Reinforced ◽  
Fiber Volume ◽  
Volume Fractions

Fiber Reinforced Polymer (FRP) made from synthetic fiber had been widely used for strengthening of reinforced concrete (RC) structures in the past decades. Due to its high cost, detrimental to the environment and human health, natural fiber composites becoming the current alternatives towards a green and environmental friendly material. This paper presents an investigation on the mechanical properties of bamboo fiber reinforced composite (BFRC) with different types of resins. The BFRC specimens were prepared by hand lay-up method using epoxy and vinyl-ester resins. Bamboo fiber volume fractions, 30%, 35%, 40%, 45% and 50% was experimentally investigated by conducting tensile and flexural test, respectively. Results showed that the tensile and flexural strength of bamboo fiber reinforced epoxy composite (BFREC) was 63.2% greater than the bamboo fiber reinforced vinyl-ester composite (BFRVC). It was found that 45% of bamboo fiber volume fraction on BFREC exhibited the highest tensile strength compared to other BFRECs. Meanwhile, 40% bamboo fiber volume fraction of BFRVC showed the highest tensile strength between bamboo fiber volume fractions for BFRC using vinyl-ester resin. Studies showed that epoxy-based BFRC exhibited excellent results compared to the vinyl-ester-based composite. Further studies are required on using BFRC epoxy-based composite in various structural applications and strengthening purposes.

Influence of Processing Parameters and Different Content of Tib2 Ceramics on the Properties of Composites Sintered by High Pressure -High Temperature (HP-HT) Method

2014 ◽  
Vol 59 (1) ◽  
pp. 205-209 ◽  
Author(s):  
I. Sulima ◽  
L. Jaworska ◽  
P. Figiel
Keyword(s):  
High Pressure ◽  
High Temperature ◽  
Processing Parameters ◽  
Structure Changes ◽  
High Pressure High Temperature ◽  
Mechanical And Physical Properties ◽  
Temperature And Pressure ◽  
Different Content ◽  
Scanning Electron ◽  
Properties Of Composites

Abstract In this paper the properties of the austenitic stainless steel reinforced with various volume fractions of TiB2 ceramics have been studied. The high pressure- high temperature (HP-HT) method of sintering was applied to the formation of composites. Samples were sintered at pressure of 5 and 7 ±0.2 GPa and temperatures of 1273 K and 1573 K. For the tested materials, the relative density, Young’s modulus and hardness were measured. In order to investigate the structure changes, the scanning electron microscope was used. The obtained results show that the temperature and pressure influence on the mechanical and physical properties of the investigated composites.

Effect of Al2O3 nanofibers on compaction, phase composition, and mechanical properties of ZrO2-based composites obtained by vacuum pressureless sintering

2021 ◽  
pp. 132-143
Author(s):  
A. A. Leonov ◽  
E. V. Abdulmenova ◽  
M. P. Kalashnikov ◽  
Jing Li
Keyword(s):  
Mechanical Properties ◽  
Phase Composition ◽  
Crack Resistance ◽  
Physicomechanical Properties ◽  
Relative Content ◽  
Pressureless Sintering ◽  
Vacuum Sintering ◽  
Tetragonal Modification ◽  
Different Content ◽  
Properties Of Composites

This work studies the effect of the relative content of Al2O3 nanofibers on the compaction, phase composition, and physicomechanical properties of composites based on ZrO2 obtained by free vacuum sintering. It was found that in the process of manufacturing composites, nanofibers are sintered into Al2O3 grains of complex, elongated shape, which form a solid, frame-reinforcing structure. The relative density of composites with 5 wt. % and 10 wt. % of nanofibers, decreases up to 95%. It is shown that in all sintered samples the tetragonal modification of ZrO2 acts as the main phase, and the different content of nanofibers affects the amount of cubic and monoclinic modifications of ZrO2. It was found that addition of 5 wt. % and 10 wt. % of Al2O3 nanofibers increases the microhardness of the composite by 11% and crack resistance by 46%.

scholarly journals Effects of Zr, Y on the Microstructure and Properties of As-Cast Cu-0.5Y-xZr (wt.%) Alloys

Metals ◽  
2019 ◽  
Vol 9 (10) ◽  
pp. 1084
Author(s):  
Dong Liang ◽  
Ning Wang ◽  
Yuxiang Wang ◽  
Zhenjie Liu ◽  
Ying Fu
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Tensile Strength ◽  
Copper Alloys ◽  
Testing Machine ◽  
Elongation Rate ◽  
Nominal Composition ◽  
Microstructure And Properties ◽  
Universal Material Testing Machine ◽  
Material Testing Machine

