Small Size Specimens Methods for Evaluation of Mechanical Properties

2015 ◽  
Vol 1127 ◽  
pp. 1-8
Author(s):  
Martin Rund ◽  
Josef Volák ◽  
Miroslava Šindelářová
Keyword(s):  
Mechanical Properties ◽  
Small Volume ◽  
Fem Simulation ◽  
Tensile Tests ◽  
Fatigue Tests ◽  
Life Assessment ◽  
Small Scale ◽  
Residual Service Life ◽  
Local Properties ◽  
The Individual

The evaluation of actual mechanical properties of the in-service structures after some time of operation or determination of local properties for detailed FEM simulation yields the necessity to obtain relevant material data with high accuracy from small volume of the experimental material. Therefore, non-destructive or semi-destructive techniques using small size samples are being developed. The use of small-scale samples also enables the evaluation of material properties in various locations of tested component; for example, the mechanical properties of the individual regions of welds, local properties determination for properties anisotropy assessment and properties determination in cases when small volume of the experimental material is available e.g. residual service life assessment of in service components, bulk nanostructured materials… There are shown results of small size tensile tests (M-TT) and small sized fatigue tests (SFT). In the case of small size specimens testing a machining becomes more pronounced that in the case of standard sized specimens. The current study brings information on the machining influence on the expected results obtained by small size specimens in the case of quasi-static tensile tests and fatigue test.

scholarly journals Mechanical Properties of Spruce Wood Extracted from GLT Beams Loaded by Fire

2021 ◽  
Vol 13 (10) ◽  
pp. 5494
Author(s):  
Lucie Kucíková ◽  
Michal Šejnoha ◽  
Tomáš Janda ◽  
Jan Sýkora ◽  
Pavel Padevět ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
High Temperature ◽  
Cross Section ◽  
Negative Impact ◽  
Tensile Tests ◽  
Thermal Recovery ◽  
Bending Test ◽  
Small Scale ◽  
Spruce Wood ◽  
The Impact

Heating wood to high temperature changes either temporarily or permanently its physical properties. This issue is addressed in the present contribution by examining the effect of high temperature on residual mechanical properties of spruce wood, grounding on the results of full-scale fire tests performed on GLT beams. Given these tests, a computational model was developed to provide through-thickness temperature profiles allowing for the estimation of a charring depth on the one hand and on the other hand assigning a particular temperature to each specimen used subsequently in small-scale tensile tests. The measured Young’s moduli and tensile strengths were accompanied by the results from three-point bending test carried out on two groups of beams exposed to fire of a variable duration and differing in the width of the cross-section, b=100 mm (Group 1) and b=160 mm (Group 2). As expected, increasing the fire duration and reducing the initial beam cross-section reduces the residual bending strength. A negative impact of high temperature on residual strength has also been observed from simple tensile tests, although limited to a very narrow layer adjacent to the charring front not even exceeding a typically adopted value of the zero-strength layer d0=7 mm. On the contrary, the impact on stiffness is relatively mild supporting the thermal recovery property of wood.

scholarly journals Changing in Fatigue Life of 300 M Bainitic Steel After Laser Carburizing and Plasma Nitriding

2018 ◽  
Vol 165 ◽  
pp. 21002 ◽  
Author(s):  
Antonio J. Abdalla ◽  
Douglas Santos ◽  
Getúlio Vasconcelos ◽  
Vladimir H. Baggio-Scheid ◽  
Deivid F. Silva
Keyword(s):  
Mechanical Properties ◽  
Fatigue Life ◽  
Plasma Nitriding ◽  
Fatigue Behavior ◽  
High Strength ◽  
Tensile Tests ◽  
Steel Sample ◽  
Fatigue Tests ◽  
300M Steel ◽  
Structural Applications

In this work 300M steel samples is used. This high-strength steel is used in aeronautic and aerospace industry and other structural applications. Initially the 300 M steel sample was submitted to a heat treatment to obtain a bainític structure. It was heated at 850 °C for 30 minutes and after that, cooled at 300 °C for 60 minutes. Afterwards two types of surface treatments have been employed: (a) using low-power laser CO2 (125 W) for introducing carbon into the surface and (b) plasma nitriding at a temperature of 500° C for 3 hours. After surface treatment, the metallographic preparation was carried out and the observations with optical and electronic microscopy have been made. The analysis of the coating showed an increase in the hardness of layer formed on the surface, mainly, among the nitriding layers. The mechanical properties were analyzed using tensile and fatigue tests. The results showed that the mechanical properties in tensile tests were strongly affected by the bainitic microstructure. The steel that received the nitriding surface by plasma treatment showed better fatigue behavior. The results are very promising because the layer formed on steel surface, in addition to improving the fatigue life, still improves protection against corrosion and wear.

