The Numerical Investigation of Stress Distribution on the Rake Face for Grooved Cutting Tool Inserts

2011 ◽  
Vol 223 ◽  
pp. 304-313
Author(s):  
E. Kwiatkowska ◽  
Piotr Niesłony ◽  
W. Grzesik
Keyword(s):  
Metal Cutting ◽  
Cutting Tool ◽  
Orthogonal Cutting ◽  
Cutting Tools ◽  
Cutting Process ◽  
Rake Face ◽  
Normal Stresses ◽  
Von Mises ◽  
Von Mises Stresses ◽  
Chip Breakage

The development of an accurate model for the shear and normal stresses on the rake face is very important for modeling of the metal cutting mechanics. It is known that the stresses vary over the contact surfaces of the tool and change substantially with their configurations. On the other hand, the recent attempts were generally addressed to orthogonal cutting process and tools with flat rake faces. At present, grooved tools with complex rake faces are commonly applied in the industry. In this study a plane strain finite element (FEM) program AdvantEdge was used to simulate the cutting process with some disposable grooved cutting tools. Both the reduced von Mises stresses and their components in x and y directions were considered and visualized for appropriate chip formation stages. In particular, the distribution of the contact stresses was revealed when chip breakage occurs. The simulated results were correlated with the geometry of the chip breaker and process parameters.

scholarly journals Predicting Cutting Force and Primary Shear Behavior in Micro-Textured Tools Assisted Machining of AISI 630: Numerical Modeling and Taguchi Analysis

Micromachines ◽  
2022 ◽  
Vol 13 (1) ◽  
pp. 91
Author(s):  
Shafahat Ali ◽  
Said Abdallah ◽  
Salman Pervaiz
Keyword(s):  
Tool Life ◽  
High Performance ◽  
Metal Cutting ◽  
Cutting Tool ◽  
Orthogonal Cutting ◽  
Cutting Tools ◽  
Cutting Temperature ◽  
Cutting Process ◽  
Cutting Fluids ◽  
Machining Performance

The cutting tool heats up during the cutting of high-performance super alloys and it negatively affects the life of the cutting tool. Improved tool life can enhance both the machinability and sustainability of the cutting process. To improve the tool life preferably cutting fluids are utilized. However, the majority of cutting fluids are non-biodegradable in nature and pose harmful threats to the environment. It has been established in the metal cutting literature that introducing microgrooves at the cutting tool rake face can significantly reduce the coefficient of friction (COF). Reduction in the COF promotes anti-adhesive behavior that improves the tool life. The current study numerically investigates the orthogonal cutting process of AISI 630 Stainless Steel using different micro grooved cutting tools. Results of the numerical simulations point to the positive influence of micro grooves on tool life. The results of the main effects found that the cutting temperature was decreased by approximately 10% and 7% with rectangular and triangular micro grooved tools, respectively. Over machining performance indicated that rectangular micro groove tools provided comparatively better performance.

Basic Mechanics of the Metal-Cutting Process

1944 ◽  
Vol 11 (3) ◽  
pp. A168-A175 ◽  
Author(s):  
M. Eugene Merchant
Keyword(s):  
High Speed ◽  
Metal Cutting ◽  
Cutting Tool ◽  
Orthogonal Cutting ◽  
Cutting Edge ◽  
Cutting Process ◽  
Work Piece ◽  
Machining Operations ◽  
Work Done ◽  
Metal Work

Abstract The author presents a mathematical analysis of the geometry and mechanics of the metal-cutting process, covering two common types of geometry which occur in cutting. This analysis offers a key for the study of engineering problems in the field of metal cutting in terms of such fundamental quantities as strain, rate of shear, friction between chip and tool, shear strength of the metal, work done in shearing the metal and in overcoming friction, etc. The two cases covered are, in essence, that of a straight-edged cutting tool moving relative to the work-piece in a direction perpendicular to its cutting edge, termed “orthogonal cutting,” and that of a similar cutting tool so set that the cutting edge is oblique to the direction of relative motion of tool and work, termed “oblique cutting.” Equations are developed which permit the calculation of such quantities as those just enumerated from readily observable values. The theoretical findings are particularly applicable and significant in the case of present-day high-speed machining operations with sintered-carbide tools.

