Combined Cycle Units – An Alternative to Reciprocating Engines in Terrestrial Propulsion Field - Estimation of Performances

2014 ◽  
Vol 659 ◽  
pp. 289-294 ◽  
Author(s):  
Dan Teodor Balanescu ◽  
Vlad Mario Homutescu ◽  
Pavel Doru Vasiliu ◽  
Constantin Eusebiu Hritcu
Keyword(s):  
Power Plants ◽  
Fossil Fuels ◽  
Pressure Ratio ◽  
Combined Cycle ◽  
Advanced Technology ◽  
Small Scale ◽  
Feed Water ◽  
Compressor Pressure Ratio ◽  
Marine Propulsion ◽  
Field Estimation

Currently, Combined Cycle Power Plants represent the most advanced technology in the domain of high and medium power generation units operating with fossil fuels. Consequently, the interest for their implementation in the propulsion systems field is justified. At this moment, Combined Cycle Units are used for propulsion only on ships (marine propulsion). The present study goes one step further by referring to a small scale Combined Cycle Unit configured for operation as terrestrial propulsion system and based on a two-pressure-levels Steam Cycle. The performances of this unit are analyzed function by the compressor pressure ratio and HRSG feed water temperature.

Genetic Optimization of Steam Injected Gas Turbine Power Plants

2002 ◽  
Author(s):  
Ibrahim Sinan Akmandor ◽  
O¨zhan O¨ksu¨z ◽  
Sec¸kin Go¨kaltun ◽  
Melih Han Bilgin
Keyword(s):  
Gas Turbine ◽  
Power Output ◽  
Thermal Efficiency ◽  
Gas Turbines ◽  
Power Plants ◽  
Pressure Ratio ◽  
Steam Injection ◽  
Combined Cycle ◽  
Inlet Temperature ◽  
Compressor Pressure Ratio

A new methodology is developed to find the optimal steam injection levels in simple and combined cycle gas turbine power plants. When steam injection process is being applied to simple cycle gas turbines, it is shown to offer many benefits, including increased power output and efficiency as well as reduced exhaust emissions. For combined cycle power plants, steam injection in the gas turbine, significantly decreases the amount of flow and energy through the steam turbine and the overall power output of the combined cycle is decreased. This study focuses on finding the maximum power output and efficiency of steam injected simple and combined cycle gas turbines. For that purpose, the thermodynamic cycle analysis and a genetic algorithm are linked within an automated design loop. The multi-parameter objective function is either based on the power output or on the overall thermal efficiency. NOx levels have also been taken into account in a third objective function denoted as steam injection effectiveness. The calculations are done for a wide range of parameters such as compressor pressure ratio, turbine inlet temperature, air and steam mass flow rates. Firstly, 6 widely used simple and combined cycle power plants performance are used as test cases for thermodynamic cycle validation. Secondly, gas turbine main parameters are modified to yield the maximum generator power and thermal efficiency. Finally, the effects of uniform crossover, creep mutation, different random number seeds, population size and the number of children per pair of parents on the performance of the genetic algorithm are studied. Parametric analyses show that application of high turbine inlet temperature, high air mass flow rate and no steam injection lead to high power and high combined cycle thermal efficiency. On the contrary, when NOx reduction is desired, steam injection is necessary. For simple cycle, almost full amount of steam injection is required to increase power and efficiency as well as to reduce NOx. Moreover, it is found that the compressor pressure ratio for high power output is significantly lower than the compressor pressure ratio that drives the high thermal efficiency.

Solar Upgrading of Fuels for Generation of Electricity

2001 ◽  
Vol 123 (2) ◽  
pp. 160-163 ◽  
Author(s):  
Rainer Tamme ◽  
Reiner Buck ◽  
Michael Epstein ◽  
Uriyel Fisher ◽  
Chemi Sugarmen
Keyword(s):  
Gas Turbines ◽  
Large Scale ◽  
Fossil Fuels ◽  
High Efficiency ◽  
Combined Cycle ◽  
Test Facility ◽  
Small Scale ◽  
Start Up ◽  
Efficiency Conversion ◽  
Solar Field

