Trial on C3N4 Coating Cutter Hard-Dry Cutting on Hardened Steel

2010 ◽  
Vol 33 ◽  
pp. 483-486
Author(s):  
Hai Dong Yang ◽  
Xi Quan Xia ◽  
Zhen Hua Qing
Keyword(s):  
Thermal Conductivity ◽  
Wear Resistance ◽  
Friction Coefficient ◽  
Tool Material ◽  
High Hardness ◽  
Hardened Steel ◽  
Hard Material ◽  
Low Friction ◽  
Dry Cutting ◽  
Coated Tool

The method of “cutting instead of grinding” on hardened steel is always attractive to engineers. To gain this aim the tool material must first be found. C3N4 is a new kind of super hard material and has comparable properties with diamond in high hardness, wear-resistance, low friction coefficient and thermal conductivity. A number of dry-cutting tests were carried out by C3N4-film coated tool on hardened steel, proved the coating tool is suitable for hard dry cutting.

Cutting Performance of Al2O3/TiC/TiN Nanocomposite Tools

2010 ◽  
Vol 443 ◽  
pp. 318-323 ◽  
Author(s):  
Han Lian Liu ◽  
Chuan Zhen Huang ◽  
Bin Zou
Keyword(s):  
High Speed ◽  
Cutting Tool ◽  
Tool Material ◽  
High Hardness ◽  
Hardened Steel ◽  
Cutting Performance ◽  
Machining Parameters ◽  
Dry Cutting ◽  
Ceramic Cutting Tool ◽  
Multi Phase

A multi-scale and multi-phase nanocomposite ceramic cutting tool material Al2O3/TiC/TiN(LTN) with high comprehensive mechanical properties has been successfully fabricated by means of adding micro-scale TiC and nano-scale TiN particles. The cutting performance and wear mechanisms of this advanced ceramic cutting tool were researched by turning two kinds of hardened steel 40Cr and T10A respectively. Compared with the commercial ceramic tool LT55, LTN showed a superior wear resistance with certain machining parameters. The machining tests indicated that the new materials tool is suitable for continuously dry cutting of hardened steel with high hardness at high speed.

Quaternary–matrix, nanocomposite self-lubricating PVD coatings in the system TiAlCN-MoS2 – structure and tological properties

2003 ◽  
Vol 788 ◽  
Author(s):  
V. Spassov ◽  
A. Savan ◽  
A. R. Phani ◽  
M. Stueber ◽  
H. Haefke
Keyword(s):  
Friction Coefficient ◽  
High Speed ◽  
High Hardness ◽  
Scratch Test ◽  
Hard Coatings ◽  
Work Piece ◽  
Low Friction ◽  
Dry Cutting ◽  
Productivity Cost ◽  
Temperature Oxidation

ABSTRACTNowadays the demands placed upon the tooling in processes such as cutting, drilling, milling, stamping, bending, etc. are constantly growing and restrictive. On one hand, productivity, cost efficiency and quality all require high-speed processes to be developed. On the other hand, environmental safety requires very little or no lubricant to be used (dry cutting or minimized spray-lubrication). When combined, these two considerations mean: the tool should wear very little, withstand high temperatures and the friction between the tool and the work piece should be minimized. An apparent approach to simultaneously satisfying such requirements is coating the tools with self-lubricating hard coatings. Quaternary TiAlCN is a rapidly developing hard coating suitable for a number of cutting applications. The well-known wear-resistant coating TiN has been demonstrated to have improved high-temperature oxidation resistance when aluminum is included, i.e. TiAl N. Addition of yet a fourth element, carbon, has the primary effect of lowering the high friction coefficient occurring between the ceramic coating and steel. The high hardness, toughness, heat resistance and low friction coefficient of TiAlCN make it the ideal candidate for applications such as milling, hobbing, tapping, stamping and punching. MoS2 is a well-known solid lubricant widely used as tribological coatings, especially for applications working in vacuum or dry environment. Combining the wear resistance of the quaternary TiAlCN matrix with the lubricating properties of MoS2 has an extremely beneficial effect in further improving the tribological performance of the resulting composite. The coatings were deposited on hardmetal (WC-Co) and Si (100) substrates using reactive magnetron sputtering. The structure of the coatings is studied by plain-view TEM and XTEM, electron diffraction and ED X. The tribological properties were examined by Pin-on-Disk (PoD) tribometer. The adhesion was estimated by scratch test, and the hardness was measured by nanoindentation. All the coatings examined had a very low friction coefficient (typically below 0.09) and volumetric wear rate against 100Cr6 steel (AISI 52100) of 7.10-7 mm3/N/m. The relation of deposition parameters to structure to properties is discussed. To the authors knowledge, this is the first paper describing quaternary TiAlCN matrix with inclusions of MoS2.