Improving Tool Wear Resistance in Inconel 718 Cutting by Considering Surface Microstructures of CBN Cutting Tool

2016 ◽  
Vol 1136 ◽  
pp. 561-566
Author(s):  
Tatsuya Sugihara ◽  
Shota Takemura ◽  
Toshiyuki Enomoto
Keyword(s):  
Wear Resistance ◽  
Inconel 718 ◽  
Cutting Tool ◽  
Orthogonal Cutting ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Polished Surface ◽  
Rake Face ◽  
Crater Wear ◽  
Surface Microstructures

Nickel-based superalloys such as Inconel 718 are known as one of the most difficult-to-cut materials due to their mechanical and chemical properties and the tool life is extremely short. Recently, Cubic-Boron-Nitride (CBN) has received a considerable attention as a material for cutting tools and has been considered to be a major candidate for high performance cutting of Inconel 718. However, the detailed wear behavior of CBN tools in cutting of Inconel 718 is not sufficiently understood yet, and the performances of CBN tools are still insufficient in practical use. To overcome this problem, we first conducted orthogonal cutting experiments on Inconel 718 at low (20 m/min) and high (100 m/min) cutting speeds employing CBN cutting tools to clarify the detailed wear mechanisms. Moreover, relationship between surface microstructures of the cutting tool and wear resistance was investigated. As a result, it was found that a rake face with micro grooves significantly suppressed the crater wear at low cutting speed, although polished surface rake face reduced the initial crater wear by approximately 40 % compared to the non-polished tool in high speed cutting of Inconel 718.

The Effect of the Cutting Parameters on the Machined Surface Roughness

2017 ◽  
Vol 260 ◽  
pp. 219-226 ◽  
Author(s):  
Viktors Gutakovskis ◽  
Eriks Gerins ◽  
Janis Rudzitis ◽  
Artis Kromanis
Keyword(s):  
Surface Roughness ◽  
Metal Cutting ◽  
Cutting Tool ◽  
Cutting Tools ◽  
Cutting Parameters ◽  
Cutting Process ◽  
Tool Geometry ◽  
Machining Parameters ◽  
Machined Surface ◽  
Machined Surface Roughness

From the invention of turning machine or lathe, some engineers are trying to increase the turning productivity. The increase of productivity is following after the breakout in instrumental area, such as the hard alloy instrument and resistance to wear cutting surfaces. The potential of cutting speed has a certain limit. New steel marks and cutting surfaces types allow significantly increase cutting and turning speeds. For the most operation types the productivity increase begins from the feeding increase. But the increase of feeding goes together with machined surface result decreasement. Metal cutting with high feeding is one of the most actual problems in the increasing of manufacturing volume but there are some problems one of them is the cutting forces increasement and larger metal removal rate, which decrease the cutting tool life significantly. Increasing of manufacturing volume, going together with the cutting instrument technology and material evolution, such as the invention of the carbide cutting materials and wear resistant coatings such as TiC and Ti(C,N). Each of these coating have its own properties and functions in the metal cutting process. Together with this evolution the cutting tool geometry and machining parameters dependencies are researched. Traditionally for the decreasing the machining time of one part, the cutting parameters were increased, decreasing by this way the machining operation quantity. In our days the wear resistance of the cutting tools increasing and it is mostly used one or two machining operations (medium and fine finishing). The purpose of the topic is to represent the experimental results of the stainless steel turning process, using increased cutting speeds and feeding values, to develop advanced processing technology, using new modern coated cutting tools by CVD and PVD methods. After investigation of the machined surface roughness results, develop the mathematical model of the cutting process using higher values of the cutting parameters.

scholarly journals EFFECT OF CUTTING SPEED IN THE TURNING PROCESS OF AISI 1045 STEEL ON CUTTING FORCE AND BUILT-UP EDGE (BUE) CHARACTERISTICS OF CARBIDE CUTTING TOOL

SINERGI ◽  
2020 ◽  
Vol 24 (3) ◽  
pp. 171
Author(s):  
Sobron Yamin Lubis ◽  
Sofyan Djamil ◽  
Yehezkiel Kurniawan Zebua
Keyword(s):  
Cutting Force ◽  
Metal Cutting ◽  
Cutting Tool ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Cutting Process ◽  
Depth Of Cut ◽  
Aisi 1045 Steel ◽  
1045 Steel

In the machining of metal cutting, cutting tools are the main things that must be considered. Using improper cutting parameters can cause damage to the cutting tool. The damage is Built-Up Edge (BUE). The situation is undesirable in the metal cutting process because it can interfere with machining, and the surface roughness value of the workpiece becomes higher. This study aimed to determine the effect of cutting speed on BUE that occurred and the cutting strength caused. Five cutting speed variants are used. Observation of the BUE process is done visually, whereas to determine the size of BUE using a digital microscope. If a cutting tool occurs BUE, then the cutting process is stopped, and measurements are made. This study uses variations in cutting speed consisting of cutting speed 141, 142, 148, 157, 163, and 169 m/min, and depth of cut 0.4 mm. From the results of the study were obtained that the biggest feeding force is at cutting speed 141 m/min at 347 N, and the largest cutting force value is 239 N with the dimension of BUE length: 1.56 mm, width: 1.35 mm, high: 0.56mm.

