Fast Adsorption of Erythromycin on the Conjugated Microporous Polymers

2014 ◽  
Vol 1073-1076 ◽  
pp. 32-38
Author(s):  
Chun Li Zheng ◽  
Miao Miao Du ◽  
Yu Zhou Rong
Keyword(s):  
Adsorption Process ◽  
Order Model ◽  
Water Separation ◽  
Film Diffusion ◽  
Microporous Polymers ◽  
Solvent Water ◽  
Surface Areas ◽  
Pseudo Second Order ◽  
Kinetics Of ◽  
Conjugated Microporous Polymers

As a kind of ideal porous absorbents with tunable porosity, large surface areas, and hydrophobicity, conjugated microporous polymers (CMPs) have recently received extensive attention in oil/organic solvent-water separation. However, reports on the application of CMPs in adsorption of erythromycin (ERY) from water are very few. In this work, the adsorption of ERY by three kinds of CMPs was firstly studied. It was observed that all the CMPs extracted ERY quickly from water. The adsorption kinetics of ERY on the three CMPs was well expressed by the pseudo-second-order model, and the adsorption process was found to be mainly controlled by film diffusion. Increasing surface area of the CMPs resulted in greater extent of adsorption. This work may provide fundamental guidance for removal of antibiotics by CMPs.

Study on the Formaldehyde Adsorption Kinetics of Dry Waters

2014 ◽  
Vol 809-810 ◽  
pp. 907-911
Author(s):  
Jun Long Wang ◽  
Jie Hou ◽  
Ting Jiang ◽  
Yong Jun He ◽  
Yao Dong Liang
Keyword(s):  
Adsorption Kinetics ◽  
High Speed ◽  
Adsorption Process ◽  
Average Diameter ◽  
Adsorption Rate ◽  
Absorption Kinetics ◽  
Order Model ◽  
Pseudo Second Order ◽  
Kinetics Of ◽  
Formaldehyde Adsorption

Dry waters with an average diameter of 82 μm were prepared by a high speed mixed route. The formaldehyde absorption kinetics of dry waters was investigated by simulating indoor formaldehyde pollution in glass chamber. The results showed that pseudo-second order model could be used to simulate the adsorption process; the adsorption rate was highest in the initial 60 minutes; when the adsorption lasted for 180 minutes, the adsorption reached equilibrium.

scholarly journals Removal of lead(II) ions by an adsorption process with the use of an advanced SiO2/lignin biosorbent

2017 ◽  
Vol 19 (1) ◽  
pp. 48-53 ◽  
Author(s):  
Łukasz Klapiszewski ◽  
Przemysław Bartczak ◽  
Tomasz Szatkowski ◽  
Teofil Jesionowski
Keyword(s):  
Experimental Data ◽  
Contact Time ◽  
Adsorption Process ◽  
Langmuir Model ◽  
Order Model ◽  
Multifunctional Material ◽  
Pseudo Second Order ◽  
Kinetics Of ◽  
Maximal Sorption Capacity ◽  
Optimal Ph

Abstract We demonstrate here that lignin can be successfully combined with silica to create a multifunctional material with considerable sorption capabilities. Experiments were carried out in which a silica/lignin hybrid was used for the removal of lead(II) ions from water solutions. Adsorption kinetics were also determined and preliminary regeneration tests were performed. The effectiveness of the adsorption process depends on the following parameters: contact time of adsorbent and adsorbate (equilibrium times: 5 min for concentration 25 mg/L, 10 min for 50 and 75 mg/L, 60 min for 100 mg/L), pH (optimal pH = 5) and adsorbent mass. The kinetics of the adsorption of lead(II) ions on the SiO2/lignin biosorbent are best described by a pseudo-second-order model. Adsorption isotherms of lead(II) ions were also determined. The experimental data were found to be in agreement with the Langmuir model, and the maximal sorption capacity of the adsorbent with respect to lead(II) was 89.02 mg/g.