Tribological Behavior of PTFE Nanocomposites Reinforced with PBA Grafted Alumina Nanoparticles

2012 ◽  
Vol 184-185 ◽  
pp. 1380-1383
Author(s):  
Yong Ping Niu ◽  
Xiang Yan Li ◽  
Jun Kai Zhang ◽  
Ming Han ◽  
Yong Zhen Zhang
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Wear Resistance ◽  
Friction Coefficient ◽  
Tribological Behavior ◽  
Compression Molding ◽  
Alumina Nanoparticles ◽  
Low Friction ◽  
Grafted Nanoparticles ◽  
Scanning Electron

Polybutyl acrylate (PBA) grafted alumina nanoparticles were synthesized. Polytetrafluoroethylene (PTFE) nanocomposites reinforced with PBA grafted nanoparticles were prepared by compression molding. The effects of PBA grafted nanoparticles on the tribological behavior of the PTFE nanocomposites were investigated on a tribometer. The abrasion mechanisms of the PTFE nanocomposites were investigated by scanning electron microscopy (SEM) of the abraded surfaces. The results show that the addition of PBA grafted nanoparticles maintains low friction coefficient and improves the wear resistance of the PTFE nanocomposites.

scholarly journals Multiscale frictional behaviors of sp2 nanocrystallited carbon films with different ion irradiation densities

Friction ◽  
2020 ◽  
Author(s):  
Zelong Hu ◽  
Xue Fan ◽  
Cheng Chen
Keyword(s):  
Friction Coefficient ◽  
Contact Pressure ◽  
Electron Cyclotron Resonance ◽  
Ion Irradiation ◽  
Carbon Film ◽  
High Hardness ◽  
Carbon Films ◽  
Real Contact Area ◽  
Low Friction ◽  
Plasma Sputtering

Abstract sp2 nanocrystallited carbon films with large nanocrystallite sizes, smooth surfaces, and relative high hardness were prepared with different ion irradiation densities regulated with the substrate magnetic coil current in an electron cyclotron resonance plasma sputtering system. Their multiscale frictional behaviors were investigated with macro pin-on-disk tribo-tests and micro nanoscratch tests. The results revealed that, at an ion irradiation density of 16 mA/cm2, sp2 nanocrystallited carbon film exhibits the lowest friction coefficient and good wear resistant properties at both the macroscale and microscale. The film sliding against a Si3N4 ball under a contact pressure of 0.57 GPa exhibited a low friction coefficient of 0.09 and a long wear life at the macroscale. Furthermore, the film sliding against a diamond tip under a contact pressure of 4.9 GPa exhibited a stable low friction coefficient of 0.08 with a shallow scratch depth at the microscale. It is suggested that sp2 nanocrystallites affect the frictional behaviors in the cases described differently. At the macroscale, the contact interface via the small real contact area and the sp2 nanocrystallited transfer layer dominated the frictional behavior, while the sp2 nanocrystallited structure in the film with low shear strength and high plastic resistivity, as well as the smooth surface morphology, decided the steady low nanoscratch properties at the microscale. These findings expand multiscale tribological applications of sp2 nanocrystallited carbon films.

