Calculation of Effect of Viscous and Pressure Forces on Trimming Moments

2014 ◽  
Vol 590 ◽  
pp. 42-47
Author(s):  
Salma Sherbaz ◽  
Wen Yang Duan
Keyword(s):  
Computational Methods ◽  
Reasonable Agreement ◽  
Volume Of Fluid ◽  
Wave Profile ◽  
Computational Domain ◽  
Implicit Methods ◽  
Ansys Fluent ◽  
Hull Form ◽  
Experimental Values

In this study the effects of viscous and pressure forces on trimming moments of Series 60 (CB = 0.6) hull form are calculated at different Froude numbers by employing computational methods. The grid generator GAMBIT was used for meshing hull and computational domain. The Simulations are carried out using commercial CFD code ANSYS Fluent 13. The SIMPLE (Semi-Implicit Methods for Pressure-Linked Equations) algorithm is used for pressure-velocity coupling. The volume of Fluid (VOF) formulation is employed. The computed resistance, wave profile and trim of series 60 hull are compared with experimental values and found in reasonable agreement.

scholarly journals APPLICATION OF THE VOLUME OF FLUID METHOD TO SIMULATE THE PROCESS OF MELTING AND MOVEMENT OF FUEL

2022 ◽  
pp. 3-8
Author(s):  
Y. A. Kabdylkakov ◽  
A. S. Suraev
Keyword(s):  
Melting Process ◽  
Volume Of Fluid ◽  
Experimental Device ◽  
Computational Domain ◽  
Two Dimensional ◽  
Volume Of Fluid Method ◽  
Thermal Problem ◽  
Ansys Fluent ◽  
Simulation Results ◽  
Multiphase Fluid

The article considers the possibility of using the method of multiphase fluid Volume of Fluid (VOF), the Ansys Fluent program, for numerical simulation of the melting process of the materials of the experimental device and their movement over the volume of the computational domain. For modeling the design of a typical experimental device tested in the reactor was selected, a two-dimensional computational model was developed, methods for solving the thermal problem were described, and the simulation results were presented.

scholarly journals Predicting the effect of the rib pitch on thermal performance factor of small channels plate heat exchangers fitted with Y and C shapes obstacles

2021 ◽  
Vol 3 (4) ◽  
Author(s):  
Sirine Chtourou ◽  
Hassene Djemel ◽  
Mohamed Kaffel ◽  
Mounir Baccar
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Computer Aided Design ◽  
Flow Characteristics ◽  
Plate Heat Exchanger ◽  
Geometrical Parameters ◽  
Computational Domain ◽  
Ansys Fluent ◽  
Plate Heat ◽  
Small Channels

AbstractThis study presents a numerical analysis of a laminar counter flow inside small channels plate heat exchanger fitted with Y and C shape obstacles. Using the Computational Fluid Dynamics CFD, an advanced and modern simulation technique, the influence of the geometrical parameters (such as geometry, rib pitch) on the flow characteristics, the thermal and the hydrodynamics performance of the PHE (plate heat exchanger) is investigated numerically. The main goal of this work is to increase the flow turbulence, enhance the heat transfer and the thermal efficiency by inserting new obstacles forms. The computational domain is a conjugate model which is developed by the Computer Aided Design CAD software Solidworks. The results, obtained with Ansys Fluent, show that the presence of the shaped ribs provides enhancement in heat transfer and fluid turbulence. The CFD analysis is validated with the previous study. The non-dimensional factors such as the Nusselt number Nu, the skin friction factor Cf and the thermo-hydraulic performance parameter THPP are predicted with a Reynolds number Re range of 200–800. The temperature and the velocity distribution are presented and analyzed. The Y ribs and the C ribs offer as maximum THPP values respectively about 1.44 and 2.6 times of a smooth duct.

scholarly journals Verification and Validation of a Methodology to Numerically Generate Waves Using Transient Discrete Data as Prescribed Velocity Boundary Condition