In this paper, the microstructure and properties of as-cast Cu-Y-Zr alloys with different Zr content were studied in order to investigate whether the precipitates in copper alloys would interact with each other by adding Y and Zr simultaneously. As-cast Cu-0.5Y-xZr (wt.%, x = 0.05 and 0.1, nominal composition) alloys were prepared by vacuum melting in this study. Scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), X-ray diffraction (XRD), and transmission electron microscopy (TEM) were used to observe the microstructure of the alloys. The mechanical properties of the alloys were tested by universal material testing machine at room temperature. The effects of Zr content on the microstructure and mechanical properties of the alloys were explored. As shown by the research results, in the as-cast Cu-0.5Y-xZr (wt.%) alloys, the precipitated phase was the Cu5Y/Cu5Zr phase and ranged from 10 nm to 70 nm in size; when the Zr content increased from 0.05 wt.% to 0.1 wt.%, both the tensile strength and elongation rate of the alloys increased; when the Zr content was 0.1 wt.%, the tensile strength was 225 MPa and the elongation rate was 22.5%.

Influence of Al-10RE Modification on Microstructure and Mechanical Properties of ZL203 Aluminum Alloy

2011 ◽  
Vol 365 ◽  
pp. 98-103
Author(s):  
De Quan Shi ◽  
Gui Li Gao ◽  
Zhi Wei Gao ◽  
Yan Liu Wang ◽  
Xu Dong Wang
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Aluminum Alloy ◽  
Mechanical Testing ◽  
Testing Machine ◽  
Optical Microscope ◽  
Elongation Rate ◽  
Holding Time ◽  
Holding Temperature ◽  
Universal Mechanical Testing Machine

The influence of Al-10RE addition, holding time and holding temperature on the microstructures and mechanical properties of ZL203 aluminum alloy has been studied respectively through using the optical microscope and the universal mechanical testing machine. The experimental results lead to the following conclusions. When Al-10RE addition is 1.0%-1.5%, the holding time is 15 minutes and the holding temperature is 730°C-750°C, the microstructure of Zl203 is perfect. With the increase of Al-10RE addition, the mechanical properties including tensile strength, elongation rate and hardness gradually increase. When the Al-10RE addition is 1.0%-1.5%, the mechanical properties reaches maximum. When the Al-10RE addition is above 1.5%, the mechanical properties decrease with the increase of Al-10RE addition.

Microstructure and Mechanical Properties of Mg-Based Composites Reinforced with TiB2 Particles

2014 ◽  
Vol 900 ◽  
pp. 141-145 ◽  
Author(s):  
Can Feng Fang ◽  
Guang Xu Liu ◽  
Ling Gang Meng ◽  
Xing Guo Zhang
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Composite Material ◽  
High Temperature ◽  
The Self ◽  
Al Alloy ◽  
Temperature Synthesis ◽  
Microstructure And Mechanical Properties ◽  
High Temperature Synthesis

The effects of in-situ TiB2 particle fabricated from Al-Ti-B system via the self-propagating high-temperature synthesis (SHS) reaction technology on microstructure and mechanical properties of Mg-Sn-Zn-Al alloy were investigated. The results indicate that the size of the Mg2Sn and α-Mg+Mg32(Al,Zn)49 phase becomes coarser with the increasing content of Al-Ti-B preform, meanwhile the amount of eutectic α-Mg+Mg32(Al,Zn)49 phase increases too. The addition of Al-Ti-B is favorable toward promoting the strength of composites, but deteriorates elongation. The resulting as-extruded composite material with 4 wt.% Al-Ti-B preform exhibits good overall mechanical properties with an ultimate tensile strength of 291 MPa and an elongation over 2 %.

Enhancement of mechanical properties of composites made of calcium carbonate modified bamboo fibers and polypropylene

Holzforschung ◽  
2015 ◽  
Vol 69 (2) ◽  
pp. 215-221 ◽  
Author(s):  
Haitao Cheng ◽  
Jie Gao ◽  
Ge Wang ◽  
Sheldon Q. Shi ◽  
Shuangbao Zhang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Aqueous Solution ◽  
Tensile Strength ◽  
Tensile Modulus ◽  
Inorganic Materials ◽  
Polypropylene Composites ◽  
Fiber Treatment ◽  
Bamboo Fibers ◽  
Properties Of Composites

Abstract The work aimed at the improvement of the mechanical properties of bamboo fiber-polypropylene composites (BaFPPC) by treatment of the fibers with CaCO3 at various concentrations of the solution (0.05, 0.1, 0.2, and 0.3 mol l-1). CaCO3 particles were successfully deposited in situ to bamboo fibers by means of ionic reaction of Na2 CO3 and CaCl2 aqueous solution at various temperatures. Then BaFPPC were produced, and various tests on single fibers and the composites were performed. The compatibility between BaF and PP matrix was improved by the treatments. The crystallinity of inorganic materials was significantly affected by the reagent’s concentration. A 10.4% increase in tensile strength and a 16.7% increase in tensile modulus were observed after fiber treatment with CaCO3 at a concentration of 0.2 mol l-1.

Sign in / Sign up

Export Citation Format

Share Document