Research on Cutting Performance of Graphite-Like Carbon Coated Tools in Dry Drilling of Ferrous Metal

2010 ◽  
Vol 455 ◽  
pp. 467-471
Author(s):  
Ji Ming Xiao ◽  
Yan Li ◽  
L.J. Bai ◽  
Qi Long Yuan ◽  
Jian Ming Zheng
Keyword(s):  
High Speed ◽  
Ferrous Metal ◽  
High Speed Steel ◽  
High Hardness ◽  
Cutting Performance ◽  
Low Friction ◽  
Dry Cutting ◽  
Coated Tools ◽  
Carbon Coated ◽  
Twist Drills

The graphite-like carbon (GLC) coating was deposited onto high-speed steel (HSS) twist drills by magnetron sputter ion plating technique. The drilling tests were performed on the ferrous metal under dry cutting conditions. By the analysis and comparison of the flank wear and the drilling forces on drills, the cutting performance of GLC coated HSS tools was researched. The results show that GLC coating with high hardness and low friction coefficient, due to its good adhesion and match with HSS substrate, can significantly improve the cutting performance of HSS twist drills, prolong the tool life, decrease the drilling forces in drilling the ferrous metal. And its cutting performance is better than the hard coated drills in the lower speed, but its thermal stability is inferior to the hard coated drills in the higher speed.

Application Experiences in Powder Compaction of Iron Powder - Influence of Tool Material on Tool Life

2007 ◽  
Vol 534-536 ◽  
pp. 649-652
Author(s):  
Odd Sandberg ◽  
Andreas Krona ◽  
Sigurd Berg ◽  
Flemming Kaad ◽  
Göran Nord
Keyword(s):  
Tool Life ◽  
Tool Steel ◽  
Compaction Pressure ◽  
Tool Material ◽  
High Hardness ◽  
Full Potential ◽  
Tool Steels ◽  
Low Friction ◽  
Powder Pressing ◽  
Type Size

Tool steels for powder pressing are normally heat treated to a high hardness to counteract plastic deformation during the compacting process. Ductility and wear resistance of the die punch or core rod are determined by the type, size, amount, hardness and distribution of the hard phase in the martensitic matrix. Thus, tool steels can be designed and optimized for specific powder pressing application. To be able to utilize the full potential of the tool steel, also the design, heat treatment and eventual surface coating of the steel must be taken into account. In this paper new low-friction tool steel is investigated in PM manufacturing for a number of applications. An increase of tool life of more than two times compared to ordinary tool steels is found. Furthermore, the new low friction tool steel shows a potential for sintered parts with higher densities through the applicability of increased compaction pressure or minimized lubricant amount.

Sliding Wear Characteristics and Fabrication of LPS-SIC Ceramic by Sintering Additives

2007 ◽  
Vol 345-346 ◽  
pp. 1541-1544
Author(s):  
Han Ki Yoon ◽  
Sung Ho Park ◽  
Won Jo Park
Keyword(s):  
Friction Coefficient ◽  
Gas Turbines ◽  
Sliding Wear ◽  
Sintering Temperature ◽  
High Hardness ◽  
Wear Loss ◽  
Low Friction ◽  
Wear Characteristics ◽  
Sic Ceramic ◽  
High Temperature Components

Silicon carbide (SiC) materials have been extensively studied for high-temperature components in fusion blanket system and gas turbines, because they have excellent a hightemperature mechanical properties, high thermal conductivity and wear resistance. However, the brittle characteristics of SiC such as low strain-to fracture still impose a severe limitation on the practical application of SiC materials. Therefore, a study of the sliding wear characteristics and fabrication of SiC ceramic by sintering temperature and additives are need. As the result of abrasion, the friction coefficient of the monolithic SiC sintered at 1800°C was the lowest, and the friction coefficient of that sintered at 1760°C was the highest. The monolithic SiC manufactured at 1800°C showed the highest hardness and the lowest friction coefficient. The friction coefficient of the monolithic SiC sintered by the SiO2 contents of 2wt% was the lowest, and the friction coefficient that sintered by the SiO2 contents of 5wt% was the highest. 1800°C of sintering temperature and 2wt% of SiO2 contents ware shown high hardness, low friction coefficient and wear loss compare with other temperatures and SiO2 contents.

