Friction Characteristics with Pin-on-Disc Friction Test on Microstructured Surface Using Whirling Electrical Discharge Texturing

2014 ◽  
Vol 1017 ◽  
pp. 417-422
Author(s):  
Vitchuda Lertphokanont ◽  
Takayuki Sato ◽  
Masahiro Oi ◽  
Minoru Ota ◽  
Keishi Yamaguchi ◽  
...  
Keyword(s):  
Friction Coefficient ◽  
Electrical Discharge ◽  
Area Ratio ◽  
Mixed Lubrication ◽  
Optimal Conditions ◽  
Friction Test ◽  
Crater Diameter ◽  
Microstructured Surface ◽  
Pin On Disc ◽  
Lubrication Condition

A microstructured surface was created on a steel surface by whirling electrical discharge texturing (WEDT) since it was considered that the microstructures could act as lubricant reservoirs to assist the formation of a lubricating film, resulting in reduced friction. In this study, friction tests under engine oil were carried out over a range of loads and sliding speeds. In addition, the surface characteristics of the microstructured surface were also investigated to optimize the friction characteristics of the textured surface through pin-on-disc friction tests. It was found that under the mixed lubrication condition near the boundary condition, textured surfaces with texture-area ratio of approximately 6% and a mean crater diameter of 35 μm were considered as the optimal conditions for reducing the friction coefficient. However, a texture-area ratio of approximately 4% and a mean crater diameter of 35 μm were considered as the optimal conditions for reducing the friction coefficient under the mixed lubrication condition near the elastohydrodynamic lubrication condition. It was considered that when the normal load decreased, the lubrication region changed from the mixed lubrication condition to the hydrodynamic lubrication condition, which meant that the actual contact surface area decreased. The decrease in the actual contact surface area with decreasing texture-area ratio led to a reduction in the friction coefficient. Finally, it was clarified that the friction coefficient was reduced under the optimized conditions of the microstructured surface through a pin-on-disc friction test.

scholarly journals Micro-Structuring on Cylindrical Inner Surface Using Whirling Electrical Discharge Texturing

2012 ◽  
Vol 565 ◽  
pp. 430-435 ◽  
Author(s):  
Vitchuda Lertphokanont ◽  
Takayuki Sato ◽  
Minoru Ota ◽  
Keishi Yamaguchi ◽  
Kai Egashira
Keyword(s):  
Friction Coefficient ◽  
Electrical Discharge ◽  
Area Ratio ◽  
Crater Depth ◽  
Tool Electrode ◽  
Textured Surface ◽  
Feed Speed ◽  
Total Removal ◽  
Crater Diameter ◽  
Micro Structuring

The authors developed Whirling Electrical Discharge Texturing (WEDT) in order to reduce friction coefficient of cylinder-shaped parts. In previous research, the authors verified fundamental characteristics of WEDT by observation of textured surface. It was found that a crater shape and texture-area ratio can be controlled by WEDT. The texture-area ratio depends on feed speed of tool electrode. In this research, crater depth, crater diameter, texture area ratio and total removal volume of craters were investigated to confirm characteristics of WEDT in detail. In addition, tungsten wire was used as a whirling shaft in order to improve stability of whirling phenomenon. Moreover, a textured surface was finished by lapping-film in order to remove protrusions around craters and reduce friction coefficient. As a result, it was verified that the texture-area ratio slightly increased with decreasing feed speed and it was confirmed that crater depth, crater diameter, and total removal volume of craters were also related to feed speed.

Numerical Prediction of Surface Wear and Roughness Parameters During Running-In for Line Contacts Under Mixed Lubrication

2018 ◽  
Vol 140 (6) ◽  
Author(s):  
Yazhao Zhang ◽  
Alexander Kovalev ◽  
Noriyuki Hayashi ◽  
Kensuke Nishiura ◽  
Yonggang Meng
Keyword(s):  
Friction Coefficient ◽  
Contact Region ◽  
Mixed Lubrication ◽  
Asperity Contact ◽  
Wear Particles ◽  
Wear Model ◽  
Wear Process ◽  
Line Contacts ◽  
Lubrication Condition ◽  
Initial Line