Mechanical Properties of Flat Braided Composites With a Circular Hole

1999 ◽  
Author(s):  
Takeru Ohki ◽  
Shinya Ikegaki ◽  
Ken Kurasiki ◽  
Hiroyuki Hamada ◽  
Masaharu Iwamoto
Keyword(s):  
Mechanical Properties ◽  
Tensile Test ◽  
Circular Hole ◽  
Fracture Behavior ◽  
Fatigue Property ◽  
Tensile Tests ◽  
Fatigue Tests ◽  
Braided Composites ◽  
Static Tensile ◽  
The One

Abstract In this study, fracture behavior and strength in the flat braided bar with a circular hole were investigated by static and fatigue test. Two type of specimens were prepared. They are a braided flat bar with an integrally-formed braided hole and a braided flat bar with a machined hole. Moreover, we also examined a specimen that had a metal pin inserted at the circular hole. This specimen was subjected to a static tensile test. The results of the tensile tests indicate that the strength of the flat bar with a braided hole was larger than that of the one with the machined hole. Furthermore, from the results of the fatigue tests, the flat bar with the braided hole showed higher fatigue property than that of the one with the machined hole.

Fatigue Properties of 3D Welded Thin Structures

2020 ◽  
Author(s):  
Seyed M. Allameh ◽  
Avery Lenihan ◽  
Roger Miller ◽  
Hadi Allameh
Keyword(s):  
Mechanical Properties ◽  
3D Printing ◽  
Fatigue Testing ◽  
Interfacial Area ◽  
Tensile Tests ◽  
Orientation Dependence ◽  
Fatigue Tests ◽  
Fatigue Properties ◽  
Mig Welding ◽  
Welded Structures

Abstract Additive manufacturing technology has matured enough to produce real industrial components. A newer method of 3D printing is the deposition of molten metal beads using a MIG weld torch. This involves a 3D printer equipped with a MIG torch layering the metals in desired shapes. It allows the fabrication of components made of MIG weld wires, currently available from various elements including Cu, Al, steel and alloys. Some of these structures made by 3D welding will have applications in critical load bearing conditions. The reliability of such components will be vital in applications where human lives are at stake. Tensile tests are conducted to verify the required strength of the fabricated parts which will undergo monotonic loading; however, fatigue tests are required for cases where cyclic loading will take place. Conventional tensile and fatigue testing requires macro-scale samples. With MIG welding, it is possible to make thin-walled structures. Fatigue testing on samples extracted from thin walls is made possible by microtesting. This study is focused on the mechanical properties of 3D welded structures made from MIG welding wires. Our earlier results showed orientation dependence of mechanical properties in 3D welded structures. They also showed the effect of substrates in expression of the orientation dependence. Welding on metal substrate produces weld beads that are harder at the substrate interfacial area. However, for structures welded on ceramics, the opposite is true. They exhibit a softer substrate interfacial area and a relatively harder top. Our newer results show fatigue properties of structures made by 3D welding. Microsamples measuring 0.2 mm × 0.2 mm × 1.0 mm were extracted from metal beads using a CNC mill along with an EDM. The contours of the samples were machined by milling and the back side was cut by electro discharge machining. Specimens were then polished to the desired size and mounted in the grippers of an E1000 Instron load frame. WaveMatrix® application software from Instron was used to control the machine and to obtain testing data. Fatigue tests were performed, and life cycles were determined for various stress levels up to over 5 million cycles. The preliminary results of tensile tests of these samples show strength levels that are comparable to those of parent metal, in the range of 600–950MPa. Results of fatigue tests show high fatigue lives associated with relatively high stresses. The preliminary results will be presented and the implications of the use of 3D welded rebar in 3D printing of reinforced concrete structures will be discussed.