Adsorption Kinetics of Pb2+ Ions Using Chitosan Nanoparticles

2013 ◽  
Vol 367 ◽  
pp. 45-49
Author(s):  
Ying Hong ◽  
Ze Hui Zhong ◽  
You Shi Liu
Keyword(s):  
Adsorption Kinetics ◽  
Chitosan Nanoparticles ◽  
Second Order ◽  
Isotherm Model ◽  
Order Model ◽  
Adsorption Characteristics ◽  
Pseudo Second Order ◽  
Kinetics Of ◽  
Second Order Model

Chitosan nanoparticles were prepared by crosslinkingusing TPP. SEM showed that chitosan nanoparticles were successfully obtained.The adsorption characteristics of chitosan nanoparticles were evaluated. Theresults demonstrated that chitosan nanoparticles were suitable for adsorbent toremoval Pb2+. The parameters for the adsorption of Pb2+by chitosan nanoparticles were also determined. It was shown that chitosannanoparticles were fit for Langmuir’s isotherm model and that the adsorptionkinetics of Pb2+ described by the pseudo-second-order model could bebest.

scholarly journals ADSORPTION AND KINETIC STUDIES OF A NATURAL DYE FROM CURCUMA LONGA L., ONTO BAMBOO YARN

2017 ◽  
Vol 2 (1) ◽  
pp. 13-26
Author(s):  
Tengku Khamanur Azma Tg. Mohd Zamri ◽  
Mimi Sakinah Abd Munaim ◽  
Zularisam Ab Wahid
Keyword(s):  
Adsorption Process ◽  
Regression Coefficient ◽  
Curcuma Longa ◽  
Freundlich Isotherm ◽  
Kinetic Studies ◽  
Natural Dye ◽  
Isotherm Models ◽  
Order Model ◽  
Dyeing Process ◽  
Pseudo Second Order

Natural dye extracted from the rhizome of Curcuma longa L. were applied to bamboo yarns using exhaustion dyeing process. This study investigates the dyeing behaviour of Curcumin; the major color component isolated from rhizomes of Curcuma longa L.on bamboo yarn. Langmuir, Freundlich, Tempkin and Dubinin-Radushkevich isotherm models were used to test the adsorption process of curcumin on bamboo yarn. Comparison of regression coefficient value indicated that the Freundlich isotherm most fitted to the adsorption of curcumin onto bamboo yarn. Furthermore, the kinetics study on this research fitted the pseudo-second order model which indicates that the basis of interaction was chemical adsorption.

scholarly journals Adsorption of strontium on different sodium-enriched bentonites

2017 ◽  
Vol 82 (4) ◽  
pp. 449-463 ◽  
Author(s):  
Sanja Marinovic ◽  
Marija Ajdukovic ◽  
Natasa Jovic-Jovicic ◽  
Tihana Mudrinic ◽  
Bojana Nedic-Vasiljevic ◽  
...  
Keyword(s):  
Cation Exchange ◽  
Adsorption Capacity ◽  
Textural Properties ◽  
X Ray Diffraction ◽  
Order Model ◽  
Surface Areas ◽  
Alkaline Conditions ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order ◽  
Ph Range

Bentonites from three different deposits (Wyoming, TX, USA and Bogovina, Serbia) with similar cation exchange capacities were sodium enriched and tested as adsorbents for Sr2+ in aqueous solutions. X-Ray diffraction analysis confirmed successful Na-exchange. The textural properties of the bentonite samples were determined using low-temperature the nitrogen physisorption method. Significant differences in the textural properties between the different sodium enriched bentonites were found. Adsorption was investigated with respect to adsorbent dosage, pH, contact time and the initial concentration of Sr2+. The adsorption capacity increased with pH. In the pH range from 4.0?8.5, the amount of adsorbed Sr2+ was almost constant but 2?3 times smaller than at pH ?11. Further experiments were performed at the unadjusted pH since extreme alkaline conditions are environmentally hostile and inapplicable in real systems. The adsorption capacity of all the investigated adsorbents toward Sr2+ was similar under the investigated conditions, regardless of significant differences in the specific surface areas. It was shown and confirmed by the Dubinin?Radushkevich model that the cation exchange mechanism was the dominant mechanism of Sr2+ adsorption. Their developed microporous structures contributed to the Sr2+ adsorption process. The adsorption kinetics obeyed the pseudo-second-order model. The isotherm data were best fitted with the Langmuir isotherm model.