A stochastic model for predicting the evolutions of wear profile and surface height probability density function (PDF) of initial line contacts during running-in under mixed lubrication condition is presented. A numerical approach was developed on the basis of stochastic solution of mixed lubrication, which combined the Patir and Cheng's average flow model for calculation of the hydrodynamic pressure and the Kogut and Etsion's (KE) rough surface contact model for calculation of the asperity contact pressure. The total friction force was assumed to be the sum of the boundary friction at the contact asperities and the integration of viscous shear stress in the hydrodynamic region. The wear depth on the contact region was estimated according to the modified Archard's wear model using the asperity contact pressure. Sugimura's wear model was modified and used to link the wear particle size distribution and the variation of surface height PDF during wear. In the wear process, the variations of profile and surface height PDF of initial line contacts were calculated step by step in time, and the pressure distribution, friction coefficient, and wear rate were updated consequently. The effect of size distribution of wear particles on the wear process was numerically investigated, and the simulation results showed that the lubrication condition in which small wear particles are generated from the asperity contact region is beneficial to reduce friction coefficient and wear rate, and leads to a better steady mixed lubrication condition.

Effect of Discharge Duration and Pulse Frequency on Surface Characteristics Using Whirling Electrical Discharge Texturing

2014 ◽  
Vol 8 (4) ◽  
pp. 561-568 ◽  
Author(s):  
Vitchuda Lertphokanont ◽  
◽  
Masahiro Oi ◽  
Takayuki Sato ◽  
Minoru Ota ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Electrical Discharge ◽  
Surface Characteristics ◽  
Pulse Frequency ◽  
Area Ratio ◽  
Textured Surface ◽  
Optimum Conditions ◽  
Total Removal ◽  
Crater Diameter ◽  
Discharge Duration

Discharge duration and pulse frequency are studied to determine the optimum conditions for creating a single crater. In addition, the relationships between pulse frequency and surface characteristics using Whirling Electrical Discharge Texturing (WEDT) are determined. It is confirmed that the texture-area ratio and the total removal volume of craters, but not crater diameter or crater depth, can be controlled by adjusting pulse frequency. Moreover, after honing, surface characteristics decrease owing to the removal of protrusions. With honing, the surface roughness of the textured surface leads to a reduced friction coefficient as expected.

The comprehensive effect of surface texture and roughness under hydrodynamic and mixed lubrication conditions

2017 ◽  
Vol 231 (10) ◽  
pp. 1307-1319 ◽  
Author(s):  
Chenbo Ma ◽  
Yanjun Duan ◽  
Bo Yu ◽  
Jianjun Sun ◽  
Qiaoan Tu
Keyword(s):  
Surface Roughness ◽  
Friction Coefficient ◽  
Hydrodynamic Lubrication ◽  
Diameter Ratio ◽  
Mixed Lubrication ◽  
Textured Surface ◽  
Texture Parameters ◽  
Lubrication Condition ◽  
Lubrication Conditions ◽  
Effect Of Surface

A theoretical study is carried out to investigate the comprehensive effect of the machined roughness and fabricated textures, by solving the average Reynolds equation coupled with a mass-conservative cavitation algorithm and taking into account asperity contact. We analyzed the influence of surface roughness, which is represented by the combined root-mean-square roughness σ and surface pattern parameter γ on the optimum texture parameters including the dimple depth-over-diameter ratio and area density under hydrodynamic and mixed lubrication conditions. The results show that the effect of surface roughness on load-carrying capacity can be ignored under hydrodynamic lubrication condition. Furthermore, the optimum texture parameters under hydrodynamic lubrication condition and the optimum dimple depth-over-diameter ratio under mixed lubrication condition are determined at minimized friction coefficient, which can be taken as the same for smooth-textured surface and rough-textured surface. The corresponding minimum friction coefficient increases with increasing σ and γ, and decreasing dimple area density under mixed lubrication condition.