Improvement on the Cutting Performance of CVD Diamond Coated Drills in Drilling CFRP

2012 ◽  
Vol 499 ◽  
pp. 366-371 ◽  
Author(s):  
Jian Guo Zhang ◽  
Ben Wang ◽  
Fang Hong Sun ◽  
Hang Gao
Keyword(s):  
Thermal Conductivity ◽  
Wear Resistance ◽  
Diamond Films ◽  
Chemical Vapor ◽  
Cvd Diamond ◽  
Cutting Performance ◽  
Reinforced Plastics ◽  
Coated Tool ◽  
Hot Filament

Carbon fiber reinforced plastics (CFRP) is difficult to machine because of the extremely abrasive nature of the carbon fibers and its low thermal conductivity. CVD diamond films have many excellent properties such as wonderful wear resistance, high thermal conductivity and low friction coefficient, therefore depositing diamond films on the surface of drills is thought to be an effective way to elongate the lifetime of drills and improve the cutting performance. In this study, diamond films are deposited on the WC-Co drill using hot filament chemical vapor deposition (HFCVD) method. The results of characterization by the scanning electron microscope (SEM) and Raman spectrum indicate that the fabricated CVD diamond coated drill is covered with a layer of uniform and high-purity diamond films. The cutting performance of as-fabricated CVD diamond coated drill is evaluated in dry drilling CFRP, comparing with the uncoated WC-Co drill. The results demonstrate that the CVD diamond coated drill exhibits much stronger wear resistance. Its flank wear is about 50μm after drilling 30 holes, about one-third of that of WC-Co drill. Machining quality of the exit and internal wall of drilled holes shows better surface finish obtained by coated drill, which suggests that CVD diamond coated tool has great advantages in drilling CFRP.

Assessment of Tribological Properties of Low Friction Thin Layers Produced by Vacuum Methods

2019 ◽  
Vol 293 ◽  
pp. 125-140
Author(s):  
Agnieszka Paradecka ◽  
Krzysztof Lukaszkowicz ◽  
Jozef Sondor
Keyword(s):  
Wear Resistance ◽  
Friction Coefficient ◽  
Chemical Analysis ◽  
Coefficient Of Friction ◽  
Tribological Properties ◽  
Structural Changes ◽  
Thin Layers ◽  
Low Friction ◽  
Topographic Analysis ◽  
Steel Substrates

Low friction thin layers are an excellent alternative for conventional coatings. They provide increased life of the elements, to which they were applied, due to enhancing the hardness or chemical and electrochemical resistance. They help to avoid the cracks, oxidation, as well as possible structural changes during the element's work. However, they primarily improve tribological properties by increasing wear resistance and reducing the friction. This also applies to components operating under variable conditions such as load, speed, temperature. The presented article analyzes the properties of various low-friction thin layers deposited by vacuum methods on the steel substrates. DLC, TiC, MoS2, CrCN thin layers were chosen, as they achieve the lowest possible coefficient of friction. In the framework of this work the measurements of adhesion of the investigated layers to the substrate as well as the friction coefficient, chemical analysis, microstructure and topographic analysis of the low-friction layers were carried out.

scholarly journals Structural and Mechanical Properties of a-BCN Films Prepared by an Arc-Sputtering Hybrid Process

Materials ◽  
2021 ◽  
Vol 14 (4) ◽  
pp. 719
Author(s):  
Yuki Hirata ◽  
Ryotaro Takeuchi ◽  
Hiroyuki Taniguchi ◽  
Masao Kawagoe ◽  
Yoshinao Iwamoto ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Wear Resistance ◽  
Friction Coefficient ◽  
Carbon Content ◽  
Photoelectron Spectroscopy ◽  
High Hardness ◽  
Film Structure ◽  
Hybrid Process ◽  
High Wear Resistance ◽  
Wear Volume

Amorphous boron carbon nitride (a-BCN) films exhibit excellent properties such as high hardness and high wear resistance. However, the correlation between the film structure and its mechanical properties is not fully understood. In this study, a-BCN films were prepared by an arc-sputtering hybrid process under various coating conditions, and the correlations between the film’s structure and mechanical properties were clarified. Glow discharge optical emission spectroscopy, X-ray photoelectron spectroscopy, Fourier-transform infrared spectroscopy, and Raman spectroscopy were used to analyze the structural properties and chemical composition. Nanoindentation and ball-on-disc tests were performed to evaluate the hardness and to estimate the friction coefficient and wear volume, respectively. The results indicated that the mechanical properties strongly depend on the carbon content in the film; it decreases significantly when the carbon content is <90%. On the other hand, by controlling the contents of boron and nitrogen to a very small amount (up to 2.5 at.%), it is possible to synthesize a film that has nearly the same hardness and friction coefficient as those of an amorphous carbon (a-C) film and better wear resistance than the a-C film.

Sign in / Sign up

Export Citation Format

Share Document