Cutting Process Analysis for Uniform and Variable Edge Tools

2010 ◽  
Vol 37-38 ◽  
pp. 280-283
Author(s):  
Zhao Li ◽  
Ai Bing Yu ◽  
Hao Wang ◽  
Liang Dong
Keyword(s):  
Cutting Forces ◽  
Cutting Tool ◽  
Process Analysis ◽  
Orthogonal Cutting ◽  
Cutting Tools ◽  
Cutting Process ◽  
Fem Modeling ◽  
Temperature Distributions ◽  
Aisi 1045 Steel ◽  
1045 Steel

Tool edge geometry has obvious influences on cutting tool behaviors. FEM modeling and simulation of orthogonal cutting process using uniform and variable edge cutting tools were studied with dynamics explicit ALE method. AISI 1045 steel was chosen for workpiece, and cemented carbide was chosen for cutting tool. Three sections of uniform and variable edges were chosen for analysis. Cutting forces and temperature distributions were calculated for uniform and variable edge carbide cutting tool. Simulation results show that variable edge cutting tool obtains small cutting forces. Ploughing force tends to reduce when variable edge cutting tool was used. Variable edge cutting tool reduces the heat generation and presents reasonable temperature distributions, which is beneficial to cutting life. The force and temperature distributions demonstrate the advantages of variable edge cutting tool.

Hard Nano-Crystalline Coatings for Cutting Tools

2007 ◽  
Vol 567-568 ◽  
pp. 185-188 ◽  
Author(s):  
Miroslav Piska
Keyword(s):  
High Speed ◽  
Metal Cutting ◽  
Cutting Tool ◽  
Cutting Tools ◽  
Dry Cutting ◽  
Nano Crystalline ◽  
The Right ◽  
Machining Productivity ◽  
Hard Cutting ◽  
Cutting Tool Materials

Modern trends in metal cutting, high speed/feed machining, dry cutting and hard cutting set more demanding characteristics for cutting tool materials. The exposed parts of the cutting edges must be protected against the severe loading conditions and wear. The most significant coatings methods for cutting tools are PVD and CVD/MTCVD today. The choice of the right substrate or the right protective coating in the specific machining operation can have serious impact on machining productivity and economy. In many cases the deposition of the cutting tool with a hard coating increases considerably its cutting performance and tool life. The coating protects the tool against abrasion, adhesion, diffusion, formation of comb cracks and other wear phenomena.

scholarly journals Preparation and cutting performance of nano-scaled Al2O3-coated micro-textured cutting tool prepared by atomic layer deposition

2021 ◽  
Vol 40 (1) ◽  
pp. 77-86
Author(s):  
Siwen Tang ◽  
Pengfei Liu ◽  
Zhen Su ◽  
Yu Lei ◽  
Qian Liu ◽  
...  
Keyword(s):  
Friction Coefficient ◽  
Atomic Layer Deposition ◽  
Cutting Force ◽  
Cutting Tool ◽  
Orthogonal Cutting ◽  
Cutting Tools ◽  
Atomic Layer ◽  
Cutting Performance ◽  
Cutting Test ◽  
Layer Deposition

Abstract Al2O3 nano-scaled coating was prepared on micro-textured YT5 cemented carbide cutting tools by atomic layer deposition ALD. The effect of Al2O3 nano-scaled coating, with and without combined action of texture, on the cutting performance was studied by orthogonal cutting test. The results were compared with micro-textured cutting tool and YT5 cutting tool. They show that the micro-texture and nano-scaled Al2O3 coated on the micro-texture both can reduce the cutting force and friction coefficient of the tool, and the tools with nano-scaled Al2O3 coated on the micro-texture are more efficient. Furthermore, the friction coefficient of the 100 nm Al2O3-coated micro-texture tool is relatively low. When the distance of the micro-pits is 0.15 mm, the friction coefficient is lowest among the four kinds of pit textured nanometer coating tools. The friction coefficient is the lowest when the direction of the groove in strip textured nanometer coating tool is perpendicular to the main cutting edge. The main mechanism of the nanometer Al2O3 on the micro-textured tool to reduction in cutting force and the friction coefficient is discussed. These results show that the developed tools effectively decrease the cutting force and friction coefficient of tool–chip interface.