This paper presents a novel process comprising solar upgrading of hydrocarbons by steam reforming in solar specific receiver-reactors and utilizing the upgraded, hydrogen-rich fuel in high efficiency conversion systems, such as gas turbines or fuel cells. In comparison to conventionally heated processes about 30% of fuel can be saved with respect to the same specific output. Such processes can be used in small scale as a stand-alone system for off-grid markets as well as in large scale to be operated in connection with conventional combined-cycle plants. The complete reforming process will be demonstrated in the SOLASYS project, supported by the European Commission in the JOULE/THERMIE framework. The project has been started in June 1998. The SOLASYS plant is designed for 300 kWel output, it consists of the solar field, the solar reformer and a gas turbine, adjusted to operate with the reformed gas. The SOLASYS plant will be operated at the experimental solar test facility of the Weizmann Institute of Science in Israel. Start-up of the pilot plant is scheduled in April 2001. The midterm goal is to replace fossil fuels by renewable or non-conventional feedstock in order to increase the share of renewable energy and to establish processes with only minor or no CO2 emission. Examples might be upgrading of bio-gas from municipal solid waste as well as upgrading of weak gas resources.

Parameterization of High Solar Share Gas Turbine Systems

2012 ◽  
Author(s):  
Stephan Heide ◽  
Christian Felsmann ◽  
Uwe Gampe ◽  
Sven Boje ◽  
Bernd Gericke ◽  
...  
Keyword(s):  
Gas Turbine ◽  
Power Plants ◽  
Planning Process ◽  
Pressure Ratio ◽  
Thermal Power ◽  
Combined Cycle ◽  
Process Models ◽  
Solar Thermal ◽  
Thermal Power Plants ◽  
Solar Thermal Power

Existing solar thermal power plants are based on steam turbine cycles. While their process temperature is limited, solar gas turbine (GT) systems provide the opportunity to utilize solar heat at a much higher temperature. Therefore there is potential to improve the efficiency of future solar thermal power plants. Solar based heat input to substitute fuel requires specific GT features. Currently the portfolio of available GTs with these features is restricted. Only small capacity research plants are in service or in planning. Process layout and technology studies for high solar share GT systems have been carried out and have already been reported by the authors. While these investigations are based on a commercial 10MW class GT, this paper addresses the parameterization of high solar share GT systems and is not restricted to any type of commercial GT. Three configurations of solar hybrid GT cycles are analyzed. Besides recuperated and simple GT with bottoming Organic Rankine Cycle (ORC), a conventional combined cycle is considered. The study addresses the GT parameterization. Therefore parametric process models are used for simulation. Maximum electrical efficiency and associated optimum compressor pressure ratio πC are derived at design conditions. The pressure losses of the additional solar components of solar hybrid GTs have a different adversely effect on the investigated systems. Further aspects like high ambient temperature, availability of water and influence of compressor pressure level on component design are discussed as well. The present study is part of the R&D project Hybrid High Solar Share Gas Turbine Systems (HYGATE) which is funded by the German Ministry for the Environment, Nature and Nuclear Safety and the Ministry of Economics and Technology.

Performance Evaluation of a Small Scale High Efficiency Cogeneration System

2006 ◽  
Author(s):  
Mauro Reini
Keyword(s):  
High Efficiency ◽  
Pressure Ratio ◽  
Organic Rankine Cycle ◽  
Thermodynamic Cycle ◽  
Rankine Cycle ◽  
Combined Cycle ◽  
Working Fluid ◽  
Small Scale ◽  
Performance Parameters ◽  
Cogeneration System

In recent years, a big effort has been made to improve microturbines thermal efficiency, in order to approach 40%. Two main options may be considered: i) a wide usage of advanced materials for hot ends components, like impeller and recuperator; ii) implementing more complicated thermodynamic cycle, like combined cycle. In the frame of the second option, the paper deals with the hypothesis of bottoming a low pressure ratio, recuperated gas cycle, typically realized in actual microturbines, with an Organic Rankine Cycle (ORC). The object is to evaluate the expected nominal performance parameters of the integrated-combined cycle cogeneration system, taking account of different options for working fluid, vapor pressure and component’s performance parameters. Both options of recuperated and not recuperated bottom cycles are discussed, in relation with ORC working fluid nature and possible stack temperature for microturbine exhaust gases. Finally, some preliminary consideration about the arrangement of the combined cycle unit, and the effects of possible future progress of gas cycle microturbines are presented.