Fatigue Properties of Al-Li Plates Joined by Friction Stir Welding

2008 ◽  
Vol 385-387 ◽  
pp. 849-852 ◽  
Author(s):  
Pasquale Cavaliere ◽  
Francesco W. Panella ◽  
Antonio Squillace
Keyword(s):  
Mechanical Properties ◽  
Cross Sections ◽  
Testing Machine ◽  
Rolling Direction ◽  
Tensile Tests ◽  
Fatigue Tests ◽  
Control Mode ◽  
Fatigue Properties ◽  
Amplitude Control ◽  
Friction Stir

Al-Li alloys are characterized by a strong anisotropy in mechanical properties and microstructure with respect to the rolling direction. Plates of 2198 Al-Li alloy were friction stir welded by employing maximum rotation speed: 1000 rev/min and welding speed of 80 mm/min, both in parallel and orthogonal directions with respect to the rolling one. The joints mechanical properties were evaluated by means of tensile tests at room temperature. In addition, fatigue tests performed with a resonant electro-mechanical testing machine under constant amplitude control up to 250 Hz loading, were conducted in axial control mode with R(σmin/σmax)=0.33, for all the welding and rotating speed conditions. The fatigue crack propagation experiments were performed by employing single edge notched specimens.With the aim to characterize the weld performances, both the microstructure evolution at jointed cross sections, related to the welding variables, and the fractured surfaces were respectively analyzed by means of optical and scanning electron microscopy.

Mechanical Properties of Flat Braided Composites With a Circular Hole

2000 ◽  
Vol 122 (4) ◽  
pp. 420-424 ◽  
Author(s):  
Takeru Ohki ◽  
Shinya Ikegaki ◽  
Ken Kurasiki ◽  
Hiroyuki Hamada ◽  
Masaharu Iwamoto
Keyword(s):  
Mechanical Properties ◽  
Tensile Test ◽  
Circular Hole ◽  
Fracture Behavior ◽  
Fatigue Property ◽  
Tensile Tests ◽  
Fatigue Tests ◽  
Braided Composites ◽  
Static Tensile ◽  
The One

In this study, fracture behavior and strength in the flat braided bar with a circular hole were investigated by static and fatigue test. Two types of specimen were prepared. They are a braided flat bar with an integrally formed braided hole and a braided flat bar with a machined hole. Moreover, we also examined a specimen that had a metal pin inserted at the circular hole. This specimen was subjected to a static tensile test. The results of the tensile tests indicate that the strength of the flat bar with a braided hole was larger than that of the one with the machined hole. Furthermore, from the results of the fatigue tests, the flat bar with the braided hole showed higher fatigue property than that of the one with the machined hole. [S0094-4289(00)02604-9]

scholarly journals Influence of Oxygen on the Fatigue Behaviour of Ti-6Al-7Nb Alloy

2016 ◽  
Vol 704 ◽  
pp. 44-52 ◽  
Author(s):  
Alexandra Amherd Hidalgo ◽  
Thomas Ebel ◽  
Wolfgang Limberg ◽  
Florian Pyczak
Keyword(s):  
Mechanical Properties ◽  
Oxygen Content ◽  
Treatment Time ◽  
Light And Electron Microscopy ◽  
Tensile Tests ◽  
Fatigue Behaviour ◽  
Fatigue Tests ◽  
Four Point Bending ◽  
Initiation And Propagation ◽  
Effect Of Oxygen

One of the challenges in PM Ti alloys is to control the impurities level. Oxygen affects the microstructure and the mechanical properties of titanium alloys. Ti-6Al-7Nb is a promising alloy to use in PM due to its outstanding biocompatibility and mechanical properties required for load bearing medical implants. In this work, the influence of the impurities content on the ductility, fatigue resistance and microstructure of Ti-6Al-7Nb alloy processed by metal injection moulding was examined. Tensile and fatigue specimens were manufactured using Ti-6Al-7Nb gas atomized powder. Depending on the thermal treatment time, various oxygen contents were introduced into the specimens. The resulting oxygen content was determined by melt extraction technique. Tensile tests and high cycle four-point bending fatigue tests at room temperature were performed. First studies about the effect of oxygen content on crack initiation and propagation were done by the observation of microstructures and fractured surfaces using light and electron microscopy (SEM).