2021 ◽  
Vol 9 (8) ◽  
pp. 896
Author(s):  
Rafael P. Maciel ◽  
Cristiano Fragassa ◽  
Bianca N. Machado ◽  
Luiz A. O. Rocha ◽  
Elizaldo D. dos Santos ◽  
...  
Keyword(s):  
Boundary Condition ◽  
Numerical Analysis ◽  
Laboratory Experiment ◽  
Ocean Waves ◽  
Discrete Data ◽  
Multiphase Model ◽  
Computational Domain ◽  
Regular Waves ◽  
Ansys Fluent ◽  
Wave Channel

This work presents a two-dimensional numerical analysis of a wave channel and a oscillating water column (OWC) device. The main goal is to validate a methodology which uses transient velocity data as a means to impose velocity boundary condition for the generation of numerical waves. To achieve this, a numerical wave channel was simulated using regular waves with the same parameters as those used in a laboratory experiment. First, these waves were imposed as prescribed velocity boundary condition and compared with the analytical solution; then, the OWC device was inserted into the computational domain, aiming to validate this methodology. For the numerical analysis, computational fluid dynamics ANSYS Fluent software was employed, and to tackle with water–air interaction, the nonlinear multiphase model volume of fluid (VOF) was applied. Although the results obtained through the use of discrete data as velocity boundary condition presented a little disparity; in general, they showed a good agreement with laboratory experiment results. Since many studies use regular waves, there is a lack of analysis with ocean waves realistic data; thus, the proposed methodology stands out for its capacity of using realistic sea state data in numerical simulations regarding wave energy converters (WECs).

scholarly journals Simulation of Thermoplastic Powder Cold Spraying

2021 ◽  
Vol 14 (6) ◽  
pp. 726-734
Author(s):  
Tatyana A. Brusentseva ◽  
◽  
Vladislav S. Shikalov ◽  
Sergei M. Lavruk ◽  
Vasily M. Fomin
Keyword(s):  
Gas Flow ◽  
Experimental Studies ◽  
Cold Spraying ◽  
Deposition Efficiency ◽  
Powder Materials ◽  
Stagnation Temperature ◽  
Computational Domain ◽  
Ansys Fluent ◽  
Process Gas ◽  
Spray Method

The work is devoted to the deposition of composite powder materials by cold spray method. As a spraying material, a thermoplastic compound «WAY» for marking the roadway was used. An asphalt concrete was used as a substrate. As a result of experimental studies, the dependence of the deposition efficiency on the stagnation temperature of the working air in the ejector nozzle was obtained. The ANSYS Fluent package was used for evaluative modeling of the cold spraying process. Gas flow patterns were obtained in the computational domain without particles and taking into account the interaction of the flow with particles. The trajectory of the particles was calculated for various spraying parameters

scholarly journals Energetic Self-Folding Mechanism in α-Helixes

2019 ◽  
Author(s):  
Adolfo Bastida ◽  
José Zúñiga ◽  
Alberto Requena ◽  
Javier Cerezo
Keyword(s):  
Molecular Dynamics ◽  
Potential Energy Surfaces ◽  
Reasonable Agreement ◽  
Dihedral Angles ◽  
Native Conformation ◽  
Experimental Values ◽  
Α Helix ◽  
Dynamics Simulations ◽  
Energy Surfaces ◽  
Large Peptide

A novel energetic route driving the folding of a polyalanine peptide from an extended conformation to its α-helix native conformation is described, supported by a new method to compute mean potential energy surfaces accurately in terms of the dihedral angles of the peptide chain from extensive Molecular Dynamics simulations. The Energetic Self-Folding (ESF) route arises specifically from the balance between the intrinsic propensity of alanine residues towards the α<sub>R </sub>conformation and two, opposite, effects: the destabilizing interaction with neighbor residues and the stabilizing formation of native hydrogen bonds, with the latter being dominant for large peptide lengths. The ESF mechanism provides simple but robust support to the nucleation-elongation, or zipper models, and offers a quantitative energetic funnel picture of the folding process. The mechanism is validated by the reasonable agreement between the computed folding energies and the experimental values.