Model of a Combined Cycle Steam Section for Use in an On-Line Fuzzy-Based Diagnosis System

2012 ◽  
Author(s):  
Rafael Barbosa ◽  
Sandro Ferreira ◽  
Raphael Duarte ◽  
Paula Ribeiro Pinto ◽  
Marília Paula e Silva
Keyword(s):  
Power Plant ◽  
Power Plants ◽  
Computer Models ◽  
Combined Cycle ◽  
Feed Water ◽  
Diagnosis System ◽  
Power Plant Equipment ◽  
Partial Load ◽  
On Line ◽  
Good Agreement

In recent years, combined cycle power plants showed remarkable progress in the safe operation and reliability of their equipment, mostly because of the reliable control and instrumentation systems available today. However, these systems cannot detect and evaluate inconsistencies in the behaviour of equipment due to failures and avoid trips caused by catastrophic events. Computer models developed to simulate the power plant equipment are often employed in diagnosis tools in order to provide accurate healthy parameters that are compared to the field measured parameters. In this work, the computer models built for the simulation of some of the main bottoming cycle equipment of a real power plant (steam turbine, HRSG, boiler feed water pumps and condenser) are described. These models were developed through characteristics maps and constitutive equations related to the fluid path analysis, implemented in Fortran language. The results provided by the developed models for each equipment show good agreement with operational data at base and partial load in simulations that covered a good part of the load domain. Due to the good agreement between the measured parameters values and those calculated through simulation, these models are intended to be included in an on-line fuzzy-based diagnosis system.

Effect of Deaerator Parameters on Simple and Reheat Gas/Steam Combined Cycle With Different Cooling Medium

2019 ◽  
Author(s):  
Mayank Maheshwari ◽  
Onkar Singh
Keyword(s):  
Gas Turbine ◽  
Mass Fraction ◽  
Power Plants ◽  
Performance Enhancement ◽  
Pressure Ratio ◽  
Combined Cycle ◽  
Cycle Performance ◽  
Inlet Temperature ◽  
Operating Pressure ◽  
Cooling Medium

Abstract Performance of gas/steam combined cycle power plants relies upon the performance exhibited by both gas based topping cycle and steam based bottoming cycle. Therefore, the measures for improving the performance of the gas turbine cycle and steam bottoming cycle eventually result in overall combined cycle performance enhancement. Gas turbine cooling medium affects the cooling efficacy. Amongst different parameters in the steam bottoming cycle, the deaerator parameter also plays its role in cycle performance. The present study analyzes the effect of deaerator’s operating pressure being varied from 1.6 bar to 2.2 bar in different configurations of simple and reheat gas/steam combined cycle with different cooling medium for fixed cycle pressure ratio of 40, turbine inlet temperature of 2000 K and ambient temperature of 303 K with varying ammonia mass fraction from 0.6 to 0.9. Analysis of the results obtained for different combined cycle configuration shows that for the simple gas turbine and reheat gas turbine-based configurations, the maximum work output of 643.78 kJ/kg of air and 730.87 kJ/kg of air respectively for ammonia mass fraction of 0.6, cycle efficiency of 54.55% and 53.14% respectively at ammonia mass fraction of 0.7 and second law efficiency of 59.71% and 57.95% respectively at ammonia mass fraction of 0.7 is obtained for the configuration having triple pressure HRVG with ammonia-water turbine at high pressure and intermediate pressure and steam turbine operating at deaerator pressure of 1.6 bar.

scholarly journals Performance Analysis With Different Means of Cooling in a Combined Cycle

1995 ◽  
Author(s):  
Onkar Singh ◽  
R. Yadav
Keyword(s):  
Gas Turbine ◽  
Power Plants ◽  
Pressure Ratio ◽  
Combined Cycle ◽  
Inlet Temperature ◽  
Optimum Pressure ◽  
Cooling Medium ◽  
Cooling Technology ◽  
Improved Performance ◽  
Topping Cycle

Combined cycle based power plants and their development and application for energy efficient base load power generation necessitates enforced cooling to maintain the topping cycle gas turbine blade temperature at permissible levels, attributed to the increased turbine inlet temperature and compressor pressure ratio, for the improved performance and reliability of combined cycle. The mathematical model based on expansion path inside gas turbine considering dilution of mainstream and aerodynamic mixing losses for a range of cooling medium has been developed based on internal, film, transpiration cooling technologies and a combination of these. It is found that the appreciation of a cycle configuration as well as the optimum pressure ratio and peak temperature vary significantly with types of cooling technology adopted. Steam cooling for rotor appears to be a very potential cooling medium, when employed with an appropriate cooling technology. This paper deals with the thermodynamic analysis of turbine cooling using, different means of cooling i.e. air, water and steam.

scholarly journals Advanced Aeroderivative Gas Turbines in Coal-Based High Performance Power Systems (HIPPS)