Mechanical Properties and Microstructure of AZ Magnesium Alloys Anodized by Phosphate Electrolyte

2010 ◽  
Vol 654-656 ◽  
pp. 771-774
Author(s):  
Teruto Kanadani ◽  
Shuji Hikino ◽  
Atsushi Saijo ◽  
Makoto Hino ◽  
Koji Murakami ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Magnesium Alloys ◽  
Fatigue Cracks ◽  
Tensile Tests ◽  
Fatigue Tests ◽  
Phosphate Solution ◽  
Hardness Tests ◽  
Die Cast ◽  
Structural Applications ◽  
Good Creep Resistance

Magnesium alloys possess many advantageous functional properties. Use of magnesium alloys, mainly for vehicle parts as well as electronic appliances, has been booming in recent years because of their lightweight compared to aluminum alloys and good creep resistance relative to plastics. Most the use of magnesium for structural applications has been die-cast components and most of this in one alloy, AZ91D. Since magnesium has the lowest electrochemical potential out of all the common commercial metals and is extremely prone to corrosion, it is necessary that it undergoes surface treatment. It is well known that fatigue cracks start near the free surface. Surface microstructure, therefore, should have a significant effect on the fatigue strength. This study was carried out using a mainly phosphate solution without heavy metal onto various AZ magnesium alloys. The effect of anodizing on mechanical properties and microstructure was examined by repeated tension fatigue tests, tensile tests, hardness tests and electron microscopy.

Microstructure and Mechanical Properties of Eco-2024-T3 Aluminum Alloy

2012 ◽  
Vol 602-604 ◽  
pp. 623-626 ◽  
Author(s):  
Seon Ho Kim ◽  
Kyu Sik Kim ◽  
Shae K. Kim ◽  
Young Ok Yoon ◽  
Kyu Sang Cho ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Aluminum Alloy ◽  
Yield Strength ◽  
Fatigue Limit ◽  
Tensile Tests ◽  
Fatigue Tests ◽  
Economic Advantage ◽  
Microstructure And Mechanical Properties ◽  
Excellent Property

In this study, the microstructures and mechanical properties of the recently developed Eco-2024-T3 alloy were examined. Eco-2024 is made using Eco-Mg (Mg-Al2Ca) in place of element Mg during the manufacture of alloy 2024-T3. This is an alloy that has economic advantage and excellent properties. Alloy Eco-2024 showed smaller crystal grains that were distributed more evenly compared to the existing alloy 2024-T3. It consisted of Al matrices containing minute amounts of Al2CuMg, Al2Cu, and Ca phases and showed microstructures with reduced amounts of Fe phases or oxide. As a result of tensile tests, this alloy exhibited yield strength of 413 MPa, tensile strength of 527 MPa, and elongation of 15.4%. In other words, it showed higher strength than the existing alloy 2024 but was similar to the existing alloy 2024 in terms of elongation. In fatigue tests, alloy Eco-2024-T3 recorded fatigue limit of 330 MPa or around 80% of its yield strength; this is a much more excellent property compared to the existing alloy 2024-T3, which has fatigue limit of 250 MPa. Based on the aforementioned results, the correlation between the excellent mechanical properties of alloy Eco-2024-T3 and its microstructure was examined.

A New Wheel Design for Reducing Weight

2014 ◽  
Vol 794-796 ◽  
pp. 578-583 ◽  
Author(s):  
Frédéric Perrier ◽  
Véronique Bouvier ◽  
Lionel Duperray
Keyword(s):  
Mechanical Properties ◽  
Aluminum Alloy ◽  
Automotive Industry ◽  
Tensile Tests ◽  
Fatigue Tests ◽  
A356 Aluminum Alloy ◽  
Friction Stir ◽  
Forging Process ◽  
A356 Aluminum ◽  
Design Freedom

Reducing weight is one of the most important challenges in the automotive industry. A wheel design which enables to reduce weight from 13.5 kg to 10 kg is presented. This achievement is possible thanks to the use of a wide variety of technical processes. The disc is manufactured by CobapressTM, a casting/forging process which combines the advantages of a high design freedom, good mechanical properties and the absence of porosities. The alloy used is an A356 aluminum alloy modified with strontium. The rim is made of an AA6082 aluminum alloy which is extruded and flow-formed with a thickness from 3.3 down to 2.2 mm. Finally, the FSW (Friction Stir Welding) allows us to weld the two parts with a cavity to minimize the weight. With this technique the welding of the two different alloys is possible with good mechanical properties, the fracture happens outside of the weld during tensile tests. The final wheels passed bending and radial fatigue tests as well as radial impact tests with success.

Sign in / Sign up

Export Citation Format

Share Document