Friction Characteristics of Poly(vinyl Alcohol) Hydrogel as an Articular Cartilage Biomaterial

2007 ◽  
Vol 330-332 ◽  
pp. 1297-1300 ◽  
Author(s):  
Yu Song Pan ◽  
Dang Sheng Xiong ◽  
Xiao Lin Chen
Keyword(s):  
Stainless Steel ◽  
Articular Cartilage ◽  
Friction Coefficient ◽  
Vinyl Alcohol ◽  
Steel Ball ◽  
Poly Vinyl Alcohol ◽  
Friction Test ◽  
Stainless Steel Ball ◽  
Lubrication Condition ◽  
Pva Hydrogel

Poly(vinyl alcohol) (PVA) hydrogel is a promising articular cartilage biomaterial. In this paper, the effects of different variable factors on the friction coefficient of Poly(vinyl alcohol) (PVA) hydrogel were investigated when sliding against stainless steel ball by ball-pan tribometer. Factors included lubrication condition, sliding speed, diameter of stainless steel ball, and load. It was shown that the free water in PVA hydrogel has an excellent lubrication on the counterparts. The friction coefficients have little difference between dry and lubricants lubrication condition at initial friction test. With the friction test time prolonged, friction coefficient of PVA hydrogel under dry condition increased rapidly. Friction coefficient decreased with the increase of sliding speed and the diameter of stainless steel ball, and increased with the increasing load. The rising rate of friction coefficient at low load region is obviously larger than that at high load region.

Frictional behaviour of engineering surfaces in overall lubrication regimes of point contacts

2011 ◽  
Vol 225 (11) ◽  
pp. 1071-1080 ◽  
Author(s):  
S Wang ◽  
Y-Z Hu ◽  
Q-C Tan
Keyword(s):  
Friction Coefficient ◽  
Contact Area ◽  
Area Ratio ◽  
Mixed Lubrication ◽  
Point Contacts ◽  
Friction Behaviour ◽  
True Contact Area ◽  
Contact Area Ratio ◽  
True Contact ◽  
Frictional Behaviour

The aim of the present paper is to study experimentally and numerically the frictional behaviour of engineering surfaces within all lubrication regions of point contacts. For this reason, a numerical solution proposed elsewhere by the current authors, which can predict friction under the different lubrication modes of elastohydrodynamic, mixed, and boundary lubrications, is introduced. Based on a deterministic model of mixed lubrication, the solution was combined with the variation of the lubricating films’ physical state during the transition of lubrication modes. Results show that roughness amplitude has a great effect on the transition of friction regimes. In addition, it is also observed that variation of the friction coefficient has nearly the same trend as the true contact area ratio in the mixed lubrication state. Meanwhile, it is concluded that transverse roughness has better film-forming capacity than longitudinal roughness and thus leads to a lower magnitude of friction coefficient if the operating conditions are the same. Analysis of the mechanism of friction behaviour suggests that the true contact area ratio determines the friction behaviour of engineering surfaces in mixed lubrication. In smooth contacts, the comparison of experiment tests and simulation results suggests that friction variation results from gradual change of the liquid lubricant to solid-like matter with diminishing film thickness.

scholarly journals The Impact of Heat Treatment on the Behavior of a Hot-Dip Zinc Coating Applied to Steel During Dry Friction

Materials ◽  
2021 ◽  
Vol 14 (3) ◽  
pp. 660
Author(s):  
Dariusz Jędrzejczyk ◽  
Elżbieta Szatkowska
Keyword(s):  
Heat Treatment ◽  
Wear Resistance ◽  
Friction Coefficient ◽  
Dry Friction ◽  
Zinc Coating ◽  
Pin On Disc ◽  
The One ◽  
The Impact ◽  
Coating Hardness ◽  
Anticorrosion Properties

The analyzed topic refers to the wear resistance and friction coefficient changes resulting from heat treatment (HT) of a hot-dip zinc coating deposited on steel. The aim of research was to evaluate the coating behavior during dry friction after HT as a result of microstructure changes and increase the coating hardness. The HT parameters should be determined by taking into consideration, on the one hand, coating wear resistance and, on the other hand, its anticorrosion properties. A hot-dip zinc coating was deposited in industrial conditions (according EN ISO 10684) on disc-shaped samples and the chosen bolts. The achieved results were assessed on the basis of tribological tests (T11 pin-on-disc tester, Schatz®Analyse device, Sindelfingen, Germany), microscopic observations (with the use of optical and scanning microscopy), EDS (point and linear) analysis, and microhardness measurements. It is proved that properly applied HT of a hot-dip zinc coating results in changes in the coating’s microstructure, hardness, friction coefficient, and wear resistance.