scholarly journals Equilibrium and Kinetic Study of Lead and Copper Ion Adsorption on Chitosan-Grafted-Polyacrylic Acid Synthesized by Surface Initiated Atomic Transfer Polymerization

Molecules ◽  
2018 ◽  
Vol 23 (9) ◽  
pp. 2218 ◽  
Author(s):  
Carlos Grande-Tovar ◽  
William Vallejo ◽  
Fabio Zuluaga
Keyword(s):  
Adsorption Capacity ◽  
Polyacrylic Acid ◽  
Adsorption Process ◽  
Kinetic Constant ◽  
Copper Ion ◽  
Toxic Metal ◽  
Maximum Adsorption Capacity ◽  
Order Model ◽  
Equilibrium Studies ◽  
Pseudo Second Order

In this work, we synthesized chitosan grafted-polyacrylic acid (CS-g-PA) through surface-initiated atom transfer radical polymerization (SI-ATRP). We also studied the adsorption process of copper and lead ions onto the CS-g-PA surface. Adsorption equilibrium studies indicated that pH 4.0 was the best pH for the adsorption process and the maximum adsorption capacity over CS-g-PA for Pb2+ ions was 98 mg·g−1 and for Cu2+ it was 164 mg·g−1, while for chitosan alone (CS), the Pb2+ adsorption capacity was only 14.8 mg·g−1 and for Cu2+ it was 140 mg·g−1. Furthermore, the adsorption studies indicated that Langmuir model describes all the experimental data and besides, pseudo-second-order model was suitable to describe kinetic results for the adsorption process, demonstrating a larger kinetic constant of the process was larger for Pb2+ than Cu2+. Compared to other adsorbents reported, CS-g-PA had comparable or even superior adsorbent capacity and besides, all these results suggest that the new CS-g-PA polymers had potential as an adsorbent for hazardous and toxic metal ions produced by different industries.

scholarly journals Enhanced removal of hexavalent chromium by different acid-modified biochar derived from corn straw: behavior and mechanism

2020 ◽  
Vol 81 (10) ◽  
pp. 2270-2280
Author(s):  
Yonggang Xu ◽  
Tianxia Bai ◽  
Yubo Yan ◽  
Yunfeng Zhao ◽  
Ling Yuan ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Hydrogen Ion ◽  
Corn Straw ◽  
Order Model ◽  
Freundlich Model ◽  
X Ray ◽  
Modified Biochar ◽  
Before And After ◽  
Pseudo Second Order ◽  
Kinetics Of

Abstract It is of great significance to remove Cr(VI) from water as a result of its high toxicity. Biochar from corn straw was modified by different acids (HNO3, H2SO4 and H3PO4) to remove Cr(VI) from aqueous solution. To estimate the removal mechanisms of Cr(VI) by the acid-modified biochars, batch experiments were performed in the light of contact time, Cr(VI) concentration, and pH, and the characteristics of acid-modified biochars before and after Cr(VI) adsorption were investigated by Fourier transform infrared spectra (FTIR) and X-ray photoelectron spectroscopy (XPS). The adsorption kinetics of Cr(VI) by acid-modified biochars were consistent with the pseudo-second-order model, and the adsorption isotherm obeyed the Freundlich model. Furthermore, the acid- modified biochars could supply more oxygen-containing functional groups (-COOH and -OH) as electron donor (e−) and hydrogen ion (H+) to enhance the reduction of Cr(VI) to Cr(III), resulting in enhanced removal of Cr(VI). HNO3-modified biochar exhibited the highest removal efficiency of Cr(VI). In general, the acid modifition of biochar was an effective method to increase the removal of Cr(VI).

scholarly journals Adsorption purification of waste water from chromium by ferrite manganese