Numerical Research of the Effect of the Outlet Diameter of Diffuser on the Performance and the Radial Force in a Single-Stage Centrifugal Pump

2014 ◽  
Author(s):  
Jiang Wei ◽  
Li Guojun ◽  
Liu Pengfei ◽  
Zhang Lisheng ◽  
Qing Hongyang
Keyword(s):  
Centrifugal Pump ◽  
Radial Force ◽  
Numerical Results ◽  
Operating Conditions ◽  
Single Stage ◽  
Navier Stokes ◽  
Computational Domain ◽  
Ansys Fluent ◽  
Vaned Diffuser ◽  
Unsteady Numerical Simulation

In this paper, a single-stage pump with diffuser vanes of different outlet diameters has been investigated both numerically and experimentally. The influence of the diffuser vane outlet diameter on pump hydraulic performance and on the radial force of the impeller is explored. Pumps equipped with three different diffusers but with impellers and volutes of the same parameters were simulated by 3D Navier-Stokes solver ANSYS-FLUENT in order to study the effect of the outlet diameter of vaned diffuser on performance of the centrifugal pump. Structured grids of high quality were applied on the whole computational domain. Experimental results were acquired by prototype experiments and were then compared with the numerical results. Both experimental and numerical results show that the performance of a pump with a diffuser of smaller outlet diameter is better than of bigger outlet diameter under all operating conditions. The radial force imposed on the impeller obtained by unsteady numerical simulation was analyzed. The results also indicated that an appropriate decrease in the outlet diameter of the diffuser vane could increase the radial force.

scholarly journals WAVE PRESSURE DISTRIBUTIONS ON A U-OWC BREAKWATER: EXPERIMENTAL DATA VS CFD MODEL

2018 ◽  
pp. 15
Author(s):  
Pasquale G. Fabio Filianoti ◽  
Luana Gurnari
Keyword(s):  
Pressure Distribution ◽  
High Performance ◽  
Ideal Gas ◽  
Navier Stokes ◽  
Eastern Coast ◽  
Computational Domain ◽  
Ansys Fluent ◽  
Wave Energy Converters ◽  
Vof Model ◽  
Line Force

U-OWCs are Wave Energy Converters belong in to the family of Oscillating Water Column. The interaction between waves and a U-OWC breakwater produces an unknown pressure distribution on the breakwater wall, due to the motion inside the plant. In order to evaluate the force acting on a U-OWC breakwater produced by regular waves, we carried out an experiment in a 2D numerical flume. The computational domain is equipped by a piston-type wavemaker, in the left extremity side and a U-OWC breakwater on the opposite side. The water-air interaction is taken into account by means of the Volume Of Fluid (VOF) model implemented in the commercial CFD code Ansys Fluent. Both air and water flow fields are assumed to be unsteady and are computed by solving the Reynolds-Averaged Navier-Stokes (RANS) equations. In the numerical model, air is considered as an ideal gas, in order to take into account the compressibility inside the plenum chamber. Results were compared with a theoretical model on a traditional vertical breakwater and experimental results obtained through an experiment directly at sea, off the beach of Reggio Calabria, in the eastern coast of the Straits of Messina (Southern Italy). As observed in the physical experiment at sea, the pressure distribution are strongly influenced by the absorption of the plant. Indeed, in case of high performance of the U-OWC, we found a deformation of the pressure distribution in respect to the theoretical one, especially near the outer opening of the plant. This deformation produces a lower in line force on the structure.