Comparison in Tribological Properties of YBa2Cu3OX/Ag and Bi2Sr2CaCu2OX/Ag Self-Lubricating Composites

2011 ◽  
Vol 291-294 ◽  
pp. 34-40
Author(s):  
Hua Tang ◽  
Wen Jing Li ◽  
Chang Sheng Li
Keyword(s):  
Friction Coefficient ◽  
Tribological Properties ◽  
Room Temperature ◽  
Superconducting Transition ◽  
Friction Test ◽  
Average Value ◽  
Structure And Morphology ◽  
Disk Friction ◽  
Pin On Disk ◽  
Self Lubricating Composites

The YBa2Cu3Ox/Ag and Bi2Sr2CaCu2Ox/Ag self-lubricating composites were prepared using powder metallurgic method. The crystal structure and morphology of the as-synthesized samples were characterized by XRD and SEM. The YBa2Cu3Ox/Ag and Bi2Sr2CaCu2Ox/Ag self-lubricating composites were found to compose of superconductor phase and Ag phase. The tribological properties from ultra-low temperature to room temperature of the composites were studied by pin-on-disk friction test. It was found that the friction coefficients of pure YBa2Cu3Ox(YBCO) and Bi2Sr2CaCu2Ox(BSCCO) were both dropped abruptly when the temperature cooled below the superconducting transition temperature. At room temperature, the friction coefficient of pure YBa2Cu3Oxis 0.68~0.95, when mixing 15wt% Ag, the friction coefficient of the sample decreased to the lowest value 0.11. The friction coefficient of pure Bi2Sr2CaCu2Ox is 0.15~0.17, When Ag content reach 10wt%, the coefficient was lowest (average value is 0.13). The addition of appropriate amount of Ag obviously improve the tribological property of YBCO, while only slightly meliorate that of BSCO. On the other hand, the YBCO/Ag composites exhibit better tribological properties than BSCCO/Ag composites at higher load under the same experimental condition.

INFLUENCE OF NITROGEN FLOW RATE ON FRICTION COEFFICIENT AND SURFACE ROUGHNESS OF TiN COATINGS DEPOSITED ON TOOL STEEL USING ARC METHOD

2007 ◽  
Vol 14 (05) ◽  
pp. 1007-1013 ◽  
Author(s):  
ESAH HAMZAH ◽  
ALI OURDJINI ◽  
MUBARAK ALI ◽  
PARVEZ AKHTER ◽  
MOHD RADZI HJ. MOHD TOFF ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Friction Coefficient ◽  
Tool Steel ◽  
Flow Rate ◽  
Physical Vapor Deposition ◽  
Gas Flow ◽  
Cutting Tools ◽  
Gas Flow Rate ◽  
Pin On Disc ◽  
The Coefficient Of Friction

In the present study, the effect of various N 2 gas flow rates on friction coefficient and surface roughness of TiN -coated D2 tool steel was examined by a commercially available cathodic arc physical vapor deposition (CAPVD) technique. A Pin-on-Disc test was carried out to study the Coefficient of friction (COF) versus sliding distance. A surface roughness tester measured the surface roughness parameters. The minimum values for the COF and surface roughness were recorded at a N 2 gas flow rate of 200 sccm. The increase in the COF and surface roughness at a N 2 gas flow rate of 100 sccm was mainly attributed to an increase in both size and number of titanium particles, whereas the increase at 300 sccm was attributed to a larger number of growth defects generated during the coating process. These ideas make it possible to optimize the coating properties as a function of N 2 gas flow rate for specific applications, e.g. cutting tools for automobiles, aircraft, and various mechanical parts.

Sign in / Sign up

Export Citation Format

Share Document