2020 ◽  
Vol 168 ◽  
pp. 00026
Author(s):  
Liliia Frolova ◽  
Mykola Kharytonov ◽  
Iryna Klimkina ◽  
Oleksandr Kovrov ◽  
Andrii Koveria
Keyword(s):  
Adsorption Process ◽  
Uv Spectroscopy ◽  
Second Order ◽  
Waste Waters ◽  
Equilibrium Isotherms ◽  
X Ray ◽  
First Order ◽  
Freundlich Isotherms ◽  
Pseudo Second Order ◽  
Kinetics Of

Plasma method is used to synthesize manganese ferrite. The basic properties of ferrite are determined by IR spectroscopy, UV spectroscopy, X-ray phase analysis, vibration magnetometry. The paper shows that the use of magnetically controlled sorbent allows to purify waste waters from chromium (III). The process of adsorption of chromium cations (III) is investigated. The kinetics of the process is studied. To describe the equilibrium isotherms, the experimental data are analysed by the models of Langmuir, Freundlich isotherms. Pseudo-first order, pseudo-second-order, and Weber-Morris are used to elucidate the kinetic parameters and mechanism of the adsorption process. It has been established that the removal of Cr (III) cations is described by the pseudo-second order of the Langmuir reaction and mechanism.

scholarly journals Synthesis Fe3O4/Talc nanocomposite by coprecipition-ultrasonication method and advances in hexavalent chromium removal from aqueous solution

2020 ◽  
Vol 38 (9-10) ◽  
pp. 483-501
Author(s):  
Nguyen Thi Huong ◽  
Nguyen Ngoc Son ◽  
Vo Hoang Phuong ◽  
Cong Tien Dung ◽  
Pham Thi Mai Huong ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Adsorption Process ◽  
Low Cost ◽  
Batch Experiments ◽  
X Ray Diffraction ◽  
Order Model ◽  
X Ray ◽  
Pseudo Second Order ◽  
Ft Ir ◽  
Langmuir And Freundlich Equations

The Fe3O4/Talc nanocomposite was synthesized by the coprecipitation-ultrasonication method. The reaction was carried out under a inert gas environment. The nanoparticles were characterized by X-ray diffraction (XRD), field-emission scanning electron microscopy (FESEM), fourier-transform infrared spectroscopy (FT-IR) and vibrating sample magnetometry techniques (VSM), the surface area of the nanoparticles was determined to be 77.92 m2/g by Brunauer-Emmett-Teller method (BET). The kinetic data showed that the adsorption process fitted with the pseudo-second order model. Batch experiments were carried out to determine the adsorption kinetics and mechanisms of Cr(VI) by Fe3O4/Talc nanocomposite. The adsorption process was found to be highly pH-dependent, which made the material selectively adsorb these metals from aqueous solution. The isotherms of adsorption were also studied using Langmuir and Freundlich equations in linear forms. It is found that the Langmuir equation showed better linear correlation with the experimental data than the Freundlich. The thermodynamics of Cr(VI) adsorption onto the Fe3O4/Talc nanocomposite indicated that the adsorption was exothermic. The reusability study has proven that Fe3O4/Talc nanocomposite can be employed as a low-cost and easy to separate.

scholarly journals Kinetics of scandium recovery by TVEX-TBP from the solution formed after the salt chlorinator cake leaching

2020 ◽  
Vol 168 ◽  
pp. 00050
Author(s):  
Vadym Korovin ◽  
Yurii Pohorielov ◽  
Yurii Shestak ◽  
Oleksandr Valiaiev ◽  
Jose Luis Cortina
Keyword(s):  
Chemical Interaction ◽  
Extraction Process ◽  
Second Order ◽  
Order Kinetic ◽  
Order Model ◽  
Elovich Equation ◽  
Diffusion Phase ◽  
Leaching Solution ◽  
Pseudo Second Order ◽  
Kinetics Of

Kinetics of scandium recovery by TVEX containing tributyl phosphate was studied from the clarified leaching solution of salt chlorinator cake. To assess the contribution of each diffusion phase, experimental data were analyzed using a graphic method. To define the contribution of chemical interaction into the scandium extraction process, recovery kinetics was quantitatively described using pseudo-first order, pseudo-second order kinetic models and Elovich equation in linearized form. It was established that recovery kinetics was most accurately described with the pseudo-second-order model.

Sign in / Sign up

Export Citation Format

Share Document