Volume of Fluid (VOF) Analysis of Oil-Jet Lubrication for High-Speed Spur Gears Using an Adaptive Meshing Approach

2015 ◽  
Author(s):  
Tommaso Fondelli ◽  
Antonio Andreini ◽  
Riccardo Da Soghe ◽  
Bruno Facchini ◽  
Lorenzo Cipolla
Keyword(s):  
High Speed ◽  
Numerical Study ◽  
Adaptive Mesh ◽  
Spur Gear ◽  
Volume Of Fluid ◽  
Adaptive Meshing ◽  
Ansys Fluent ◽  
Injection Angle ◽  
Gear Teeth ◽  
Oil Jet

In high speed gearbox systems, the lubrication is generally provided using nozzles to create small oil jets that feed oil into the meshing zone. It is essential that the gear teeth are properly lubricated and that enough oil gets into the tooth spaces to permit sufficient cooling and prevent gearbox failure. A good understanding of the oil behaviour inside the gearbox is therefore desirable, to minimize lubrication losses and reduce the oil volume involved, and ensure gearbox reliability. In order to reach these objectives, a comprehensive numerical study of a single oil jet impinging radially on a single spur gear teeth has been carried out using the Volume of Fluid (VOF) method. The aims of this study are to evaluate the resistant torque produced by the oil jet lubrication, and to develop a physical understanding of the losses deriving from the oil-gear interaction, studying the droplets and ligaments formation produced by the breaking up of the jet as well as the formation of an oil film on the surface of the teeth. URANS calculations have been performed with the commercial code ANSYS FLUENT and an adaptive mesh approach has been developed as a way of significantly reducing the simulation costs. This method allows an automatic mesh refinement and/or coarsening at the air-oil interface based on the volume of fluid gradient, increasing the accuracy of the predictions of oil break-up as well as minimizing numerical diffusion of the interface. A global sensitivity analysis of adopted models has been carried out and a numerical set-up has been defined. Finally several simulations varying the oil injection angle have been performed, in order to evaluate how this parameter affects the resistant torque and the lubrication performances.

The Influence of Thermodynamic Properties of Alloys on Effective Interdiffusion Coefficients in Ternary Systems

2007 ◽  
Vol 263 ◽  
pp. 141-146 ◽  
Author(s):  
Ü. Ugaste ◽  
Tony Laas ◽  
T. Škled-Gorbatšova
Keyword(s):  
Thermodynamic Properties ◽  
Diffusion Coefficients ◽  
Reasonable Agreement ◽  
Ternary Systems ◽  
Tracer Diffusion ◽  
Diffusion Couples ◽  
Experimental Values ◽  
Tracer Diffusion Coefficients ◽  
Interdiffusion Coefficients ◽  
The Relationship

To prove the validity of Dayananda’s phenomenological model of interdiffusion in ternary systems the effective interdiffusion coefficients for a few diffusion couples in the system Cu-Ni-Fe, annealed at 1000 oC, are calculated on the basis of this model using available tracer diffusion and thermodynamic data. It is found that the calculated values of effective interdiffusion coefficients are in reasonable agreement with experimental values extracted independently from experimental concentration--penetration curves. Using the relationship between effective interdiffusion coefficients, tracer diffusion coefficients and thermodynamic factors, it is shown that thermodynamic properties of alloys play a significant role in interdiffusion processes in the system Cu-Fe-Ni.

Rates of detritiation of the strychninesulfonic acids at the 11-position in alkaline solution

1984 ◽  
Vol 62 (11) ◽  
pp. 2448-2450 ◽  
Author(s):  
John T. Edward ◽  
Sin Cheong Wong ◽  
A. J. Kresge ◽  
M. F. Powell
Keyword(s):  
Ionic Strength ◽  
Sodium Hydroxide ◽  
Alkaline Solution ◽  
Reasonable Agreement ◽  
Sulfonate Group ◽  
Experimental Values

Tritium was incorporated into the 11-position of strychnine, and of strychninesulfonic acids-I, -II, and -III, and the rate of detritiation from the four compounds in 0.5 M sodium hydroxide at 25 °C was measured. Rates were reduced by the negative sulfonate groups, the extent of reduction varying inversely with the distance of the sulfonate group from the negative oxygen of the enolate intermediate. Experimental rates were in reasonable agreement with values expected at zero ionic strength from the Kirkwood–Westheimer equation. The problem of correcting experimental values for the effect of ionic strength is discussed.

Sign in / Sign up

Export Citation Format

Share Document