1998 ◽  
Author(s):  
F. L. Robson ◽  
D. J. Seery
Keyword(s):  
Power Systems ◽  
Gas Turbine ◽  
Gas Turbines ◽  
High Performance ◽  
Power Plants ◽  
Performance Standards ◽  
Combined Cycle ◽  
Advanced Technology ◽  
Early 21St Century ◽  
Near Term

The Department of Energy’s Federal Energy Technology Center (FETC) is sponsoring the Combustion 2000 Program aimed at introducing clean and more efficient advanced technology coal-based power systems in the early 21st century. As part of this program, the United Technologies Research Center has assembled a seven member team to identify and develop the technology for a High Performance Power Systems (HIPPS) that will provide in the near term, 47% efficiency (HHV), and meet emission goals only one-tenth of current New Source Performance Standards for coal-fired power plants. In addition, the team is identifying advanced technologies that could result in HIPPS with efficiencies approaching 55% (HHV). The HIPPS is a combined cycle that uses a coal-fired High Temperature Advanced Furnace (HITAF) to preheat compressor discharge air in both convective and radiant heaters. The heated air is then sent to the gas turbine where additional fuel, either natural gas or distillate, is burned to raise the temperature to the levels of modern gas turbines. Steam is raised in the HITAF and in a Heat Recovery Steam Generator for the steam bottoming cycle. With state-of-the-art frame type gas turbines, the efficiency goal of 47% is met in a system with more than two-thirds of the heat input furnished by coal. By using advanced aeroderivative engine technology, HIPPS in combined-cycle and Humid Air Turbine (HAT) cycle configurations could result in efficiencies of over 50% and could approach 55%. The following paper contains descriptions of the HIPPS concept including the HITAF and heat exchangers, and of the various gas turbine configurations. Projections of HIPPS performance, emissions including significant reduction in greenhouse gases are given. Application of HIPPS to repowering is discussed.

Parameter Optimization on Combined Gas Turbine-Fuel Cell Power Plants

2005 ◽  
Vol 2 (4) ◽  
pp. 268-273 ◽  
Author(s):  
Rainer Kurz
Keyword(s):  
Fuel Cell ◽  
Gas Turbine ◽  
Power Plants ◽  
Pressure Ratio ◽  
Design Parameters ◽  
Turbine Efficiency ◽  
Compressor Pressure Ratio ◽  
Turbine Design ◽  
Cycle Efficiency ◽  
Compressor Efficiency

A thermodynamic model for a gas turbine-fuel cell hybrid is created and described in the paper. The effects of gas turbine design parameters such as compressor pressure ratio, compressor efficiency, turbine efficiency, and mass flow are considered. The model allows to simulate the effects of fuel cell design parameters such as operating temperature, pressure, fuel utilization, and current density on the cycle efficiency. This paper discusses, based on a parametric study, optimum design parameters for a hybrid gas turbine. Because it is desirable to use existing gas turbine designs for the hybrids, the requirements for this hybridization are considered. Based on performance data for a typical 1600hp industrial single shaft gas turbine, a model to predict the off-design performance is developed. In the paper, two complementary studies are performed: The first study attempts to determine the range of cycle parameters that will lead to a reasonable cycle efficiency. Next, an existing gas turbine, that fits into the previously established range of parameters, will be studied in more detail. Conclusions from this paper include the feasibility of using existing gas turbine designs for the proposed cycle.

Effect of Bottoming Cycle Alternatives on the Performance of Combined Cycle

2003 ◽  
Author(s):  
R. Yadav
Keyword(s):  
Gas Turbine ◽  
Pressure Ratio ◽  
Positive Influence ◽  
Combined Cycle ◽  
Exhaust Temperature ◽  
Compressor Pressure Ratio ◽  
Topping Cycle ◽  
Steam Parameters ◽  
Cycle Efficiency ◽  
Steam Cycle

The increase in efficiency of combined cycle has mainly been caused by the improvements in gas turbine cycle efficiency. With the increase in firing temperature the exhaust temperature is substantially high around 873 K for moderate compressor pressure ratio, which has positive influence on steam cycle efficiency. Minimizing the irreversibility within the heat recovery steam generator HRSG and choosing proper steam cycle configuration with optimized steam parameters improve the steam cycle efficiency and thus in turn the combined cycle efficiency. In this paper, LM9001H gas turbine, a state of art technology turbine with modified compressor pressure ratio has been chosen as a topping cycle. Various bottoming cycles alternatives (sub-critical) coupled with LM9001H topping cycle with and without recuperation such as dual and triple pressure steam cycles with and without reheat have been chosen to predict the performance of combined cycle.

Sign in / Sign up

Export Citation Format

Share Document