scholarly journals Dispositivos De Interrupcion Subia (Dis) Para El Analisis De Raices Viruta

2014 ◽  
Vol 2 (2) ◽  
Author(s):  
Diego Alejandro Neira Moreno
Keyword(s):  
Cutting Tool ◽  
Cutting Tools ◽  
Scientific Research ◽  
Cutting Process ◽  
Work Piece ◽  
Mechanical Forces ◽  
Machining Processes ◽  
Research Instrument ◽  
Machined Parts ◽  
Interaction Phenomena

El estudio de las variables y efectos derivados del mecanizado provee herramientas de conocimiento tendientes a optimizar el uso de las herramientas y los procedimientos de maquinado industrial. Este artículo de reflexión aborda el uso de los dispositivos de interrupción súbita (DIS) como herramientas de obtención de raíces de viruta para la investigación científica del mecanizado industrial, y para el estudio de los efectos derivados de la interacción entre las herramientas de corte y el material de trabajo, en función de los cambios microestructurales del material de trabajo, dependientes de la temperatura producida y los esfuerzos mecánicos de la herramienta de corte durante el mecanizado. Mediante la reflexión se destaca la importancia de los DIS como instrumentos de investigación científica en la manufactura, ya que estos permiten obtener muestras de viruta para estudiar las variables incidentes en el maquinado y a partir de esta evidencia, proponer alternativas para optimizar la fabricación de piezas y la integridad de las herramientas empleadas en el proceso.AbstractThe study of the variables and effects derived from the machining processes brings the knowledge needed to optimize the use of machining tools and procedures. This article is an opinion piece about the use of quick stop devices (QSD) as a scientific research instrument in machining projects to obtain chip roots, to study the interaction phenomena between cutting tool and work piece material that depends on temperature and the mechanical forces produced by the cutting tool during the cutting process. This article deals about how important the QSD are as a research instruments in manufacture because with this instruments it is possible to analyze the machining variables, based on the evidences bring by the chip roots obtained with the instrument. It is possible to propose optimization alternatives in the manufacture of machined parts and the integrity of cutting tools.

Role of energy consumption, cutting tool and workpiece materials towards environmentally conscious machining: A comprehensive review

2019 ◽  
Vol 234 (3) ◽  
pp. 335-354 ◽  
Author(s):  
Salman Pervaiz ◽  
Sathish Kannan ◽  
Ibrahim Deiab ◽  
Hossam Kishawy
Keyword(s):  
Energy Consumption ◽  
Metal Cutting ◽  
Cutting Tool ◽  
Cutting Process ◽  
Machining Process ◽  
Workpiece Material ◽  
Tool Materials ◽  
Wide Range ◽  
Cutting Operation

Metal-cutting process deals with the removal of material using the shearing operation with the help of hard cutting tools. Machining operations are famous in the manufacturing sector due to their capability to manufacture tight tolerances and high dimensional accuracy while simultaneously maintaining the cost-effectiveness for higher production levels. As metal-cutting processes consume a great amount of input resources and generate some material-based waste streams, these processes are highly criticized due to their high and negative environmental impacts. Researchers in the metal-cutting sector are currently exploring and benchmarking different activities and best practices to make the cutting operation environment friendly in nature. These eco-friendly practices mainly cover the wide range of activities directly or indirectly associated with the metal-cutting operation. Most of the literature for sustainable metal-cutting activities revolves around the sustainable lubrication techniques to minimize the negative influence of cutting fluids on the environment. However, there is a need to enlarge the assessment domain for the metal-cutting process and other directly and indirectly associated practices such as enhancing sustainability through innovative methods for workpiece and cutting tool materials, and approaches to optimize energy consumption should also be explored. The aim of this article is to explore the role of energy consumption and the influence of workpiece and tool materials towards the sustainability of machining process. The article concludes that sustainability of the machining process can be improved by incorporating different innovative approaches related to the energy and tool–workpiece material consumptions.

Sign in / Sign up

Export Citation Format

Share Document